REPAIR TO ROOFING FALSE CEILING AND CERTAN B/R WORKS AT AVN BDE AND TECHNICAL AREA UNDER GE MISSAMARI

Amount

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frame)

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames)

S&F anodised aluminium frame for doors, windows, ventileters, partition with one or more rebates including joining cleat for fixing etc complete all as specified in cl power coating above aluminium section.(minimum thickness of powder coating 50 micron).

S&F anodised aluminium door shutters aluminium section weighing 0.55 kg/m including necessary joining cleats glazing clips rubber neoprene packing anodised aluminium snap beading screws, necessary locking arrangement etc complete all as specifid power coating of any colour (thickness of power coating not less than 50 micron.)

S&F for anodised Aluminium two track sliding window and ventiletor frame made up 62 mm /29.5 mm 1.5 mm thick aluminium section & shutter made up 38 mm / 20 mm/1.5 mm thick without sash bar alum section including all necessary joining cleats,hold fast ,rubber gasket anodised snap beading,anodised alumn fittings,suitable alumn handle and locking arrangment etc (thickness of power coating not less than 50 micron.) complete as directed.

S&F for anodised Aluminium three track sliding window and ventiletor frame Side/Top made up 123.45 mm /44 mm 1.5 mm thick bottom 128.00 mm/ 39.15 mm / 1.63 mm aluminium section & shutter made up 69 mm / 25.40 mm/1.63 mm and 50.80 mm / 25.40 mm/ 1.63 mm thick without sash bar alum section including all necessary joining cleats,hold fast ,rubber gasket anodised snap beading,anodised alumn fittings,suitable alumn handle and locking arrangment , two track for glass and one track for aluminium wire mesh etc as directed by engr in charge. incu power coating of any colour(thick of power coating not less than 50 micron) & provision of AC hole as directed.

S & F 4 mm thick Sheet glass, ordinary quality and glazing with aluminium beads in squares not exceeding 0.5 Sqm in each pane

M&L for 12 mm thick pre laminated particle board, interior grade prelaminated one side with decorative choice lamination &other side balancing white lamination fixed in screws to timber frame work complete all as specified and as directed.

S&F for aluminium wire cloth with 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium stapple complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube in opening as per specification complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. .frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification complete all as specified and as directed.

S & F facroty made Second class hard wood kiln seasoned and chemically pressure treated plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F 30 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F 35 mm thick factory made Second class hard wood kiln seasoned and chemically pressure treated Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc,complete all as specified and as directed.

S&F in repair stainless steel wire cloth with 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed withstainless steel wire stapple complete all as specified and directed.

S&F aluminium alloy 250mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy and fixed complete all as specified and as directed.

S & F 75 mm long extruded aluminium alloy with galvanised mild steel Butt hinges and fixed type C-21.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section

S&F in repairs Harrison rails, mild steel, chromium plated fixed alongwith 2 Nos. of brackets, stops, rollers etc, complete all as specified and as directed.

S&F for Anodised aluminium/ GI snap grid power coated framed work of size main runner 39x24.70x0.80 mm, cross tee size 29.x24.70x0.80 mm, wall angle 22.2x22.2x0.65 mm and size of grid 605x605 mm for false ceiling all as specified with 4mm thick GI suspender complete all as specified and as directed and M & L for 4m thick Non Asbestos designed Cement E board incl two coats of distempering in one side as approved by GE of size fixed in ceiling as specified and directed Including dismantling old wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and as directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, Including dismantling old wall boards (fibre, pulp, insulation etc.) any thickness, including cover fillets.

S&F 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frames as per specifications.

S&F pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws as specified incl dismantling of old steel sheets of any description.

S&F pre painted galvatume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified incl dismantling of old steel sheets of any description.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161 1979 grade St.-240 complete all as specified,incl dismantling of old steel work of any description

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or revited, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work confirming to Fe.290. Gde-E-165

S & F in repair 110 mm bore PVC (SWR) Soil, waste and vent pipes double socketed in any length with rubber ring joints fixed in walls.

S & F 110 mm bore PVC (SWR) bends of any radius.

S & F in repair 75 mm bore PVC (SWR) Soil, waste and vent pipes double socketed in any length with rubber ring joints fixed in walls.

S & F 75 mm bore PVC (SWR) bends of any radius.

S&F 15mm bore GI tubing medium graded with all fitting and fixed complete to wall and ceiling or laid in floor including dismantling of old tube.

S&F 20mm bore GI tubing medium graded with all fitting and fixed complete to wall and ceiling or laid in floor including dismantling of old tube.

S & F in repair aluminium body door closer hydraucally regulated, designation No. 3 universal type , suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg

S&F in repairs 15 mm bore, chromium plated fancy type, Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F in repairs 15 mm bore chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S & F in repairs 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S & F Chromimum plated helth faucet shower with CP flexible pipe up 15 mm bore (ABS Body) with 1 mtr long Easy Flex tube in chrome finish complete all as directed .Make-Jaquar-Code-ALD-CHR-585

S&F in repairs 10 Ltrs. Capacity PVC flusing cistern low level slimline or equivalen make / model with all accessories.

