PROVISION OF GUARD REST ROOM, LMG WITH TOILET AT 04 ACRES CG LAND, VOLLEY BALL COURT FOR TROOPS , AUTOMATIC POOL COVER FOR SWIMMING POOL AT CGDHQ-1, PORBANDAR AND PROVN OF CUTTING AND FILLING AND RETAINING WALL BEHIND MI ROOM AT ICGS VADINAR UNDER

Amount

SCHEDULE 'A'

Surface excavation n.exc 30 cm deep averaging 15 cm deep and getting out in soft/disintegrated rocks including Clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots, and trees not exceeding 30 cm girth (measured one metre above ground level) and removing rubbish upto a distance of 50 metres complete all as specified and as directed..

Excavation over areas n.exc 1.5 M deep and getting out in soft/disintegrated rocks.

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cessipts, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil

Excavation in trenches n.exc 1.5m wide and n. exc. 1.5m deep and getting out in soft/disintegrated rocks

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick using excavated material all as specified.

Returning filling of retaining walls using approved earth obtained from excavation incl spreading, levelling in layers, watering, well ramming, etc,.

Removing excavated material to a distance n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed by engineer-in-charge.

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5m high from base

Excavation in post holes (or similar holes) each n exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n exc 25cm, watering and removing surplus soil to a distance n exc 25m and making good surface hard/dense soil.

Supply only Moorum/red bajri

M&Lsand filling in floor.or in foundation etc, including watering and consolidation etc complete all as specified and as directed.

M&L Hardcore of guage n.exc. 63mm, deposited spread & levelled in layers n.exc.15CM thick, watered & rolled/ rammed to a true surface using broken stone or boulders all as specified and as directed by engineer-in-charge.

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured)

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

M&L Plain cement concrete, type D2, (1:4:8, using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc all as specified and as as directed by engineer-in-charge. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L Plain cement concrete, type B0, (1:2:4, using 12.5mm graded stone aggregates) as in coping/benching incl necessary form work.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in foundation including raft footing foundation beam plinth beam bases for columns etc basement slab under reamed piles and mass concrete Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in Columns,pillars,piers, posts and struts Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in chajjas, floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in beams,cantilevers, bressumers and lintels over 1.5 mtr span complete all as specified and directed by Engr-in-charge. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in slabs supported onwalls, beams and colums in floors, roofs, landings, balconies, canopies ,deck slabs and in shelves and the like complete all as specified and directed by Engr-in-charge Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

Supply only integral water proofing compond

M&L Boulder pitching, laid dry, hand packed tightly, grouted with cement and sand mortar 1:6 ,complete as in backside of retaining wall all as specified and as directed.

M& L Marble 18 to 20 mm thick (table rubbed and polishing) as in Steps, jambs, pillars, window cills, cooking platforms and the like in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrana as directed by Engr-in-charge complete.

Formwork to sides of concrete foundations, footings,bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter,for rough finished surfaces of flat concrete..

Form Work to sides of pillars colums square or rectangular ,for rough finished surfaces of flat concrete.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc for rough finished surfaces of flat concrete.

Form work to soffits of suspended slab such as roof slab floor slab landing and similer work not exceeding 200mm thick (horizontal or sloping) ,for rough finished surfaces of flat concrete.

Formwork to chajjas including edges ,for rough finished surfaces of flat concrete.

M&L 2nd class hard wood plain,solid,straight chowkats and frames,wrought,framed rebated on the solid,rounded or chamfered,put together with glue pinned at joints

S & F 35mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads etc complete all as specified and directed by Engr-in-Charge.

S & F 35mm thick 2nd class hard wood plain framed panelled shutter (any number of panels) with panels of timber flat on both sides, feather edged or of veneered particle board medium density, wood particle board with commercial face veneer etc complete all as specified and directed by Engr-in-Charge.

S & F Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with 19x 19mm MS square tubes, provided with EPDM rubber gasket throughout the frame fixed in opening complete as per manufacturer's specifications and as directed by Engineer-in-Charge

S & F 30 mm thick factory made solid panel PVC door shutter conferming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming stiles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-inCharge

S&F Butt hinges, 100 mm medium weight, cold rolled mild steel complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium, anodised, barrel tower bolts 200 mm long of extruded section and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 125 mm long Extruded aluminium alloy handles, fabricated type,anodised (ISI Marked) complete all as specified and directed.

