Painting with Tharmo plastic Paint Centre line on junction, edge line, cut patta, Zibra crossing, Bump Patta on T.P. Road in Ghatlodia Ward, North West Zone. (ARC)

Name of Work :- Painting with Tharmo plastic Paint Centre line on junction, edge line, cut patta, Zibra

crossing, Bump Patta on T.P. Road in Ghatlodia Ward, North West Zone. (ARC)

Quantity Item Unit Rate Amount

Road marking with hot applied Thermoplastic

Paints with reflectorising glass beads on bitumin

surface providing and laying a hot applied

thermoplastic compound 2.5 mm thick including

reflectorising glass beads @ 250gms per sqm

area, thickness of 2.5mm is excluding of surface

applied glass beds as per IRC:35-2015. The

finished surface to be level, uniform and free from

streaks and holes.zebra patta /bump patta

1 1800.00 lane/center line/ edge line/cut patta. The white Smt 364.08

color marking should provide liminance coefficinet

on cement road shall be min 130 mcd/m2/lux and

Asphalt road shall be min100mcd/m2/lux during

the service life during the daytime.The marking

should meet the performance criteria for night time

reflectivity,wet reflectivity and skid resistance as

mentioned in the section-15of IRC35-

2015.Warranty for the Retro reflectivity should be

Road marking with hot applied thermoplastic

paints with reflectorising glass beads on bitumin

surface providing and laying a hot applied

thermoplastic compound 2.5 mm thick including

2 1.00 reflectorising glass beads @ 250gms per sqm area, Nos. 512.95

thickness of 2.5mm is excluding of surface applied

glass beds as per IRC:35. The finished surface to

be level, uniform and free from streaks and holes.)

Directional Arrow, Lettering.

Cat Eye/ Road Stud/ RPM: Supplying of Molded

Twin Shanks Raised Pavement Markers made of

polycarbonate and ABS moulded body and

reflective panels with micro prismatic lens (No

glass bed lens) capable of providing total internal

reflection of the light entering the lens face and

shall support a load of 13635 kgs .tested in

accordance to ASTM D 4280 Type Hand complying

to Specifications of Category A of MORTH Circular

No RW/NH/33023/10-97-DO III Dt 11.06.1997

.The height, width and length shall not exceed

mm, 130 mm and 130 mm and with minimum

reflective area of 13 Sqcm on each side and the

slope to the base shall be 35 +/- 5 degree.The

strength of detachment of the integrated

cylindrical shanks, (of diameter not less than

+/- 2mm and height not less than 30 +/-2 mm)

from the body is to be a minimum value of

Kgf. Fixing will be by drilling holes on the road for

the shanks to go inside,without nails and using

epoxy resin based adhesive as per manufacturers

recommendation and The color of the marker

should be as per the IRC35-2015 and as directed

by Engineer-in-charge.

C.R. Base Road Marking Painting lines, dashes,

arrow, letters etc. on Road, Air fields and like in

4 two coats with road road marking paint , brushing

including cleaning the surface of all dirt, dust and

other foreign matter.

Over 10 cm in width

C.R. Base Road Marking Painting lines, dashes,

arrow, letters etc. on Road, Air fields and like in

4.00 two coats with road road marking paint , brushing Rmt 6.84

including cleaning the surface of all dirt, dust and

other foreign matter. (ii) Up to 10 cm in width

RETRO –REFLECTORISEED TRAFFIC SIGN

Cautionary signage 60cm equilateral triangle plus

60 cm x 20cm rectangular additional plate.

Providing and fixing of reflectorised cautionary,

mandatory and Informative sign as per IRC-67-

2012 made of micro prismatic grade sheeting as

per ASTM 4956-09 Type -XI fixed over 4 mm thick

Aluminum Composite Material supported With

frame fabricated from suitable size MS angle

40mm x 40mm x 5mm square box or equilateral

triangle as required on a mild steel angle iron post

65mm NB MS MW pipe or equivalent MS Pipe

section firmly fixed to the ground. The total

height of pole/Stand post is 3.3 mt and clear

height is 2.1 from the footpath top or ground level

by means of properly designed foundation with

M25 grade cement concrete 45cmx45cmx60cm

below footpath/ ground level as per approved

drawing including excavation, curing etc.

complete under the supervision of engineer In

Charge. The pole shall be Painted with best

Quality epoxy coating in Black and white Bends.

The details of symbol for each board shall be as

per the instruction of engineer incharge

Painting Two Coats on divider and footpath curb

surface / New Concrete Surface ( Painting two

6 720.00 coats after filling the surface with synthetic Smt 71.86

enamel paint in all shades on new plastered

concrete surfaces) (AMC approved Rate )

Supplying And Fixing Jumbo bollard swiss

typeMade out of 1.5 cm crc sheet height

cms.Bottom dia 30 cms. Top dia 18cm.

