Loading
Loading…
Loading…
Tender Value
₹3.5 Cr
EMD Value
₹7.1 L
Closing Date
13 Oct 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
SRDSTECSIG
14 conditions · 2 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Form-2, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Technical Eligibility Criteria: The Tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- Any work in connection with Signaling Installation and which includes relay wiring and laying & termination of cables. OR Any Signaling work involving Supply, installation, testing & commissioning of AFTC/DAC/MSDAC/UFSBI/BPAC system. Note 1: Tenderer may be required to submit the schedule of those works, Completion/Performance Certificates of which have been submitted by him/her in support of 30 / 40 / 60% (as the case may be) criterion of similar nature of work. Note 2:a. Submission of 'Undertaking by the tenderer' that the equipment for El or Axle Counter or AFTC or UFSBI shall be procured from RDSO approved sources and installation, testing and commissioning of El or Axle Counter or AFTC or UFSBI shall also be got done from the same source including after sales support required during the warranty period. AND b. After the award of the contract, MOU with RDSO approved source covering supply of equipment for Axle Counter or AFTC or UFSBI. Installation, testing & commissioning of Axle Counter or AFTC or UFSBI by the same RDSO approved source including after sales support required during the warranty period before supply of equipments is undertaken. AND For Electronic Interlocking (EI) equipments, this should be read as 'The successful bidder shall submit an undertaking from RDSO approved EI OEM, before the supply of material, to confirm compliance with extent RDSO guidelines and to meet contract specific requirements'. Rest of the content remains unchanged.
14 conditions · 9 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
PAN Number to be attached.
Registered Office Address with contact no.
Detail of Bid Security paid, through only payment modes available on IREPS portal like net banking, debit card, credit card etc.
Mandatory undertaking regarding Employment/Partnership of Retired Railway Employees as per Clause No. 12 of Chapter-I as per Annexure- E.
Mandatory certificate to be submitted by tenderer along with tender documents as per Annexure- A.
GST Number to be attached.
Mandatory Power of Attorney to be submitted by tenderer along with tender documents as per Annexure- B.
MOA & AOA, Resolution of Board and POA, Sole Proprietorship, Notarized partnership deed with POA and latest certificate of registration with Registrar of the firms must be attached. Year of Formation / Incorporation. (As per Clause-10 of Tender Document
Upload duly filled and signed Cover Letter (Tender Form 1)
Mandatory Document Tenderer uploaded Annexure-A (1) {This certificate is to be given by attorney/authorized signatory/each member of Partnership firm/Joint Venture (JV)/Hindu Undivided Family (HUF)/Limited Liability Partnership (LLP) etc.)}of tender documents.
An undertaking by the tenderer shall be provide at the time of tender submission that the equipment shall be procured from RDSO/TEC/OEM covering supply, installation, testing, commissioning of system including after sales support required during the warranty period.
Provision of Automatic Media changeover redundant to data transmission on Quad/OFC for UFSBI system over Delhi Division.
558-Sig-16-M-Tender-1482~NR
558-Sig-16-M-Tender-1482
Open
Works - General
12 Months
Delhi, Delhi
₹0
₹7.1 L
21 Sept 2026
21 Sept 2026
29 Sept 2026
43 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 3,53,25,057.04 | ||
| — | 74.00 | — | — | ||
| Supply & installation of automatic media changeover of modem working on redundant channel data transmission on OFC/QUAD. Inspection :RITES for supply portion, execution: Site engineer. | — | — | — | 29,54,048.18 | |
| — | 74.00 | — | — | ||
| Supply & installation of Modem compatible with existing UFSBI system to work on backup media (either VF-Channel of OFC P/MIUX or 2 MBPS E1 channel from STM or direct single Mode I - core optic fibre cable upto 30 Kms distance) The required type must be mentioned while ordering. Inspection :RITES for supply portion. | — | — | — | 46,96,737.82 | |
| — | 20.00 | — | — | ||
