Routine / Corrective maintenance to Snow Cat 90HP MD pertaining to Mechanical and Hospital Sub-Division 1st Baramulla

Preventive maintenance by way of carrying out following jobs: 1.Providing & Filling of M-Oil 15W40 (12 Ltrs@380/ltr)= 4560 2.Providing and filling of Gear Oil 75W 90 (20 Ltrs@600/ltr)= 12000 3.Providing and filling of Hydraulic Oil (10W) (5 Ltrs@400/ltr)=2000 4.Providing and filling of Coolant(Antifreeze) (3 Ltrs@350/ltr)= 1050 5.Providing and filling of TQ Oil (2 Ltrs@450/ltr)= 900 6.Providing & Fitting of M-oil Filter (01 Set@ 720)= 720 7.Providing & Fitting of Diesel Filter (01 Set @1050)= 1050 8.Hydraulic oil filter = (01 No @1550)= 1550 9.Transmission oil/Strainer filter = 01 No. (01 Set @850)= 850 10.Providing & Fitting of Air Filter assy (01 Set@1900) =1900

Electrical repairs to Snow cat by means of p/f of Led fog lamps (06 no's), Wiper Arm with Blade (01 Set), Starting Relay, rear working light and replacement of damaged wiring and P/f of new Horn. The job also includes Providing and fitting of 12V emergency Siren with allied accessories including wiring, fuses and Toggle switch. Further job includes P/F of Multi-point mobile charger with C and D type cables of Reputed make.

P/F of side view mirrors on both sides of Snow Cat, complete with mounting base, brackets and all necessary fittings as per sample, complete in all respects.

Providing and fitting of high-pressure hydraulic Hose having length of 198 inches and 1/2 inches Diameter, capable of withstanding of hydraulic pressure of 3980 PSI. The hydraulic hose shall be fitted with adopters on both sides as per sample.

Modification to the fuel tanks of the snow cats by way of increasing the fuel capacity from 90ltrs to 160 lts. The Job includes providing, & fitting of 160 lts fuel tank replacing the already existing 90 ltr tank. The job includes fabrication and errection of housing frame out of MS angle/flat by way of welding along with supports to the new fuel tank wherever necessary. The job includes providing and fitting of fuel pipe line wire braided (i.e. supply and return line with all fitments appx length 15feets). The job also includes complete testing and commissioning of newly installed fuel tank. (The job is required for machines which are deployed for snow clearance operation of far-flung areas where from refilling of fuel at the designated fuel station is time consuming and un-economical).

Supply, installation, testing and commissioning (SITC) of a new genuine/OEM hydraulic pump assembly suitable for Farmtrac FT-90 (90 HP) tractor(Pump body shall be manufactured from high-grade cast iron or equivalent material with precision-machined internal components. Bearings, gears/rotors and shaft seals shall be factory assembled and tested), including dismantling and removal of the defective hydraulic pump, cleaning of the hydraulic system, inspection of suction strainer, pipes and hoses, replacement of all required seals, O-rings, gaskets and mounting hardware, installation of the new hydraulic pump, alignment and tightening as per manufacturer's specifications, topping up/replacement of hydraulic oil as required, bleeding of the hydraulic circuit, calibration of hydraulic pressure, functional testing of the hydraulic lift and remote hydraulic system, rectification of minor leaks, road/field testing, and commissioning complete in all respects. The Job also Includes complete flushing of Hydraulic system and then refilling of new Hydraulic oil conforming to OEM recommended Grade) and testing Thereof

Supply of Heavy-duty hydraulic Jack consisting of piston and cylinder arrangement for snow cat 90 Hp having specification as given blow. a) Fully closed position: Distance between centre’s of Jack pin bores on both sides = 71.5Cm b) Fully open position: Distance between centre’s of jack pinbores on both sides = 83.00Cm c) Cylinder bore diameter = 8.2 Cm d) Jack pin bore diameter = 2.30 Cm e) Diameter of piston rod = 3.35Cm

Providing of 30 Ltr HSD @96.14/ltr= 2884.2 for Testing of machine and general checkup after completion of Job.

Manufacturing and providing / fitting of Non-Skid Chains Compatible with Tyre of Size 12.2 x 24 fabricated out of EN-8 material alloy steel hardened having crossectional area 12mm x 8mm with proper/suitable locking arrangements one complete job.