New_Hostel_Building

Amount

Civil Work

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.: All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads, all lifts, all height, all depth, all floor; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. a) Concrete of M25 grade with minimum cement content of 330 kg /cum : All works upto plinth level

b) Concrete of M25 grade with minimum cement content of 330 kg /cum: All works above plinth level to all floor level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. all level, all floor. Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings) except spiral-staircases

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure including scaffolding, all floor, all height, all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure including scaffolding, all floor, all height, all level: Cement mortar 1:4 (1 cement :4 coarse sand)

CEMENT PLASTER (IN COARSE SAND): Providing and laying plaster : 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) including scaffolding, all floor, all height, all lead, all lift etc.

CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT: 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand) including scaffolding, all floor, all height, all lead, all lift etc.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge. Including grooves finish, scaffolding, all floor, all height, all lead, all lift etc.

Extra for providing and mixing water proofing material in cement per bag of plaster work in proportion recommended by the manufacturers.

Interior Paint : Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour, scaffolding, all floor, all height, all lead, all lift etc. Two coats

Wall Primer: Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. including scaffolding, all floor, all height, all lead, all lift etc.

Putty: Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Exterior Paint: Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including scaffolding, all floor, all height, all lead, all lift etc.

Exterior Paint: Finishing walls with textured exterior paint of exposed RCC look or required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm. including scaffolding, all floor, all height, all lead, all lift etc.

Supplying, diluting & Injecting chemical emulsion for Pre constructional Anti Termite Treatment With Chlorpyriphos/Lindane E.C. 20% with 1% concentration in 3 stages creating a continuous chemical barrier all-round the building including diluting in water as per manufacturer's specification conforming to IS 6313: 1981 in under & all around raft slab, beam, footings, column pits, trenches, wall trenches, backfill, plinth filling, junction of wall and floor, external perimeter of building, surrounding of pipes, over the top surface of the consolidated earth etc. for all lead and lift.. The treatment shall be carried out by specialized agency specified by the Client/ Consultant. Plinth area at ground level excluding open courts shall be measured. Treatment of soil under floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos E.C. 20% with 1% concentration

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Providing and fixing Expansion joint Capcell HD 100 Supreme & finish with PVC belt or equivalent make of 50 mm thickness of best qualtity, including cutting to required size and shape at all levels complete as directed by Engineer in charge. The works shall also including cost of primer in expansion joint and providing and laying polysulphide sealent at 1.5 kg per meter with providing backer road for expansion joints of BASF / Sika / Fosroc or equivalent make and make the joint water tightness as per direction of Engineer in charge.

Light Weight Filling in the Sunken Portion: Providing and filling the cavity of sunken portion of toilets (after application of principal waterproofing treatment to surface of sunk RCC slab) with broken AAC blocks of 25 mm to 115 mm in size with 50% of cement mortar 1:4 conforming to IS : 2645 complete as directed by the Engineer-in-charge.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish, Size of Tile 600 x 1200 mm : Equivalent to Varmora Letto steel 600x1200mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600 x 1200 mm : Equivalent to Varmora Letto steel 600x1200mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish, Size of Tile 600 x 600 mm (Toilet area flooring) Equivalent to SUNHEART ENRICH GREY (MATT) SIZE : 600 x 600

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in dedo, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x1200 mm (Toilet area dedo and skirting) Equivalent to SUNHEART KEEN BLANCO(GLOSSY) SIZE : 600 x 1200

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and mirror polishing complete with base of cementmortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and mirror polishing , antiskid groove complete.

Artificial / Granite work in wall : Providing and laying Polished Granite stone slabs 18 mm thick in risers of steps, skirting, dado, cladding and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Equivalent to Motto Saga SNP Verde Grey Finish- Glossy

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for window sills, door frame and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red (Door Frame)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for window sills, door frame and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red (Window sill)

Granite Basin Counter 600 wide: Providing & fixing two layers of wash basin counter, first layer using 25mm thick Kotastone of approved shade and second layer using approved shade and sample of 18 mm thick Mirror finish Granite, joined together with 1:4 Cement mortar bedding / approved tile adhesive , to true plane & level or to slopes, or close jointed with cement slurry with pigment of matching shade and colour and finishing with the same, including dedo 1'6", cutting kotah & tile as per required shape & size to fit Wash basin & 4" facia with moulding, nosing, chamfered front edges, fixing, disposal of debris etc. finished as per design in detail drawing and instruction of Architect/EIC.sample mock shall be approved from Architect/EIC.

Granite Pantry Platform 600 wide: Providing & fixing two layers of Pantry Platform, first layer using 25mm thick Kotastone of approved shade and second layer using approved shade and sample of 18 mm thick Mirror finish Granite, joined together with 1:4 Cement mortar bedding / approved tile adhesive , to true plane & level or to slopes, or close jointed with cement slurry with pigment of matching shade and colour and finishing with the same, including dedo 1'6", cutting kotah & tile as per required shape & size to fit sink & 4" facia with moulding, nosing, chamfered front edges, fixing, disposal of debris etc. finished as per design in detail drawing and instruction of Architect/EIC.sample mock shall be approved from Architect/EIC.

Thin Profile Glass Partition with Framless Glass Door : Providing & Fixing of STL45 ie.Single glazed modular system consist of Aluminium section of 16*45*2.5 mm thick. All sections duly powder coated with 6063-T6 grade and required accessories ie glass to glass aluminium I sections, T section & 90 degree sections & Glass packing to adjust the floor level. Ceiling profile, Floor profile and wall profile are 16 mm visible face and 45 mm wide with 12mm toughened glass , Framless glass door with necessary hardware as per approved make & insertion of Thermoplastic gasket to adhere the glass firm & airtight.The sound reduction Value is from 32 to 35 Db.With 6 mm Groove inbuilt in system to accomodate the carpet & the uneven surfaces. Accessories/Hardware: neutral cure glazed & metal silicon sealant of approved make on the periphery of the glass & wood etc. Partition ht will be measured from finish floor to false ceiling level only. The rate shall be in sq.mt for all floors and at all heights including all costs. Glass width size shall be as per sugestion by EIC. Work complete including all type of material, fittings , fixtures,Finish, safety measures , loading , unloading , transporation, all leads ,accessories, sample mockup, all floor , all levels, all heights etc complete as per detailed drawings ,specifications & instruction of Client/EIC.

Three track sliding Door : Two glass shutter +1 Mosquito shutter: Domal section : 27 x 65 mm series Supply & Fixing of Aluminium sliding door with powder coated as per by approved make & sample by architect/EIC. Frame section: 101.5 x 47.5 x 1.5 mm , Shutter section : 27 x 65 x 1.4 mm, Mosquito shutter : 27 x 65 x 1.4 mm Glass : 5 mm thick tinted grey toughened glass of saint gobain or approved make list Work including Trolley Wheel (Bearing), EPDM Gasket, Woolen In Shutter, Concealed Lock, Anti Rattling Guide, Lock Guide, handle Antilifting, Shutter Corner Clit, Shutter wing Connecter, Interlock EPDM Gasket, Interlock Guide, Anti Capillary Pad, Bush Bottom silicon all side & All Necessary Hardware etc. complete as per detailed drawings, mock sample and specifications.

