Provn of septic tank for toilets of Gp C accn and additional sewage system for new cadet mess at RIMC, chain link fencing alround bldg No P-1 of NCC Directorate of Uttarakhand and special repair to bldg No P-116 and 117 at RIMC under GE Dehradun

Amount

Demolition of cement concrete in ground floor and paving nexc 15cm thick (below or above ground level ) and removing rubbish off the MD land complete all as specified.

M&L for PCC (1:3:6) type C-2 (using 40mm graded curshed stone aggreate), 75 mm thick as in plinth protection, finishing the surface even & fair without using extra cement the plinth protection shall be laid in alternate bays n exe 2 Sqm, 10mm joints shall be provided, joints shall be filled with bitumen mastic, bitumen mastic comprise of 1 Part of Hot bitumen 85/25 grade and 3 parts of sand all by weight complete all as specified & directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust,etc complete all as specified and directed.

M&L for 25 mm thick cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in sub base for laying floors, tiles etc, finishing the surface fair and even complete all as specified and directed .

M&L for machine cut kota stone slabs 20-25mm thick, as in floors, shelves, steps etc, laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab, over and including 15 mm thick cement screed bed in CM (1:6) including rounding off exposed edges ,complete all as specified.

M&L for machine cut kota stone slabs 15-18mm thick, as in riser of steps, skirting, dado etc. , laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab, over and including 10 mm thick rendering in CM (1:4) ,complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed.

M & L for Vitrified Ceramic tiles light shade polished (square / rectangular) of 10mm thick, area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile including 15mm screed bed in cm 1:6 complete all as specified and directed.

M & L for Vitrified Ceramic tiles light shade polished (square / rectangular) of 10mm thick, area of each tile n.exc exceeding 0.36 sqm as in skirting/dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over 10 mm th rendering in cm 1:4, complete all as specified and directed.

M&L galzed ceramic coloured tiles of size 300mmx200mmx6-7mm thick on vertical surfaces such as in skirting, dados set and jointed in neat cement slurry and pointed in coloured cement to match over and incl 10mm thick cement plaster in CM 1:4 complete all as specified and directed.

M&L for non-skid coloured ceramic tile 300x300x 7 mm thick in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM (1:6) complete all as Spfd.

M&L for 100mm thick PCC (1:2:4) type B-2 (using 40mm graded crushed stone aggregate) as in as in paving and broom finished surface on top complete all as specified and directed.

Taking down cement plaster from brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified

M &L 15 mm thick rendering in cement mortar (1:6) in two layers (10-12 & 5-3 mm thick) on fair faces of brick work and finished even and smooth without using extra cement complete all as specified and directed.

M &L 15 mm thick rendering in cement mortar (1:4) in two layers (10-12 & 5-3 mm thick)on fair faces of brick work finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered / unplastered surfaces of wall and applying wall putty 2 - 3 mm thick and rubbing with sand paper to make the surface smooth and then applying two coat of oil bound distemper over a coat of suitable primer,complete all as specified and directed.

M&L for complete removal of existing treatment from old plastered surfaces of walls using steel wire brushes and hand held electrical grinder as directed and providing wall putty 2 to 3 mm thick and rubbing with sand paper to make the surface smooth and then applying two coat of oil bound distemper over a coat of suitable primer,complete all as specified and directed.

M&L for applying two coats of cement base paint over a coat of suitable primer on new plastered surfaces of walls including preparation of surface complete all as specified and directed.

M&L for complete removal of existing treatment from old plastered surfaces of walls using steel wire brushes and hand held electrical grinder as directed and then applying two coat of cement base paint over a coat of suitable primer,complete all as specified and directed.

M&L for preparation of plastered or un-plastered old surfaces of wall and applying on coat of weather proof exterior emulsiong paint complete all as specified and directed.

M & L for preparation of old decorated wooden surfaces over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frame) and removing from site complete all as specified and directed.

