Repair to leakage, seepage, joinery, flooring, ceiling, sanitary fittings, plastering, painting, approach path, drain and internal electrification of Offrs MD Accn at SP road / Beecher road under GE Dehradun

Amount

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) (using old size bricks) complete all as specified and directed.

All as per serial item No. 2.00 here in above but except bricks.(Bricks obtained from dismantling shall be reused)

M&L for brick work with subclass 'B' bricks, straight or curved on plan to any radius built in cement mortar (1:4) as in half brick thick wall (using old size bricks) complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified

M&L rendering 15m thick on fair faces of brick work in CM 1:4 in two layers (1st layer 10-12mm + 2nd layer 3-5mm) and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

M&L rendering 15m thick on fair faces of brick work in CM 1:6 in two layers (1st layer 10-12mm + 2nd layer 3-5mm) and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

M&L for applying wall putty 2 to 3 mm thick and rubbing with sand paper on plastered surfaces of walls after preparation of surfaces complete all as specified and directed

M&L for preparation of old decorative surface of wall (plastered) by brooming down with coir brush and hand held electrical grinder, scraping down smoke soot, moulds, moss and efflorecent salts and trading oil and greasy spots and finally cleaned with sand paper all as directed by Engr-in-charge

Complete removal of existing treatment of wall upto the plastered surface of wall by brooming down with steel wire brush and hand held electrical grinder, scraping down smoke soot, moulds, moss and efflorecent salts and trading oil and greasy spots and finally cleaned with sand paper all as directed by Engr-in-charge

M&L preparation of old decorated surfaces of ceiling (Plastered) by brooming down or sand paper, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots all as directed by Engr-in-charge.

M&L for applying one coat of oil bound distemper on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge.

M&L for preparation of new plastered / POP / Putty surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed by Engr-in-charge

M&L for preparation of new plastered / POP / Putty surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed by Engr-in-charge

M&L for applying one coat of cement base paint on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge.

M&L for preparation of new plastered / POP / Putty surfaces of walls and applying two coats of exterior grade 1st quality weather proof paint over a coat of alkali resistant priming paint complete all as specified and directed. Make: Berger XP advance, Asian paints (Apex ultima), Nerolac (Excel total).

M&L for applying one coat of exterior grade 1st quality weather proof paint on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge. Make : Berger XP advance, Asian Paints (Apex Ultima), Nerolac (Excel total)

M & L preparation of new surfaces of wood & wood based material of any description over 10 cm width or girth and applying two coats of PU Paint over a coat of pink primer complete.

M & L preparation of old painted surfaces of wood & wood based material of any description over 10 cm width or girth and applying one coat of PU Paint complete.

M & L preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as speciied and directed.

M & L preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as speciied and directed.

Cutting around the pipe 75/100mm bore waste / soil pipe including taking out plant roots up to any depth in brick masonary and rejointing in pipe joint in epoxy mortar (Asian/Berger) and making good to existing surface all as directed by Engr-in-charge. (After the jointing pipe one week to be open for checking of leaking including scaffolding)

Removing / cutting trees vegetation, digging out roots from concrete or brick wall, filling holes on building (Block of 4 qtrs) wall / roof / chajja etc applying and making good with epoxy mortar (Asian/Berger) and applying surface treatment to match with existing specifications complete.

M&L rendering in patches (nexc 3.0 Sqm) 15m thick on fair faces of brick work in CM 1:4 and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge(Note : WPC measured and paid saperately)

M & L rendering 10mm thick in patches n exc 3 Sqm in cement mortar 1:3 on fair faces of concrete surfaces, chajja/ facia finished even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc.

M&L for applying one coat of white wash on old decorated already prepared surfaces of ceiling complete all as specified and directed by Engr-in-charge.

M & L 10 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling, surface finished fair and even complete.

M&L for preparation of new plastered / POP / Putty surfaces of ceilings and applying three coats of white wash complete all as specified and directed by Engr-in-charge

Dismantling wall tiling including cement mortar bedding (but not backing), and removing rubbish off the MD land complete all as specified.

Dismantling floor tiles including cement mortar bedding (but not backing), and removing rubbish off the MD land complete all as specified.

Demolition of cement concrete in ground floor and paving nexc 15cm thick (below or above ground level ) and removing rubbish off the MD land complete all as specified.

Demolition of (unreinforced) cement concrete of any description and in any position not otherwise specifically provided for and removing rubbish off the MD land complete all as specified..

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing rubbish off the MD land complete all as specified..

M&L non skid mat finish ceramic colour tiles of size 300x300 mm x 6-7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

M&L non skid mat finish designer coloured joint free ceramic tiles of size not less than 400x400 mm x 6-7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

All as per item No 36.00 here in above but as in skirting including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M & L for Glazed ceramic coloured tiles of size 300X600 mm X 6- 7 mm thick or 450X350 mm X 7 mm thick on vertical surfaces such as skirting, dados and rises to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with colour cement to match the surface including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

M&L for ceramic coloured vitrified tiles area of each tile not exc 0.36 sqm, 10mm thick in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

All as per item No 39.00 here in above but as in skirting including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 (usng 12.5 mm graded stone aggregate) as in leveling course to floors complete all as specified and directed.