Single Leaf Flush Door finish with laminate: Providing and fixing in position 40 mm thick BWP grade single leaf flush doors of approved make and finished with both side 1 mm thick VNR laminate as approved sample, Hardware system as per approved make & Sample (Hinges, Mortise lock with 3 pair key, Door stopper ) . work complete including all type of hardware, fittings , fixtures as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client. Equivalent to VNR Series Laminate.

Single Leaf Flush Door finish with laminate (Toilet door): Providing and fixing in position 40 mm thick BWP grade single leaf flush doors of approved make and finished with both side 1 mm thick VNR laminate as approved sample, Hardware system as per approved make & Sample (Hinges, cylindrical lock, Door stopper ) . work complete including all type of hardware, fittings , fixtures as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client. Equivalent to VNR Series Laminate.

Handicap Toilet Door : Providing and fixing in position 40 mm thick BWP grade single leaf flush doors of approved make and finished with both side 1 mm thick VNR laminate as approved sample, Hardware system as per approved make & Sample (Hinges, Mortise lock , Horizontal grab bar, Door stopper ) . work complete including all type of hardware, fittings , fixtures as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client. Equivalent to VNR Series Laminate.

Sliding window : (Domal series) Supply & Fixing of Aluminium sliding window with powder coated as per by approved make & sample by architect/EIC. frame section: 101.5 x 47.5 x 1.5 mm Shutter section : 27 x 65 x 1.54 mm Glass : 5 mm thick reflective glass of saint gobain or approved make list including concealed lock, albose , other necessary fixtures and fastening , PVDF rollers , EPDN gasket, silicon sealent etc. complete as per detailed drawings, mock sample and specifications.

Fix glass : (Domal 27 mm series) Supply & Fixing of Fixed glass window with powder coated as per by approved make & sample by architect/EIC. frame section: 40 x 89 x 1.5 mm Glass : 5 mm thick cleaver reflectiive glass of saint gobain or approved make list including necessary fixtures and fastening , EPDN gasket, silicon sealent etc. complete as per detailed drawings, mock sample and specifications.

Ventilation with provision of Exhaust fan : Supply & Fixing of Ventilation with exhaust fan with powder coated as per by approved make & sample by architect/EIC. frame section: 45 x 45x 1.5 mm Glass : 5 mm thick Frosted toughened glass of saint gobain or approved make list including necessary fixtures and fastening , EPDN gasket, silicon sealent etc. complete as per detailed drawings, mock sample and specifications.

Mosquito Jali : Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm With 12 mm mild steel U beading all complete.

MS Fabricated Door: Providing Fabrication & erection 3 mm thick M.S. sheet/plate door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces. including CNC cutting/Engraving as per reference image given by Architect. The work includig necessary fabrication work, fittings, fixtures, accessories, pivot, door, handle, lock etc complete. finish with Anti corrosive paint with primer as per approved shade by Architect. The scope includes loading, transportation, unloading and delivery and erection site of all fabricated structures, alignment and welding of all structures true to line, level, plumb and dimension. sample mock shall be approved from Architect/EIC. Shop drawing shall be provided by Contractor.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved anticorrosive paint all complete. Fixed to steel windows by welding

Indian Type W.C. : Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Anglo Indian WC: Model equivalent - Jaquar- ECS-WHT-355SNPP With PP Normal Close Seat Cover, Hinges, Fixing Accessories And Accessories Set, Size: 475x575x395 mm, S Trap . including cutting and making good the walls and floors where required with all labour and materials. All works to be carried out as per instructions and direction of Engineer-in-charge. Model Equivalent to Jaquar-CNSWHT-963UFSM

Flush Valve : Providing and fixing Meropole Flush valve of as per approved make list . Work complete including all type of finishing. Model Equivalent to Jaquar FLV-CHR-1093N

Health faucet: Providing and fixing 8mm dia. Health faucet as per approved make list with flexible pipe of 1.2mt. length and holding stands complete. Work complete including all type of finishing. Model Equivalent to Jaquar ALD-CHR-573

Wash Basin : Providing and fixing under counter Wash Basin including fittings and waste coupling and fixing on wash basin counter by tile adhesive of approved make. Work complete including all type of finishing. Model Equivalent to Jaquar CNS-WHT-701

Providing and fixing 15mm dia. Angular Stop Cock with flange as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar EKO-CHR-33053

Providing and fixing Pillar cock as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar COS-CHR-103001M

Urinal : Providing and fixing Urinal as per approved make list , with necessary coupling of approved make for wash basin & sink. Work complete including all type of finishing. Model Equivalent to Jaquar ECS-WHT-253

Urinal Flush Valve : Providing and fixing auto closing concealed Urinal flush valve with flange as per approved make list , with necessary coupling of approved make for urinal. Work complete including all type of finishing. Model Equivalent to Jaquar PRS-CHR-077

Urinal partition: Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Nirali : Grace Plain- 510MM X 432MM

Providing and fixing Sink Cock with regular spout with wall flange as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar FLR-CHR-5347N

Providing and fixing CP Brass 32mm size Bottle trap with 300mm & 190mm long wall connection pipes & wall flange of approved quality & make and as per the direction of Engineer-in-charge. with necessary coupling for wash basin & sink. Model equivalent to Jaquar ALDCHR-769L300X190

Providing and fixing Over head shower with shower arm as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar OHS-CHR-1989+ SHA-CHR-477

Providing and fixing Opal prime bath tub spout with wall flange as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar SPJCHR-15429PM

Providing and fixing Grab bar vartical swing as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar WAC-SAPBG0800CS

Providing and fixing Grab bar 692mm long as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar WAC-SAPBR0600CS

Providing and fixing Single lever Diverter consisting of operating lever cartridge sleeve wall flange with button assembly as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar EKOCHR-33079NK+ ALD-CHR-079N

Providing and fixing 6 mm thick mirror of Saint Gobain/ Modiguard / Asahi as per approved make shall be fixed with profile frame section (Silver/gray/black etc.). Provision shall be made for conceal led light work as per detailed drawing / instruction of architect complete. Rate shall be inclusive of frosting work as per detail drawing.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet: Sand cast iron S&S as per IS: 3989

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

ACP Clading: Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Aluminium Fins/Louvers (Elevation): Supplying and Installing of METALIUMTM make U- Shaped Baffle 50*50*50mm (50mm gap) Galvanized Steel 0.50mm TCT plain wooden powder coating on visible surface of Panel and supporting structure in black color Exterior Louver System. Panel (Galvanized Steel): Metalium make square edge P-50 series panels, 50 * 50 * 50 mm& 0.50 mm TCT Galvanized Steel. Panel length is up to approx. 3 mtr. Panels shall be wooden powder coated on visible surface with special Exterior Grade powder to enhance property of Fadedness Resistivity. P-50 Carrier (U Shaped): Black enameled Galvanized Steel Carrier of 20mm wide at bottom x 39mm deep x 0.6 mm thick in a standard length of 8’ with cutouts to hold the panel in a module of 100 mm centre to centre at a distance of 1 mtr. Carrier and suitable structure shall be powder / coil coated on exterior face to enhance properties of Fadedness and corrosion resistivity. Installation Details: GS Clit shall be fixed on vertical columns with dash fasteners at distance not more than 1 mtr. Centre to centre on which Tubular Stud sections will be laid with corrosion proof screws and on this rigid structure carrier shall be fixed vertically / horizontally at distance of 1 mtr. Centre to centre. Panel shall be clipped to carriers. Rate shall inclusive of mock up sample, all materials, loading, unloading, transportation, placing at all floors and for all leads, all accessorie , Scaffolding etc as described in item description. Work complete as per the detailed drawing , mockup sample and instruction of Architect/Client.