Supply & Fix in repairs Wash down water closet (Pedestal pattern), incl Plastic water closet seat cover , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repairs Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size including cutting for and pinning ends of brackets or erecting stand, including x 32 mm dia., Waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed incl 32mm dia PVC waste pipe complete all as specified and directed.

S&F in repairs Vitreous China squatting pan "Orissa" patern size 630x450mm white with integral foot rest (Excluding flushing cistern & flush pipe)

PVC connection 15 mm bore 450 mm long

S&F in repairs brass cromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges.

S&F in repairs Brass chromium plated shower rose 125mm size

M&L for Glazed ceramic coloured tiles in vertical surfaces 600x 300x 7 mm thick set and jointed in neat cement slurry & painted in white or colour cement to match incl sreed bed 10 mm thick in CM 1:4. including dismantling of old tiles.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured including Screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes including dismantling of old tiles.

M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured including Screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes including dismantling of old tiles.

M&L Vitrified Ceramic double charged dark shade tiles 10 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured including Screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes including dismantling of old tiles.

M&L for 100 mm thick cement concrete type D-2 (1:2:4) using 20 mm graded stone aggregate as in path/hardstanding complete all as specified incl demolition of old cement concrete of any description.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40mm graded aggregate as in plinth course/sub base as directed by engineer in charge incl demolition of old cement concrete of any description.

M&L cement concrete with PCC type D2 1:4:8 using 40mm graded aggregate as in foundation, incl demolition of old cement concrete of any description.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand incl demolition of old paver block, complete all as specified and directed.

S&F 500 Ltrs. Capacity rotational moulded polyethylene water storage tanks (cylinder vertical with class top) hoisted and fixed in position all as specified including 20mm bore ball brass valves, high pressure, with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed, incl dismantling of old water tank of any description.

S&F 1000 Ltrs. Capacity rotational moulded polyethylene water storage tanks (cylinder vertical with class top) hoisted and fixed in position all as specified including 20mm bore ball brass valves, high pressure, with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed, incl dismantling of old water tank of any description.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top incl removing of old padding/water proofing treatment complete all as specified and directed :- (i) M&L 25 mm thick cement concrete PCC Type B0 1:2:4 using 12.5 mm graded aggregate as levelling course. (ii) Screed bed or bedding layer 10 mm thickin CM 1:4 as in roof slab including preparation of surfaces. (iii) Applying one coat to the surface with water based bituminous primer blow bitumen of 85/25 or 90/15 at 1.2 Kg/Sqm incl cleaing of surfaces. (iv) APP based polymeric membrane minimum weighing 3.5 Kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 160 gms/sqm) land on primed surface as specified above by torch application. The overlap shall be minium 100 mm on the transverse direction and 75mm on longitudinal direction and sealing the joints with application on cold bitumen. (v) Applying two coat of bitumenous aluminium paint at 100 gm per sqm over the PP membrane.

M&L for brick work with burnt old size bricks built in cement mortar 1:6 straight or curved on plan exceeding 6mtr mean radius and all as directed including demolition of old brick work.

M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width Type C1 1:3 : 6 ( using 20 mm graded aggregate ) and setting in cement mortar 1:6 complete all as specified and as directed, including demolition of block masonery work.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc.

M&L rendering 15mm thick on other than fair faces of brick or concrete Surfaces in cement mortar 1:6 finished even and smooth.

M&L RCC nominal mix Type B1 1:2:4 (20 mm graded aggregate) aggregate) in columns, pillars, piers, posts,lintel, struts and the like; any thickness; above top of footings; including attached pilaster and buttresses including Demolition of Reinforced cement Concrete of any description and in any position complete all as specified and directed.

Use and waste form work to sides of pillars, posts, struts, piers, columns, lintel,beam and stanchions for rough finished flat surfaces of concrete complete all as specified.

M&L TMT Bars 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for Columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and as directed.

S & F mild steel TMT bar 5 mm dia and over upto and including 10mm dia in strrups as in including cutting, bending and binding with mild steel not less than 0.9 mm dia (annealed) all as directed complete.

Demolition of stone slabs tiles of any description or thickness in floors aprons laid bedeed and pointed in any morter etc

S&F for 20 mm thick Granite of any type cut beded and jointed with grey cement slurry and pointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete in vertical surfaces of wall incl 10 MM thick rendering in CM 1:4 Including Including Demolition of stone slabs tiles of any description or thickness in floors aprons laid bedeed and pointed in any morter and any position complete all as specified and directed.

S&F for 20mm thick Granite of any type cut beded and jointed with grey cement slurry and pointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete incl 20 MM thick bed 1:6 CM in floors Including Demolition of stone slabs tiles of any description or thickness in floors aprons laid bedeed and pointed in any morter etc

M&L for preparation of new surface of wall and applying two coats of cement base paint over a coat of primer.