M & L for PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in benching to drain, holdfast, padding to roof/chhajja, coping, bed block etc. and the like edge slightly rounded or chamfered including necessary use and waste of form work complete all as specified and directed..

M & L for 75mm thk PCC 1:3:6 type C-2 as in plinth protection, finished even and fair without using extra cement. The plinth protection shall be laid in alternate bays nexe 2 sqm with 10mm wide joints filled with bitumen mastic comprising of 1 part of hot bitumen 85/25 grade and 3 parts sand all by weight complete all as specified.

M & L for PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling, mass concrete, sub base or leveling course of floor etc. complete all as specified and directed.

M & L for cement concrete ( 1:3:6 ) type C1 (using 20 mm graded stone aggregate) as in surface channels and drains and benching, forming fair finished channel for drain using extra cement including necessary form work complete all as specified.

M&L for 40 mm thick plain cement concrete 1:2:4 type B-1 ( 20 mm graded aggregate) as in floor finished even and smooth without using extra cement. complete all as specified and directed by Engr-in-charge

Dismantling of stone slab and tiles of any description or thickness in floor, apron etc. set in cement mortar complete all as specified and directed .

M&L for 18-20 mm thick machine cut polished granite 1st quality "black" stone slab over kitchen platform and similar places over and including 15mm thick screed bed in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match with existing surface, rounding off exposed edges complete all as specified and as directed.

M & L for heavy duty endura ceramic coloured tiles of size 300X300 mm X10 mm thick in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

Taking down, resecuring/repair of wooden shutters of any description exc 1 sqm but n exc 2.0 sqm each and refixing in same opening including painting to match existing surface complete all as specified and directed by Engr-in-charge

Taking down shutters of any description not exc. 1 Sqm each and removing from site complete all as specified and directed.

All as per item No 51.00 here in above but exc 1 Sqm but n. exc 2 Sqm each complete all as specified and directed.

Taking down Chowkats with shutter (without taking off shutters) area not exceeding 1.5 Sqm each and removing from site complete all as specified and directed.

Taking down Chowkats with shutter (without taking off shutters) area exceeding 1.5 Sqm but not exceeding 4 Sqm each and removing from site complete all as specified and directed.

M&L for second class hard wood, plain, solid, straight chowkats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engr-in-charge

S & F 35mm thick second class hardwood glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24 (a) and as directed.

S&F factory made 100 % solid wood plastic composite (WPC) door frame 125 x 63 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing as directed by Engineer-in-Charge Make : ECHON/Kumar Tech/Sintex

S&F 30 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified. Make : ECHON/Kumar Tech/Sintex

S&F Factory made solid Fibre reinforcement plastic (FRP) frame of size 75x50mm the rasin of chemical used in door of unsaturated polyester rasin catagory, cataylst used of methyl Ethyl Ketone peroxide (MEKP)/benzyl peroxide/acetyl aceto peroxide. Accelerator used of cobalt napthalate/cobalt octonate/N.N Dinethyl aniline. Timber suitable for manufacturing of FRP products is in accordance with IS 12896. The timber used for frames is seasoned upto the permissible moisture content as per IS-287 : 1993. Pigment compatible with unsaturated polyester resin is used to obtain the shade of finish complete all as specified and directed by the Engineer-in-Charge.

S&F Factory made solid panel Fibre reinforcement plastic (FRP) door shutter 30mm thick consisting of frame top & bottom rails as per SSR Part I, any number of panels, the rasin of chemical used in door of unsaturated polyester rasin catagory, cataylst used of methyl Ethyl Ketone peroxide (MEKP)/benzyl peroxide/acetyl aceto peroxide. Accelerator used of cobalt napthalate/cobalt octonate/N.N Dinethyl aniline. Timber suitable for manufacturing of FRP products is in accordance with IS 12896. The timber used for frames is seasoned upto the permissible moisture content as per IS-287 : 1993. Pigment compatible with unsaturated polyester resin is used to obtain the shade of finish complete all as specified and directed by the Engineer-in-Charge.

M/L 30mm thick 2nd class hard wood factory made Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) all as directed by Engr-in-Charge.

M/L 30mm thick 2nd class hard wood factory made Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) all as directed by Engr-in-Charge.

M&L for 30 mm thick, factory made BWR flush shutters, solid core construction, with block board core and plywood face pannels commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for structural steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging with and including either hooks and hinges or steel hanging door fittings and fixing complete, structural steel conform to Fe 410w (Gde & 250) quality 'A' all as specified and directed.

M&L for 1.25 mm thick mild steel plain black sheet in covering to door shutters covering to door chowkhats, water troughs, urinal troughs and funnels and the like cut to size edges based it directed, holes punched, including round head screws clout nails or rivets fixed to wood or steel member etc with plain 40mm lap joints or welded/reveted scans including bending turning up, mitred angle, stop ends outlet etc as required complete all as specified and directed by Engr-in-Charge.

S&F in repair Factory made Steel windows with side hung shutters with box type hinges including steel handle, steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-charge

S&F in repair Factory made Steel windows with side hung shutters with box type hinges including steel handle, steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-charge

S&F in repair factory made steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed.