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm/m²

Fabricated : Design, Fabrication & erection of steel structure as per drawings including materials, consisting of plates, rolled steel joists, channels, angles, chequered plates etc and also rectangular / square hollow steel sections, insert plates in RCC/Brickwork, anchor bolts for steel structure, sleeve pipes, anchor nuts, washers etc, straightening of raw steel if required, fabrication of steel structures with primer and minimum two coats of anti corrosive paint including preparation of supplementary sketches and detailed bill of materials supply of bolts, nuts, washers, shims, packs, putty. gas, welding electrodes and all other consumables, as required and carrying out surface preparation all complete. The scope includes loading, transportation ,unloading and delivery and erection site of all fabricated structures,, alignment and welding of all structures true to line, level, plumb and dimension, including rectification if any, splicing, site assembly all as per technical specifications and drawings, ,all complete.Contactor shall provide stability certificate for the fabrication structure. Rate inclusive of shop drawing.

Gypsum Board False Ceiling: Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Grid ceiling : Providing and fixing false ceiling at all heights with Eco – Friendly light weight calcium Silicate Modular Acoustical grid ceiling of dimension 595X595 MM having 15 MM thick integral densified tegular edges reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50(minimum) as per IS 8225:1987, Product should have Zero VOC( Eco- friendly ) & More than 50% Recycled contents for high green building Poi Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4)& BS:476 (part 6 &7), Also the product should UL-723 & ASTM Complying 100% with NFPA Guide lines Light reflectance of 85% (minimum). Non-combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043W/mK as per ASTM 518:1991, in true horizontal level suspended on inter- locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of theEngineer-in-Charge.

Full Height Partition Gypsum Partition (60min. fire rating) : 100mm thick Gypserra™ stud partition which includes inner layer of tapered edge 12.5mm thick Gypboard® Plain (conforming to IS 2095 Part 1:2011, Certified board) of size 1219x2438mm and outer layer of tapered edge 12.5mm thick Gyproc®Fireline board of size 1219x2438mm is screw fixed to C-stud.48x0.5mm Gypserra™ C-stud {Material-IS 513, Y/S-300Mpa, Finish - AZ150 (IS 15961)} placed at 610mm c/c in 50x0.5mm Gypserra™ {Material-IS 513,Y/S-300Mpa, Finish - AZ150 (IS 15961)} floor and ceiling channel. Floor & Ceiling channel is anchored to the floor & True ceiling using Gyproc® Rawl plug Ø8x45mm {Material-IS 513 CR1 grade, Zinc coating, Pull Out Load-6.8kN for M30 concrete grade} /Hilti X-GN20MX anchor fasteners at 600mm c/c in centerline manner.Floor channel to be wrapped with 70μ Self Adhesive LDPE moisture barrier film to further improve corrosion resistance performance. 12.5mm thick Gypboard® Plain board strip of 50mm width is placed between ceiling channel and RCC ceiling slab when deflection is more than 10mm & fire rating is more than 30min. A Gypserra™ noggin channel {Material-IS 513,Y/S-300 Mpa, Finish - AZ150 (IS 15961)} of 50x0.5mm width has to be provided at the horizontal joints of the two boards. First layer of Gyproc® boards to be screw fixed with Gyproc® drywall screws of 25mm at minimum spacing of 600mm at centre and 600mm at periphery. Second layer to be screw fixed Gyproc® drywall screws of 35mm at minimum spacing of 300mm at centre and 300mm at periphery. 50mm Glass wool slab of density 20kg/m³ shall be placed in metal framework. Glass wool holding clip should be used to hold Glass wool slab in its position. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gyproc® Pro-Fill Jointing compound, (Conforms to ASTM C475), Gyproc® Joint Paper tape or fiber tape. The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant. All other detailing and specifications to be followed as per approved drawing of Gyproc. Note: Applicator need 60min. fire rating certificates from Gyproc. Rate shall include cost of making of all cut-outs for light fixtures, switchboards gadgets, gizmo, pelmets, grooves, beads and also provide support/template where ever required & For door frame fixing, storages, shelves, paneling etc extra Wooden members to be used shall be of CP teak wood only. Including skirting /MDF board/wooden skirting cut out as per EIC instruction at siteThe rate shall be in sq.mt for all floors and at all heights including all costs. including ply base for fixing of TV or Overhead storage wherever required, The rates are also inclusive of necessary scaffolding, tools, tackles,, safety measures , Internal partial support (between two sturd) at 7' height.The shop drawing (or a sample mock of 5 Sqm minimum of the frame work and partition) shall be approved from EIC and Architect. All exposed corner shall be covered with perforated angle as per manufacturer's specifications or as directed by EIC.

Comprehensive Maintenance : 10 Passenger LIFT : everything is including all cover parts , accessories , machineries, fittings , fxitures etc Comprehensive Maintenance : 10 Passenger LIFT : 5 STOP , 1 MPS, Schindler 3000 MRL : Second Year

Comprehensive Maintenance : 10 Passenger LIFT : 5 STOP , 1 MPS, Schindler 3000 MRL : Third Year

Comprehensive Maintenance : 10 Passenger LIFT : 5 STOP , 1 MPS, Schindler 3000 MRL : Fourth Year

Comprehensive Maintenance : 10 Passenger LIFT : 5 STOP , 1 MPS, Schindler 3000 MRL : Fifth Year

Plumbing

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

65 mm nominal inner dia Pipes

80 mm nominal inner dia Pipes

100 mm nominal inner dia Pipes

Providing & fixing Thermal Insulation of Hot water pipe with Nitrile/CCCL as per Specification. (A) 9 mm thick thermal insulation for 20 mm dia pipe

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

80 mm nominal bore

100 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 65 mm nominal bore: Horizontal

65 mm nominal bore: Vertical

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Supplying, installing, testing & commissioning of Heat Pump with SS Storage Tank of 4000 Litres as per prevailing IS code comprising of Solar flat locket collector, stainless steel hot water storage isolated tank of following capacity in liter / day (LPD) (Including inlet & outlet pipe lines) . Capacity of 4000 LPD, with 1W + 1S (150 LPM , 30 mtr Head) Booster Pump with control panels and required accessories and piping to complete the job.

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of the water should drop by 15˚C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.

Supplying & erecting reverse osmosis (RO) water purification system with M.S. powder coated pedestal frame, prefilter housing carbon filter suitable buster DC pump, auto low & high pressure switches with following size of LPH capacity & erected as directed. [E] 200 LPH with 1 phase / 3 phase Raw water pump of 1000LPH @ 2.5kg/cm2 (1N0 - Kirloskar/CRI/Lubi) , Dual media filter 10"x54" (1 No), Micron catridge filter 20" x 2.5" - (1No), High pressure pump 1000LPH @ 10kg/cm2 - (1No - Shimge /CRI /Lubi) , RO Membrane housing with RO membrane of 40*40 - ( 1 No),RO pressure tube 4" x 1E-(1No), 0-1200LPH Rotameter-(2 Nos). Recovery Rate 50%.