Withdirection plate of 45cm dia. Fabricated as

perattached drawing, pre treated with

phosphetingprocess painted with apoxy

coatingreflectorised with retro reflective

sheetingsspecified by M.O.R.T & H.'s latest

specification.(B)High Intensity Grade. (AMC

Providing and fixing Swiss type bollard made outof

1.5mm CRC sheet ,height140cms,bottom dia

23cm,top dia 12cm withdirection plate of 30 cm

dia fabricatednecessary anchors as directed and

also providethrough out lengh pipe of 25 NB for

8 1.00 hestrenthing of bollard and reflectorised Nos. 3696

icroPrismatic Grade Sheet (Type XI)and

threeyellowstrip 6 Inches wide of Type XI

etroreflective Sheeting, fixing with P.C.C M25

adeconcrete(Foundation size 0cm×30cm×35cm).

(AMCapproved rate)

Fexible Median Marker : Providing and Fixing of

Flexible Median Marker that are made of tough,

high impact resistant, injection-molded,

thermoplastic body with property of flexibility to

provide high durability. The dimension of Flexible

Median Marker should not exceed 18.4 cm in

height(including shank height),12.5 Cm in width.

,0.65 cm in thickness and shank depth shall be

cm The body structure shall be rounded at all its

corners and edges. The plastic used for molding

the Flexible Median Marker should survive impact

load of 5kg continuously for 750 times at room

temperature. The logo of the manufacturer shall

be embossed on either side of the body in the

injection molding process. The Median Marker

shall have flame like shaped body with,

fluorescent yellow color retro-reflective sheeting

of size not less than 90 Cm square, with fully

reflective micro prismatic cube corners as its

retro-reflective elements as per IRC 67 2012 and

ASTM D4956-09 type XI specifications reflectivity

values. The retro-reflective sheeting shall be one

or both sides of the Flexible Median Marker and

shall be edge protected with no exposed edges

which will prevent edge lifting, vandalism,

sheeting damage, etc. The Flexible Median Marker

shall be fixed by a combination of epoxy adhesive

and grouting as recommended by.

RETRO –REFLECTORISEED TRAFFIC SIGN

Mandatory Signage 60cm circular plus 60 cm x

20cm rectangular additional plate. Providing and

fixing of reflectorised cautionary, mandatory and

Informative sign as per IRC-67-2012 made of

micro prismatic grade sheeting as per ASTM 4956-

09 Type -XI fixed over 4 mm thick Aluminum

Composite Material supported With frame

fabricated from suitable size MS angle 40mm x

40mm x 5mm square box or circular as required

on a mild steel angle iron post 65mm NB MS MW

pipe or equivalent MS Pipe section firmly fixed to

the ground. The total height of pole/Stand post is

3.3 mt and clear height is 2.1 from the footpath

top or ground level by means of properly designed

foundation with M25 grade cement concrete

45cmx45cmx60cm below footpath/ ground level

as per approved drawing including excavation,

curing etc. complete under the supervision of

engineer In Charge. The pole shall be Painted with

best Quality epoxy coating in Black and white

Bends. The details of symbol for each board shall

be as per the instruction of engineer in charge.

8 12.00 RETRO–REFLECTORISEED TRAFFIC SIGN

Informatory signage 60cmx45cm rectangular plus

45 cm x 20cm rectangular additional plate.

Providing and fixing of reflectorised cautionary,

mandatory and Informative sign as per IRC-67-

2012 made of micro prismatic grade sheeting as

per ASTM 4956-09 Type -XI fixed over 4 mm thick

Aluminum Composite Material supported With

frame fabricated from suitable size MS angle

40mm x 40mm x 5mm rectangular box as

required on a mild steel angle iron post 65mm NB

MS MW pipe or equivalent MS Pipe section firmly

fixed to the ground. The total height of pole/Stand

post is 3.3 mt and clear height is 2.1 from the

footpath top or ground level by means of properly

designed foundation with M25 grade cement

concrete 45cmx45cmx60cm below footpath/

ground level as per approved drawing including

excavation, curing etc. complete under the

supervision of engineer In Charge. The pole shall

be Painted with best Quality epoxy coating in

Black and white Bends. The details of symbol for

each board shall be as per the instruction of

engineer incharge.