S&F factory made 100% solid wood plastic composite (WPC) door frame of size 75 mm x 50 mm x 50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof termite proof fire retardant and having good screw holding capacity all as specification and drawing complete all as specified and directed by Engr-in-Charge. Make : ECHON/Kumar Tech/Sintex

S&F 30 mm thick moulded WPC factory made 100% solid door shutter(conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire retardant and having screw holding capacity complete all as specified. Make : ECHON/Kumar Tech/Sintex

S&F 18 to 20 mm thick solid PVC board for cupboard shutters with one side 1 mm thick printed PVC sheet & other side plain PVC sheet with suitable PVC frame including taking down of old board complete all as specified and directed.

S & F 40mm width Continuous (piano) hinges, mild steel, bright finish or electrogalvanise end fixed complete all as specified and directed.

S&F mild steel butt hinges cold rolled medium weight 100mm size complete alla specified and directed.

S&F 125mm size aluminium handles, cast type, anodised complete all as specified and directed.

S&F 200 mm long, aluminium,anodised, barrel tower bolts of extruded section complete all as specified and directed.

Taking up or down 15 mm bore GI tubing and connections including cutting chases, making good to facing in cement mortar 1:3 all as specified and directed.

Taking up or down 20 mm bore GI tubing and connections including cutting chases, making good to facing in cement mortar 1:3 all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F in repair Bib taps cast copper alloy , screwed for iron pipe or for brass ferrule and fixed (15mm bore dia of pipe ) complete all as specified and directed. Make : Jaquar CON047KN/ Parryware G3304A1/ Hindware F200003.

S&F repair 15mm bore Pillar taps, cast copper alloy,, with or without lettered 'Hot' or 'Cold' , screwed for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge.Make : Jaquare Cat Part No VGP 81001/Hindware Cat Part No F370001/Parryware Cat Part NoG9802A1

S&F in repair Health Faucet with 1 mtr metalic expandable tube & hook complete all as specified and directed. Make : Jaguar model No. ALDCHR 585/ Prayag model No BEA 88/ equivalent make in Hindware/ Parryware..

S&Fin repairs 15mm dia PVC connection 450mm long incl PVC nuts complete all as specified and directed by Engr-in-Charge.

M&L in repairs for 32 mm waste fittings PTMT (half or full threaded) in basins, etc. with bedded in red lead cement and other end fixed complete all as specified and directed.

S& F 32mm PVC flexible waste pipe 800mm long suitable for WHB/ sink etc complete all as specified & directed.

S&F in repair brass chromium plated ovehead shower with shower arm complete all as specified and directed. Make : - Parryware Cat Part No T9985A1(Shower) & T-9999A1(Arm)/Hindware Cat Part No F160054 (Shower) & F190016(Arm)/Jaquar Cat Part No OHS 1999 (Shower) & SHA479L300 (Arm).

S&F in repair vitreous china wash hand basin with brackets, white, size 550 x 400 mm including CP brass 32mm waste fitting with long screwed shank and fly-nut, 32 mm PVC waste pipe including cutting for and pinning in ends of brackets complete all as specified. Make: Jaquar CNS WHT 801/ Parryware CO460/ Hindware 10010.

S&F in repair rotational moulded polyethylene water storage tanks 1000 Ltrs capacity three layered, externally white (cylindrical vertical with closed top) hoisted and fixed in position including PTMT ball valve 20mm bore with polythelene float, 20mm dia GI medium grade over flow pipe(approx lengh1.5 mtr), 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.

S&F in repairs 15mm bore Angle stop valve, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. Make: Jaquar Cat Part No FON-40053/ Hindware Cat Part No F160017/ Prayag Cat No 9410.

S&F in repair vitreous china water closet orrisa pattern 580x440 mm, white, with front or back inlet with integral 'foot rests and provn of cement concrete bedding, connecting to flushing pipe complete all as specified and directed. Make- Prayag ca No-4054/Jaguar cat No-CNS-WHT-451 / equivalent in Hindware.