Taking down existing projected type hings from the steel window carefully with disturbing frame and fix 50 mm long mild steel box type hinge weld to steel frame and shutter with welding and making good including touch with paint and with existing surfaces including scaffolding all as directed by Engr-in-charge.

S&F powder coated aluminium ventilator fixed type half glazed and half gauged with and including hardware fittings, glazing, wire gauge, rubber packing, aluminium beading etc. as specified below including taking down old window/ventilator and making good of wall surface to match with existing surface complete all as specified and directed : - Frame : 44.5 x 44.5 mm x 1.80 mm thick Middle rail : 44.5 x 44.5 mm x 1.80 mm thick Glazing: 5 mm thick frosted glass fixed with rubber gasket and aluminium beading. Wire gauge: stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm fixed with aluminium beading.

S&F powder coated aluminium grill with frame fixed to by means stainless steel screws complete all as specified and directed.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with tinned tacks or stainless steel wire staples all as directed by Engeer-in-charge.

S&F in repair stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with tinned tacks or stainless steel wire staples all as directed by Engeer-in-charge.

S&F 4 mm thick sheet glass ordinary quality and glazing with silicon and oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane all as directed by Engeer-in-charge.

S&F in repairs 4 mm thick sheet glass ordinary quality and glazing with silicon and oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane all as directed by Engeer-in-charge.

S&F mild steel framed work as in grill, grating etc framed guard bars, barred iron doors, ladders, frame balusters, walk ways, railing. framed work of water tanks and similar works confirming to Fe 290 Gde E165 complete all as specified and directed.

S&F in repairs 18 mm thick PVC ply one side prelaminated and other side plain white colour as in cup board shutters and frames complete all as specified and directed by the Engineer-in-Charge. Make:-Rajshree, Polyline, ECHON/Kumar Tech

S&F in repairs 18 mm thick plain white PVC sheet as in cup board shelves, partition, drawer etc complete all as specified and directed by the Engineer-in-Charge. Make:-Rajshree, Polyline, ECHON/Kumar Tech

S&F continious (Piano) hinges, mild steel, bright finish or electrogalvanised. 30 mm width of flaps (when open) complete all as specified as directed.

S&F Hasp and staple 100mm safety type, stainless steel 304 grade with hinge pin including bolt to hinge plate and fixed with screws complete all as specified as directed.

S&F 75 mm size stainless steel butt hinges and fixed with stainless steel screws, complete all as specified and directed by Engr-in-Charge.

S&F 100 mm size stainless steel butt hinges and fixed with stainless steel screws, complete all as specified and directed by Engr-in-Charge.

S&F 200 mm long, solid in one piece stainless steel barrel tower bolts of extruded section 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 150 mm long, solid in one piece stainless steel barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm size solid in one piece stainless steel handles, D type all in 304 grade and fixed in stainless steel screwsall as directed complete all as specified and directed by Engr-in-Charge.

S&F 125mm size solid in one piece stainless steel handles, D type all in 304 grade and fixed in stainless steel screws all as directed complete all as specified and directed by Engr-in-Charge.

S&F magnet catcher for cub board with brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F 250mm long stainless steel sliding door bolts 204 grade, hasp and staple type with bright bolt not less than 16mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and complete all as specified as directed.

S&F floor door stopper of stainless steel double legged and tongue, 304 grade anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 50mm complete all as specified as directed.

S & F in repair 300 mm mild steel, ordinary rat tail rod pattern spring welded to steel/fixed to wooden door frame including roller and roller plate complete all as specified as directed.

Taking up or down steel tubing and connections with all fittings for 15 mm bore GI tubing complete all as specified as directed.

Taking up or down steel tubing and connections with all fittings for 20 mm bore GI tubing complete all as specified as directed.

M&L cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing etc and making good cutting not exc 10cm girth complete all as specified as directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing complete all as specified as directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing complete all as specified as directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 25 mm bore GI tubing complete all as specified as directed.

Refixing of old steel tubing 15mm bore, in new or old position with all new fittings to floor, wall or ceiling including cleaning old tubing as directed by Engr-in-charge (Note: Old steel tubing retrived from taking down shall be reused)

Refixing of old steel tubing 20mm bore, in new or old position with all new fittings to floor, wall or ceiling including cleaning old tubing as directed by Engr-in-charge (Note: Old steel tubing retrived from taking down shall be reused)

Supply and fixing PVC connection 15 mm dia 450 mm long with PTMT nuts at both ends complete all as specified as directed.