S&F 140mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F Brass chromium plated finials for 25mm dia curtain rod complete all as specified and as directed by engineer-in-charge.

S&F 25mm dia Powder coated aluminium decorative type curtain rod complete all as specified and as directed. Note: colour of curtain rod shall be approved by Engineer-in-Charge.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engr-in-Charge.

M&L Porbandar stone masonary, block in course, well bonded and bedded, built in CM 1:6 all as specified and as directed by engineer-in-charge.

S&F MS hold fast of flat iron 25 x 3 mm conforming to Fe 410-0 or Fe 310-0.

M&L Mild steel CRS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. etc complete all as specified and directed by Engr-in-charge.

M&L Mild steel CRS TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. etc complete all as specified and directed by Engr-in-charge.

All as per above item No.48.00 but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders etc complete all as specified and directed by Engr-in-charge.

S&F powder coated Anodised aluminium frame (minimum thickness of powder coating 50 micron) for doors, shutters, sliding windows and windows ventilators with or without rebates including joining cleats for fixing etc. complete all as specified and as directed by Engr-in-Charge.

S&F 5.5 mm thick Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5sq. m in each pane all as specified and as directed by engineer-in-charge.

S&F Aluminium grill with suitable aluminium anodised frame F/H section manufactured by M/s DECO GRILL as per design No DG-104, 100mm x 5.5mm to 6.5 mm thick with necessary channels and clips complete all as specified and as directed by Engr-in-Charge,

S&F Neoprene rubber beading of U or C section suitable for 5mm thick glass fixed along with edges of aluminium glass panes of joinery, all as directed by Engineer-in-charge.

S&F UPVC, double flat / groove type, roller for sliding windows all as directed by Engineer-in-charge. Note: Rollers shall conform to the samples kept with the Engineer-in-Charge.

S&F 100mm long powder coated Aluminium starlock for sliding window shutters conforming to the samples held in the office of Engineer-in-charge.

M&L 100mm thick, Plain Cement concrete, type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base of floors even and rough finished to receive topping layer complete all as specified and as directed by Engr-in-Charge.

M&L 25mm thick, Plain Cement concrete, type B-1, 1:2:4 (using 20mm graded stone aggregate) as in sub base of floors even and rough finished to receive topping layer complete all as specified and as directed by Engr-in-Charge.

M&L Joint free coloured ceramic tiles 8 to 9 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry over screed bed 15 mm thick 1:6 and pointed in white or coloured cement to match complete all as specified and as directed by Engr-in-Charge.

All as per item ser no 58.00 here-in-before but in skirting/dado or verticle surfaces with back coat bedding layer of 10 mm thick 1:4 and pointed in white or coloured cement to match complete all as specified and as directed by Engr-in-Charge.

M&L Glazed coloured ceramic tiles in verticle surfaces 300x 200x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match over backing bedding layer 10mm thick 1:4 and pointed in white or coloured cement to match etc complete all as specified and directed by Engr-in-charge.

M&L 50mm thick, Plain Cement concrete, type C-2, 1:3:6 (using 40mm graded stone aggregate) as in floor finish even and fair finished even and smooth without using extra cement. complete all as specified and as directed by Engr-in-Charge.

M&L 80 mm thick, M-40 grade, machine pressed precast concrete interlocking paver block of any shape and size with grey cement and pigment confirming to IS 15658-2006 complete all as specified

M&L Rendering 15 mm thick in cement mortar 1:6 on fair faces of pcc block masonry and finished even and smooth without using extra cement

M&L Rendering 15 mm thick in cement mortar 1:4 on fair faces of pcc block masonry and finished even and smooth without using extra cement

M&L Rendering 5mm thick in CM(1:3) on ceiling finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of newly plastered surfaces of wall and applying Two coats of OBD over a coat of chalk white primer complete all as specified and as directed by Engr-in-Charge.