| Supply ,installation ,testing and commissioning of Automatic change over device for DAC / UFSBI V.21 / V.23 to Optical fibre , STM(E1) , standard 19"rack mountable device consisting of two E1 port supporting 120 Ohms interface; dual optical ports with (1+1) hot stand by (dual core path and single core path) 20 Kms driving distance and four V.21 /V.23 (E&M) 2W/4W interfaces with auto change over mechanism to Quad ports 2W/4W ; each port configurable as 2W or 4W no restriction in configuration ; unit to support Potential free contacts four numbers can be linked with data logger / RTU for E1 Status , Quad Status & Power Supply status ; Unit support front panel ressetable audio able buzzer in case of main link fails (optical or E1) ; Unit to support power OFF fail safe mechanism when the unit is switched OFF the inputs is by passed to the Quad cable automatically unit supports; Unit supports front panel LED indicators for Quad health status ; E1 dual ;Optical dual path ; Dual DC power supply 18VDC to 72VDC range ; Make : TeamEngg /Cygnus/ Lantana /Waves / FABIO1CX - 4P or similar .(Inspection Agency: RITES) | — | — | — | 35,72,284.8 | |
| — | 50.00 | — | — | ||
| Supply of E1 extender with 24V/48 V DC operating supply Line type 2 wire or 4 wire twisted copper wire • Bandwidth 64 kpbs to 2048 kpbs • Operating mode 2 wire or 4 wire selectable • Connector RJ45 G SHDSL Line interface • Line Interface 135 ohms • Connector RJ45 G703 Interface • Local Loopback, Digital Loop back and remote loopback as per ITU Standard • Power supply 24V on Data logger side, -48v on STM Side • Temp range to suite data logger specs to be certified by OEM • Make-Cygnus/Anda/Team Engineer/RAD/Efftronics. Inspection: RITES. | — | — | — | 12,25,480 | |
| — | 50.00 | — | — | ||
| Installation, testing and commissioning of E1 Extenders. Inspection: Site Engineer. | — | — | — | 75,000 | |
| — | 25.00 | — | — | ||
| Supply of VF Tapping & Termination Transformers 2T/1120:470 Ohm as per IRSTC- 22/76 with Amd-1 or latest amendments (round type). Inspection: Consignee. | — | — | — | 57,240.75 | |
| — | 5000.00 | — | — | ||
| [Supply of CAT-6 UTP Cable (23 AWG). It Shall comply to TEC GR No. TEC/GR/SLC - 01/02.AUG 05 (TEC Standard Number: TEC 52010:2005) with latest 8 lamendments, Version. Inspection by Consignee. | — | — | — | 1,13,250 | |
| — | 74.00 | — | — | ||
| Supply, Installation, testing and commissioning of 48 Fiber (SC/APCSC/ APC) FDMS including splicing of OFC and termination of all fibres using pig tail cable of standard size ( All materials including pig tails (5 meter each) to be supplied by the contractor, this also includes arrangement & fixing of suitable metal box fixable in wall for spare OFC coil).Inspection: RITES for supply portion, Execution: Site Engineer. | — | — | — | 22,37,424.78 | |
| — | 74.00 | — | — | ||
| Supply and installation of optical fibre cable joint enclosure as per TEC spec no. GR/OJC02/01/March 99 with latest amendment and splicing of optical fiber cables (24/48 fibers and testing) . This includes provision of joint pit (RCC/Prefabricated) as detailed in the Technical specifications and as advised by Engineer at site. Inspection : RITES for supply portion, Execution: Site Engineer. | — | — | — | 13,49,688.22 | |
| — | 200.00 | — | — | ||
| Supply of OFC jumper (Patch card) 10mtr. long with FC/PC and SC or suitable connector at both end as per IRS:TC-81/2000 with latest amendment.Note: Item supplied must be suitable with FMS. (Inspection. Consignee) | — | — | — | 1,25,440 | |
| — | 74.00 | — | — | ||
| Alteration in existing data logger wiring and revalidation of inputs as per site requirement. Work includes supply of wiring material , shifting/re fixing of DATA LOGGER (if required) Inspection: Consignee | — | — | — | 13,53,291.28 | |
| — | 500.00 | — | — | ||
| Supply and installation of push button switch of Make L&T or SIEMENS or better with paralleling of NO/NC contact in block panel of UFSBI of Deltron Make Equipments and systems as per RDSO Specification No. IRS:S:105/1012 ver.1.0. (Black). Inspection: RITES for supply portion, Execution: Site Engineer. | — | — | — | 16,22,500 | |
| — | 160.00 | — | — | ||
| Supply of Surge protection module suitable for Deltron Equipment of UFSBI as per RDSO Spn.No.105/2012 (Ver. 0) or latest compatible to use in existing UFSBI with Block Panel with Din Rail mounting arrangement comprising of - (a) Class C type II SPD for 24V DC (19-31 VDC) power supply line to UFSBI for differential and common mode surge- 1 No. (b) Class D/Type III SPD for 24 V DC (19 -31 VDC) power supply line to UFSBI for differential surge- 1 No. (c) Class D/Type III SPD for communication line (2 wire Tx & 2 wire Rx) to UFSBI for differential surge. Inspection: RITES. | — | — | — | 49,08,800 | |
| — | 16.00 | — | — | ||
| Supply of Non-Vital MUX, having 32 inputs suitable for placing in each Hut or Station (alongside UFSBI MUX cabinets) towards I/O Exchange and Display arrangements at end stations on dark OFC incorporating Cloud Interfacing features. One such System shall be placed for each of Up & Dn line UFSBI rack. These modules will be used for section wise display of Automatic Signal Aspects, Tracks, LC Gates Staus, etc, at end Station on LED TV/ Industrial PC with Monitor. The Non-Vital MUX for display of Auto Section must have compact, atleast SIL-2 compliant CPU and safe IP based communication between nodes on Ethernet/OFC Media. Inspection: RITES. | — | — | — | 49,93,629.6 | |