S&F in repair sink with drainage board, overall size 915mm x 460mm bowl size 410mm x330mmx 160mm, made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste fittings / coupling including 32 mm waste pipe over and incl beding in cement mortar to dwarf wall or including fixing cantiliver brackets and connecting unoin to pipe complete all as directed

S&F in repair sink , overall size 495mm x 420mm bowl size 410mm x330mmx 160mm, made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste fittings / coupling including 32 mm waste pipe over and incl beding in cement mortar to dwarf wall or including fixing cantiliver brackets and connecting unoin to pipe complete all as directed

S&F in repair viterous china squatting pan (orissa pattern) long pan size 580x440mm white with integral footrest with cast iron spun 600 mm long 'P' trap fixed with epoxy mortar (Asian/Berger), set in cement concrete type B-1 (1:2:4) complete (excluding flushing cistern and flush pipe) complete all as specified and directed by Engr-in-charge

S&F in repairs vitreous china wash down water closet pan (Padestal pattern) white incl plastic seat cover white, closed pattern with flat bottom with mild steel chromium plated hinging device, fixing bolts, jointing to flushing cistern and flush pipe antisyphonage pipe complete all as specified and directed. Make:- Hindware Cat No 20044/ Jaquar Cat No. ECS-WHT-555N

S&F in repairs plastic seat cover white, closed pattern with flat bottom with mild steel chromium plated hinging device for vitreous china wash down water closet pan (Padestal pattern) complete all as specified and directed. Make:- Hindware/ Jaquar

S&F in repairs CP jet spray with one metre PVC pipe complete all as specified and directed

S&F in repair 08 Litr Dual capacity PVC low level flushing cistern including PVC syphon and float valve including PVC flushing bend 600 mm long and fixing with WC complete complete all as specified and directed by Engr-in-charge (Make commander/Cera/Hindware/pearl).

S&F in repair vitreous china wash hand basin, white flat back, size 440x550mm excluding taps but including waste pipe, CP waste fittings 32mm size long shank,brass and MS brackets all as specified and directed by Engr-in-charge Make: Make :Jaquar FNS-WHT-40801 or equvilant of Hindware /Parryware FNS-WHT-40801

S&F in repair vitreous china wash hand basin, oval type counter top, white, excluding taps but including waste pipe, CP waste fittings 32mm size long shank, brass all as specified and directed by Engr-in-charge. Make- Jaquar FLS-WHT-5601 or equvilant of Hindware /Parryware

S&F in repair 75mm dia UPVC (SWR) pipes 4kgf/cm2 single socketed in any length jointed with rubber ring joints and adhesive fixed to wall with PVC clamps, complete all as specified and directed.

S&F in repair 110mm dia UPVC (SWR) pipes 4kgf/cm2 single socketed in any length jointed with rubber ring joints and adhesive fixed to wall with PVC clamps, complete all as specified and directed.

S&F in repair 75mm dia UPVC (SWR) pipes 4kgf/cm2 single socketed in any length jointed with rubber ring joints and adhesive laid in trenches or in floors complete all as specified and directed.

S&F in repair 110mm dia UPVC (SWR) pipes 4kgf/cm2 single socketed in any length jointed with rubber ring joints and adhesive laid in trenches or in floors complete all as specified and directed.

S&F in repair 150mm dia UPVC (SWR) pipes 4kgf/cm2 single socketed in any length jointed with rubber ring joints and adhesivelaid in trenches or in floors complete all as specified and directed.

S&F in repair UPC (SWR) Bend, 'T' with oval access door, jointed with adhesive for 75 mm bore pipes complete all as specified and directed.

S&F in repair UPC (SWR) bend 'T', with oval access door, jointed with adhesive for 110 mm bore pipes complete all as specified and directed.

S&F in repairs PVC tank lid/cover threaded with frame fixed with the existing water storage tank (cylindrical) for 500/1000 ltrs capacity tanks, complete all as specified and directed by Engr-in-charge

S&F in repair pillar taps, brass, with capston heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : Jaquar Cat part No. KUP-35001PM / Hindware Cat Part No:F370001 / Parryware Cat Pat No.T4302A2

S&F in repair CP wall mixer (3 in 1) with telephonic shower complete all as specified and directed. Make: Jaquar CON 281 KN,HSH 1929 & OHS 1989 / Marc ES547A & ES 531,ES 549, ES 536 or equvilant of Hindware

S&F in repair CP central hole basin mixer all as specified and directed. Make- Jaquar SOL-6001B/Hindware F450009/Parryware Cat Pat No.G0665A1

S&F in repair CP sink mixer swinging spout all as specified and directed. Make- Prayag EVIAN 8755 or equvilant of Hindware/Jaquar

S&F in repair brass chromium plated ovehead shower with shower arm complete all as specified and directed. Make : - Parryware Cat Part No T9985A1(Shower) & T-9999A1(Arm)/Hindware Cat Part No F160054 (Shower) & F190016(Arm)/Jaquar Cat Part No OHS 1999 (Shower) & SHA479L300 (Arm).

S&F in repair concealed stop cock, brass, with capston heads, fancy type chromium plated, screwed down high pressure with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make :Jaquar/Hindware/Parryware

S&F in repair angle stop cock, brass, with capston heads, fancy type chromium plated, screwed down high pressure with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : - Jaquar Cat Part No FON-40053 / Hindware Cat Part No F160017 / Prayag 9410

S&F in repair 15mm bore Bib taps short body, cast copper alloy fancy type chromium plated with, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : - Jaquar ALI-85037/Hindware F-370004/Parryware

S&F in repair 15mm bore bib taps Two way, cast copper alloy fancy type chromium plated with, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : - Parryware G0334A1 or equivalent of Jaquar /Hindware

S&F in repair 15mm bore angle valve Two way, cast copper alloy fancy type chromium plated with, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : - Parryware G4643A1 or equivalent of Jaquar /Hindware

S&F Health Faucet with 1 mtr metalic expandable tube & hook complete all as specified and directed. Make : Jaquar ALE ESS 585/ Parryware T 9941A1

S&F in repair soap dish, brass, chromium plated,100X100X60mm, fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed. Make : Jaquar CAN 1131 N or equivalent of Hindware/Parryware

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf with chromium plated guard and railling size 500x125mm (with brass bracket) complete all as specified and directed. Make : Jaquar AKP 35771P or equivalent of Hindware/Parryware

S&F in repair stainless plate rack of size 900mmx750mmx200mm made out of 1 mm thick stainless steel sheet 304 grade complete all as specified and as directed. Make : Prayag/Blue star / Slivershine.