M&L Two coats of OBD on new plastered surfaces of ceiling over a coat of chalk white primer including preparation of newly plastered surfaces complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete all as specified.

M & L Preparation of new wooden surfaces of any description, not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer of approved shade complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of zinc chrome primer, complete all as specified and as directed.

M&L 20mm thick cement plaster in cement mortar 1:4 mixed with water proofing compound as in roof treatment when conc is green complete all as specified and directed.

M&L APP based membrane course roof treatment in layers with following provisions:- (i) Applying one coat of bitumen's primer polymerized primer oil based coat, evenly @ 0.3 litre/Sqm as priming coat to the prepared surfaces, till the surfaces is properly impregnated and the solvent oil in the base primer shall be allowed to evaporated completely. (ii) Applying APP based pre-fabricated with non woven polyester reinforced membrane stabilized with fibre glass strands and top with grey mineral slates 3mm thick and weight not less than 3.50 Kg/Sqm by torch application method. (iii) Applying a coat of solar reflective bituminous aluminium paint @ 0.10Kg/Sqm over mineral surface.

Forming Contraction (Dummy) joints 50 mm deep x 10mm wide, filled with grade 'A" sealing compound

S&F 100mm dia GI tubing, medium grade, embeded in column etc complete all as specified and as directed.

S&F 80mm dia GI tubing medium grade galvanised,with all fitting complete all as specified and directed..

S&F 50mm dia low density polythene pipe (LDPE) of pressure rating 6 kg/sqcm as in weep holes.

S&L 25mm OD, CPVC pipes, of SDR -11 & plain CPVC SDR fittings for Hot/cold water for sizes mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all as per manufacturers recommendations and as specified.

S&L 20mm OD, CPVC pipes, of SDR -11 & plain CPVC SDR fittings for Hot/cold water for sizes mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all as per manufacturers recommendations and as specified.

S&F Vitreous China wash downwater closet pan (pedestal pattern), white (including fixing bolts & flush pipe, plastic water closet seat,black, closed pattern with bottom, and cover and mild steel chromium plated or aluminised hinging device etc.) complete all as specified and directed by Engineer-in-Charge

S & F Vitreous china wash hand basin, white, flat back, of size 550 x 400 mm including waste chain and plug or porcelain stopper but including cutting for and pinning in ends of brackets all as specified and directed. Make: CERA Cat Pat No-S2030121W or Equivalent

S&F 20mm dia Fancy type, Tubular towel rail, , brass CP, 60cm long between flanges complete all as specified and directed by Engr-in-Charge. Make:- CERA Cat Pat No-F5003102 or Equivalent

S&F PVC connections 15mm size with PTMT nuts of length 450mm Make : Prayag and equivalent as approved by Engr-in-Charge

M&L 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F 50mm bore High density polyethylene (HDPE) pipes of pressure rating 6kgf/sq.cm laid in trenches or in any position complete all as specified

S&F 1000 Litre three layered capacity rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed in position all as specified and directed including provision of 200mm long 50mm bore GI nipples for inlet, outlet, overflow, drain out pipe including provision of check nuts.

S&F Gun-metal, globe or gate valves 25 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge

S&F 20mm dia ball valves high pressure of PTMT epoxy coated aluminium rod & high density plastic ball screwed for iron pipes and fixed.(Minimum weight 20mm-210gms) complete all as specified and as directed by Engr-in-Charge

S&F 15 mm dia Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and directed by Engineer in Charge. Make: CERA Cat Pat No-F1005101 or Equivalent

S&F 110 mm dia PVC (SWR) pipe grade ‘A’ single socketed in any length perforated PVC drain pipe for drainage purpose, with rubber ring joints jointing with cement solvent solution, laid in trenches or in floors complete all as specified

S&F 110 mm dia PVC (SWR) pipe grade ‘A’ single socketed in any length, jointing with cement solvent solution, fixed to walls complete all as specified

S&F 75 mm dia PVC (SWR) pipe grade ‘A’ single socketed in any length, jointing with cement solvent solution, fixed to walls complete all as specified

S&F PVC(SWR) bend with acess door of any dia provided with access door for 75 mm dia pipe complete all as specified

S&F PVC(SWR) bend with acess door of any dia provided with access door for 110 mm dia pipe complete all as specified

S&F PVC (SWR) branch piece,single (Single Y) equal or unequal 110 mm dia complete all as specified & directed.

