SETTING UP OF SWIMMING POOL COMMA GYMNASIUM AND SPORTS FACILITIES AND CAFETERIA AS A PART OF AUGMENTATION OF INFRASTRUCTURE AND FACILITIES AT INA EZHIMALA PHASE II

Amount

Total amount of Sch 'A' part-I ( Buildings/Structures)

Total amount of Sch 'A' part-II (Excavation, Earthwork & Site Clearance)

Total amount of Sch 'A' part-III (Demolition of existing structures)

Total amount of Sch 'A' part-IV (Internal Water Supply)

Total amount of Sch 'A' part-V (Internal Electric Supply)

Total amount of Sch 'A' part-VI (External Water Supply)

Total amount of Sch 'A' part-VII ( External Electric Supply)

Total amount of Sch 'A' part-VIII ( Area Drainage)

Total amount of Sch 'A' part-IX (Sewage Disposal)

Total amount of Sch 'A' part-X (Road, Path and Culvert)

Total amount of Sch 'A' part-XI (Retaining wall)

Total amount of Sch 'A' part-XII (Site Development)

Total amount of Sch 'A' part-XIII (Provisional lumpsum for diversion/ re-routing of underground HT/LT cables and water supply lines)

SCH. 'A' PART -XIV (MISCELLANEOUS B/R & E/M ITEMS) Note :- This schedule is not pre priced by MES and the pre priced rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Internal Water Supply:- Angular stop cock, chromium plated, cast copper alloy, screwed down, screwed for CPVC pipe 20mm dia bore complete all as specified Make Jaquar code No CON-059KN or equivalent of other make specified in the list of manufacturer

Concealed stop cock, long body chromium plated, cast copper alloy, screwed down,screwed for iron pipe 15/16mm dia bore for shower rose Make Jaquar code No CON screwed for iron pipe 15/16mm dia bore for shower rose complete all as specified Make Jaquar code No CON 087FTK+ALD-087FT or equivalent of other make specified in the list of manufacturer.

Low density ploythene pipe 16 mm dia (outer), metallic baided, 450 mm long suitable for cold/Hot water application complete with brass union on both sides complete all as specified

INTERNAL ELECTRIFICATION :- Point wiring using approved colour coding as per IS (Red/Yellow/Blue for phase, black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. with and including heavy duty non metalic regid PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with galvanised modular mild steel/pressed steel sunken boxes factory made (with earth dolly) duly covered with modular frame and base plate for fixing of modular switches, sockets and fan regulators etc, including one run of PVC insulated multi-stranded copper conductor 1.5 Sqmm nominal cross sectional area single core F.R.L.S. cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following:- NOTE: (i) Switches, sockets, regulators shall be measured and paid separately.

All as per item No. 18 here-in-before but for One light point controlled by one 5/6 Amps one way switch complete all as specified

All as per item No. 18 here-in-before but for One ceiling fan/exhaust point controlled by one 5/6 Amps one way switch and one fan regulator complete all as specified

All as per item No. 18 here-in-before but for One Socket outlet, three pin, 5 Amp, independent controlled by one 5/6 Amps one way switch or switch/socket combination 5 Amps, 5 pin complete all as specified

All as per item No. 18 here-in-before but for One Socket outlet, three pin, 5 Amps, controlled by by one 5/6 Amps one way switch or switch/socket combination 5 Amps, 3 pin. on the same board with other switches, sockets, fan regulators etc., complete all as specified

All as per item No 18 here-in-before but for one socket outlet three pin 16 Amps, using multi-stranded copper conductor 2.5 Sq. mm nominal cross sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. with and including heavy duty non metalic rigid PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1 983 for conduits and IS:341 9:1 976 for conduit accessories), with galvanised modular mild steel/pressed steel sunken boxes (with earth dolly) duly electroplated, covered with modular frame and base plate for fixing of modular switches and sockets etc, including one run of PVC insulated multi-stranded copper conductor 2.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for one 15/16 amps socket outlet independent board:- (NOTE: Switch and socket shall be measured and paid separately)

Supply, fixing, testing and commissioning of MCB double pole (DP) 16 A,AC 230 V,10 KA complete all as specified.

Supply, fixing, testing and commissioning of MCB double pole (DP) 25 A,AC 230 V,10 KA complete all as specified.

Supply, fixing, testing and commissioning of MCB four pole (FP) 25 A,AC 415 V,10 KA complete all as specified.

Supply, fixing, testing and commissioning of MCB four pole (FP) 40 A, AC 415 V, 10 KA complete all as specified.

Supply, fixing, testing and commisioning of MCCB three pole (3P) 63 Amps, AC,415V,16KA, ISI marked, complete all as specified. Make: legrand cat.no. 4200 03 or equivalent in other makes as specified in the list of manufacturers

Supply, fixing, testing and commisioning of MCCB three pole (3P) 80A Amps, AC, 415V,16KA, ISI marked, complete all as specified. Make: legrand cat.no. 4200 04 or equivalent in other makes as specified in the list of manufacturers

Supply, fixing, testing and commisioning of MCCB three pole (3P) 100 Amps, AC,415V,16KA, ISI marked, complete all as specified. Make: legrand cat.no. 4200 05 or equivalent in other makes as specified in the list of manufacturers

Supply, fixing, testing and commisioning of MCCB three pole (3P) 125 Amps, AC,415V,16KA, ISI marked, complete all as specified. Make: legrand cat.no. 4200 06 or equivalent in other makes as specified in the list of manufacturers

Earthing complete with galvanised steel earth plate electrode size 600x600x6.0mm thick burried directly in ground vertically in a pit of depth not less than 2.25 mtr below normal ground level with top edge of the earth plate not less than 1 .5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanised earth lead 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by GI protection pipe light grade 15mm dia connected to main earth wire on pole or control board and GI pipe medium grade 20mm bore for watering, funnel with wire mesh. PCC chamber pit in PCC 1:3:6 type C-1 , 40 mm thick precast RCC M-25 (design mix) cover reinforced with 8 mm dia TMT bars @ 10 cm C/C on both sides and handle, excavation and earth work in any type of soil and removal upto 50 m complete all as specified and shown in electric plate No.03 of SSR Part-I(2009), connecting to earthing test point all as specified including testing on completion.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified

Submain wiring with 2 run of 2.5Sqmm two single core (for phase and neutral) using multistranded copper conductor PVC (FRLS) insulated unsheathed with and incl 2.5Sqmm insulated unsheathed PVC insulated multistranded copper conductor as earth continuity conductor connected to common earth dolly drawn in PVC concealed conduit not less than 20mm dia heavy duty ISI marked with accessories complete all as specified (Note: 03 runs of 2.5Sqmm and one run of PVC concealed conduit shall be measured as one run only)

Submain wiring with 2 run of 4Sqmm two single core (for phase and neutral) using multistranded copper conductor PVC (FRLS) insulated unsheathed with and incl 4Sqmm insulated unsheathed PVC insulated multistranded copper conductor as earth continuity conductor connected to common earth dolly drawn in PVC concealed conduit not less than 20mm dia heavy duty ISI marked with accessories complete all as specified (Note: 03 runs of 4Sqmm and one run of PVC concealed conduit shall be measured as one run only)

Submain wiring with 2 run of 6Sqmm two single core (for phase and neutral) using multistranded copper conductor PVC (FRLS) insulated unsheathed with and incl 6Sqmm insulated unsheathed PVC insulated multistranded copper conductor as earth continuity conductor connected to common earth dolly drawn in PVC concealed conduit not less than 25mm dia heavy duty ISI marked with accessories complete all as specified (Note: 03 runs of 6Sqmm and one run of PVC concealed conduit shall be measured as one run only)

Submain wiring with 4 run of 10Sqmm four single core (for phase and neutral) using multistranded copper conductor PVC (FRLS) insulated unsheathed with and including 10Sqmm insulated unsheathed PVC insulated multistranded copper conductor as earth continuity conductor connected to common earth dolly drawn in PVC concealed conduit not less than 32mm dia heavy duty ISI marked with accessories complete all as specified and directed. (Note: 05 runs of 10Sqmm and one run of PVC concealed conduit shall be measured as one run only)

Supply, fixing, testing and commissioning of 4 feet 20W LED surface mounted battern type luminaire, luminaire lumen output of 2000 lumens, luminaire efficacy > 120 lm/W with an operanting voltage range from 140 V - 270 V. The luminaire shall have a white CRCA housing with a poly carbonate diffuser to provide uniform light and a sleek design. The luminaire shall have a CCT of 6500K , CRI > 80, power factor >0.95, SDCM < 5, THD <10% and 50,000 burning hours as per L70B50 criteria. The luminaire shall have flicker content <5% and shall have high and low cut off with auto restart feature. The luminaire shall be EMI/ EMC compliant and shall have a internal surge protection of 4 kV. The luminaire shall have Class - 1 Electrical Insulation, Class - B Serviceability (The driver can be replaced at site level). The luminaire and driver shall be BIS aprroved with "R" number mentioned and test certificates of LM79 and LM80 reports from NABL accredited labs. Make : Philips model No. BN308 LED20S 6500 L120 PSU WH or equivalent in other makes as specified in the list of manufacturers

Supply, fixing, testing and commissioning of decorative Ultra slim linear 9/10 W, 2 feet LED lighting fixture with extruded Aluminium heat sink, environmental friendly, energy efficient prewired with lamp, AC, 230V, ISI marked, complete all as specified. Make : Philips model No. BN021C LED 10S-6500 or equivalent in other makes as specified in the list of manufacturers

Supply, fixing, testing and commissioning of square type surface mounted light fitting 12W LED, with extruded Aluminium heat sink, environmental friendly, energy efficient prewired with lamp, AC, 230V, ISI marked, complete all as specified Make : philips model no.: SM 200C LED11 S 6500 PSU OD WH or equivalent in other makes as specified in the list of manufacturers complete all as specified manufacturers

Supply, installation, testing and commissioning of 31W recess mounted 2' x 2' LED luminaire with system light output greater than 3600 lumens and system efficacy >125 lm/W. The luminaire must be energy efficient with CRI>80, CCT - 6500, pf > 0.95, THD <10% SDCM<5. The luminaire shall be flicker free with a ripple content less than 5 %. The luminaire housing shall be made of CRCA and diffuser material of PS and a lifetime of 50,000 burning hours as per L70B50 criteria, 4 kV internal surge protection. The luminaire must be BIS certified and must have LM79 and LM80 reports from NABL certified labs, ISI marked, complete all as specified. philips catalogue No. RC380B LED36S 6500 G4 L60 W60 PSU ODOC or equivalent in other makes as specified in the list of manufacturers.

Supply, fixing, testing and commissioning of 40W, 4 feet LED fitting suitable for surace/ wall & conduit mounting with luminaire lumen output of 4000 lumens, luminaire efficiancy > 120 lm/W with an operanting voltage range from 140 V - 270 V. The luminaire shall have a white CRCA housing with a poly carbonate diffuser to provide uniform light and a sleek design. The luminaire shall have a CCT of 6500 K , CRI > 80, power factor >0.95, SDCM < 5, THD <10% and 50,000 burning hours as per L70B50 criteria. The luminaire shall have flicker content <5% and shall have high and low cut off with auto restart feature. The luminaire shall be EMI/ EMC compliant and shall have a internal surge protection of 4 kV. The luminaire shall have Class - 1 Electrical Insulation, Class - B Serviceability (The driver can be replaced at site level). The luminaire and driver shall be BIS aprroved with "R" number mentioned and test certificates of LM79 and LM80 reports from NABL accredited labs, ISI marked, complete all as specified. Make : Philips model No. BN308C LED40S-6500 L120 PSU WH or equivalent in other makes as specified in the list of manufacturers

Supply, fixing, testing and commissioning of smart xtra 40 W, 4 feet LED aluminium batten lighting fixture suitable for surace/ wall & conduit mounting with extruded Aluminium heat sink, environmental friendly, energy efficient prewired with lamp, AC, 230V, ISI marked, complete all as specified. Make : Philips model No. BN1 00C LED 40S-6500 PSU L1 20 GR or equivalent in other makes as specified in the list of manufacturers

Supply, installation, testing and commissioning of LED bulkhead luminaire that fits seamlessly in a variety of applications, consuming a power of 10W, lumen output greater than 700 lumens with a system efficacy > 110 lm/W. The luminaire shall housing shall be made of High Pressure diecast aluminum with a UV stablised polycarbonate diffuser, IP 66 and IK 09 protection, 2.5 kV internal surge protection. The luminaire shall have a power factor > 0.9 and shall have 50,000 burning hours as per L70 criteria. The luminaire must be BIS certified and shall have an 'R' number and shall comply all IEC safety requirements and test certificates of LM79, ISI marked, complete all as specified. Philips catalogue No. WT202 LED6S CW PSU S2 PC or equivalent in other makes as specified in the list of manufacturers.

Supply, installation, testing and commissioning of 9W LED Wall mounted mirror light Fitting, environmental friendly, energy efficient prewired with lamp, AC, 230V, ISI marked, complete all as specified. CGL catalogue No. LCL-07-CDL or equivalent in other makes as specified in the list of manufacturers.

Supply, fixing, testing and commissioning of MCB SP 6 to 32 Amps, AC, 230V, 10KA complete all as specified. Legrand catalogue No. 4085 or equivalent in other makes as specified in the list of manufacturers.

Supply, fixing, testing and commissioning of MCB 40 Amps, TP, AC, 433V, 10KA complete all as specified. Legrand catalogue No. 4086 59 or equivalent in other makes as specified in the list of manufacturers.

Supply, fixing, testing and commissioning of MCB 25 Amps, TP, AC, 433V, 10KA complete all as specified. Legrand catalogue No. 4086 57 or equivalent in other makes as specified in the list of manufacturers.

Supply, Installation, testing and commissioning of surface/recess mounting, vertical type, 415 volts, prewired, VTPN distribution board double door type of sheet steel suitable for MCCB as incomer and MCB TP/SP outgoings dust protected, duly phosphatized and powder painted, inclusive of 250 Amps tinned copper busbar for each phase, common neutral link, earth bar, din bar for mounting MCB's detachable gland/ knock out plate, and with built in loose wire box and superior make terminal connectors for all incoming and outgoing circuits, duly prewired with adequate size of FR PVC insulated copper conductor upto the terminal connector/ neutral link and ready for installation of following ways (but without MCB's and incomer) as required. - 6Way VTPN DB with metal door, complete all as specified Legrand Catalogue no.: 5077 46 or equivalent in other makes as specified in the list of manufacturers

Supply, Installation ,testing and commissioning of surface/recess mounting, vertical type, 415 volts, prewired, VTPN distribution board double door type of sheet steel suitable for MCCB as incomer and MCB TP/SP outgoings , dust protected, duly phosphatized and powder painted, inclusive of 250 Amps tinned copper busbar for each phase, common neutral link, earth bar, din bar for mounting MCB's detachable gland/ knock out plate, and with built in loose wire box and superior make terminal connectors for all incoming and outgoing circuits, duly prewired with adequate size of FR PVC insulated copper conductor upto the terminal connector/ neutral link and ready for installation of following ways (but without MCB's and incomer) as required. - 12Way VTPN DB with metal door, complete all as specified Legrand Catalogue no.: 5077 48 or equivalent in other makes as specified in the list of manufacturers

Supply, installation, testing and commissioning of ceiling fan,copper wound,1200mm sweep, 5 star rating BLDC without remote control & service value > 6.0 and in accordance with table 1 (performance value for fans) of IS 374: 2019, including fixing of down rod of any length suitable from ceiling,canopy,mounting clamp etc.AC, 230V, and connecting up complete with and including three core flexible PVC insulated multi stranded copper conductor cable of size 1.50 Sq mm from ceiling rose/ connector to fan. Note:-Rate quoted shall deemed to be included for suitable length of down rod from roof to false ceiling as directed by engineer in charge, complete all as specified. Make : Havells FUSION ES or equivalent in other makes as specified in the list of manufacturers

Supply, installation, testing and commissioning of 600mm sweep, 24" industrial type heavy duty wall mounted fan, AC, 230V, complete all as specified. Make : Almonard - Air circulator wall 24" or equivalent in other makes as specified in the list of manufacturers

Supply, installation, testing and commissioning of heavy duty exhaust fan, electric single phase AC 230 Volts, Copper wound, 450mm Sweep,1400 RPM air delivery not less than 6120 cu.mtr/min connect to ceiling rose all as directed, complete all as specified. Make : Almonard 18" or equivalent in other makes as specified in the list of manufacturers

Supply, installation, testing and commissioning of exhaust fan, electric single phase AC 230 Volts, Copper wound, self opening louvers complete 250mm Sweep , air delivery not less than 720 cu.mtr/min connect to ceiling rose all as directed, complete all as specified. Make : Crompton Greaves model Brisk Air 10" or equivalent in other makes as specified in the list of manufacturers

Supply and fixing of modular TV socket 1 module including modular plate, metal flush box, complete all as specified. Make : Legrand Cat. Part no. 673050 or equivalent in other makes as specified in the list of manufacturers

EXTERNAL WATER SUPPLY :- SWIMMING POOL - ELECTRO MECHANICAL EQUIPMENTS (Olympic size)

TOTALLY ANTI-CORROSIVE Bobbin Wound filter, 2000mm diameter. Fitted with pressure gauge panel manual air bleeder, water drain and emptying plug. fitted with collector arms and diffuser made from unplasticized PVC and polypropelene with all accessories required. Filtration velocity 40m3/hr/m2. Max. working pressure : 2.5 kg/cm2. Flow rate = 125m3/hr. Connection size: 140mm. Height: 2040mm, Filter bed: 1m (3 for swimming pool + 2 for diving pool). Valve Battery Manifold made in PVC with flanges for connecting to filters as per DIN 2501 standards. Consists of set of 5 - buttterfly valves for carrying out filtration, backwashing, rinsing and shut down of the filters. Size : 140mm . Valve battery supports made in Zinc Plated Steel. Height: 2.30m (02 Nos each per filter) Support Brackets : 2 Support Brackets with anti-vortex clamps and fixing screws For 140 mm dia pipe. First filling of multigrade 4 layer filter media sand qty as recommended by manufacture of pressure filter (0.6-1.25 mm,2.5 mm, 9-18 mm,20-40mm). NOTE : Filter media (sand/pebbles) shall be measured and paid separately under relevant item given here-in-after.

RECIRCULA TION PUMP : Cast Iron Pumps 3000 r.p.m. Mechanical Seal in Stainless Steel. I.P.-54 motor protection. Stainless steel AISI-420 shaft. With stainless steel AISI-316 strainer basket. Conn. PN-16 according to DIN2501. Flowrate : 125m3/h @ 12m.head. Electric motor Suitable HP working on Voltage 415 V+.10%, 3 Phase with Flange and adaptor 110mm dia including foundation, and connection with control panel by using 3core 6 Sqmm copper cable,fabrication work for suction and delivery header pipe with ncessary welding FRP coating complete . (3 working and 1 standby - 4 Nos for swimming pool) +(2 working and 1 standby for diving pool). NOTE : Cable from motro control panel to pump set shall be measured and paid separately.

CHEMICAL DOSING SYSTEM FOR POOL ACID AND CHLORINE : Membrane Dosing Pumps Electronic dosing pump to be mounted both on its base as well as hung on the wall. Pumps following CE regulations. IP- 65 protection. Power connections : 220/240V, 50/60 Hz. The materials in contact with liquid are :Ploypropylene, Viton, Teflon and PVC. Includes anti-acid plastic case. Operating panel protection provided by a transparent polycarbonate cover. Lubrication not required. Flow 20l/hr @ 5 bar Model: EXACTUS (Astral) or equivalent. Semi transparent polyethelene tank with external scale so that levels can be checked easily, capacity of tank 500 Ltrs capacity Agitators : agitators for easy installation in the tanks,provided with steering grip in bakelite,rod and propellor arms in PVC,length of stirring rod 900mm

POOL BASIN EQUIPMENT : Drain grille in SS 304. 500mm x 500mm Flow: 136m3/hr

Inlet: 3" adjustable pool floor return inlet made of white ABS plastic. Suction. Flow rate adjusted by turning the grille. Suction surface area: 0.015 m2. Outer 0 295 mm wall. Flow rate (0.4 m/s) 20 m3/h. Max. recommended flow rate compliant with standard EN 13451-1: 26 m3/h (0.5 m/s.) – (20 + 14Nos)

Overflow Grating made in white, U.V. Stabilized PP of 295mm width and 35mm height for swimming pool and diving pool

Overflow grating support profile made in plastic, suitable for 35mm high grating supplied in 2 metre length

Corner grating 900 for overflow channels 295mm width, 35mm height, made up of white, injection moulded copolymer polypropylene

Overflow gutter drain fitting with body and grille in ABS and screws S.S. Connection 2" dia

Suction inlet : Suction inlet in ABS with cap internal thread of 1 1/2" dia and external thread 2"

Wall conduit : ABS wall conduits 300mm long

UNDERWATER ILLUMINATION : Underwater LightsLED 13/14 W ,12V white with Niche made of pool grade , anti UV treated ABS,self adhesive eleastomer seals, IP-X8 , J unction Boxes, made in ABS, composed of 3 entries 3/4" or PG-16 coupling, Cable Conduit Hose, Flexible 1 mt. long conduit for conn. light to junction box. 3/4" and PG-16 threaded ends , Transformers 300VA with protectionwith multi out put tappings with Transformer protection boxes Made of zinc plated steel plate, painted finish complete – ( 50+ 14 Nos).

Supply of multigrade 4 layer filtermedia sand - Approximate 4250 Kgs media for one filter (0.6-1.25mm - 2900 Kgs, 2.5mm - 750 Kgs, 9-18mm - 2450 Kgs, 20-40mm - 150 Kgs) (Total 6250 x 5 = 31250 Kgs)

MAINTENANCE ACCESSORIES

Supply , testing and commissioning suction sweeper suitable for Olympian swimming pool consisting with the following which shall be measured and paid separately under relevant items given here-in-after : (a) Pump trolleyfor stand-alone pool cleaners. Made of anodized aluminium tube and a 460 mm x 370 mm plastic platform. Face plate in AISI-304 stainless steel. Starter and cable (b) Cartridge Filter. Made in PVC with transparent Polycarbonate lid. Cartridge in Polyester fabric. Connections 1 1/2".Surface filtration 4.6 m3. Flow rate 10,000 l/h (c) Monoblock Pump - 3 HP / Single phase. Supply of Pump. body and support in heat resistant plastic. Shaft with Noryl Impeller. Large capacity strainer. SS-316 shaft. 3000 rpm (d) Metallic vaccum head in polished Al and chrome bronze 1.5" length 442mm. (e) 2" length 800mm with Trailing cable (f) Extensible handles for cleaning attachments in anodized aluminium which can be adapted to the entire range of cleaning equipment, brushes, leaf skimmers and scoops.10.0mts. Long with Handle adaptor (g) Floating suction hose Made of blue polyethylene. Includes terminals, except in the 30-m hose. 0 38 mm (1 1/2”] 30 m (h) Shark leaf skimmers - wing-nut or wishbone fixing. Shark deep water leaf skimmer (j) Surface net made in polypropelene and white. polyester netting Shark (k) Shark brushes - wing-nut or wishbone fixing. Shark special bottom curved brush (l) Straight brushes made in polypropelene for pool. basins and scum liners, Shark (m) Classic brushes - wing-nut fastening. Classic S.S. bristle 165mm straight brush

Pump trolleyfor stand-alone pool cleaners. Made of anodized aluminium tube and a 460 mm x 370 mm plastic platform. Face plate in AISI-304 stainless steel including starter and cable of standard length

Cartridge Filter. Made in PVC with transparent Polycarbonate lid. Cartridge in Polyester fabric. Connections 1 1/2".Surface filtration 4.6 m3. Flow rate 10,000 l/h

Monoblock Pump - 3 HP / Single phase. Supply of Pump. body and support in heat resistant plastic. Shaft with Noryl Impeller. Large capacity strainer. SS-316 shaft. 3000 RPM

Metallic vaccum head in polished Al and chrome bronze 1.5" length 442mm.

Metallic vaccum head in polished aluminium and chrome bronze 2" dia, 800mm length with trailing cable suitable for pool pumps.

Extensible handles for cleaning attachments in anodized aluminium which can be adapted to the entire range of cleaning equipment, brushes, leaf skimmers and scoops.10.0mts. Long with Handle adaptor

Floating suction hose of size 38mm (11/2") dia, 30 metre length made of blue polyethylene including terminals and coupling at both ends complete suitable for pool pumps

Shark leaf skimmers - wing-nut or wishbone fixing. Shark deep water leaf skimmer

Surface net made in polypropelene and white. polyester netting Shark – 1 No

Shark brushes - wing-nut or wishbone fixing. Shark special bottom curved brush – 1 No

Straight brushes made in polypropelene for pool. basins and scum liners, Shark – 1 No

Classic brushes - wing-nut fastening. Classic S.S. bristle 165mm straight brush

Free chlorine and pH Pool tester. Chlorine range: 0.5-6.0 mg/l &ph range: 6.8-8.2. with necessary fitments and 100 ml testing solution in Rexene finished box

Control and Regulatory valve

Butterfly Valve dia 140 mm (Filtration Pump Del-7, Inlet-5, By Pass-1). Including flange adaptor

Butterfly Valve Dia 160 mm (Filtration Pump Suc-7, Drain-3, BT Suction-5, BY Pass-1).including flange adaptor

Wafer check valve of size 140mm dia with flange and adaptor ( Filteration delivery-7)

Wafer check valve of size 160mm dia with flange and adaptor ( BT suction -5)

PLUMBING

Class K-9, 150 mm (6”) dia DI pipe with spigot and socket ends, centrifugally cast suitable for Tyson joint with and including rubber tyton joint ISI marked complete all as directed. NOTE: Earth work shall be measured and paid separately

DI pipe of 100 mm dia, class K-9 with spigot and socket ends, centrifugally cast suitable for Tyson joint with and including rubber tyton joint ISI marked complete all as directed. NOTE: Earth work shall be measured and paid separately

DI fittings of any size up to 200 mm dia such as Tee, spigot, bend, socket etc as per site requirement including joints complete

10KG/cm2 Pipe UPVC Grey pipes 32mm dia and PN-16 Heavy fittings (ISI) glue joint Between swimming pool and plant room for recirculation including puddle flanges, fabrication works etc.,(Assuming 3m distance from to Pool to Plant room. Make : Supreme / Finolex or equivalent complete all as specified.

All as per item No 94 here-in-before but 50 mm dia

All as per item No 94 here-in-before but 63 mm dia

All as per item No 94 here-in-before but 75 mm dia

All as per item No 94 here-in-before but 90 mm dia

All as per item No 94 here-in-before but 110 mm dia

All as per item No 94 here-in-before but 140 mm dia

All as per item No 94 here-in-before but 160 mm dia

6KG/cm2 200mm dia Pipe UPVC Grey pipes and PN-16 Heavy fittings (ISI) glue joint Between swimming pool and plant room for recirculation including puddle flanges, fabrication works etc.. Make : Supreme / Finolex or equivalent complete all as specified.

Rubber mat of 1 metre x 2 metre x 10mm size, ISI marked

Rubber mat / PVC hand gloves to handle chemical/ liquid

Rubber boot/ PVC gum boots to handle chemicals/ liquid

Supply, install, commissioning , testing Ionizer plant of capacity 200 grms per hour approximately (specification suitable for Olympic Pool capacity 500 Cu mtr per hour) PP ion chamber 03 Nos with 08 pairs per cell of silver+copper electrodes in each chmber size 315 x 300 mm, control unit microprocessor based with voltage and current LED displays, meters, automatic polarity reversal with indication, cables up to 03 mtr to connect with chamber all enclosed in CRCA sheet, MS powder coated cabinet 16 SWG including control panel for IONIZER equipments with electric wiring & cabeling and all other accessories to run the system etc as per specification .Make IONEXCHANGE

Supply, install, commissioning , testing Ionizer plant of capacity 100 grms per hour approximately (specification suitable for Diving Pool capacity 250 Cu mtr per hour) SS 304 ion chamber 02 Nos with 04 pairs per cell of silver+copper electrodes in each chmber size 315 x 300 mm, control unit microprocessor based with voltage and current LED displays, meters, automatic polarity reversal with indication, cables up to 03 mtr to connect with chamber all enclosed in CRCA sheet, MS powder coated cabinet 16 SWG including control panel for IONIZER equipments with electric wiring & cabeling and all other accessories to run the system etc as per specification .Make IONEXCHANGE.

EXTERNAL ELECTRIC SUPPLY

Design, Fabrication, Supply, Erection,Testing and commissioning of following Powder coated Panel fabricated out of 2mm thick for indoor panel and 3 mm for outdoor panel CRCA sheet steel in cubical compartmentalised, free standing floor mounted on a base frame, totally enclosed, extensible type dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. The general construction shall confirm to IS:8623/93. Cable gland plates shall be provided on top as well as bottom of the panels with minimum 3mm thick plate. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3- Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels. Approval of GAD along with BOM shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanize and Zinc passivated). Ingress protection shall be IP54 minimum for indoor use and IP 66 for out door purpose. Complete board shall be factory fabricated and ready for installation at site. After the fabrication and before the despatching, the panel should be tested for high voltage test at 2.5 kV, insulation resistance test by 1000V megger, polarity test, Power and control circuit's continuity test , operational test before the Engineer-In charge/nominated person.

(a) Main LT Panel: Supply, installation, testing and commissioning of Main LT Panel (Outdoor type), CPRI approved with with CRCA Sheet steel 3mm thick outdoor type cubical type compartmentalised, having busbar capacity 1000 Amps, ammeter with CT's, voltmeter, indicating lamps with and following breakers as incoming and Outgoings. Incoming : 4pole ACB 630Amps,415V,50HZwithbreakingcapacity50KA,O/CandE/Fprotection-01no. Outgoing: 4 pole MCCB 160 Amps, 415V, 50HZ with breaking capacity 35KA, O/C and E/F protection - 01 no., 4 pole MCCB 125 Amps, 415V, 50HZ with breaking capacity 35KA, O/C and E/F protection - 02 Nos., 4poleMCCB100Amps,415V,50HZwithbreakingcapacity35KA,O/CandE/Fprotection- 02 Nos., 4 pole MCCB 63 Amps, 415V, 50HZ with breaking capacity 35KA, O/C and E/F protection - 02 Nos., complete all as specified.

(b) Cafeteria Feeder pillar (Outdoor type) : All as per 109 here-in-before but with the following :- INCOMER - TPN MCCB 125 Amps, 415V, 50HZ with breaking capacity 36 kA having thermal magnetic releases for S/C, O/C, releases, IDMTL Protection for S/C, O/C releases with front drive kit - 01 no. METERING & INDICATION - 1 set of phase LED indicating lamps, 1 Set of Breaker ON-OFF-TRIP indication Lamps, BUS BAR:- 1 Set of 200 Amps, TPN Aluminium bus bars with colour coded sleeves. OUTGOINGS - TPN MCCB 125Amps, 415V, 50HZ with breaking capacity 16KA - 01 no. TPN MCCB 63Amps, 415V, 50HZ with breaking capacity 16KA - 02nos. with Thermal O/L and Magnetic S/C Protection and suitable extension of breaker terminals, with front drive kit complete all as specified. Each set – 01

(c) Gymnasium Feeder pillar (Outdoor type) : All as per 109 here-in-before but with the following :- INCOMER - TPN MCCB 125 Amps, 415V, 50HZ with breaking capacity 36 kA having thermal magnetic releases for S/C, O/C, releases, IDMTL Protection for S/C, O/C releases with front drive kit - 01 no. METERING & INDICATION - 1 set of phase LED indicating lamps, 1 Set of Breaker ON-OFF-TRIP indication Lamps, BUS BAR:- 1 Set of 200 Amps, TPN Aluminium bus bars with colour coded sleeves. OUTGOINGS - TPN MCCB 80Amps, 415V, 50HZ with breaking capacity 16KA - 01 no. TPN MCCB 63Amps, 415V, 50HZ with breaking capacity 16KA - 02nos. with Thermal O/L and Magnetic S/C Protection and suitable extension of breaker terminals, with front drive kit complete all as specified. Each set - 01

Swimming pool Feeder pillar (Outdoor type) : All as per 109 here-in-before but with the following :- INCOMER - TPN MCCB 160 Amps, 415V, 50HZ with breaking capacity 36 kA having thermal magnetic releases for S/C, O/C, releases, IDMTL Protection for S/C, O/C releases with front drive kit - 01 no. METERING & INDICATION - 1 set of phase LED indicating lamps, 1 Set of Breaker ON-OFF-TRIP indication Lamps, BUS BAR:- 1 Set of 300 Amps, TPN Aluminium bus bars with colour coded sleeves. OUTGOINGS - TPN MCCB 100Amps, 415V, 50HZ with breaking capacity 16KA - 01nos, 63 Amps-02nos. with Thermal O/L and Magnetic S/C Protection and suitable extension of breaker terminals, with front drive kit complete all as specified. Each set – 01

Supply, installation, testing and commissioning of DG, LT panel board (Outdoor type) IP65 made of modular polycarbonate thermoplastic enclosures shall be environment friendly recyclable, UV resistant, halogen and silicon free, anti acid and anti corrosive. The gasket materials shall be polyurethane and shall be internally embedded, having busbar capacity 63 Amps, ammeter with CT's, voltmeter, indicating lamps with and following breakers as incoming and Outgoings. Incoming : 4 pole MCCB 40 Amps, 415V, 50Hz with breaking capacity 25KA, O/C and E/F protection - 01 No. Outgoing : DP MCB 16 Amps, 50 Hz, 415 V with rupturing capacity 10 KA - 5 nos., 4 Pole MCCB 16 Amps, 50 Hz, 415 V with rupturing capacity 16 KA - 1 no. complete all as specified.

Supply, installation, testing and commissioning of street light feeder pillar (Outdoor type) IP65 made of modular polycarbonate thermoplastic enclosures shall be environment friendly recyclable, UV resistant, halogen and silicon free, anti acid and anti corrosive. The gasket materials shall be polyurethane and shall be internally embedded. with incomer 16amps TPN MCB with dual sensor (LDR and astronomical timer, Legrand cat. no. AlphaRex3 D21 astro or equivalent) to regulate 'ON' 'OFF' with contactor required MCB and IP66 protection incoming switch shall have front drive kit) with 9nos 6Amps DP MCB 10kA and 1no. 10 Amps DP MCB 10kA for outgoing.

Earthing complete with galvanised steel earth plate electrode of size 600mm x600mmx6.0 mm thick burried directly under ground vertically to a depth not less than 2.25 meter below ground level with top edge of the plate at a depth not less than 1.5 m below ground level connected to and including galvanised strip 32 x 6mm, by means of bolts, nuts, check nuts and washeres made out of GI including protection pipe GI light grade 40 mm size and watering pipe 20 mm dia GI medium grade all as shown on plate No 3 of SSR Part-I, connecting to earthing test point, including necessary earth work in any type of soil, PCC earth chamber made in PCC 1:3:6 type C1 (using 20mm graded aggregate), common salt, charcoal, CI funnel, earth pit cover in RCC 1 :2:4 type B1 (using 20mm graded aggregates), with 8mm CTD bars @ 140mm c/c in both ways, including necessary form work complete including necessry test on completion all as specified and as directed.

Supply, laying, testing and commissioning of cable XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 2 core 4 sqmm including cable glands and complete all as specified.

All as per item No 119 here-in-before but for XLPE cable of size 2 core 6 Sqmm

All as per item No 119 here-in-before but for XLPE cable of size 4 core 10 Sqmm

All as per item No 119 here-in-before but for XLPE cable of size 4 core 16 Sqmm

All as per item No 119 here-in-before but for XLPE cable of size 3.5 core 25 Sqmm

All as per item No 119 here-in-before but for XLPE cable of size 3.5 core 35 Sqmm

All as per item No 119 here-in-before but for XLPE cable of size 3.5 core 50 Sqmm

All as per item No 119 here-in-before but for XLPE cable of size 3.5 core 70 Sqmm

All as per item No 119 here-in-before but for XLPE cable of size 3.5 core 120 Sqmm

All as per item No 119 here-in-before but for XLPE cable of size 3.5 core 185 Sqmm

Supply and fixing of steel tubular swaged poles Type 410SP-22 (8.5 meter long) Swan Neck Type complete with CI base plate and finial tapper plug, bolts, nuts and washers and single swan neck, including 3 coat of bitumen paint internally complete and externally for the portion embedded in concrete and two coats of aluminium paint over a coat of red oxide primer to the balance portion of external surface and all as specified and directed. Note : Excavation and PCC shall be measured and paid seperately under relevant item of schedule 'A' foundation andcoping.

Supply, installation, testing and commissioning of LED street light fitting 45/46W with system efficiancy greater than 120 lm/W and system lumen output greater than 3600 lumens, CRI >70 , CCT-5700 K , pf>0.95. The luminaire shall be made of die-cast aluminium housing and toughened shatter proof lens with unique road optics nad finless design. The luminaire must have a IP66 protection and IK07 protection, 4kV internal surge protection. The luminaire must have feature for auto high cut off @ 325 ± 15V & Auto Restart. The luminaire must be BIS certified and must have LM79 and LM80 reports from NABL accredited labs. The cost shall include all accessories and suitable bracket including connecting from terminal box to fitting with 3 core 1.5sq.mm flexible copper wire in PVC flexible conduit, etc., and tesing on completion all as specified and directed.Make:CROMPTON model:NEXUS+ LSTP-45-CDL or equivalent) or equivalent in other makes as specified in the list of manufacturers

Riddled soil as earth cushioning to UG cable by using IS sieve to separate the composite particle/roots etc and refilling/spread in trenches as cushioning and rammed down to form a solid bed all as specified in SSR Part I, Clause 19.75 and as directed. Note:-1.Punned thickness shall be measured and paid seperately. 2.Excavated approved soil shall be riddled by using sieve to separate composite particles etc as per IS.

Supply and fixing terminal box, pole mounted made out of polycarbonate IP66 with MCB SP 6Amps and connection of size 255x205x112mm for street light fitting complete all as specified and as directed. Make :Hensel or equivalent in other makes as specified in the list of manufacturers.

Supply and fixing of solar all in one LED street lighting - smart integrated solar street light with build in Poly Crystalline Panel, lithium ferro phosphate (LiFePO 4) battery, MPPT charge controller and PIR sensor and 6mtr height pole, complete all as specified with system wattage not more than 1x45W and system lumens >= 4500. The luminaries shall be with operating voltage 140-270V with PF > 0.9. The LED shall be of SMD type only with CCT 5700K CRI >70. The luminaries shall be with IP 65 and Electrical protection Class I. The luminaire shall have an efficiency > 175 lm /W. Solar cell efficiency of min 12%, polycrystalline, solar panel module capacity of 12V, 60W peak, integrated MPPT charger with driver. Charger and driver efficiency of greater than 90%. Luminaire housing shall be aluminium pressure die cast and the front cover shall be UV stablized polycarbonate cover. Lumianire shall have inbuilt PIR sensor. Luminaire shall have compatible for tilt angle fo 0 - 15 degree adjustable, arm & pole mount. outer mounting dia of 48 - 60mm. Lumianire shall have IES compliance of IEC60598, IEC 62109, 50530, 61547, CISPR 15, IEC62133, 61960, UL1642 for safety of lithium ferro phosphate battery, IEC61730, 61215 for solar panel.. The luminaire must be BIS certified. Philips catalogue no. BRP710 LED45 CW MR S1 12V LFP Solar IN or equivalent in other makes as specified in the list of manufacturers.