Supply, Installation, Testing & Commissioning of 3 Layered HDPE Tank Vito Astral Make , UV resistant layer of highest quality protecting water from harsh UV ray & low heat absorption from sunlight, Anti microbial anti viral copper sheild, complete with accessories

Providing, Fixing, testing & commissioning 6 kg/ sq. cm PVC Pipe ISI marked brand as per IS 4985/IS 13592 above 40mm dia (self fit type) complete with PVC Fittings conforms to IS: 7834 / IS: 10124 including all fittings (plain or door) e.g. bend, single tee, double tee, single Y, double Y, junction, offsets, access pieces etc. The work including solvent jointing hydraulic testing the joints & pipes as mentioned in the specification etc. making holes including chasing in solid block masonry walls with groove cutting machine to required width and depth, making holes in brick or RCC wall as per requirement ,clearing the debris, grouting of concealed pipes, making good the chase by using 1:3 cement mortar, covering of pipe with PCC 1:4:8, making good the wall and floors, making connection with down take to satisfaction of engr / arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing provided for all places, all heights & all levels (Internal work for toilet block and underground work) a) 40 mm dia OD

b) 50 mm dia OD

Providing, Fixing, testing & commissioning SWR PVC Pipe ISI marked brand as per IS 13592 & fittings conform to IS: 14735, Rubber ring conforms to IS:5382 including all fittings (plain or door) e.g. bend, single tee, double tee, single Y, double Y, junction, cowls, offsets, access pieces etc. The work including rubbering socketed solvent jointing, hydraulic testing the joints & pipes as mentioned in the specification etc. making holes in solid block masonry /concrete walls as per requirement , clearing the debris, providing & fixing zinc coated electro galvanised steel clamp with EPDM rubber, casing & lining for fixing pipes and making good the wall and floors, making connection with trap & cowl to satisfaction of engr / arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing for all floor, all places & all heights (Concealed work Internal toilet block) a) 75mm dia. OD (type B)

b) 110mm dia. OD (type B)

Providing, Fixing, testing & commissioning SWR PVC Pipe ISI marked brand as per IS 13592 & fittings conform to IS: 14735, Rubber ring conforms to IS:5382 including all fittings (plain or door) e.g. bend, single tee, double tee, single Y, double Y, junction, cowls, offsets, access pieces etc. The work including rubbering socketed solvent jointing, hydraulic testing the joints & pipes as mentioned in the specification etc. making holes in solid block masonry /concrete walls as per requirement , clearing the debris, providing & fixing zinc coated electro galvanised steel clamp with EPDM rubber, casing & lining for fixing pipes and making good the wall and floors, making connection with trap & cowl to satisfaction of engr / arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing for all floor, all places & all heights (Internal work - Exposed on wall) : d) 110mm dia. OD

Providing, Fixing, testing & commissioning SWR PVC Pipe ISI marked brand as per IS 13592 & fittings conform to IS: 14735, Rubber ring conforms to IS:5382 including all fittings (plain or door) e.g. bend, single tee, double tee, single Y, double Y, junction, cowls, offsets, access pieces etc. The work including rubbering socketed solvent jointing, hydraulic testing the joints & pipes as mentioned in the specification etc. making holes in solid block masonry /concrete walls as per requirement , clearing the debris, providing & fixing zinc coated electro galvanised steel clamp with EPDM rubber, casing & lining for fixing pipes and making good the wall and floors, making connection with trap & cowl to satisfaction of engr / arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing for all floor, all places & all heights (Internal work - Exposed on wall) : 150mm dia. OD

Providing, Fixing, testing & commissioning SWR PVC Pipe ISI marked brand as per IS 13592 & fittings conform to IS: 14735, Rubber ring conforms to IS:5382 including all fittings (plain or door) e.g. bend, single tee, double tee, single Y, double Y, junction, cowls, offsets, access pieces etc. The work including rubbering socketed solvent jointing, hydraulic testing the joints & pipes as mentioned in the specification etc. making holes in solid block masonry /concrete walls as per requirement , clearing the debris, providing & fixing zinc coated electro galvanised steel clamp with EPDM rubber, casing & lining for fixing pipes and making good the wall and floors, making connection with trap & cowl to satisfaction of engr / arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing for all floor, all places & all heights (Internal work - Exposed on wall) : 200mm dia. OD

Providing, Fixing, testing & commissioning SWR PVC Pipe ISI marked brand as per IS 13592 & fittings conform to IS: 14735, Rubber ring conforms to IS:5382 including all fittings (plain or door) e.g. bend, single tee, double tee, single Y, double Y, junction, cowls, offsets, access pieces etc. The work including rubbering socketed solvent jointing, hydraulic testing the joints & pipes as mentioned in the specification etc. making holes in solid block masonry /concrete walls as per requirement , clearing the debris, providing & fixing zinc coated electro galvanised steel clamp with EPDM rubber, casing & lining for fixing pipes and making good the wall and floors, making connection with trap & cowl to satisfaction of engr / arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing for all floor, all places & all heights (Internal work - Exposed on wall) : 250mm dia. OD

Providing, Fixing, testing & commissioning SWR PVC Pipe ISI marked brand as per IS 13592 & fittings conform to IS: 14735, Rubber ring conforms to IS:5382 including all fittings (plain or door) e.g. bend, single tee, double tee, single Y, double Y, junction, cowls, offsets, access pieces etc. The work including rubbering socketed solvent jointing, hydraulic testing the joints & pipes as mentioned in the specification etc. making holes in solid block masonry /concrete walls as per requirement , clearing the debris, providing & fixing zinc coated electro galvanised steel clamp with EPDM rubber, casing & lining for fixing pipes and making good the wall and floors, making connection with trap & cowl to satisfaction of engr / arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing for all floor, all places & all heights (Internal work - Exposed on wall) : 315mm dia. OD

Providing & fixing PVC MFT of self cleansing design having water seal not less than 50mm with necessary distance piece & making connection with SS Grating, making necessary slab / wall holes & cutting walls, grouting with M-15 CC all around with brick masonry support of 350x350 mm up to bottom of trap etc. complete as per specifications & drawing provided at all places, all levels & all height a) 110 mm inlet and 75 mm outlet

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes : Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

2 way 5/6A Switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 1 or 2 Module

3 Module

4 Module

6 Module

8 Module

12 Module

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door

12 Way Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of200 A tinned copper bus bar, common neutral link, earth bar,din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Double pole