S & F in repair PTMTgrating square 150 mm size complete all as specified. Make : Prayag Cat No. 115 or equvilant

S&F in repair Stainless steel cockroach trap square of size (101X101 mm) complete all as specified and directed. Make : Prayag Cat No. FT 21 or equvilant

S&F in repair Stainless steel cockroach trap square of size (101X101 mm) complete all as specified and directed. Make : Prayag Cat No. FT 23 or equvilant

S&F in repair brass chromium plated towel rack 60 cm long fixed complete all as specified and directed. Make : Jaquar AKP 35781PS or equivalent of Hindware/Parryware

Cleaning of existing PVC/RCC water storage tank with vaccum cleaner machine exc 250 to 500 ltrs capacity with liquid bleach and dry with and apply on coat of anti bacterial spray as directed by Engr-in-charge. Date of cleaning to and CA No to be painted on water storage tank with stencil in black/ white synthetic enamel paint all as directed by Engr-in-Charge.

Cleaning of existing PVC/RCC water storage tank with vaccum cleaner machine exc 1000 ltrs capacity with liquid bleach and dry with and apply on coat of anti bacterial spray as directed by Engr-in-charge. Date of cleaning to and CA No to be painted on water storage tank with stencil in black/ white synthetic enamel paint all as directed by Engr-in-Charge.

S&F rotational moulded polyethylene water storage tanks 500 Ltrs capacity three layered, externally white (cylindrical vertical with closed top) hoisted and fixed in position including PTMT ball valve 20mm bore with polythelene float including dismantling of existing unserviceable tank and removing from site complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 1000 Ltrs capacity three layered, externally white (cylindrical vertical with closed top) hoisted and fixed in position including PTMT ball valve 20mm bore with polythelene float including dismantling of existing unserviceable tank and removing from site complete all as specified and directed.

S&F 75mm dia out let CI spun cast floor trap with grating including jointing to waste pipe fixed with solvent cement and set in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr-in-charge

S & F in repairs 20 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

S & F in repairs ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210 gms) complete.

S&F in repair of Aluminium body door cill at bottom rail of door to stop entry of insect inside the room complete all as specified and as directed.

S & F in repair acreylic glass corner shelf with CP brass railing size not less than 300 mm long and fix to wall with rawl plug and CP screws complete all as specified and directed. Make : Jaquar/Hindware/Parryware

S&F powder coated aluminium window/ventilator fixed type half glazed and half gauged with and including hardware fittings, glazing, wire gauge, rubber packing, aluminium beading etc. as specified below including taking down old window/ventilator and making good of wall surface to match with existing surface complete all as specified and directed : - Frame : 44.5 x 44.5 mm x 1.80 mm thick Middle rail : 44.5 x 44.5 mm x 1.80 mm thick Glazing: 5 mm thick frosted glass fixed with rubber gasket and aluminium beading. Wire gauge: stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm fixed with aluminium beading.

S&F in repairs powder coated aluminium door with frame and shutter with glazing, rubber gasket, aluminium beading, glazing clips, mortice lock, aluminium stopper cleat, iron mongary etc. fabricated with following aluminium sections and other accessories: Frame : 100 x 44 x 1.20 mm thick fixed with rawal plugs Middle lock rail: 85 x 44 x 1.20 mm thick Bottom rail : 150 x 44 x 1.20 mm thick Top rail & Style: 85 x 44 x 1.20 mm thick Glazing: 4.8 mm thick retro reflective glass Aluminium glazing beading: 0.70 mm thick Aluminium handle 'D' type: 150 mm long Aluminium tower bolt : 200 mm long 9.9 mm dia shoot Mortice lock – Brass 100 mm 4 lever Hinges: Stainless steel 100 mm size Aluminium stopper cleat Note :- (i) Making good of wall surface matching to existing surface complete all as specified and directed.

S&F in repair aluminium door closer hydraulically regulated designation No. 1 universal type suitable for door shutters 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified & directed.

Dismantling asbestos cement sheet and ridges (corrugated, semi corrugated) and ridges in roof covering etc.

M&L for 6 mm thick asbestos cement corrugated or semi corrugated sheets in roof fixed with 'L' type or J type or cranked hook bolts complete.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directe by the Engr-in-Charge.

S&F Pre painted galvalume aluminium zinc coating GI based steel sheet ridge 0.50 mm thick of an colour having tensile strength of 550 Mpa made to profile of roof sheet, fixed with self tapping screws as specified all directed by the Engr-in-Charge.