Supply, installation, testing and commissioning of 60W LED flood light fitting, the flood light luminaire shall have SMD type LED confiduration made up of Pressure die cast housing from ADC12 aluminium alloy with very low copper content and integrated optics confirming to IP66 and impact resistance IK08 with a system level lumen outputof8,200lumensandaluminousefficacygreaterthan110lm/WTheluminaireshallcorrespondtoacolor temperature of 5700 K with a CRI >70. The luminaire shall have a high cut off at 325 V +/- 15 V and auto restrart immediately when the voltage comes back to the operating range. The luminaire shall have a lifetime of 50,000 burning hours as per L70B50 criteria, power factor > 0.9, THD <10% at full load . The luminaire shall have a 4 kV internal surge protection, Class - 1 Electrical Insulation, Class - B Serviceability (The driver can be replaced at site level). The luminaire and driver shall be BIS aprroved with "R" number mentioned and test certificates of LM79, complete all as specified. Make: Wipro catalogue no.LF19-711-060-57-XX or equivalent in other makes as specified in the list ofmanufacturers

Supply and installation and commissionint of 11 W LED bollard light fittings complete all as specified. Make Wipro Cat No LB14-131-xxx-65-08 or equivalent

Light grade GI tubes 25mm bore, with all fitting; laid in trenches/on floors/walls/across drains for protection of UG cable complete all as specified

Galvanized high mast system with its accessories of 16metre height. Mast shall be in two sections, hot dip galvanized with 3 mm section thickness, top dia 150 mm, bottom dia 340 mm,and suitable for wind velocity as per IS 875 Part 3. It shall also include accessories for high mast including head frame, steel wire rope 6mm dia (7/19 construction) double drum winch, galvanized lantern carriage arrangement suitable for 6 luminaires symmetrically & its control gear boxes and lighting finial . The mast shall have an integral power tool installed inside the base compartment for its operation complete all as specified and for including the followings :- (a) Foundation bolts manufactured from special steel along with nuts, washers, anchor plates & templates - 01 No. (b) Floodlightluminaire150WLED,5700K,Wipromake-Catalogueno.LF20-192-060-57-G2 or eqivalent - 06 Nos (c ) LED type aviation obstruction lights -01No (d) Single point air termination aluminum rod 12 mm dia 300 mm long with aluminum base plate of size 125 x 125 x 175 x 10 mm fixed on hylum sheet of size 175x175x10 mm and fixed on top of high mast for lightening arrestor and connecting to an independent earth with a test point by 10 Sq mm PVC Insulated Copper Conductor - 01Job. (e) Control panel housing suitable control circuit for the operation of the mast. It shall also consist of suitable control for the power tool motor -01No (f) Design and casting of suitable hard rock foundation with M-20 concrete for the high mast considering the safe soil bearing capacity at site as 10T/Sqmt at 2 metre depth - 01No (g) Erection and commissioning of the high mast with the help of suitable equipment-01Job (h) GI strip 32/6 mm earthing station for high mast (2 per mast is mandatory, 01 for lighting arrestor and 01 for electrical - 02No

HIGHBAY LIGHTS : Supply, fixing, testing and commissioning of 220W LED Highbay fittingl, LED with SMD type LED configuration made up of pressure die cast housing from ADC12 aluminium alloy with very low copper content and integrated optics confirming to IP66 and impact resistance IK08. The luminaire shall have a lifetime of 50,000 burning hours as per L70850 criteria, power factor > 0.9, THD < 10% at full load. The luminaire shall have a 4 KV internal surge protection, Class-1 Electrical Insulation, Class - B Serviceability (The driver cazn be replaced at site level). The luminaire and drier shall be BIS approved with "R" number mentioned and test certificate of LM 79 and LM80 reports shall be submitted, ISI marked. The cost shall include suitable fixing arrangement for light fittings on trusses/ ceiling including wiring from light fittings to termination with suitable cable complete all as specified. Make - Philips model No. BY415P LED2755 CW PSU GR FG NMB/CG Model No LHB11-200-CDL/60-M or equivalent in other makes as specified in the list of manufacturers

HIGHBAY LED LIGHT FITTINGS : Supply, fixing, testing and commissioning of 80W LED Highbay fitting with a system efficacy >125 lm/W, and system light output greater than 10500 lumens. The luminaire shall have a rated life of 50000 burning hours as per L70B50 criteria. Ther luminaire housing shall be made of diecast aluminium and high transmittance tempered glass with PC lens. The luminaire must be able to operate from -10 deg C to 45 deg C The luminaire must meet IP66, IK08 rating with THD < 10%, PF > 0.95,with auto high cut off @ 325 ± 15V & Auto Restart, 4 kV inbuilt surge protection. The luminaire must have phase to phase protection of 440 V upto 8 hours atleast. The luminaire must be CRI>80, SDCM < 5 and a narrow beam angle. The luminaier shall have Class I protection and must be BIS certified and must have LM79 & LM80 reports from NABL accredited labs. The Cost shall include fixing arrangement for light fittings on trusses / ceiling including wiring from light fittings to termination with suitable cable complete all as specified. Make : Philips model No. BY225P LED100S CW NB PSU FG GR or equivalent in other makes as specified in the list of manufacturers

Supply, fixing, testing and commissioning of 350W LED Asymmetric light fitting, LED with SMD type LED configuration made up of Pressure die cast housing from ADC12 aluminium alloy with very low copper content and integrated optics confirming to IP66 and impact resistance IK08 with a system level lumen output of 42,000 lumens and a luminous efficacy greater than 120 lm.W The luminaire shall correspond to a color temperature of 5700 K with a CRI >70 and SDCM value <5. The luminaire shall have a high cut off at 325 V +/- 15 V and auto restart immediately when the voltage comes back to the operating range. The luminaire shall have a lifetime of 50,000 burning hours as per L70B50 criteria, power factor > 0.9, THD <10% at full load . The luminaire shall have a 4 kV internal surge protection, Class - 1 Electrical Insulation, Class - B Serviceability (The driver can be replaced at site level). The luminaire and driver shall be BIS approved with "R" number mentioned and test certificates of LM79 and LM80 reports shall be submitted, ISI marked, The cost shall include suitable fixing arrangement for light fittings on trusses / ceiling including wiring from light fittings to termination with suitable cable complete all as specified. Make : Philips model No. BVP483 P LED210 x2 AMB or equivalent in other makes as specified in the list of manufacturers.

LIGHTNING PROTECTION : Supplying, intallation, testing and commissioning of Parallel Connectors for (500mm air terminal) connecting two conductors in parallel manner. with clamping range- Rd / Rd 7-10 mm & Complied as per Standard EN 62561-1. & Air-termination rod having length- 1500 mm, of Diameter Ø 16/10 mm, Material of air-termination rod- Al, Complied as per Standard EN 62561-(1+2). Side Wall Clamp for air terminal, Clamping range - 10/16 mm. FS Clamps (Air-termination Rod Clamps 16mm) for connecting air-termination rods to roof conductor, EN 50164-1. Note : The rate includes necessary civil works, supports and all other materials required as per the recommendation of the manufacturer and testing on completion

Providing and laying of roof Conductor of Diameter Ø10 mm, Cross-section- 70 mm2, of Material- AlMgSi & Complied as per Standard EN 62561-2., Conductor holder for Parapet wall for Rd 8-10 mm Fl 20 mm, Height- 20 mm & Complied as per Standard EN 62561-4. with Universal connector with clamping range- 8-10mm, with truss head screw M10x35 mm & Complied as per Standard EN 62561-1., Expension piece & Glue for clamps.

Providing and fixing of UNI Disconnecting Clamps with intermediate plate for round and flat conductor of Material- StSt, Material thickness- 2.5 mm, with clamping range- Rd / Fl 8-10 / 30 mm, & Complied as per Standard EN 62561-1., in IP67 180x180x100 Box.

Providing and laying of GI flat (32x6 mm) Strip. Having width- 32mm, Thickness- 6.0 mm, Material- Hot dipped Galvanized Iron, Cross Section- 192 mm2 Coating thickness- Avg. 70 microns. & Complied as per IEC 62561-2., with Clamp.

COOLING APPLIANCES:- Supply , install, commissioning and testing Dual water purifier system with RO + UV technology for normal, Hot & Cold outlet with inbuilt RO + UV protection, electric driven single phase, having appx storage capacity 80 Ltr normal cooling capacity 40 Ltr with automatic RO purification system at regular interval, built in stainless steel complete all specified. Make & Model: Best water Doctor, Model HIMA 7 NHC (ABS) or equivalent from Blue star / Voltas.

Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation between 170V to 250V with output voltage stabilized at 230V with accuracy of +/- 2.5% and of capacity 2 KVA complete all as specified Make: V-Guard (Model - VGSD100) or equivalent manufactures

Material and labour for Header made MS pipe of 250mm Dia heavy duty both end welded complete with suitable flenges for incomer & outgoing required at site

Material and labour for Header made MS pipe of 350mm Dia heavy duty both end welded complete with suitable flenges for incomer & outgoing required at site.

Supply & fixing MS work for pipe support anchoring, clamps, L angles, T angle etc required at site

Supply and fixing rigid non-metallic PVC conduit including junction boxes, tee, bend elbow, fixing accessories such as saddle, pipe hooks etc dia 25 mm complete

Supply and laying cable XLPE insulated, screened pvc bedded armoured electric power cable 1100 volt grade with stranded copper conductor of size 6.0 sq mm 3 core including cable gland and connection for pump sets.

Constructing masonry Chamber 600x600 x600 mm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design.

Supply, install, testing and commissioning open well submersible pump2.0HP total head 12 Mtr,(Dewatering pump) 230 volt electric driven single phase complete with pump control panel, submersible cable 7.0 RM (appx) and Liquid 4 point level indicator cum controller comprising with potential free contact relay, LED indicator, polypropylene float, PLC / control panel suitable for panel mounting including all fixing arrangement complete all as specified and directed

Supply and fixing Float Line anchors made in SS-316 fixed on concrete wall as per standard drawings and practice

Supply and fixing Float Line Flange anchoring socket made in SS-316 fixed on concrete wall as per standard drawings and practice

Supply and fixing Level anchor in SS-316 for false start indicator as per standard drawings and practice

Supply and fixing Level anchor in SS-316 for back stroke turn indicator as per standard drawings and practice

SEWAGE DISPOSAL : Supply and laying of DWC PE Pipe (SN8) 180 (OD)/163 (ID) mm dia laid and jointed including all fittings and fixtures complete all as specified

Supply and laying of DWC PE Pipe (SN8) 200 (OD)/183 (ID) mm dia laid and jointed including all fittings and fixtures complete all as specified

DECORATIVE TYPE CURTAIN RODS AND BRACKETS

Supply and fix 25mm dia polished stainless steel curtain rods confirming to SS-304 grade complete

Supply and fix decorative type stainless steel end caps, SS-304 grade suitable for 25mm dia stainless steel curtain rods complete

Supply and fix decorative type stainess steel, SS 304 grade curtain brackets fixed with stainless steel screws complete

MANNING AND OPERATION OF SWIMMING POOL AND DIVING POOL :- Out sourcing of maintenance and operation services to operate swimming pool and diving pool of E/M installation including the following in two shift per day from 1st shift 0600hrs to 1400 hrs and 2nd shift 1400hrs to 2200 hrs including sundays and holidays by deploying One FGM per shift. (For the First Year of 365 days during the defect liability period.)