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

MAIN LT PANEL: Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board necessary IP-42 and above protection as per approval from engineer incharge made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary accesories , supporting angles/ flats channel including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with erection of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses/MCB for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket,heavy duty end terminal connection,danger notice board,necessary ventilation,earthing strip complete. The Panel shall be painted with epoxy powder coating. (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers (B) The standard companies switch gear shall be used and only manufacturers at CPRI approved factory with following size. as per Description Below : Main LT Panel Incomer : 800A, FP ACB, 25KA CT : 800/5A - 3nos Indication Lamp : R,Y,B, On OFF Trip Voltmeter with VSS , Ammeter with ASS Switch Busbar Chamber : 800A, FP aluminium Busbar Outgoing : 250A, FP, MCCB, Thermal Magnetic Release - 2 Nos. 125A, FP, MCCB, Thermal Magnetic Release - 14 Nos. 63A FP MCB, 10KA - 8 Nos 40A FP MCB, 10KA - 8 Nos

Smart Meter Panel (with Compartment Based & Lock & Key Arrangement). Panel shall have Provision Space for Ethernet Switch. Incomer : 125A FP MCCB Outgoing : 40A DP MCB, 10KA - 20 nos IOT Based Smart KWH Meter with RS-485 Output Port - 20 nos

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

(C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core)

(D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

(F) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core)

(H) 3 1/2 core 185 Sq. mm ( 95 Sq. mm 1/2 core)

(I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core)

(J) 3 1/2 core 300 Sq.mm ( 150 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (C) 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 4 core 10 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (A) 4 core 16 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (B) 2 to 4 core 6 Sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 35 sq. mm (28mm)

3½ X 50 sq. mm (28mm)

3½ X 70 sq. mm (28mm)

31/ X 150 sq. mm (50mm)

31/2 X 185 sq. mm (57mm)

3½ X 240 sq. mm (62mm)

3½ X 300 sq. mm (70mm)

4 X 16 sq. mm (28mm)

"Supply, Installation, Testing & Commissioning of Anodized Aluminium 4ft Wall/ceiling surface mounted Batten light, Operating Voltage 220 to 240, Power Consumption - 20 Watt ±5%, CCT to be confirmed with the architect - (6500K, 4000K, 3000K), Lumen Efficacy More then 90LPW Ref. Model - TISVA (Usha International Ltd) : 82FL20W65AL2 RAY PRM PRO ALUM LED BATTEN 20W 65K 1.1M or equivalent from Lighting Technologies(LT)/ Regent Lighting/Philips lighting"

"Supply, Installation, Testing & Commissioning of SMD 15w Edgelit Surface Panel Light made with Die Cast Aluminium powder coated, Operating Voltage 220 to 240, Power Consumption - 15 Watt ±5%, CCT to be confirmed with the architect -- (6500K, 4000K, 3000K), Lumen Efficacy (76.8LM/W-3000K, 80.12LM/W-4000K, 82.3LM/W-6500K), Surge Protection ≥2.5 KV, PF≥0.9, THD<10. W Ref. Model - TISVA (Usha International Ltd) : 81671526203M EZIO LED PNL DLP152623M 15W 65K SR or equivalent from Lighting Technologies(LT)/ Regent Lighting/Philips lighting"

"Supply, Installation, Testing & Commissioning of 15W SMD Edgelit Recessed Panel Light made with Die Cast Aluminium powder coated, Operating Voltage 220 to 240, Power Consumption - 15 Watt ±5%, CCT CCT to be confirmed with the architect -- (6500K, 4000K, 3000K), Lumen Efficacy (78.40/W-3000K, 81.39LM/W-4000K, 84.10LM/W-6500K), Surge Protection ≥2.5 KV, PF≥0.9, THD<10. Ref. Model - TISVA (Usha International Ltd) :81671516203M EZIO LED PNL DLP151623M 15W 65K RR or equivalent from Lighting Technologies(LT)/ Regent Lighting/Philips lighting"

"Supply, Installation, Testing & Commissioning of " 1200mm 36W Mounting:Recess mounted downward profile,Housing :Extruded Aluminium with ABS End Cap.,Diffuser:PMMA,IP rating:IP20,Input Voltage:130V AC T0 300V AC,1215mm X 37mm X 90mm CCT to be confirmed with the architect -- (6500K, 4000K, 3000K), Efficacy More then 90LPW, Surge Protection ≥2.5 KV, PF≥0.9, THD<10. Ref. Model - TISVA (Usha International Ltd) :Steller LED PL363304 36W 4K 5575SP or equivalent from Lighting Technologies(LT)/ Regent Lighting/Philips lighting"

"Supply, Installation, Testing & Commissioning of " 1200 mm 36W Suspnded downward profile,Housing :Extruded Aluminium with ABS End Cap.,Diffuser:PMMA,IP rating:IP20,Input Voltage:130V AC T0 300V AC,1215mm X50 mm X 90mm CCT to be confirmed with the architect -- (6500K, 4000K, 3000K), Efficacy More then 90LPW, Surge Protection ≥2.5 KV, PF≥0.9, THD<10. Ref. Model - TISVA (Usha International Ltd) :Steller LED Suspended or equivalent from Lighting Technologies(LT)/ Regent Lighting/Philips lighting"

"Supply, Installation, Testing & Commissioning of Anodized Aluminium Profile with Cutout width 17.1mm by Depth 8mm profile with Diffused PS/PMMA cover for Recess Mounting suitable for placing flexible SMD LED strip light with wattage 14-15W/mtr per strip, LED Desnsity should be equal to or more than 180 LED per metre, CCT to be confirmed with the architect , Efficacy should be more than 90 LPW, Compatible with Non Integral Electrically isolated High efficiency electronic remote Constant Voltage 24VDC driver with rated input voltage of 240V, Power factor > 0.95 and THD < 10%, CRI 80, SDCM 3, Driver should have Inbuilt surge protection of morethan 4KV, Miswiring Protection, Over voltage protection & Short circuit protection. LED Strip Should be IP20. Ref. Model - TISVA (Usha International Ltd) :Lume Strip light or equivalent from Lighting Technologies(LT)/ Regent Lighting/Philips lighting""

"Supply, Installation, Testing & Commissioning of Anodized Aluminium 2ft Wall/ceiling surface mounted Batten light, Operating Voltage 220 to 240, Power Consumption - 10 Watt ±5%, CCT to be confirmed with the architect - (6500K, 4000K, 3000K), Lumen Efficacy More then 90LPW Ref. Model - TISVA (Usha International Ltd) : RAY PRM PRO ALUM LED BATTEN 10W 65K or equivalent from Lighting Technologies(LT)/ Regent Lighting/Philips lighting"

"Supply, Installation, Testing & Commissioning of " BOLLARD Light 700-1000MM Height, Die Cast powder coated Aluminium. IP 65 Protection, Wattage: 15W, CCT: 3000K.Operating Voltage : 220 to 240V, Wattage : 4 Watt, Lamp Source : 15 Watt In-built LED, CCT to be confirmed with the architect -- (6500K, 4000K, 3000K), Ref. Model - TISVA (Usha International Ltd) :LS OD BL SMD LED LB15S131 15W 3K IP65 or equivalent from Lighting Technologies(LT)/ Regent Lighting/Philips lighting"

1.Supply, Installation, testing & erecting of decorative pole top mounting with 35-50w 3000k IP65 Post top light 2. PC Injection Moulded Diffuser for high light transmitivity .Fixture Lumen Output should be greater than 80 lumen per watt. 3. Min IP 65 Ingress Protection for Fixture and IP65 for Driver . 4. External IP66 Silicon Potted driver for ensuring better reliability and safety . 5. Fixture should be warrantied for 5yrs for 50,000 hrs @ L70 ( LM79 from NABL accredited Lab to be submitted along with Letter from Manufacturer for the Life class claim of L70 @ 50,000 hrs.) 6. The product should be Manufactured in India (all the Components should be manufactured in India except the Led source which can be imported . (Approved Led source Nichia , Cree, Lumileds , Osram Only) 7. PF >=0.9 and THD <=10 % (Certificate need to be submitted from NABL Accredited lab) 8. The manufacturer should be ISO 9001 -2008 and ISO 14001 -2004 Company 9. . The Fixture should be provided with a suitable cradle for sturdy mounting. 10. Have their own driver Manufacturing Facility. Ref. Model - Lighting Technologies Primus 40w Post Top or equivalent from TISVA (Usha International Ltd)/ Regent Lighting/Philips lighting"

5 mtr MS Pole as per necessary accessories and specifications for Post top mounting as per Govt of Gujarat Schedule of Rates .