| — | 16.00 | — | — | ||
| Supply of Smart Industrial Grade LED TV Display Monitor/ LED TV 55"" (Industrial grade capable of working 24x7) to display train information being displayed on Multiline Display Board as per RDSO/SPN/TC/108/2019 (Ver.- 5.0 ). Make: Samsung /Sony/LG-55UH5J HDR 4K UHD Commercial LED TV or latest. (TO BE INSPECTED BY RITES) | — | — | — | 9,17,335.36 | |
| — | 16.00 | — | — | ||
| Installation, Testing and Commissioning of the Display arrangements at Non-Vital MUX modules at the SM's Room/Cabin of Station with drawing, as per the instructions of Rly site Engineer. Inspection: Site Engineer. | — | — | — | 6,03,121.6 | |
| — | 14.00 | — | — | ||
| Supply, Installation & Commissioning of maintenance free earth suitable kit as per RDSO Specification no. RDSO/SPN/197/2008 and Drg No.SDO/./E&B/001 dated:- 19.09.2008 and Drg No. RDSO/SDO/./E&B/002 dated:- 19.09.2008. Earthing kit consisting of earthing electrode of 17mm dia as 3m long -01 no 2 MEEB (300mmx25mmx6mm) -o1 no. 3. SEEB (150mmx25mmx6mm) -01 no 4. Earth enhancing compound - 30 kg (minimum). This includes:- Provisiion of earth connection from MEEB to S&T equipment i.e. cable sheath, apparatus case, BPAC, Axle counter, IPS, Data Logger etc. with PVC earth wire of size 25/35 sq.mm through copper lugs of suitable size PVC earth wire shall be supplied by contractor. Note: At certain locations, it may not be possible to acheive earth resistance of less than 1.0 ohm with one earth electrode /pit due to soil resistivity. In such cases, provision of loop earth consisting of more than one earth pit shall be done, for interconnection of two earth pits copper tape of size 25x2 sq.mm shall be provided by the contractor. The number of pits required shall be decided based on the resistance achieved for the earth pits already installed. The procedure mentioned above for one earth pit shall be repeated for other earth pits. The other earth so installed for the purpose of loop earthing arrangement shall be counted as seperate earth. Inspection : RDSO for supply portion, Execution: Site Engineer. | — | — | — | 3,62,220.18 | |
| — | 1.00 | — | — | ||
| Supply of OTDR as per TEC spec No. GR/TX/ OTD-01/04/Apr-10 or latest. OEM Test certificate of this item shall be provided by contractor.Inspection by RITES. | — | — | — | 3,99,401.27 | |
| — | 10.00 | — | — | ||
| Supply of Failure Analysis System (FAS) & failure analysis software, as per Technical Specifications.: Processor Intel Core i7 processor 12th generation or latest, RAM 16 GB, Minimum Storage 512 GB SSD, optical Mouse Standard Keyboard (USB) Mouse (USB Optical) DVD Drive 16X DVD+/-RW with Dual layer Optical Drive Modem: High speed 64K Modem or latest, offline UPS 1 KVA, LAN Network: Integrated 100/1000 LAN Ethernet, Wi-FI, Bluetooth Graphics Card: 2 GB or higher (make: Nvidia/Radeon or higher) OS pre-installed licensed software, Windows 11 Professional (Licensed Version) or latest (Minimum) with MS Office (Licensed Version), Display 27"" LED (Minimum) Warranty 3 years (Minimum) Make: Lenovo/HP/DELL or Superior, . Inspection: RITES | — | — | — | 17,89,478.2 | |
| — | 10.00 | — | — | ||
| Installation, testing and commissioning of Failure Analysis System (FAS) as per Technical Specifications. The specification of FAS should be got approved from the Engineer in charge before supply. Inspection: Site Engineer. | — | — | — | 3,39,002.8 | |
| — | 180.00 | — | — | ||
| Maintenance of Track Mounted Equipments like S&T fitting on turnouts including different activities during BCM/TTM/UNIMATE machine works as follows: Specially opening and refixing of DC Track circuit jumpers / Axle Counter transducers during different Engineering Works.Opening of DC Track circuit / Axle Counter transducers digging work from rail toTLJB / TMU/ Location is required to be done as per site requirement also after refixing of DC-Track circuit / Axle Counter transducers needs to be buried in proper depth. It includes drilling hole in rail as per site requirement. The team to be provided for this work should comprise of: Fitter -1 Nos., Blacksmith -1 Nos., Mason / Carpenter - 1 Nos. and Helpers - 5 Nos.also it includes any work of Electrical operated lifting barriers (EOLB) or sliding boom and earthing arrangement of Signalling gears. Any other work as per instruction of Railway Engineer. All T&P & jigs required to execute the work will be supplied by the contractor. (NOTE: THE UNIT FOR THIS ITEM MAY BE READ AS "PER DAY PER TEAM"). Inspection: Consignee. | — | — | — | 16,29,682.2 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Tender-Doc-1482.pdf
ATTACHMENT
splinstruction.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .