Annual repair and maintenance of office building Mechanical Sub-Division at Jail road District Mandi (H.P) (Sh- Providing and laying tile work, distempering, painting, water supply and sanitary installations work etcetera) (1st floor AN Ground floor

Demolishing cement concrete manually/ by mechanical means including disposal of material complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Dismantling tile work with any thickness in floors and roofs laid in cement mortar including stacking material complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (three hundred into three hundred millimetr) (thickness to specified by the manufacturer) of first quality conforming to IS : 15622 of approved make in colours such as white, lovery, gray, fume red brown, laid on 20mm (twenty millimetre) thick cement mortar 1:4 ( one cement : four coarse sand), jointing with gray cement slurry @ 3.3 Kg/sqm (at the rate of three point three kilogram per squaremetre) including pointing the joints with white cement and matching pigment etcetera complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying Vitrified tiles in 300x300mm (three hundred into three hundred millimetr) in size (thickness to be specified by manufacturer), with water absorption less than 0.08 % (zero point zero eight percent) and conforming to I.S. 15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm (twelve millimetre) thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (at the rate of three point three kilogram per squaremetre) including grouting the joint with white cement and matching pigments etcetera complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Repairs to plaster of thickness 12 mm (twelve millimetre) to 20 mm (twenty millimetre) in patches of area 2.5 (two point five) squaremeters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, with cement mortar 1:4 (one cement : four fine sand) including carriage of material within all leads and lifts and other incidentals complete and as per the entire direction and satisfaction of Engineer-in-Charge.

Distempering one or more coats on old work with oil bound washable distemper of approved brand and manufacture to give an even shade complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Removing dry or oil bound distemper, water proofing cement paint and the like by washing and scraping and sand papering the wall surface smooth including necessary repairs to scratches complete within all leads, lifts, carriage of material and other incidental complete in all respect as per direction of Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 1 mm (one millimetre) of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete within all leads, lifts, carriage of material and other incidental complete in all respect as per direction of Engineer-in-Charge.

Painting wood work with Deluxe Multi Surface Paint of required shade two or more coat applied @ 0.90 ltr/10 sqm (at the rate of zero point nine zero litre per ten square metre) over an under coat of primer applied @ 0.75 ltr/10 sqm (at the rate of zero point seven five litre per ten square metre) of approved brand and manufacture including carriage of material in all leads and lifts and other incidentals complete and as per the entire direction and satisfaction of Engineer-in-Charge.

Wall painting one or more coats on old work with plastic emulsion paint of approved brand and manufacture to give an even shade complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10(ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of material in all leads and lifts and other incidentals complete and as per the entire direction and satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china wash basin having size 630x450 mm (six hundred thirty into four hundred fifty millimetre) with C.I. brackets, 15 mm (fifteen millimetre) C.P. brass pillar taps, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of material in all leads and lifts and other incidentals complete and as per the entire direction and satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings complete including carriage of material in all leads and lifts and other incidentals complete and as per the entire direction and satisfaction of Engineer-in-Charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm(one hundred thirty eight millimetre), breadth 102mm (one hundred two millimetre), height of 75mm (seventy five millimetre) with concealed fitting arrangements, weighing not less than 106 gms (one hundred six grams) complete within all leads and lifts as per entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 15 mm(fifteen millimetre) nominal bore brass bib cock of approved quality complete within all leads and lifts as per entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing angle cock of superior quality complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm (two hundred fifteen millimetre) long, 200 mm (two hundred millimetre) wide with minimum distances of 37 mm (thirty seven millimetre) from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms (eighty eight grams) complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 100mm (one hundred millimetre) sand cast iron grating for gully trap complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) nominal bore with 45cm (forty centimetre) length unplasticised P.V.C. connection pipe with brass union of approved quality complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 32mm dia (thirty two millimetre diametre) semi rigid P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front one urinal basin of 430x260x350 mm (four hundred thirty into two hundred sixty into three hundred fifty millimetre) and 340x410x265 mm (three hundred forty into four hundred ten into two hundred sixty five millimetre) sizes respectively with 5 (five) litre white P.V.C. automatic flushing cistern with standard flush pipe and C.P. Brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) nominal outer dia chlorinated polyvinyl chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipe with clamps at 1.00 m (one metre) spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge. .

Providing and fixing 20mm (twenty millimetre) nominal outer dia chlorinated polyvinyl chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipe with clamps at 1.00 m (one metre) spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge. .

Providing and fixing 110mm (one hundred ten millimetre) diametre single socketed unplasticised Rigid PVC rain water pipes on wall face conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 150mm (one hundred fifty millimetre) diametre PVC offset complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Bend 87.5° (eighty seven point five degree)150mm (one hundred fifty millimetre) bend

Providing and fixing 110mmx90mm (one hundred ten millimetre into ninety millimetre) PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetera complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 20mm (twenty millimetre) nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 20mm (twenty millimetre) nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end) complete within all leads, lifts carriage of material and other incidental complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Please Enable Macros to View BoQ information