S&F PVC (SWR) branch piece,double (double Y) equal or unequal 110 mm dia complete all as specified & directed.

S&F PVC (SWR) branch piece, single(Y) equal or unequal of 75mm bore.complete all as specified and as directed by Engr-in-Charge.

S&F PVC (SWR) junction single (single T) equal or unequal of 75mm bore complete all as specified and as directed by Engr-in-Charge.

S&F PVC(SWR) vent cowl as specified of dia 75mm bore complete all as specified and as directed by Engr-in-Charge.

S&F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

S&F vitreous China Urinal, Half stall type, white (excluding flushing cistern and flush pipe and waste pipe) complete all as specified and as directed.

S & F 15 mm bore Stop Valve (Concealed Type) Cast Copper Alloy fancy type, Chromium plated with long shank and cup, high pressure, with crutch, screwed both ends for iron pipe or for unions and fixed. Make : Prayag (Cat Pat No-8518) or equivalent as approved by Engr-in-Charge

S&F 15mm dia Bib taps, with flange chromium plated cast copper alloy with crutch or butterfly handle complete all as specified and directed. Make : Prayag (Cat Pat No-8306) or equivalent as approved by Engr-in-Charge

S&F 10 lit.capacity PVC valveless, syphonic action type, flushing cistern,low level, white, with inlet,ball valve, float and handle including brackets complete all as specified. Make : Prayag (Cat Pat No-501) or equivalent as approved by Engr-in-Charge

S&F 15mm Angle Cock, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Make : Prayag (Cat Pat No-8510) or equivalent as approved by Engr-in-Charge

S&F Glass Shelf 500 x 60mm (with ABS Brackets) 450 x 125 x 6mm complete all as specified & directed. Make : Prayag (Cat Pat No- BEA-47) and equivalent as approved by Engr-in-Charge

S&F Corner Glass Shelf 300mm (with ABS Brackets) 300 x 600mm complete all as specified & directed. Make : Prayag (Cat Pat No- BEA-46) and equivalent as approved by Engr-in-Charge

S&F Soap Dish CP Brass complete all as specified & directed. Make : Prayag (Cat Pat No-BA-45) or equivalent as approved by Engr-in-Charge

S&F 7" over head shower with 225mm with flange complete all as Specified. Make : Prayag (Cat Pat No BS-78) or equivalent model as approved by Engr-in-Charge

S&F Health Faucet square with 1 mtr tube and hook complete all as specified and as directed by Engr-in-Charge, fixed . Make : Prayag (Cat Pat No-BEA-85) as approved by Engr-in-Charge

S&F Toilet Paper Holder, complete all as specified and as directed by Engr-in-Charge, fixed . Make : Prayag (Cat Pat No BA-18) or equivalent from makes given in list of makes.

S&F grating doom 100mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed..

S&F 32mm dia PVC (flexible) waste pipe, 800mm long for WHB/Kitchen sink/Urninal complete.

S&F 40mm dia PVC (flexible) waste pipe, 800mm long for WHB/Kitchen sink/Urninal complete.

S&F 32mm dia CP waste fittings, brass chromium plated for glazed ware sinks, basins, etc, with long screwed shanks & fly nuts, flange end based in red lead cement complete all as specified & directed.

S&F 40mm dia CP waste fittings, brass chromium plated for glazed ware sinks, basins, etc, with long screwed shanks and fly nuts, flange end based in red lead cement complete all as specified & directed.

S&F Cabinet Mirror 400 x 500 mm, Make : Prayag (Cat Pat No 554) or equivalent as approved by GE. complete all as specified and as directed by Engr-in-Charge

S & F Swimming Pool cover with manual Roller. Size of pool cover - 27 MT X 14.5 MT With Eyelets & Aluminium Foil Coating with PE bubble. Swimming Pool Cover Thickness: 600µm pool cover and Including Aluminium Roller adjustable type - 4nos Make of Pool Cover: Ion Exchange/Astral Pool/Pentair

Dismantling of SS Pipe as in swimming pool ladder and making good the disturbed surfaces complete all as specified and directed.