Supplying & erecting approved make low noise decorative Exhaust fan having square frame ABS body with inbuilt lowers & square frame.250mm with 1350 RPM Cat.II

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box.

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected with necessary hook of 10 mm M.S. Round Bar.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with necessary finishing.

Supplying and erecting approved make online Un-interruptible Power Supply system comprising flat cum-boost charger, static Inverter & sealed maintenance free SMF batteries. The charger having operating capacity for input 160-270V AC & inverter having output 230V,50 Hz Ac with 0.8 load power factor with battery, over/under voltage output with over load & short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following power backup.with MS painted batteries stand, 10% Overload capacity for momentary load. (D) 10 KVA with 1Hr Backup

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable (A)50 mm outer dia

ELV Work

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete withmounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying & erecting push button type telephone instrument having speaker phone Caller ID & hands free dialling system & 30 memories with display system (a) Single line BPL / SONY/ BEETEL or equivalent make.Cat : III & As per approved Make List.

Telephone socket outlet

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Supply, installation, testing and commissioning of Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge.Modem Jack for Computer Open RJ-45 CAT III.

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction [D] CAT - 6e ( For LAN, Telephone & Camera).

SITC of Jack Panel, fully loaded with 24 nos. UTP ports for PCB based IO Jacks (RJ45, TIA-568C Category-6, Installation and Termination of all 24 nos. Catergory-6 UTP , unloaded with individually replaceable 24 nos. Category-6 I/O Jacks complying with TIA-568.C.2, as per given jack specification Shall be suitable for loading unshielded & shielded jacks for different category systems (CAT 6 & CAT 6A)

SITC of company fabricated patch cords shall conform to Cat- 6 & conductor shall be stranded for better flexibility Shall support network line speeds up to 1 Gbps Shall have RJ-45 jacks. (B) 2 Mtr

SITC of 24 x 10/100/1000BASE-T ports 4 x Gigabit RJ45/SFP Combo ports Advanced L2 switching and security features L2+ Static Routing Optional “standard mode” or “surveillance mode” management user interface. POE Switch

SITC of 48 x 10/100/1000BASE-T ports 4 x Gigabit GbE/SFP combo ports Advanced L2 switching and security features L2+ Static Routing Optional “standard mode” or “surveillance mode” management user interface. POE Switch

SITC of Faceplate for RJ45 Port with ABS /Metal Body square plate, dimension as per commercially available modular office furniture. Shall Have Icons, Shutter, Screw Cover, Label Cover, Jack holder with neccessory connections (A) 1-port

Providing & erecting Fiber Optic Cable, 50/125μ, OM3 Outdoor Shall be 50μ, Multi mode OM3 non-metallic armored cable as per ISO/IEC-11801 Shall be able to meet Gigabit & 10 Gigabit Ethernet performance up to 300 meters requirement specified by IEEE 802.3z (1000 Base-X) & IEEE 802.3ae (10G Base-X) Shall be suitable for using in the building shaft and outdoor laying, Shall be Unitube Jacketing Material Shall be HDPE with nominal thickness of 2.1mm and overall diameter (Nominal )10mm (A) 6 core Multi mode

Providing & erecting Fiber Optic SC/LC style fully loaded Patch Panel (FOPP), 19" Rack Mount with following nos of OM3 50/125μ Pigtails.as per ISO/IEC-11801-OM3 Pigtails with SC/LC Type Connectors Pigtail Attenuation ≤0.3dB measured at 850nm Acc to IEC 61300-3-4 Method B Return Loss ≥ 30dB, in mated condition Pigtail Cable Information – Outer Jacket Diamter – 0.9mm, Outer Jacket Material – LSZH Shall have all accessories including coupler plates pre-loaded with duplex LC couplers (OM3), pigtails for terminating fibers on the FOPP Shall be Front Patching Type, 1U high and rack mountable on standard 19” rack with mounting arrangements. (A) 12F Loaded with Coupler, Pigtail and Splice Trays

Providing & Erecting Netwrok rack with following capacity with Necessary cooling fan,Cable manager,6A PDU,equipment rack with necessary mounting accessories. (C) 12 U

Providing & Erecting Netwrok rack with following capacity with Necessary cooling fan,Cable manager,6A PDU,equipment rack with necessary mounting accessories. (I) 26 U

Providing & Erecting Netwrok rack with following capacity with Necessary cooling fan,Cable manager,6A PDU,equipment rack with necessary mounting accessories. (B) 6 U

Supply, Installation, testing & commisioning of Wire less WiFi Router with below specification Networking Interface : (1) 10/100 Ethernet Port Buttons : Reset Antennas ,Power Method : Passive Power over Ethernet (12-24V) Power Supply : Included 24V, 0.5A PoE Adapter Maximum Power Consumption : 6 W Maximum TX Power : 27 dBm BSSID : Up to Four Per Radio Power Save : Supported Wireless Security : WEP, WPA-PSK, WPA-TKIP,WPA2 AES.

DOME CAMERA-Full HD 1080p 25/30 fps image with a 1/2.7" or 1/2.8" 2 MP sensor, 2.7–12 mm, F1.4,zoom lens,True WDR up to 140 dB ensures glare-free images,H.264 and MJPEG codec, triple stream support, IR LEDs provide up to 50 m (150’) of illumination in dimly lit or nighttime scenes, Waterproof (IP67) and IK10 vandal resistant camera housing ,ONVIF Profile S and G compliant

Network Video Recorder: Network Video Recorder of 64 Channels Dual-core embedded processor,16 channel IP Cmaera Input,Video Resolution2560×1920, 2048×1536, 1920 x 1080, 1280 x 1024, 1280 x 720, 1024 x 768,Hard Disk 4 SATA ports, up to 4TB Supported,1 HDMI, 1 VGA, 2 USB2.0, 1 RJ45 Interface,Working Temp-10 ~+55°C / 10~90%RH / 86~106kpa, Protocal supported HTTP, TCP/IP, IPv4/IPv6, UPNP, RTSP, UDP, SMTP, NTP, DHCP, DNS, IP Filter,PPPOE, DDNS, FTP, Alarm Server,ONVIF Version 2.3