S&F in repairs tiled false ceiling of Designer tile Ivory painted (High PressureSteam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of

All as per item No 152.00 (Contd/--)...1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 3mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, all complete at all heights including taking down existing false ceiling of ant type as per direction of Engineer-in-Charge.

S&F structural steel for roof trusses (framed) , purlins, crane gantries, rails and fastenings and heavy bracket framing (Pipes, Beam, Tee, Angle, Channel or Flat sections) including distance pieces, cleats etc.complete all as specified and directed by Engr-in-charge including dismantling of existing old sections complete.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips (TMT)

M&L for TMT bars 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) (1:1½:3) type A1 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. (Note :- Reinforcement & formwork shall be measured and paid for separately)

M&L for reinforced cement concrete (nominal mix) (1:1½:3) type A1 (using 20mm graded stone aggregate) as in beams, cantilevers, lintel, chajja and the like, complete all as specified and directed. (Note :- Reinforcement & formwork shall be measured and paid for separately)

M&L for steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete.

M&L for steel formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for finished surface complete all as specified

M&L for cutting into existing manholes for connecting new drain, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 (using 20mm graded complete) smooth finished and reforming benching as required complete (Internal dia of pipe 150mm).

Excavation in post holes (or similar holes) each n.exc 0.5 cum in soft/loose soil, getting out, and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specified and directed. (PCC for embedding the post shall be paid seperately)

S&F mild steel work such as in angle iron, flat iron fillets etc for posts, horns for fixing of barbed wire, securing wire mesh etc. including all necessary cuttings, drilling, bolting or riveting etc and including 10mm MS bars as in tie bars fixed to fencing posts including necessary welding where required, as per site requirement and other similar works complete mild steel, conforming to Fe-290 Gde E-165

S&F Mild steel flat iron for securing of chain link fencing including fabrication i.e. cutting, drilling holes, welding etc..complete all as specified and directed.

Mild steel bars round bars 10 mm dia cut to length, bent to shape required as in chain link fencing complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 15cm but not.exc 22.5 cm long,diameter of neck n exc12 mm complete all as specified and directed.

Fixing only Chain link fencing including line wires, any mesh size and type to any type of standards rails straining bolts etc including provision of binding wire complete all as specified and directed by Engineer-in-Charge.

Supply only Chain link fencing mesh size 100mm x 100mm, dia of wire 3.15mm as approved by Engineer-in-Charge.

Provn of 25 users septic tanks including excavation and earthwork in any type of soil , PPC foundation, brick work, RCC cover slab, precast RCC man hole cover with angle iron frame vent shaft and sludge chambers complete all as shown on TD drawing, specified and directed.

M&L for construction of soakage well, internal dia 1.80M dia & overall depth 4.50M including excavation and earthwork in any type of soil complete all as shown on TD drawing, specified and directed.

M&L for taking out existing plaster cleaning the surface and applying plaster 15m thick on roof surfaces CM 1:4 and finishing the surface even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

Supply only liquid water proofing compound. Make: Fosroc/ Sika/

Taking out existing roof treatment completely upto PCC / RCC surface and M&L for water proofing treatment on roof slab including picking, sweeping clean and washing down with water to remove dust & providing water proofing treatment described as under:- (a) Surface preparation and treating of construction joints, filling of honey combs with polymer modified mortar (Cement: Sand : smart care multipurpose polymer of Asian Paints or equivalent product of Thermax/ Berger )

All as per Item No 172.00( contd/--).... (b) Cleaning the surface and applying (Resin & Hardner) smart care Epoxy Primer 2k of Make Asian paints or equivalent product of Thermax/ Berger ) on the cleaned surface for bonding of PU magnum with the existing concrete surface. (c) Supplying, providing and applying waterproofing treatment to Terrace area with Asian Paints Smart care PU magnum, single component highly elastomeric seamless cold applied modified PU coating or equivalent product of Thermax/ Berger) including all necessary surface preparation, coving using smart care multipurpose polymer, water pond test, etc. complete as per manufacture's specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have dual combination of 250% elongation . Execution to be done with authorised applicator of the manufacturer. Work will be executed in smart assurance system.

Cleaning of man holes of any depth and size including clearing the mouth of outlet/inlet pipes, by taking out accumulated soil, sludge etc mechanically and removal out of MD land and refixing manhole cover all as directed by Engr-in-charge.

M&L for dewatering and desludging of septic tank / soakage well of any size and depth by mechanical pumping by plugging inlet as requried, including effluent, solids and sludge out of MD land includind removing the manhole covers and reinstating to its original postion complete all as specified and directed by Engr-In Charge. (Note: A particular septic tank / soakage well which is undertaken once for cleaning and paid for shall be kept functional for entire contract period and no extra payment for repitetive cleaning if requred shall be made)

Pumping out sewage water from the man holes / septic tank / soakage well at different locations by means of sewage tanker fitted with pump (5000 ltr capacity) and disposing off out of MD land as directed by Engr-in-charge .

Excavation in trenches in any type of soil not exceeding 1.5M wide and not exceeding 1.5M in depth for sewage line, manhole etc not exceeding 10 sqm on plan and getting out in any type of soil complete.

