Rerouting Agasthyacodu feeder by using UG cable to avoid complex structure of Power house 4 pole under Electrical Section Punalur of Electrical Division Punalur

Providing one Earth using earth pipe incl. digging &backfilling pit and supply of charcoal, salt, sand etc

Fitting one Additional 2.4m/3m Channel cross arm (100x50x6mm), in existing 11KV DP incl. conveyance of materials.

Transporting poles by hired vehicle to a distance up to 5km and carrying up to 4 poles excluding loading & unloading

Additional rate for providing one disc set on any type of HT pole for making cut point

Excavation of cable trench in all clauses of soil and backfilling after laying of cable (excluding laying of cable)

Laying HT XLPE UG Cable (of sizes beyond 3x185 sqmm and upto and incl.3x300 sqmm)as per specification excl.excavation and backfilling

Fitting one Additional 75x40mm, 1.8m channel cross arm in existing single pole incl. conveyance of materials

Doing one cable end termination on cables of sizes beyond 3x185 sqmm and upto and including 3x300 sqmm using the cable jointing kit supplied departmentally

Loading HT A type pole from the stacking place and unloading the same at work site (transport by vehicle).

Fitting and erecting one HT A type pole in position incl. fitting cross arm, digging & back filling pit, drawing earth leads

Fitting and providing one HT stay for 11KV pole incl. digging and back filling pit

Stringing of one 11KV line with ACSR Racoon( 3 conductors) incl. cutting and removing tree branches wherever necessary.

Fitting one set AB switch and giving connection

Drilling hole of various sizes on existing Channel/Cross arm

Fitting and erecting one HT DP using A type pole in position incl. fitting 2 channel cross arms, digging & back filling pit, drawing earth leads

Providing stay for LT poles incl. digging & back filling pit

Dismantling ( without damage) one LT PSC/RCC pole after disconnecting stays, strut, etc. and stacking the same

Erecting one LT PSC pole in position incl. digging and back filling pit.

Providing concrete muffing (0.45x0.45x1.5m) inclusive of cost of all materials(as per specification)

Dismantling (without damage) one AB switch from existing structure and bringing back to section store

Mounting the cable ends of all sizes upto and incl.3x300sqmm with special type cable clamps incl.cost of extra materials if needed and giving necessary connections

additional rate for excavation of cable trench in exceptionally hard conditions ( like in ordinary rock)

Stringing of 11 kV Aerial Bunched cable of size 3x120+1x95 sqmm with bare/insulated messenger through existing poles

Erection of Anchor clamp/dead end clamp for 11 KV ABC of any size

Dismantling (without damage) one 11 KV PSC/RCC pole after disconnecting stays , strut etc and stacking the same

Dismantling (without damage) one Km LT 3 ph 4 wire OH line , cross arms, insulators and stacking the conductors in rolls

Dismantling (without damage) one Km LT additional conductor line, cross arms, insulators and stacking the conductor in rolls

Stringing one Km LT 3 ph 5 wire line (Rabbit for Ph and Weasal for N&St.main) incl, fitting cross arms etc removing touchings and conveyance of materials.

Dismantling one suspension clamp from 11 KV ABC

Dismantling one anchor clamp /dead end clamp from 11 KV ABC

Erection of suspension clamp for 11 KV ABC of any size

Dismantling of 11 KV Aerial Bunched Cable XLPE insulated of size 3x120+1x95 sqmm with bare insulated messenger

Loading 3x300 sqmm XLPE cable from its place of storage to department lorry and properly without causing any damage to its insulation and make ready for transporting as per the direction of department officers.

Dismantling (without damage)one Km 11 KV line (3 conductors) , cross arm, insulators, disc, rolling the conductor and stacking

Doing straight joint of 3x300 mm2 11 KV XLPE cable very carefully observing directions of manufacturers and departmental staff including crimping of socket

Doing one cable end termination on HT ABC of sizes upto 3x150+1x120 sqmm

Fitting one no MVT on existing cross arm excluding termination work ( for one phase) of any rating for 11 KV AB cable