Western Digital WD 5TB Hard Disk Drive, USB 3.0 with Automatic Backup, 256 Bit AES Hardware Encryption,Password Protection,Compatible with Windows and Mac, External HDD-Black

SITC of 42 Inch 500 NTS Brightness professional Display with Direct-Type LED, Viewing Angle : 178 Degree Verti, 178 Degree Hor. Operation 27x7, Native Resolution 3840 x 2160 (16:9) - UHD, 4 x USB (2 x 2.0, 1 x 2.0 internal, 1 x Type C), 0-40°C, ≤0.5 W, HTML 5 Browser Opera(4.9), Yes(internal) IEEE 802.11 a/b/g/n Dual WiFi certificated, BIS, YES CLASS A 3dB margin.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

FIRE FIGHTING BOQ

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 900 LPM at 35m Head

Supply, Installation, Testing and Commissioning of 100 mm dia Pressure Gauge of range 0 - 15 Kg / cm² conforming to IS - 3624 having bourdon tube of stainless steel 316 in cast aluminium, stove enameled, black, weather proof case with outer, screwed aluminium bezel and complete with necessary U-type stainless steel siphon tube and cock including providing suitably painted angle iron support to the tube etc.as per specification complete as required.

Supply, Installation, Testing and Commissioning of Gun Metal Air Release Valve with necessary fittings. Size: 25 mm

Supply, installation, testing and commissioning of Pump on/off Remote switches to each hose reel with required accessories.

Supply, installation, testing and commissioning of XLPE insulated copper armoured Cable from each Pump on/off switches to Panel with all necessary accessories. Size: 4 core x 2.5 sq. mm

Supply, installation, testing and commissioning of SS Ball Valve. a) 25mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80mm dia

100mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80mm dia

100mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 100mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 100mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 40m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Charges for Liasoning with CFO and getting all approvals and permissions & NOC 's required for fire fighting at various stages & after completion of the project. (All official and receipted payments would be submitted and Re- imbursed) Taking approval /NOC form CFO

Supplying, installation, testing & commissioning of Photo luminescent non toxic, non radioactive, maintenance free self glowing exit signs comprising zinc sulphide chargeable crystals which can glow in dark; printed on U-1000 photo luminiscent aluminium sheet 1.0 mm thick containing luminiscent 111 as base chemical cover with UV stabilized coating job complete with SS screws for wall mounting or to be hanged on rust proof chain for ceiling mounting complete in all respects, plate size 12" X 18" (general size, may increase or decrease depending on site requirements). Make : Glo-line, Paras Line, Glow-shine.

Supply installation testing and commissioning of CO2 type Fire Extinguisher of 4.5 kgs capacity made from brand new seamless drawn steel cylinder conforming to IS : 7285 with ISI mark and Chief of controller of explosives approval, fitted with wheel valve conforming to IS: 3224 with ISI mark, with discharge hose and horn and supplied complete with initial charge overall conforming to IS: 15683 with ISI mark and wall bracket. Fire Rating 21B

Supply installation testing and commissioning of Dry Chemical Powder 6.0 kg capacity fitted with discharge control valve ( squeeze grip type ), inside co2 gas cartridge of 120gms conforming to IS: 4947 with ISI mark and DCP powder as per IS: 14609 ( for ABC class ) with ISI mark packed in 5kgs HDPE bags, with discharge hose and open nozzel and supplied complete with initial charge overall conforming to ISI: 15683 ISI mark and wall bracket . Fire Rating 34B.

External Development (Paver block, Kerbing, stone sitting, otta etc.)

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m : All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. a) Concrete of M25 grade with minimum cement content of 330 kg /cum : All works upto plinth level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. all level, all floor. Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Exterior Paint: Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cementmortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and laying Polished Granite stone flooring colour of Black, Cherry/Ruby Red or equivalent in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. ; 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. : All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge : Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling with all lead and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site. work complete including royalty, all type of tools, tackles, scaffolding, safety measures, loading, unloading, transportation, all heights, all levels, all lead & all lift etc complete as per instruction of Architect/EIC. (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, work complete including royalty, all type of tools, tackles, scaffolding, safety measures, loading, unloading, transportation, all heights, all levels, all lead & all lift etc complete as per instruction of Architect/EIC. (manure measured in stacks will be reduced by 8% for payment) :

Rough dressing the trenched ground including breaking clods. work complete including all type of tools, tackles, scaffolding, safety measures, loading, unloading, transportation, all heights, all levels, all lead & all lift etc complete as per instruction of Architect/EIC.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation

Fine dressing of the ground.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Shrubs:-Providing and planting the saplings of shrubs as per approved varieties sample by Architect. complete as per detail specification.Work complete including all labour, tools, tackles, maintenance with 30 days or more till the shrubs forms a thick etc

Trees :-Providing and planting the saplings of trees of approved varieties by Architect. complete as per detailed specification. .Work complete including all labour , tools , tackles , maintenance with 30 days or more till the tree forms a thick etc

Bottle Palm :-Providing and planting the saplings of Palm tree of approved varieties by Architect. complete as per detailed specification. .Work complete including all labour , tools , tackles , maintenance with 30 days or more till the Palm tree forms a thick etc

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered GMDC or any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.

Rate only Items

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS:9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. All works upto plinth level : Concrete of M10 grade with minimum cement content of 220 kg /cum

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT: 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

CEMENT PLASTER (IN COARSE SAND): Providing and laying plaster : 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand)

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. - 10.5mt-13mt

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar creme out upto surface using white cement including rounding off junctions and extending them upto 15 cm along the wall,clearing with water and oxalic acid etc. as directed.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. : For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm.

Providing and laying Polished Granite stone flooring colour of Black, Cherry/Ruby Red or equivalent in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Double Leaf Flush Door with glass view panel and finish with laminate : Providing and fixing in position 40 mm thick BWP grade Double leaf flush doors of approved make and finished with both side 1 mm thick VNR laminate as approved sample ,with glass view panel, 8mm thick toughened Milky glass view panel, Hardware system as per approved make & sample (door closer , Mortise lock, Door handle ,lock , Door stopper). work complete including all type of hardware, fittings , fixtures ,as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client. Equivalent to VNR Series Laminate.

Single Leaf Flush Door with glass view panel and finish with laminate : Providing and fixing in position 40 mm thick BWP grade single leaf flush doors of approved make and finished with both side 1 mm thick VNR laminate as approved sample ,with glass view panel, 8mm thick toughened Milky glass view panel, Hardware system as per approved make & sample (door closer, cylidrical lock, Door handle ,lock , Door stopper). work complete including all type of hardware, fittings , fixtures ,as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client. Equivalent to VNR Series Laminate.

Awning window : (Domal 27 mm series) Supply & Fixing of Fixed glass window with powder coated as per by approved make & sample by architect/EIC. frame section: 45 x 45x 1.5 mm Glass : 5 mm thick tinted grey toughened glass of saint gobain or approved make list including necessary fixtures and fastening , EPDN gasket, silicon sealent etc. complete as per detailed drawings, mock sample and specifications.