M&L Point wiring complete with 1.5 Sqmm single core PVC Insulated but unsheathed multistranded copper conductor FRLS cable 650/1100 Volt grade down through and including non metallic rigid PVC heavy duty concealed conduit, min 20mm external dia,heavy duty, but shall be increased to suitable size, as per requirement in accordance with clause 19.125 of SSR Part I, ISI marked, including conduit accessories like bends,tees,junction box etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sqmm earth wire, single core PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including sunken type pressed steel terminal boxes of suitable size with 2.8mm thick bakelite sheet white/coloured top cover Make Finolex/Havells/ NICCO/Anchor (a) One light /Fan point controlled by one,one way 5 Amps SP switch Note: The cost of cutting/chasing in walls/floors/ceilings wherever required shall be deemed to be included in the quoted rate.

All as per item no 119 but (b) one fan/Exhaust fan point controlled by 1 one way switch

All as per item no 119 but (b) one 3 pin 6A socket outlet on independent board

All as per item no 119 but (b) one 3 pin 6A socket outlet on same board

M&L Point wiring complete with 2.5 Sqmm single core PVC Insulated but unsheathed multistranded copper conductor FRLS cable 650/1100 Volt grade down through and including non metallic rigid PVC heavy duty concealed conduit, min 20mm external dia,heavy duty, but shall be increased to suitable size, as per requirement in accordance with clause 19.125 of SSR Part I, ISI marked, including conduit accessories like bends,tees,junction box etc fixed concealed/recessed in wall or ceiling etc including 2.5 Sqmm earth wire, single core PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including sunken type pressed steel terminal boxes of suitable size with 2.8mm thick bakelite sheet white/coloured top cover Make Finolex/Havells/ NICCO/Anchor (a) One 3 pin 15A socket outlet Note: The cost of cutting/chasing in walls/floors/ceilings wherever required shall be deemed to be included in the quoted rate.

S&F Switch piano flush button, 1 way, 6 Amps,240V (ISI marked).complete all as specified and as directed.

S&F Switch socket outlet, Multipurpose, 6 pin 16A, Flush type, controlled by one piano switch, 240V (ISI Marked) complete all as specified and as directed.

S&F Switch socket outlet, Multipurpose, 2 in 1, 5 pin 6A, Flush type, controlled by one piano switch, 240V (ISI Marked) complete all as specified and as directed.

S&F Ceiling rose, surface bakelite, 65x17mm, three terminals (ISI Marked) complete all as specified and as directed.

S&F Stepped type electronic fan regulator, flush type complete all as specified and directed.

S&F 25W LED Street lights, lumen output not less than 2500l, high pressure die cast aluminium housing, 140-270V, 50Hz, PF>0.9, including 12mm long 40/50mm bore, light grade,GI pipe mounting bracket made to shape with and including MS Clamps of FI 40mmX6mm with buts, bolts, washers,and including electric connection using 3Core 1Sqmm PVC Insulated Copper Cable from control box to fitting complete all as specified and directed. Make: Wipro (Skyline LED)/ Halonix (LUMOX-MINF) Note: The Painting of clamps with one coat of redoxide paint before fixing shall deemed to be included in the Quoted unit rate. The contractor should submit LM79 and LM80 test certificates of the manufacturers for the batch of light fittings supplied.

S&F 20W Surface/Wall mounted Batten LED Luminaire, extruded aluminium housing with PC diffuser and integrated electronic driver with high efficiency long life LED chips, CRI=80(Minimum) PF>0.95, System luminous efficiency >100 lm/Watt, Operating voltage 150V-270V including electrical connection with 3 Core flexible cable of appropriate size from ceiling rose to LED fitting complete all as specified and directed, fixed in repairs Make : Wipro Trim LED (LL20-281-XXX-65AL1/Philips (BN021C LED 20S PSU CW GR S2) or / Orient (LBLN-20-C-AL) /or BAJAJ (BLTRU 20W WH VIVA ) Note: The contractor should submit LM79 and LM80 test certificates of the manufacturers for the batch of light fittings supplied.