Material & Labour for preparation of old wall surface applying one coat of 100% Premium acrylic exterior emulsion paint with silicone additives of required shade additives @ 1.43 litre/ 10 sqm .

M&L for preparation of new plastered surfaces of walls and applying two coats of acrylic distemper including one coat of chalk whiting on plastered surface to prepara-tory to distempering complete all as specified and directed.

M&L for preparation of old plastered/putty surfaces of walls and applying two coats of acrylic distemper including one coat of chalk whiting on plastered surface to prepara-tory to distempering complete all as specified and directed.

M&L for preparation of old decorated plastered wall surface applying One coat of oil bound distemper on wall all as specified and directed.

M&L applying a coat of 1mm thick wall care putty over plaster surface to prepare the surface even and smooth as per manufacture instruction complete all as specified and as directed.

Preparation of old painted wood surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint.

Preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described appling one coat of synthetic enamel paint.

Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described appling applying two coat of synthetic enamel paint over one coat of pink primer.

Preparation of new or previously untreated wood surfaces of any description, over 10 cm width or girth, not otherwise described appling applying two coat of synthetic enamel paint over one coat of pink primer.

S&F Solid PVC Door Frame of size 100mmx45 mm made out of 5mm wood grain colour PVC Sheet reinforced with MS Square etc.

S&F 40mm thick acoustic perforated particle sound absorption board of size 595mm x 595 mm for insulation purposes, fixed with screw to wooden/steel framed work with GI intermediate/ ceiling section of size 45mm x 15mm x 0.90 mm fixed to wall with stainless steel screw incl 50mm thick fibre glass wool to wooden/metal frames as required at site incl dismantling of old particle board complete all as specified and directed.

S&F in repair 12 mm thick Toughned glass as in hinged doors, partition automatic doors and similar work including cutting to shape, drilling holes as required incu necessary Bottom and Top latch and floor spring of approved make and two No stainless steel handles complete all as specified and directed.

S&F two layer of 6mm clear transparent DGU Toughened glass (sound proof) fixed with rubber gasket on and incl 60mm x 58mm UPVC casement frame to fixed with and including MS square tube of 60mm x 60mm of 3mm thick as on reuired as directed including two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. (Note : Rate quoted by the contractor shall deemed to inclusive of necessary scaffolding and all other necessary arrangements to fittings the glass with frame, upto 15.00 Mtr height)

M&L Vitrified Ceramic double charged dark shade tiles 10 mm thick (square/ rectangular) area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured including Screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes including dismantling of old tiles complete all as specified and directed.

S & F in repairs of viterious china wash down water couple closet size 760x635x300 mm tap distance S-220 mm.with cistern and seat cover Make-Jaquar-code-FNS-WHT-0921BS.including making good to floor.incl seat cover.

S&F in repairs vitreous china wash basin white, table top size 510x350x115mm excluding taps ,but including waste , barkets. Make Jaquar cat No FLS-WHT-0575

S&F in repairs 15mm bore angular stop cock with flange screwed down high pressure with crutch or butter fly handdle screwed both end for iron pipe complete .Make-Jaquar-Code-CON -059KN

S&F in repairs 15mm bore bib cock with wall flange copper alloy screwed down high pressure with crutch or butter fly handdle screwed both end for iron pipe complete .Make-Jaquar-Code-CON-041KN

S&F in repairs 15 mm bore Pillar Tap fancy Type CP make jaquar Code OPP-1500PM

S & F in repairs cromimum plated helth faucet shower with CP flexible pipe up 15 mm bore (ABS Body) with 1 mtr long Easy Flex tube in chrome finish complete all as directed.Make-Jaquar-Code-ALD-573

S&F in repairs chromium plated tubular towel rail,15 mm dia D type 60 cm long between flanges all as directed.Make -Jaquar code-AKP-35711P

S&F in repairs CP towel ring squre all as directed.Make : Jaquar code-CAN-1121N.

S&F in repairs soap dish holder fixed to plugs with chromium plated brass screws all as directed.Make- Jaquar(code-ACN-1131N)

S&F in repairs Corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chomium plated bracket guard & railing 45 cm long all as directed.Make - Jaquar Code-ACN-1173

S&F in repairs CP toilet paper roll holder with flap incl all necessary fittings. Make-Jaquar(Code-ACN-1151N)

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement incl dismantling of old railing. (Note : Rate quoted by the contractor shall deemed to inclusive of necessary scaffolding and all other necessary arrangements to fittings the glass with frame, upto 15.00 Mtr height)

S&F for factory made solid panel PVC moulded door shutter 28 to 30mm thick (style) with 2, 4 or 6 raised panel design with 2mm thick moduled PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specified & drawing

M.P.SUPPLY (BID ID -3121205)

MAA CONSTRUCTION (BID ID -3117263)

bkgeneralstores (BID ID -3112654)

M/S MOHANPASARI (BID ID -3131349)

RC Madan (BID ID -3122172)

Markson (BID ID -3121875)

Sunrise Enterprise (BID ID -3124451)