Collapsible steel shutter: Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Precast cement concrete jali : Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. - 50 mm thick

WPC Jali : Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Polycarbonate sheet roofing : Providing and Fixing of COXWELL DOMES ROOF SYSTEM consisting of MultiCell Polycarbonate Panel System of approved color in 10 mm Thick (minimum) 6 WALL -5 CELL having uniform in color, Vertical Standing Seam manufactured at both sides of the panel. Snap-on connector to interlock the panels shall have a grip-lock double tooth locking mechanism Panel shall in fixed on M.S. Structure with Aluminum Extruded Single Piece Cleats in which 3 Self Drilling SDST Screw will be applied to handle best Up Lifting Pressure. Panel shall be co-extruded UV protected. The full system shall be fitted on MS purlins perpendicular to direction of sheeting with purlin spacing as specified by Manufacturer.7000N Tested as per ISO 6892:1998 and IS 1608:2005, as per design requirement. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheet which have been exposed to UV for a min of 500 Hours as per ASTM G155. Panel shall not have Yellowness Index as per ASTM D1925 of 15 units when tested on samples exposed to UV for 500 Hours as per ASTM G 155. U Value shall not be more than 1.9 W/m2K as per EN ISO 10077-2 :2018. Polycarbonate Panel Ends shall be closed with Aluminum U profile /F Profile as and when required. The rate includes cost of all the operations, labour and all materials involved such as bolts nuts and screws etc. and labour for cutting bending to required profile. Work complete for at all floor, all level, all depth, all Height, all lead and lift etc. work complete as per the Detailed specification, shop drawing , approved sample, instruction of Architect/EIC. Sample mock shall be approved from Architect/EIC. Roof plan area shall be measured for payment. (Note: MS Fabrication and steel work paid separately in KG)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class teak wood (Staircase)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore: Horizontal

25 mm nominal bore: Vertical

32 mm nominal bore: Horizontal

32 mm nominal bore: Vertical

40 mm nominal bore: Horizontal

40 mm nominal bore: Vertical

50 mm nominal bore: Horizontal

50 mm nominal bore: Vertical

80 mm nominal bore: Horizontal

80 mm nominal bore: Vertical

Supplying and erecting approved make Instantaneous type water heater with 3Itr.capacity rust free container housed in ABS plastic body insulated with glass wool / puff insulation and 3 Kw heating elements,adjustable thermostat 300 C to 850 C with set to operate at 850 C (+ /-60 C ) auto reset indication lamps, thermal cut-out, safety valve fusible plug etc. Premium Category (Racold,A.o.Smith,Venus)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 450 mm dia RCC pipes.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Bell push

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

6 way (4 + 18), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of200 A tinned copper bus bar, common neutral link, earth bar,din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door

8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole and neutral

Triple pole

Triple pole and neutral

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB) having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 A

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (B) 3 core 4 Sq. mm

(C) 3 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. (E) 3 core 16 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core)

(F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 4 core 2.5 Sq. mm

(B) 4 core 4 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. (B) 3 core 4 Sq. mm

(C) 3 core 6 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (A) 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (A) 2 to 4 core 2.5 / 4 Sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm (45mm)

3½ X 120 sq. mm (45mm)

4 X 10 sq. mm (25mm)

4 X 25 sq. mm (28mm)

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable (B)63mm outer dia

(C))90 mm outer dia

(D)120 mm outer dia.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

speaker cable Two pair, 2-core, 1.5 sqmm

Providing & erecting Following capacity Amplifier WITH BUILT-IN DIGITAL PLAYER , MEDIUM WATTAGE PA MIXER AMPLIFIER, Built-in MP3 player with remote control for USB, SD/MMC card reader approx 2% THD ,Frequency Response :- 50-15,000Hz ±3dB Tone Controls -Bass:Treble ,Speaker Output :- 4Ω, 8Ω, 70V & 100V ,Digital Player MP3 Player with USB, SD and MMC Card Reader . (B) 120 Watts (max 160 W RMS output)

SITC of High Performance dual channel UHF wireless tie pin/ handdeld microphone available in different frequencies. Separate volume control for both channels. One handheld dynamic transmitter and one Bodypack transmitter, each operating on 2×1.5V AA pencil cells. Separate balanced audio output from each channel through XLR connector and an unbalanced mixed output through 6.3mm (¼”) jack erected as directed by enginner incharge

Providing & erecting main Distribution (MDF) indoor type, back mounted frame as per DoT standard approved with krone strips (b) Suitable for 20 pair

(d) Suitable for 50 pair

(e) Suitable for 100 pair

Supplying & erecting approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections. (2) Twenty Pairs

(3) Fifty Pairs

(4) One Hundred Pairs

SITC of company fabricated patch cords shall conform to Cat- 6 & conductor shall be stranded for better flexibility Shall support network line speeds up to 1 Gbps Shall have RJ-45 jacks. (C) 3 Mtr

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 80mm dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100mm dia

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Supply, installation, testing and commissioning of continuous duty submersible centrifugal water supply pumps complete with 3 phase motor, level sensor, control panel with all necessary protection andmechanical seal etc with Cabling upto Control Panel etc complete .Vendor to submit proposed pump model with duty curve. Flow rate : 100.0 LPM each (1 Working + 1 Standby) Head : 25 Mts Purpose : Domestic Water Transfer from Under ground Tank to Over Head Tank. Consider level sensor and control panel to operate pump automatically based on OHT water level.

Providing and fixing 5 mm thick mirror of superior glass (of approved quality) in single piece and of required shape and size fixed with second class teakwood beading or with adhesive or with two way tape (3M or equivalent Quality) with 6 mm Plwood backing complete as per the architectural drawings and the directions of Engineer-in-charge .

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

16.43 Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately

Supplying and laying 50 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 4 core 16 Sq. mm

UPS SYSTEM: Supplying and erecting approved make online Un-interruptible Power Supply system comprising flat cum-boost charger, static Inverter & sealed maintenance free SMF batteries. The charger having operating capacity for input 160-270V AC & inverter having output 230V,50 Hz Ac with 0.8 load power factor with battery, over/under voltage output with over load & short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following power backup.with MS painted batteries stand, 10% Overload capacity for momentary load. (F) 15 KVA 3 - phase with 1Hr Backup

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable (B)185 mm outer dia

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable (C)200 mm outer dia

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM. [A] 305 mm dia 900 RPM. Cat.II

Boaring/ horizontal directional drilling (HDD) for Laying, joining and commissioning of any type of cable/ services pipes without damagin surface/ road. work including survey, information collection regarding underground utilities, sensing of utilities by sensing equipment, pitmaking, pilot drilling, pre-reaming pulling the ducts of suitablesize as per the designed invert levels. The contractor has do the thorough survey of the under ground utilities before commencement of BORING/ RAMMING/ DIRECTIONAL DRILLING to avoid the damage to the other utilities. No extra payment will be made for any trail/ abandoned pits made during the survey. Bidder shall have sufficient number of standard tools & tackles and instruments require for Horizontal Drilling work, confirming relevant IS standards and the instruments shall be duly calibrated by NABL accredited lab wherever require. a) upto 300mm dia below road level without damaging the road with required.

Total Amount

Bhumi Procon Private Limited (BID ID -3166311)

BPC Projects and Infrastructure Pvt. Ltd. (BID ID -3162275)