(a) Machinery/equipment in main swimming pool. (i) Centrifugal mono block pump set 10 HP - 04 Nos (ii) Vertical type pressure filter capacity 125 CUM/hr- 03 Nos (iii) Wall mounting constant flow dosing pump set manual strok adjustment 10% to 100%- 3 Nos (iv) LT panel board -01 No

(b) Machinery/equipment in Diving pool. (i) Centrifugal mono block pump set 10 HP - 03 Nos (ii) Vertical type pressure filter capacity 125 CUM/hr- 02 Nos (iii) Wall mounting constant flow dosing pump set manual strok adjustment 10% to 100%- 2 Nos

(c) Details of routine works : (i) To operate pump sets installed at Filtration plant of swimming pool and diving pool and carry out checks of pipe line, pumps and panel boards for trouble free functioning. (ii) To operate suction and delivery valves of pump sets and inlets and out lets valves of balancing tanks. (iii) To operate inlet valves of swimming pool diving pool and changing room. (iv) To operate main valves of gravity main of swimming pool and diving pool feeding at S2 Tank. (v) To operate chlorination and filtration equipment and carry out routine check of chlorination plant and recording the results. (vi) To carry out periodical back wash of filtration unit and carry out minor repair in control panels dozing pumps and arresting leakage etc.

Carryout the suction sweeping of swimming pool and diving pool for removing the sediment slits/dirt and cleaning the walls, over flow channel, and channel grills etc all as directed.

Supply only bleaching powder commercial Grade 1 superior quality complete all as specified and directed.make as approved by the NMPT committee of E-in-C's Branch.

Supply only Poly aluminium Chloride Alum ( Inorganic soluble powder) complete all as specified and directed.make as approved by the NMPT committee of E-in-C's Branch.

Supply only calcium hydrochloride based Granular disinfectant for water treatment complete all as specified and directed. Make:- Purichlor or any other make approved by the NMPT committee of E-in-C's Branch.

Material and labour for Cleaning of Swimming pool and Diving pool of capacity 21.25 Lakh ltrs by acid solution complete all as specified and directed.

Out sourcing of maintenance and operation services to operate swimming pool and diving pool of E/M installation including the following in two shift per day from 1st shift 0600hrs to 1400 hrs and 2nd shift 1400hrs to 2200 hrs including sundays and holidays by deploying One FGM per shift. (For the Second Year of 365 days during the defect liability period.)

(a) Machinery/equipment in main swimming pool. (i) Centrifugal mono block pump set 10 HP - 04 Nos (ii) Vertical type pressure filter capacity 125 CUM/hr- 03 Nos (iii) Wall mounting constant flow dosing pump set manual strok adjustment 10% to 100%- 3 Nos (iv) LT panel board -01 No

(b) Machinery/equipment in Diving pool. (i) Centrifugal mono block pump set 10 HP - 03 Nos (ii) Vertical type pressure filter capacity 125 CUM/hr- 02 Nos (iii) Wall mounting constant flow dosing pump set manual strok adjustment 10% to 100%- 2 Nos

(c) Details of routine works : (i) To operate pump sets installed at Filtration plant of swimming pool and diving pool and carry out checks of pipe line, pumps and panel boards for trouble free functioning. (ii) To operate suction and delivery valves of pump sets and inlets and out lets valves of balancing tanks. (iii) To operate inlet valves of swimming pool diving pool and changing room. (iv) To operate main valves of gravity main of swimming pool and diving pool feeding at S2 Tank. (v) To operate chlorination and filtration equipment and carry out routine check of chlorination plant and recording the results. (vi) To carry out periodical back wash of filtration unit and carry out minor repair in control panels dozing pumps and arresting leakage etc.

Carryout the suction sweeping of swimming pool and diving pool for removing the sediment slits/dirt and cleaning the walls, over flow channel, and channel grills etc all as directed.

Supply only bleaching powder commercial Grade 1 superior quality complete all as specified and directed.make as approved by the NMPT committee of E-in-C's Branch.

Supply only Poly aluminium Chloride Alum ( Inorganic soluble powder) complete all as specified and directed.make as approved by the NMPT committee of E-in-C's Branch.

Supply only calcium hydrochloride based Granular disinfectant for water treatment complete all as specified and directed. Make:- Purichlor or any other make approved by the NMPT committee of E-in-C's Branch.

Material and labour for Cleaning of Swimming pool and Diving pool of capacity 21.25 Lakh ltrs by acid solution complete all as specified and directed.

Out sourcing of maintenance and operation services to operate swimming pool and diving pool of E/M installation including the following in two shift per day from 1st shift 0600hrs to 1400 hrs and 2nd shift 1400hrs to 2200 hrs including sundays and holidays by deploying One FGM per shift. (For the First year of 365 days after defect liability period of two years)

(a) Machinery/equipment in main swimming pool. (i) Centrifugal mono block pump set 10 HP - 04 Nos (ii) Vertical type pressure filter capacity 125 CUM/hr- 03 Nos (iii) Wall mounting constant flow dosing pump set manual strok adjustment 10% to 100%- 3 Nos (iv) LT panel board -01 No

(b) Machinery/equipment in Diving pool. (i) Centrifugal mono block pump set 10 HP - 03 Nos (ii) Vertical type pressure filter capacity 125 CUM/hr- 02 Nos. (iii) Wall mounting constant flow dosing pump set manual strok adjustment 10% to 100%- 2 Nos

(c) Details of routine works. (i) To operate pump sets installed at Filtration plant of swimming pool and diving pool and carry out checks of pipe line ,pumps and panel boards for trouble free functioning. (ii) To operate suction and delivery valves of pump sets and inlets and out lets valves of balancing tanks. (iii) To operate inlet valves of swimming pool diving pool and changing room. (iv) To operate main valves of gravity main of swimming pool and diving pool feeding at S2 Tank. (v) To operate chlorination and filtration equipment and carry out routine check of chlorination plant and recording the results. (vi) To carry out periodical back wash of filtration unit and carry out minor repair in control panels dozing pumps and arresting leakage etc.

Material and labour for Carryout the suction sweeping of swimming pool and diving pool for removing the sediment slits/dirt and cleaning the walls, over flow channel, and channel grills etc all as directed.

Supply only bleaching powder commercial Grade 1 superior quality complete all as specified and directed.make as approved by the NMPT committee of E-in-C's Branch.

Supply only Poly aluminium Chloride Alum ( Inorganic soluble powder) complete all as specified and directed.make as approved by the NMPT committee of E-in-C's Branch.

Supply only calcium hydrochloride based Granular disinfectant for water treatment complete all as specified and directed. Make:- Purichlor or any other make approved by the NMPT committee of E-in-C's Branch.

Material and labour for Cleaning of Swimming pool of capacity 21.25 Lakh ltrs by acid solution complete all as specified and directed.

Material and labour for Cleaning of Diving pool of capacity 15 Lakh ltrs by acid solution complete all as specified and directed.

Supply only deep leaf net with 5 Mtr Extension handle complete all as specified and directed.

Supply only Algae brush with 3 mtr handle complete all as specified and directed.

Material and labour for Dismantling the Electrical connection from motor and taking out the burnt 10 HP motor of flow rate . Flowrate : 125m3/h @ 12m.head. 10 HP Voltage 400V/ 3 ph. With Flange and adaptor 110mm dia from beds ,transporting to civil work shop , opening the motor and removing the burnt/old defective winding carefully cleaning the inner parts, rewinding the motor with same gauge supper enamelled copper wire of good insulation, varnishing, heating/drying and reassembling the motor and transporting to site , refixing on the existing beds ,connecting the electrical connection ,testing and commissioning all as directed.

Material and labour for Dismantling the Electrical connection from motor and taking out the burnt 3.0 HP motor from beds ,transporting to civil work shop , opening the motor and removing the burnt/old defective winding carefully cleaning the inner parts, rewinding the motor with same gauge supper enamelled copper wire of good insulation, varnishing, heating/drying and reassembling the motor and transporting to site , refixing on the existing beds ,connecting the electrical connection ,testing and commissioning all as directed.

Material and labour for Opening and servicing/overhauling the monoblock pump and motor 10 HP and replacing the defective bearing greasing replacing the burnout gland rope, studs, nuts, bolts, washers ,air releasing valve ,rubber gasket ,metal filling, turing/ grinding and balancing the shaft etc. varnishing the winding, drying and refixing the same all as directed at site.

Material and labour for Opening and servicing/overhauling the monoblock pump and motor 3.0 HP and replacing the defective bearing, greasing replacing the burnout gland rope, studs, nuts, bolts, washers ,air releasing valve ,rubber gasket ,metal filling, turing/ grinding and balancing the shaft etc. varnishing the winding, drying and refixing the same all as directed at site.

M&L for Dismantling the wall mounting constant flow dosing pump from Power connections : 220/240V, 50/60 Hz. and repairing the flow adjustment to Flow 20 l/hr @ 5 bar of pump head ,gear motors, rotor assembly with bearing brackets ,motor coil 250V 50 Hz etc and reassembling and testing all as directed.

Supply and fix PVC Flexible Vacuum hose pipe of size 40mm dia complete all as specified and directed.

Material and labour for preparing the surface by scrapping with wire brush and emery paper and painting with one coat of red oxide zinc chromate primer and two coast of synthetic enamel paint of existing shade including writing MES NO,out going and incoming electric supply, marking the water flow direction for the following equipments installed at Diving pool all as directed at site and as specified. (a) Monoblock pump set 10 HP -3 Nos (b) Vertical pressure filter of size 2000mm dia x 2040mm height - 2 Nos with butterfly valves (c)Water pipe lines and connected valves (d) LT Panel boards - 1 No (e)Sluice valve chamber & cover

Material and labour for preparing the surface by scrapping with wire brush and emery paper and painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of existing shade including writing MES NO,out going and incoming electric supply, marking the water flow direction for the following equipments installed at swimming pool all as directed at site and as specified. (a) Monoblock pump set 10 HP -4 Nos (b) Vertical pressure filter of size 2000mm dia x 2040mm height - 3 Nos with butterfly valves (c)Water pipe lines and connected valves (d)Sluice valve chamber & cover

Taking down unserviceable MCB, Supply and fixing 415V, 10KA 'C' curve miniature circuit breaker (MCB) of 4 poles TPN and current carrying capacity of 63Amps with connection testing and commissioning.complete all as specified and directed. Make:Havells/Legrand/L&T

Taking down unserviceable MCCB, supply and fix MCCB,415V,160Amps, 4 pole,36 KA complete all as specified and directed. Make:Havells/Legrand/L&T.

Taking down unserviceable MCCB,supply and fix MCCB,415V,125Amps, 4 pole,16 KA complete all as specified and directed. Make:Havells/Legrand/L&T.

Taking down unserviceable MCB,Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of TPN 32A current carrying capacity with connection testing and commissioning complete all as specified and directed. Make:Havells/Legrand/L&T

Supply and Laying flat submersible 1100 Volts grade, 3 core copper conductor PVC insulated and PVC sheathed cable of 6 Sq mm including taking down old material. Make:-Finolex/Havells/Polycab.