Dismantling and taking out from trenches salt glazed stone ware / RCC pipes and fittings 150mm bore including PCC benching and haunching complete all as specified and directed. (Excavation shall be measured and paid for seperately)

Dismantling and taking out from trenches salt glazed stone ware / RCC pipes and fittings 200mm bore including PCC benching and haunching complete all as specified and directed. (Excavation shall be measured and paid for seperately)

Supplying, laying, jointing and testing salt glazed stone ware drain pipe 150 mm Internal dia, grade ‘A’ confirming to IS–651–1980 laid in trenches and jointed in cement mortar 1:1 complete

Supplying, laying, jointing and testing salt glazed stone ware drain pipe 200 mm Internal dia, grade ‘A’ confirming to IS–651–1980 laid in trenches and jointed in cement mortar 1:1 complete

M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm bore pipe complete all as specified and directed.

Returning, filling in, including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete.

Removing excavated material to a distance n exc 50m and deposited where directed at a level n. exc 1.5M above the starting point complete.

M&L for 60 mm thick vibromatic reinforced precast cement concrete 1:1:2 (using 20mm graded stone aggregate) with 2mm thick mild steel CR sheet around painted with 2 coats of bituminous paint , as in man hole cover slabs finish fair even and smooth without using extra cement ( Top surface will be chequred finish) including necessary form work, 100 mm long handle of 12mm dia round bar counter sunk by 25mm welded to reinforcement complete all as specified and directed by Engr-in-charge (Note : CA No and date will be engraved on covers. Reinforcement shall be measured and paid separately. Curing will carried out with ponding method)

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in and including concealed PVC conduit medium duty 20 mm dia or higher and heavy grade conduit fittings and heavy duty accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.6mm thick for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of following. Make of PVC Wire: Havells/KEI/Finolex/L&T. (Note: The wiring to be done as per IE rule and maintain colour code accordingly).

(a) One light point point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

All as per Item No 187.00 here in above but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in existing PVC / Steel, concealed and existing MS boxes but including new 3 mm thick plastic laminated sheet as top cover, mounting of switches, sockets, fan regulator etc one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of following Make of PVC Wire: Havells/KEI/Finolex/L&T. Note: The wiring to be done as per IE rule and maintain colour code accordingly

(a) One light point point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) One light point controlled by two way switch

All as per Item No 189.00 here in above but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete.

S&F moduler switch piano flush, button type 6 Amp SP one module one way complete all as specified Make : Legrand model Lyncus 6772.00 eqvt in L&T model entice/ Havells model Murano.

S&F moduler switch piano flush, button type 6 Amp SP one module two way complete all as specified Make : Legrand model Lyncus XXX eqvt in L&T model entice/ Havells model Murano.

S&F moduler switch piano flush button type 16 Amps SP one module one way complete all as specified Make : Legrand model Lyncus Cat No 6772.09 eqvt in L&T model entice/ Havells model Murano.

S&F moduler socket outlet multipurpose 5 Pin 6 Amp two module complete all as specified & directed. Make : Legrand model Lyncus Cat No 6772.28 eqvt in L&T model entice/ Havells model Murano.

S&F moduler socket outlet two in one three pin 6 Amp and 16 Amp two module flush type complete al as specified.Make : Legrand model Lyncus Cat No 6772.30 eqvt in L&T model entice/ Havells model Murano.

S&F moduler bell push 6 Amp one module one way complete all as specified. : Make : Legrand model Lyncus Cat No 6772.20 eqvt in L&T model entice/ Havells model Murano.

S&F 4 step modular electronic fan regulator step type 2 module 120 watts 360 degree.Make : Legrand model Lyncus model 6772 41 eqvt in L&T model entice/ Havells model Murano.

Supply and fixing in repairs of modular metal flush box with and incl decorative polycarbonate frame for fixing of switches and cover plate white or coloured as decided by GE suitable for 12 modules 3 row and blanking plate if any required for spare module complete incl gouting boxes flush to wall and taking out old u/s complete. Make Legrand Lyncus/Havells/L&T

All as per item No 198.00 here in above but 8 module single or double row as per site requirement complete all as directed by Engr incharge. Make Legrand Lyncus/Havells/L&T

All as per item No 198.00 here in above but 6 module complete Make Legrand Lyncus/Havells/L&T

All as per item No 198.00 here in above but 3 module complete Make Legrand Lyncus/Havells/L&T

All as per item No 198.00 here in above but 1 or 2 module complete. Make Legrand Lyncus/Havells/L&T

S&F ding dong bell AC 230 V single pole complete all as specified and directed .

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 250 V AC.

S&F lamp holder, pvc/polycarbonate type with back plate suitable for batten fittings including 3/5 W LED retrofit lamp complete all as specified & directed.

S&F lamp holder, pvc/polycarbonate type with back plate suitable for batten fittings including 7 W LED retrofit lamp complete all as specified & directed.

S&F lamp holder, pvc/polycarbonate type with back plate suitable for batten fittings including 10/14 W LED retrofit lamp complete all as specified & directed.