S&F in repair vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) but including plastic water closet seat closed pattern with flat bottom and cover with PVC hing devise, fixing bolt for pedestal pattern complete all as specfied and directed. Make- Hindware cat No-20044/ Jaguar cat No-ECC-WHT555 N

S&F in repair 20 mm dia brass chromium plated tubular towel rack of 3 set type, 60 cm long between flanges, brackets complete all as specified and directed.Make- jaguar cat No- AKP-35781P /Prayag cat No-BA-42/equivalent in Hindware/ Parryware.

S&F in repair PVC flushing cistern 8 ltr capacity, white, valve less, syphonic action type, low level, with inlet ball valve, float, handle including PVC flush pipe, PVC connection 15mm size 45cm long with brass CP nuts, fixed with and including brackets or stainless steel screws and rawl plugs complete all as specified .

Demolition and breaking up drain pipes 100mm dia (salt glazed stone ware, AC/ PVC or reinforced concrete) jointed in cement mortar and taking out of trenches or wall if required, complete all as specified and directed.

Demolition and breaking up drain pipes 75mm dia (salt glazed stone ware, AC/ PVC or reinforced concrete) jointed in cement mortar and taking out of trenches or wall if required, complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or under floors with suitable solvent complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or under floors with suitable solvent complete all as specified and directed.

S&F PVC (SWR) bend 110 mm dia, any radius jointed with approved adhesive complete all as required and as directed.

S&F 75 mm dia PVC (SWR) multi floor trap, with CP grating including jointing to waste pipe with solvent cement and fixed in cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F 75mm dia PVC (SWR)vent cowl complete all as specified and directed.

S&F 110mm dia PVC (SWR) 'P' trap complete all as specified and directed.

S&F CP 101x101mm Square shape grating including cockrotch jali complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf with chromium plated guard and railling (with brass bracket) complete all as specified and directed. Make : Prayag Cat No BEA-44/Parryware cat No-T-6703A1/ equivalent in Jaguar/Hindware.

S&F in repair 25 mm dia stainless steel ss-304 grade drapery rod , decorative, including decorative brackets, at both ends & curtain rings 8 Nos (minimum) complete all as speccified and directed.

M&L for mild steel framed work such as grills, gratings , iron chowkhats etc., framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work mild steel conforming to Fe - 290, Gde- E 165 complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation filling / mass concrete complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description, over 10 cm width or girth, and applying two coats of synthetic enamel paint over one coat of red oxide primer of any tint complete all as specified and directed. The tint of synthetic enamel paint shall be approved by GE.

M&L for 50mm thick cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in paving/floors and providing top surface with 20mm thick wearproof topping in cm 1:2, using approved floor metalic hardner as specified and finished even and smooth ,complete all as specified and directed.(Note- Metalic floor hardner shall be measured & paid separetely under respective item of BOQ as supply only).

Supply only approved floor metalic hardner complete all as specified and directed.

Forming construction (dummy) joint , filled with plastic dividing strips 1.5mm thick and 38mm width ,complete all as specified and directed.

M&L for preparation of new concrete / plaster surfaces of floor,exceeding 10 cm width or girth and applying two coats of floor paint over a coat of suitable primer, complete all as specified and directed. Make- Indigo/Asian/Berger as approved by GE.

M&L for preparation of new concrete / plaster surfaces of floor,n.exceeding 10 cm width or girth and applying two coats of floor paint over a coat of suitable primer, complete all as specified and directed. Make- Indigo/Asian/Berger as approved by GE.

M & L for preparation of old decorated steel surfaces over 10 cm width or girth and applying one coats of synthetic enamel paint ,complete all as specified and directed.

S&F modular PVC septik tank for 100-130 users and capacity not less than 25500 ltrs,installed in position on levelled flat base and connecting to inlet (160 mm dia pipe) & outlet (200 mm dia pipe) pipes including excavation in any type of soil upto required depth, PCC (1:4:8) type D-2 in base 150 mm thick,returning filling in soil , removing surplus soil n. exe 50 meter and depositing where directed, complete all as specified and as per manufacturer recommendation/ instructions. Make: Supreme/ equivalant in Sintex as approved by GE.