Supply and fixing single phase preventor 415Volts 50Hz including taking down of old material. (Make: -L&T/C&S/Schncider )

Supply and fix in replacement LED indication lamp of panel mounting type including taking down old material complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement of Digital Ammeter -0-100 Amps Accuracy class 1.1 ,0.5, flush mounting 96x96 mm complete all as specified and directed by Engineer-in-Charge.Make : AE/L&T/Havell

Supply and fix in replacement of Digital Voltmeter -0-500 Volts Input voltage 50-550 VAC ,Flush mounting 96x96 mm complete all as specified and directed by Engineer-in-Charge.Make : AE/L&T/Havell

Supply and fix in replacement ON/OFF push button for pump starter any make/type including taking down old material complete all as specified and directed by Engineer-in-Charge.Make : AE/L&T/Havell

M & L for Cleaning of internal walls of fibre glass and polyester resin pressure filters of size 2 mtr dia and 2.04 mtr height after removing the filter media by brushing with nylon brush and using bleaching powder and cleaning of existing pipe holes complete all as directed by Engineer in -charge

M & L for Taking out defective sand, Supply and Laying filter media (sand) of size 0.6 mm to 1.25mm in filter beds.

M & L for Taking out defective coarse gravel, supply and laying filter media (coarse gravel/fine gravel) of size 2.5mm in filter bed complete all as directed

M & L for Taking out defective pebbles, Supply and Laying filter media ( pebbles) of size 09-18mm in filter beds complete all as directed

M & L for Taking out defective agregate, Supply and Laying filter media ( agregate) of size 20-40mm in filter beds complete all as directed

M & L for Supply and fix Direct on line starter, 415 Volts 50Hz 3phase supply relay range for 3 HP motor.complete all as specified and directed. Make L&T/Havells/C&G.

M & L for Supply and fix SASD (Semi automatic star delta starter), for 10HP motor 415 Volts 50Hz 3phase supply relay range 13 - 21 Amps. Make L&T/Havells/C&G.

Supply only Digital portable type PH meter range 0-14 PH complete all as specified and directed.

Supply only Chlorine test kit with coloured ample complete with all testing fitment and 100 ML othodine solution in rexine finish wooden box/rexin box confirming to IS specification complete all as specified and directed.

M & L for Supply and fix Pump caddy for stand-alone pool cleaners. Made of anodized aluminium tube and a 460 mm x 370 mm plastic platform. Face plate in AISI-304 stainless steel.

Out sourcing of maintenance and operation services to operate swimming pool and diving pool of E/M installation including the following in two shift per day from 1st shift 0600hrs to 1400 hrs and 2nd shift 1400hrs to 2200 hrs including sundays and holidays by deploying One FGM per shift.(For the Second year of 365 days after defect liability period of two years)

(a) Machinery/equipment in main swimming pool. (i) Centrifugal mono block pump set 10 HP - 04 Nos (ii) Vertical type pressure filter capacity 125 CUM/hr- 03 Nos (iii) Wall mounting constant flow dosing pump set manual strok adjustment 10% to 100%- 3 Nos (iv) LT panel board -01 No

(b) Machinery/equipment in Diving pool. (i) Centrifugal mono block pump set 10 HP - 03 Nos (ii) Vertical type pressure filter capacity 125 CUM/hr- 02 Nos. (iii) Wall mounting constant flow dosing pump set manual strok adjustment 10% to 100%- 2 Nos

(c) Details of routine works. (i) To operate pump sets installed at Filtration plant of swimming pool and diving pool and carry out checks of pipe line ,pumps and panel boards for trouble free functioning. (ii) To operate suction and delivery valves of pump sets and inlets and out lets valves of balancing tanks. (iii) To operate inlet valves of swimming pool diving pool and changing room. (iv) To operate main valves of gravity main of swimming pool and diving pool feeding at S2 Tank. (v) To operate chlorination and filtration equipment and carry out routine check of chlorination plant and recording the results. (vi) To carry out periodical back wash of filtration unit and carry out minor repair in control panels dozing pumps and arresting leakage etc.

Material and labour for Carryout the suction sweeping of swimming pool and diving pool for removing the sediment slits/dirt and cleaning the walls, over flow channel, and channel grills etc all as directed.

Supply only bleaching powder commercial Grade 1 superior quality complete all as specified and directed.make as approved by the NMPT committee of E-in-C's Branch.

Supply only Poly aluminium Chloride Alum ( Inorganic soluble powder) complete all as specified and directed.make as approved by the NMPT committee of E-in-C's Branch.

Supply only calcium hydrochloride based Granular disinfectant for water treatment complete all as specified and directed. Make:- Purichlor or any other make approved by the NMPT committee of E-in-C's Branch.

Material and labour for Cleaning of Swimming pool of capacity 21.25 Lakh ltrs by acid solution complete all as specified and directed.

Material and labour for Cleaning of Diving pool of capacity 15 Lakh ltrs by acid solution complete all as specified and directed.

Supply only deep leaf net with 5 Mtr Extension handle complete all as specified and directed.

Supply only Algae brush with 3 mtr handle complete all as specified and directed.

Material and labour for Dismantling the Electrical connection from motor and taking out the burnt 10 HP motor of flow rate . Flowrate : 125m3/h @ 12m.head. 10 HP Voltage 400V/ 3 ph. With Flange and adaptor 110mm dia from beds ,transporting to civil work shop , opening the motor and removing the burnt/old defective winding carefully cleaning the inner parts, rewinding the motor with same gauge supper enamelled copper wire of good insulation, varnishing, heating/drying and reassembling the motor and transporting to site , refixing on the existing beds ,connecting the electrical connection ,testing and commissioning all as directed.

Material and labour for Dismantling the Electrical connection from motor and taking out the burnt 3.0 HP motor from beds ,transporting to civil work shop , opening the motor and removing the burnt/old defective winding carefully cleaning the inner parts, rewinding the motor with same gauge supper enamelled copper wire of good insulation, varnishing, heating/drying and reassembling the motor and transporting to site , refixing on the existing beds ,connecting the electrical connection ,testing and commissioning all as directed.

Material and labour for Opening and servicing/overhauling the monoblock pump and motor 10 HP and replacing the defective bearing greasing replacing the burnout gland rope, studs, nuts, bolts, washers ,air releasing valve ,rubber gasket ,metal filling, turing/ grinding and balancing the shaft etc. varnishing the winding, drying and refixing the same all as directed at site.

Material and labour for Opening and servicing/overhauling the monoblock pump and motor 3.0 HP and replacing the defective bearing, greasing replacing the burnout gland rope, studs, nuts, bolts, washers ,air releasing valve ,rubber gasket ,metal filling, turing/ grinding and balancing the shaft etc. varnishing the winding, drying and refixing the same all as directed at site.

M&L for Dismantling the wall mounting constant flow dosing pump from Power connections : 220/240V, 50/60 Hz. and repairing the flow adjustment to Flow 20 l/hr @ 5 bar of pump head ,gear motors, rotor assembly with bearing brackets ,motor coil 250V 50 Hz etc and reassembling and testing all as directed.

Supply and fix PVC Flexible Vacuum hose pipe of size 40mm dia complete all as specified and directed.

Material and labour for preparing the surface by scrapping with wire brush and emery paper and painting with one coat of red oxide zinc chromate primer and two coast of synthetic enamel paint of existing shade including writing MES NO,out going and incoming electric supply, marking the water flow direction for the following equipments installed at Diving pool all as directed at site and as specified. (a) Monoblock pump set 10 HP -3 Nos (b) Vertical pressure filter of size 2000mm dia x 2040mm height - 2 Nos with butterfly valves (c)Water pipe lines and connected valves (d) LT Panel boards - 1 No (e)Sluice valve chamber & cover

Material and labour for preparing the surface by scrapping with wire brush and emery paper and painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of existing shade including writing MES NO,out going and incoming electric supply, marking the water flow direction for the following equipments installed at swimming pool all as directed at site and as specified. (a) Monoblock pump set 10 HP -4 Nos (b) Vertical pressure filter of size 2000mm dia x 2040mm height - 3 Nos with butterfly valves (c)Water pipe lines and connected valves (d)Sluice valve chamber & cover

Taking down unserviceable MCB, Supply and fixing 415V, 10KA 'C' curve miniature circuit breaker (MCB) of 4 poles TPN and current carrying capacity of 63Amps with connection testing and commissioning.complete all as specified and directed. Make:Havells/Legrand/L&T

Taking down unserviceable MCCB, supply and fix MCCB,415V,160Amps, 4 pole,36 KA complete all as specified and directed. Make:Havells/Legrand/L&T.

Taking down unserviceable MCCB,supply and fix MCCB,415V,125Amps, 4 pole,16 KA complete all as specified and directed. Make:Havells/Legrand/L&T.

Taking down unserviceable MCB,Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of TPN 32A current carrying capacity with connection testing and commissioning complete all as specified and directed. Make:Havells/Legrand/L&T

Supply and Laying flat submersible 1100 Volts grade, 3 core copper conductor PVC insulated and PVC sheathed cable of 6 Sq mm including taking down old material. Make:-Finolex/Havells/Polycab.

Supply and fixing single phase preventor 415Volts 50Hz including taking down of old material. (Make: -L&T/C&S/Schncider )

Supply and fix in replacement LED indication lamp of panel mounting type including taking down old material complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement of Digital Ammeter -0-100 Amps Accuracy class 1.1 ,0.5, flush mounting 96x96 mm complete all as specified and directed by Engineer-in-Charge.Make : AE/L&T/Havell

Supply and fix in replacement of Digital Voltmeter -0-500 Volts Input voltage 50-550 VAC ,Flush mounting 96x96 mm complete all as specified and directed by Engineer-in-Charge.Make : AE/L&T/Havell

Supply and fix in replacement ON/OFF push button for pump starter any make/type including taking down old material complete all as specified and directed by Engineer-in-Charge.Make : AE/L&T/Havell

M & L for Cleaning of internal walls of fibre glass and polyester resin pressure filters of size 2 mtr dia and 2.04 mtr height after removing the filter media by brushing with nylon brush and using bleaching powder and cleaning of existing pipe holes complete all as directed by Engineer in -charge

M & L for Taking out defective sand, Supply and Laying filter media (sand) of size 0.6 mm to 1.25mm in filter beds.