S&F 10/12W Recessed mounted round shape LED downlight with minimum efficiency 85 lumen/W, THD<10%, high reflective polycarbonate opal concave diffuser, high reflective polycarbonate opal conical shape reflector, high quality Die cast aluminium housing, input voltage 220-240V,CCT 5700K, input frequency 50Hz including electric connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to fixture complete all as specified and directed. Make :Wipro (LW01-101-XXX-60XX) /Philips (DN391B LED 6S-6500-PSU-WH) / GE Cat no 93057384/Bajaj Cat no BGCML12WWH Note : Cost of cutting and fixing in existing false ceiling deemed to be included in quoted rate.The contractor should submit LM79 and LM80 test certificates of the manufacturers for the batch of light fittings supplied. Note for all LED light fittings:- Incase of discrepancy between the description of items and the model number given, the model number shall prevail.

S&F 5star rated ceiling fan 1200 sweep and connecting upto and including provision of 23/0.0076 (for equivalent size in mm) flexible 3 core 1.5Sqmm PVC insulated copper conductor cable from ceiling rose to fan complete all as specified and directed. Make: Orient (Crown)/CG(HS Plus), Havells(ES-50)/Usha (VETRA)

S&F Energy Efficient Non metallic Fresh air fan 250mm sweep, Operating voltage 220-240V AC and frequency 50HZ, fixed as per manufacturers instructions and including electric connection using 3 core 1.5Sqmm flexible PVC insulated and PVC sheathed copper conductor cable complete all as specified and directed. Make: CG/Havells/ Bajaj/Orient/Usha

S&F MCB DB VTPN, 4way, Double door, IP 43, protection, with connected accessories like insulated busbars, insulated IP2X neutral bars & earth bar, blanking plates, cable management kit complete all as specified and directed.. (a) Incoming MCB 32A 4pole C series 10KA-01 Nos (b) Outgoing MCB SP 10 to 25 A, C series 10KA-01 Nos Make: Legrand/Schneider/Siemens

M&L Earthing complete with excavation and earth work in any type of soil with galvanized steel earth plate electrode size 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs below ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to GI earth strip 32 x 6 mm by means of bolts nuts check nuts and washers of galvanized iron, all as shown in electrical plate No.3 of MES SSR Part-1 connected to main switch board or main control board all as specified and testing on completion including provision of earth strip protected by galvanised iron 40 mm dia bore light grade pipe and watering pipe shall be 20 mm bore medium grade, PCC pit with pre cast RCC cover, charcoal / salt funnel etc. complete all as directed. NOTE : (1) The conctrete pit shall be PCC 1:3:6 tye C -1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with 8 mm TMT bars with suitable cast iron handle shall be provided (ii) Item includes the cost of 7.5 m GI pipe for protection of earth strip (iii) Item includes the cost of 7.5 mtr length earth strip 32 x 6 mm (iv) Result of earthing is not less than 2 Ohm

Supply and lay double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 ( Part I and II) for protection of underground calbes of size 63 mm outer dia with all fittings. laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc for cable protection all as specified (excavation and earth work shall be measured and paid separately) Make: Rex/Poly/Gemini

Supply, lay & test cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty)with stranded aluminium conductor, 1100 volts grade (Earthed ), of size 4 core 16 sq mm. all as specified and as directed by Engineer-in-Charge Make: havells/Plaza/Finolex

Supply and lay 25mm dia 3-layer PP-R Polypropylene random co-polymer) pipes SDR 7.4 11 UV stabilised and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches/fixed to wall or as site requirement, including fittings

Supply and fix PPR Gate Valves (Brass Insert) of 25 mm bore.

Making connection of PP-R distribution branch with PP-R main of 50-75 mm size by providing and fixing tee including cutting and making fusion joint etc

Parth Infrastructure Pvt. Ltd.

Sukhi Electricals

roxy enterprise

SURAJ ENTERPRISE

badri glass and construction

JAMNAGAR ELECTRIC AND MACHINERY CO