M&L for construction of 2.4 M dia X 4.5 M soakage well including connection complete all as specified and shown on drawings.

M&L for construction of septic tank suitable for 50 users including connection complete all as specified and shown on drawings.

Excavation in trenches n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc, or for shafts, wells, cesspits manholes, pier holes etc. n exc 10 Sqm on plan and n exc. 1.5 mtr in depth and getting out in any type of soil complete all as specified.

Returning filling in , including spreading, leveling and watering, well ramming n.exc 25cm thick layer in any type of soil complete all as specified and directed.

Removing excavated material (Soils) to a distance not exceeding 50 mtr and depositing where directed at a level n.exc. 1.5 mtr above the starting point complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, , straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) complete all as specified. (using old size bricks)

M&L for brick work with subclass 'B' bricks, , straight or curved on plan exc 6 m mean radius built in cement mortar (1:4) complete all as specified. (using old size bricks)

M&L for brick work with sub class ‘B’ old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:4) in half brick thick wall complete all as specified and directed.

M&L for precast reinforced factory made cover slabs 60-70 mm thick M-30 grade and size as per site requirement in cover slabs for manholes etc. and similar articles with plain faces including necessary forms, moulds as required, set in cement mortar (1:4) complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) (1:1½:3) type A1 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. (Note :- Reinforcement & formwork shall be measured and paid for separately)

M & L for cement concrete ( 1:3:6 ) type C1 (using 20 mm graded stone aggregate) as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement and necessary form work, complete all as specified. (Note : Forming fair finished channel for drain using extra cement will be measured and paid for separately under respective item of BOQ.)

M&L for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitered/ stopped ends etc complete all as specified and directed.

M & L for mild steel round bars 10- 12mm dia, fixed horizontally as stiffner to the chain link fencing, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 8-10 mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work and demolition of concrete complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 ( using 40 mm graded crushed stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed.

M&L for rubber moulded pre-polished pavement coloured chequred tiles glossy finish of size not less than 300x300x20-22 mm thick with anit skid properties laid over and including 20mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L salt glazed stone ware (SGSW) drain pipe of internal dia 150mm laid in treches and jointed in CM (1:1) complete all as specified and directed.

Excavating in post holes (or similar holes) each n.exc 0.5 cum in any type of soil, getting out and removing surplus soil to a distanc n exe 50 m and making good the surface complete all as specified and directed.

S&F mild steel work as in posts and struts in fencing etc including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for cement concrete , Type C-2 (1:3:6) (using 40mm graded crushed stone aggregate) for walls, retaining walls, basement walls, ballast walls and the line including caps & bases , complete all as specified and directed.

S&F mild steel flat iron for securing of chain link fencing conforming to Fe 290 Gde E-165 including fabrication i.e. cutting tops drilling holes etc complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other end or screwed both end, each screw end to be fitted with 3 mm thick MS washers and one hexagonal/ Square exc 5cm n.exc 10cm long, dia of neck 11-15mm complete all as specified and directed.

Supply only MS galvanised chain link fencing of any dia of wire and any size of mesh , complete all as specified and directed by Engr-in-charge.

Fixing only chain link fencing of any type including line wires of standard type , rails,straing bolts etc including provision of binding wire, complete all as specified and directed.(Note- Ms straining bolts & securing rails will be measured and paid separetely under respective item of BOQ).

M&L for steel form work to soffits of suspended slab such as roof slabs, floors slabs, landing & similar work not exceeding 200 mm thick (Horizontal or sloping) etc for fair finished flat surfaces, complete all as specified & all as directed

M&L steel form work to edges of concrete flats, treads, breaks in floors, window cills, concrete raillings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide for fair finished surface complete all as specified.

R K BUILDERS

RAMAPATI ENGINEERING SERVICES

M/s Teg Singh Negi

M/s Anil Kumar