Hazard Marker Sign :-Providing and fixing sign

boards made out of 2.0 mm aluminium sheet /

mm ACP (Aluminum composite Panel); size

90x30 cms. rectangular as per design of IRC-67-

2022. Pre treated with phospheting process &

acid etching; coated with one coat of epoxy

primer and two coats of best quality epoxy

paint ;reflectorised with Micro Prismatic Grade

retro refiectivesheeting of Type-11 as per ASTM

D-4956 and latest M.O.S.T.Specifications;

1.8mtr long stand post of 75 x 75 x 6mm /

65NB Circular MS Pipe as required and frame

fabricated from suitable size iron angle of 35 x

x 3mm; painted with bestquality epoxy

coatings in black and white bends. The details

of symbol foreach board shall be as per

theinstruction of engineer in charge. The fixing at

site shall be in 1:2:4 CC blockof size 45 x 45 x

Cms. for each leg.including excavation, curing

etc.complete under the supervision of engineer

in charge. A warranty for 10 years for the Retro

reflective sheeting from original manufacturer

& a certified copy of 3 year outdoor

exposure test report from third party test lab

for the product offered shall be submitted

by contractor. (A) Class-C Type-11 Retro

Reflective sheeting

Give Way Sign :-Providing and fixing sign

boards made out of 2mm aluminium sheet /

4mm ACP (Aluminum composite Panel); size 90 x

90 x 90 cms. equilateral triangle as per design of

IRC-67-2022. Pre treated with phospheting

process & acid etching; coated with one coat of

epoxy primer and two coats of best quality

epoxy paint ;reflectorised with Micro Prismatic

Grade retro refiectivesheeting of Type-11 as per

ASTM D-4956 and latest M.O.S.T.Specifications;

3.6mtr long stand post of 75 x 75 x 6mm / 65NB

Circular MS Pipe as required and frame fabricated

from suitable size iron angle of 35 x 35 x 3mm;

13 1.00 painted with bestquality epoxy coatings in Nos. 4055.42

black and white bends. The details of symbol

foreach board shall be as per theinstruction

of engineer in charge. The fixing at site shall be in

1:2:4 CC blockof size 45 x 45 x 60 Cms. for each

leg.including excavation, curing etc.complete

under the supervision of engineer in charge. A

warranty for 10 years for the Retro reflective

sheeting from original manufacturer & a

certified copy of 3 year outdoor exposure

test report from third party test lab for the

product offered shall be submitted by

contractor. (A)Class-C Type-11 Retro Reflective

Directional board : Providing and fixing Directional

sign boards made out of 4mm. Aluminum

composite Panel (ACP) in cubical shape of

dimensions 153cm x 122cm x 17cms (avg.) Framed

on 25x25x5 Equal angle sections as per drawing

including sufficient horizontal support and

diagonal bracing to withstand static as well as

14 1.00 dynamic (WIND LOAD) after mounting it on Nos. 21664.72

100x100x3.6 mm. M.S.Square Hollow

Section(CHS) with 6 mm. M.S.Plates and stiffeners

in such a manner that they are not visible from

out side. The composite panel face is covered with

micro prismatic grade Sheeting confirming to type

XI as per ASTM-D 4956-09. It should bear

minimum 10 Yrs. outdoor exposed performance

supported by the Reflective-Sheeting manufacture

is having legal jurisdiction in India. The letters

(dual languages), symbols, borders shall be made

of same material either by screen printing or by

cut sheet lettering as recommended by the

sheeting manufacture.The board sides (Top,

Bottom, Sides and back side) are covered with

round 4 MM Aluminium composite Panel(ACP)

Blue Color sheet .The board sides are fabricated

with 25x 6mm ms flat in round shape . The sign

shall be installed at site on MB110 MS CHS. at

mt. clear bottom height from the pavement in

M25 grade cement concrete block of 0.45m x

0.45m x 0.90m dimensions as directed by the

Engineer in charge. Total length of pole will be of

4.53 m height. Back side of directional board shall

be made of Flex board maintaining with

Ahmedabad Municipal Corporation letters and its

logo according to instruction of Engineer -In

charge. Nothing shall be paid for carting from

factory to the fixing site within AMC limit.

Providing And fixing 750mmX250mmX75

mm size Speed breakers made up of ABS

(Aerylonitrile butdadiene styrene plastic

dark eye/alcolite with interlocking facility

U.B.Stabilized refleted on eitherside

moulded in PMMA Matrial with ABS Base

plate though ultrasonick welding

processand then fixed on speed rumpnad

theses maintainreflecting for longer time.

the speed breaker to be fixed on the Road

with help of epoxyand metalick bolt of as

per specified by manufacturer etc. complete

and as per direction of engineer incharge

rate including all fixing labour , loading,

unloading, leading and all taxes. The bump

is having skid resistance base and

combination in yellow and black UV

Stabilized colours No digging is permited on

the surface. Nothing extra will be paid

whatsoever the case may be

Speed breaker of 750 mmX250mmX75 mm

Spring post : Supply and fixing of Spring post

extremly flexible and soft so as not to damage

the vehicle the vehicle at collision and to be

restored soon at its original. The material of

the body should be UV stabilised and non-

16 1.00 fading color with 3 bands of high quality of Nos. 1320.00

Reflective sheeting of min 50mm. The Height

of the post should be 800mm, Top dia of

80mm and base should be 200mm, complete

with fixing at site with nails/ anchor fasters as

directed by Engineer incharge.