M&L for sub main wiring with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 4 Sqmm (nominal area) and one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 4 Sq mm as earth wire upto common earth and connected to earth dolly drawing through existing PVC/steel conduit complete incl taking out old unserviceable submain all as specified & directed. Make: Havells/Finolex/L&T

S&F in repairs Busbar chamber of size 600x315x214 mm or higher size with PVC hinged lid, polycarbonate type (shock proof, rust free, corrosion free, acid and chemical resistant, fire retardant, having high impact, made of halogen and silica free recyclable material), UV resistant, having high grade gasket made of polyurethane, flame retardant, suitable for and mounting arrangement for fixing of MCCB 4 pole, 160 Amps 25 KA (Icu=100%Ics) 415 Volt,50 Hz, duly connected with and incl 04 Nos of copper Busbar 300 Amps fixed on epoxy insulators, gun metal cable gland of 25 Sqmm 01 No and PVC coupler for sub main wires 04 Nos completecomplete all as directed at site by Engr in charge complete. Note:- Only MCCB shall be measured and paid for seperately all other items incl connection from MCCB to busbar with suitable size copper wire incl thimble, bottle lugs etc are incl in item rate. Make:- Hensel cat No Mi 9410 or ABB/BCH/Schneider

S&F in repairs Distribution board Vertical type TPN 4 Way double door, suitable for MCCB 63/100 Amps MCCB as incoming and MCBs for outgoing factory made, IS: 13032 marked with valid CM/L No fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and baked at high temperature, painted in seven tank process. The DBs shall be of IP 43 protection incl taking out old u/s complete. Note:- DB and MCCB/MCB shall be of same make Make:- Legrand/Hager/L&T AU

S&F in repairs Distribution board SPN 8 Way double door, for mounting MCBs isolator, ELCBs etc factory made, IS: 13032 marked with valid CM/L No fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and baked at high temperature, painted in seven tank process. The DBs shall be of IP 43 protection. Note:- DB and MCCB/MCB shall be of same make Make:- Legrand/Hager/L&T AU

Supply and fixing of MCCB 100 Amps FP 415 Volts having breaking capacity 15 KA with and incl spreader link kit complete suitable for fixing as incoming in polycarbonate busbar complete all as specified and directed.

S & F , MCB SP 6 to 32 Amp, 240 Volts, 'B' curve having breaking capacity 10 KA, air flow channels and ON/OFF indication.

S & F , Isolator SPN 40 to 63 Amps, 240 Volts having braking capacity 10 KA.

Material and labour for CPRI approved chemical earthing complete with GI pipe electrode 50 mm dia, 2 Mtr long with terminal size 50x6 mm buried directly in ground not less than 2.25 m deep below normal ground level connected with and incl galvanized wire 4 mm earth lead upto DB by means of nuts bolts check nuts GI washers etc duly protected by galvanized iron pipe 15 mm bore (light grade) including PVC accesse well and cover and gel type back fill compound necessary earth work in soft/loose soil complete all as directed by Engr in charge including testing on completion all as specified and directed. incl demolition to existing one complete. Make; SNE/OBO/ENNOVE

S&F in repairs LED tube light fitting batten type with extruded alluminium body and polycarbonate deffuser all in one single phase 22/20 W with lamp 6500/4000 K complete pre-wired all accessories. Make Philips Smart Bright or Crompton Cute linea/WIPRO TRMLED

S&F in repairs LED light fitting 1x10 w bulk head fitting complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size Make:WIPRO CAT PART NO-LW07-141-XXX-57XXor equivelent , HAVELLS/CROMPTON

S&F in repairs wall/ceiling mounted decorative downlighter with 15 watt retrofit LED lamp with engineering plastic housing complete all as directed by Engineer-in-charge. Make Havells Cat No Crown or equilent in Philips/Wipro

S&F in repairs decorative wall mounting made out of polycarbonated suitable for and incl retrofit 15 watts retrofit LED bulb complete all as specified. Make Havell Cat No City 1 New or equilent in Philips/Wipro

S&F in repairs, connecting and testing of 35 watt LED building security light luminaries with min 10 KV surge protector die cast alluminium housing LDR sensor for automatic operation complete suitable for and incl bracket 32 mm GI pipe bend to shape incl clamp fastner, bolts, nuts & washers of min 1.2 Mtr incl grouting etc and 3 core 1 sqmm PVC insulated cable from ceiling rose to light fitting complete all as specified Make:- Crompton/Philips/OSRAM

S&F in repairs mirror light decorative compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size . Make Havells Cat No Edgelite or equilent in Philips/Wipro

S&F in replacement Sheet metal enclosure SPN with a two pin and earth plug and socket complete with one 20 amp single pole MCB complete all as specrified & directed

S&F in replacement tamper proof electronic single phase whole currrent energy meter (LCD display) 10 Amp to 60 Amp, 240 volt class 1.00 and AC supply including cable connection, proper sealing with barcode with PVC seal. The meter shall comply with the latest version of IS-13779 with at least 2 anti tamper LED indications of line load reversal and earth loading indication including electrical connection with existing system and sealing properly including push fit type transparent meter box . The meter shall work satisfactory with guaranteed accuracy as per limit of IS: 13779. The meter shall be fixed on existing steel boxes on wall complete all as specified and directed. Make:- Secure I credit 350/L&T/BHEL (Note:- Old unserviceable meter will be deposited to E/M store yard)

Ram Naresh Singh Sikarwar

M/S C S AITHANI

RASHI CONSTRUCTIONS