M & L for Taking out defective coarse gravel, supply and laying filter media (coarse gravel/fine gravel) of size 2.5mm in filter bed complete all as directed

M & L for Taking out defective pebbles, Supply and Laying filter media ( pebbles) of size 09-18mm in filter beds complete all as directed

M & L for Taking out defective agregate, Supply and Laying filter media ( agregate) of size 20-40mm in filter beds complete all as directed

M & L for Supply and fix Direct on line starter, 415 Volts 50Hz 3phase supply relay range for 3 HP motor.complete all as specified and directed. Make L&T/Havells/C&G.

M & L for Supply and fix SASD (Semi automatic star delta starter), for 10HP motor 415 Volts 50Hz 3phase supply relay range 13 - 21 Amps. Make L&T/Havells/C&G.

Supply only Digital portable type PH meter range 0-14 PH complete all as specified and directed.

Supply only Chlorine test kit with coloured ample complete with all testing fitment and 100 ML othodine solution in rexine finish wooden box/rexin box confirming to IS specification complete all as specified and directed.

M & L for Supply and fix Pump caddy for stand-alone pool cleaners. Made of anodized aluminium tube and a 460 mm x 370 mm plastic platform. Face plate in AISI-304 stainless steel.

Out sourcing of maintenance and operation services to operate swimming pool and diving pool of E/M installation including the following in two shift per day from 1st shift 0600hrs to 1400 hrs and 2nd shift 1400hrs to 2200 hrs including sundays and holidays by deploying One FGM per shift.(For the Third year of 365 days after defect liability period of two years)

(a) Machinery/equipment in main swimming pool. (i) Centrifugal mono block pump set 10 HP - 04 Nos (ii) Vertical type pressure filter capacity 125 CUM/hr- 03 Nos (iii) Wall mounting constant flow dosing pump set manual strok adjustment 10% to 100%- 3 Nos (iv) LT panel board -01 No

(b) Machinery/equipment in Diving pool. (i) Centrifugal mono block pump set 10 HP - 03 Nos (ii) Vertical type pressure filter capacity 125 CUM/hr- 02 Nos. (iii) Wall mounting constant flow dosing pump set manual strok adjustment 10% to 100%- 2 Nos

(c) Details of routine works. (i) To operate pump sets installed at Filtration plant of swimming pool and diving pool and carry out checks of pipe line ,pumps and panel boards for trouble free functioning. (ii) To operate suction and delivery valves of pump sets and inlets and out lets valves of balancing tanks. (iii) To operate inlet valves of swimming pool diving pool and changing room. (iv) To operate main valves of gravity main of swimming pool and diving pool feeding at S2 Tank. (v) To operate chlorination and filtration equipment and carry out routine check of chlorination plant and recording the results. (vi) To carry out periodical back wash of filtration unit and carry out minor repair in control panels dozing pumps and arresting leakage etc.

Material and labour for Carryout the suction sweeping of swimming pool and diving pool for removing the sediment slits/dirt and cleaning the walls, over flow channel, and channel grills etc all as directed.

Supply only bleaching powder commercial Grade 1 superior quality complete all as specified and directed.make as approved by the NMPT committee of E-in-C's Branch.

Supply only Poly aluminium Chloride Alum ( Inorganic soluble powder) complete all as specified and directed.make as approved by the NMPT committee of E-in-C's Branch.

Supply only calcium hydrochloride based Granular disinfectant for water treatment complete all as specified and directed. Make:- Purichlor or any other make approved by the NMPT committee of E-in-C's Branch.

Material and labour for Cleaning of Swimming pool of capacity 21.25 Lakh ltrs by acid solution complete all as specified and directed.

Material and labour for Cleaning of Diving pool of capacity 15 Lakh ltrs by acid solution complete all as specified and directed.

Supply only deep leaf net with 5 Mtr Extension handle complete all as specified and directed.

Supply only Algae brush with 3 mtr handle complete all as specified and directed.

Material and labour for Dismantling the Electrical connection from motor and taking out the burnt 10 HP motor of flow rate . Flowrate : 125m3/h @ 12m.head. 10 HP Voltage 400V/ 3 ph. With Flange and adaptor 110mm dia from beds ,transporting to civil work shop , opening the motor and removing the burnt/old defective winding carefully cleaning the inner parts, rewinding the motor with same gauge supper enamelled copper wire of good insulation, varnishing, heating/drying and reassembling the motor and transporting to site , refixing on the existing beds ,connecting the electrical connection ,testing and commissioning all as directed.

Material and labour for Dismantling the Electrical connection from motor and taking out the burnt 3.0 HP motor from beds ,transporting to civil work shop , opening the motor and removing the burnt/old defective winding carefully cleaning the inner parts, rewinding the motor with same gauge supper enamelled copper wire of good insulation, varnishing, heating/drying and reassembling the motor and transporting to site , refixing on the existing beds ,connecting the electrical connection ,testing and commissioning all as directed.

Material and labour for Opening and servicing/overhauling the monoblock pump and motor 10 HP and replacing the defective bearing greasing replacing the burnout gland rope, studs, nuts, bolts, washers ,air releasing valve ,rubber gasket ,metal filling, turing/ grinding and balancing the shaft etc. varnishing the winding, drying and refixing the same all as directed at site.

Material and labour for Opening and servicing/overhauling the monoblock pump and motor 3.0 HP and replacing the defective bearing, greasing replacing the burnout gland rope, studs, nuts, bolts, washers ,air releasing valve ,rubber gasket ,metal filling, turing/ grinding and balancing the shaft etc. varnishing the winding, drying and refixing the same all as directed at site.

M&L for Dismantling the wall mounting constant flow dosing pump from Power connections : 220/240V, 50/60 Hz. and repairing the flow adjustment to Flow 20 l/hr @ 5 bar of pump head ,gear motors, rotor assembly with bearing brackets ,motor coil 250V 50 Hz etc and reassembling and testing all as directed.

Supply and fix PVC Flexible Vacuum hose pipe of size 40mm dia complete all as specified and directed.

Material and labour for preparing the surface by scrapping with wire brush and emery paper and painting with one coat of red oxide zinc chromate primer and two coast of synthetic enamel paint of existing shade including writing MES NO,out going and incoming electric supply, marking the water flow direction for the following equipments installed at Diving pool all as directed at site and as specified. (a) Monoblock pump set 10 HP -3 Nos (b) Vertical pressure filter of size 2000mm dia x 2040mm height - 2 Nos with butterfly valves (c)Water pipe lines and connected valves (d) LT Panel boards - 1 No (e)Sluice valve chamber & cover

Material and labour for preparing the surface by scrapping with wire brush and emery paper and painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of existing shade including writing MES NO,out going and incoming electric supply, marking the water flow direction for the following equipments installed at swimming pool all as directed at site and as specified. (a) Monoblock pump set 10 HP -4 Nos (b) Vertical pressure filter of size 2000mm dia x 2040mm height - 3 Nos with butterfly valves (c)Water pipe lines and connected valves (d)Sluice valve chamber & cover

Taking down unserviceable MCB, Supply and fixing 415V, 10KA 'C' curve miniature circuit breaker (MCB) of 4 poles TPN and current carrying capacity of 63Amps with connection testing and commissioning.complete all as specified and directed. Make:Havells/Legrand/L&T

Taking down unserviceable MCCB, supply and fix MCCB,415V,160Amps, 4 pole,36 KA complete all as specified and directed. Make:Havells/Legrand/L&T.

Taking down unserviceable MCCB,supply and fix MCCB,415V,125Amps, 4 pole,16 KA complete all as specified and directed. Make:Havells/Legrand/L&T.

Taking down unserviceable MCB,Supply and fixing 415V 10KA 'C' curve miniature circuit breaker (MCB) of TPN 32A current carrying capacity with connection testing and commissioning complete all as specified and directed. Make:Havells/Legrand/L&T

Supply and Laying flat submersible 1100 Volts grade, 3 core copper conductor PVC insulated and PVC sheathed cable of 6 Sq mm including taking down old material. Make:-Finolex/Havells/Polycab.

Supply and fixing single phase preventor 415Volts 50Hz including taking down of old material. (Make: -L&T/C&S/Schncider )

Supply and fix in replacement LED indication lamp of panel mounting type including taking down old material complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement of Digital Ammeter -0-100 Amps Accuracy class 1.1 ,0.5, flush mounting 96x96 mm complete all as specified and directed by Engineer-in-Charge.Make : AE/L&T/Havell

Supply and fix in replacement of Digital Voltmeter -0-500 Volts Input voltage 50-550 VAC ,Flush mounting 96x96 mm complete all as specified and directed by Engineer-in-Charge.Make : AE/L&T/Havell

Supply and fix in replacement ON/OFF push button for pump starter any make/type including taking down old material complete all as specified and directed by Engineer-in-Charge.Make : AE/L&T/Havell

M & L for Cleaning of internal walls of fibre glass and polyester resin pressure filters of size 2 mtr dia and 2.04 mtr height after removing the filter media by brushing with nylon brush and using bleaching powder and cleaning of existing pipe holes complete all as directed by Engineer in -charge

M & L for Taking out defective sand, Supply and Laying filter media (sand) of size 0.6 mm to 1.25mm in filter beds.

M & L for Taking out defective coarse gravel, supply and laying filter media (coarse gravel/fine gravel) of size 2.5mm in filter bed complete all as directed

M & L for Taking out defective pebbles, Supply and Laying filter media ( pebbles) of size 09-18mm in filter beds complete all as directed

M & L for Taking out defective agregate, Supply and Laying filter media ( agregate) of size 20-40mm in filter beds complete all as directed

M & L for Supply and fix Direct on line starter, 415 Volts 50Hz 3phase supply relay range for 3 HP motor.complete all as specified and directed. Make L&T/Havells/C&G.

M & L for Supply and fix SASD (Semi automatic star delta starter), for 10HP motor 415 Volts 50Hz 3phase supply relay range 13 - 21 Amps. Make L&T/Havells/C&G.

Supply only Digital portable type PH meter range 0-14 PH complete all as specified and directed.

Supply only Chlorine test kit with coloured ample complete with all testing fitment and 100 ML othodine solution in rexine finish wooden box/rexin box confirming to IS specification complete all as specified and directed.

M & L for Supply and fix Pump caddy for stand-alone pool cleaners. Made of anodized aluminium tube and a 460 mm x 370 mm plastic platform. Face plate in AISI-304 stainless steel.

JAIN BUILDER

KEC International Ltd

SCC Infrastructure Pvt. Ltd