Construction of swimming pool in the premises of Malikheda Stadium in Amroha district under MP fund in the financial year 2025-26

Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-20 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :300 mm dia piles. DSR 20.3.1 But Excluding GST

Vertical load testing of piles in accordance with I. S. 2911 ( part iv ) including installation of loading plateform & preperation of pile head or construction of test cap & dismantling of test cap after test etc. complete as per specification and the direction of Engineer - in - Charge. Initial Test DSR 20.6.1.1 But Excluding GST

Vertical load testing of piles in accordance with I. S. 2911 ( part iv ) including installation of loading plateform & preperation of pile head or construction of test cap & dismantling of test cap after test etc. complete as per specification and the direction of Engineer - in - Charge. Routine Test DSR 20.6.1.2 But Excluding GST

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. 2.6.1 All kinds of soil. DSR 2.6.1 But Excluding GST

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR 4.1.8 But Excluding GST

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. DSR 2.27 But Excluding GST

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: 2.35.31 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. DSR 2.35.3.1 But Excluding GST

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).bands, slab & Beem Ground Floor DSR 5.3 But Excluding GST

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) DSR 5.1.2 But Excluding GST

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) Ground Floor DSR 5.2.2 But Excluding GST

Brick work with common burnt clay (non modular) bricks of class designation 150 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) DSR 6.1.2 But Excluding GST

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) DSR 4.10 But Excluding GST

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. D.S.R.-4.13 But Excluding GST

Brick work with common burnt clay (non modular) bricks of class designation 150 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) Ground Floor DSR 6.4.2 But Excluding GST

Brick work with common burnt clay (non modular) bricks of class designation 150 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) Ground Floor DSR 6.4.1 But Excluding GST

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Ground Floor DSR 5.22.6 But Excluding GST

15 mm thick plinth plaster [1 cement : 4 coarse sand] D.S.R.-13.5.1 But Excluding GST

15 mm cement plaster of mix 1:6 (1 cement: 6 coarse sand) Ground Floor DSR 13.5.2 But Excluding GST

12 mm cement plaster of mix 1:6 (1 cement: 6 coarse sand) Ground Floor DSR 13.4.2 But Excluding GST

12mm thick plaster in 1:3 on ceiling and soffits of stairs upto floor two level. Ground FloorPWD-13.16 But Excluding GST

Making grooves 10 to 12mm wide x 8 mm deep in plaster of the walls or in ceiling vertically or horizontally as required. DSR 5.30 But Excluding GST

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600x600 mm Ground FloorDSR 11.41.2 But Excluding GST

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Ground Floor DSR 11.46.2 But Excluding GST

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm thick. Ground Floor DSR 11.26 But Excluding GST

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. Ground Floor DSR 11.27 But Excluding GST

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. Ceramic Tilse Floor tilse DSR 11.37 But Excluding GST

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. DSR 8.31 But Excluding GST

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red. DSR 8.2.2.1 But Excluding GST

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size stone aggregate. DSR 11.3 But Excluding GST

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. Single leaf DSR 9.20.1 But Excluding GST

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. DSR 10.31 But Excluding GST

Providing and fixing in position collapsible steel shutters with channels 20x10x2 mm and braced with flat iron diagonals 20x5 mmverticalsize, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm diasteel pulleys, complete with bolts, nuts, locking arrangement, stoppers,handles, including applying a priming coat of approved steel primer. DSR 10.3 But Excluding GST

ANLAYSIS FOR ALUMINIUM DOOR CHAUKHATS But Excluding GST

Door Partition with aluminium Shutters But Excluding GST

Window with aluminium glass Shutters But Excluding GST

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer. Ground Floor DSR 13.41 But Excluding GST

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). Ground Floor (DSR-13.47.1) But Excluding GST

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Ground Floor DSR 13.80 But Excluding GST

Providing & fixing stainless steel door handles with screws and 150mm long.SI marked. But Excluding GST

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. DSR 22.7 But Excluding GST

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work. DSR 13.52.1 But Excluding GST

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture. DSR 13.48.2 But Excluding GST

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :4.0 mm thick glass panes. DSR 10.30 But Excluding GST

Brick work with common burnt clay (non modular) bricks of class designation 150 in foundation and plinth in:Cement mortar 1:4 (1 cement : 6 coarse sand) DSR 6.1.1 But Excluding GST

25 mm thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size stone aggregate. DSR 11.3.1a But Excluding GST

12 mm thick plinth plaster [1 cement : 4 coarse sand] D.S.R.-13.4.1 But Excluding GST

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Light shade pigment using white cement. DSR 11.20.1 But Excluding GST

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). DSR 10.28 But Excluding GST

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) including applying of twice ( at base and top of mortar ) cement slurry @ 2.2kg/m2 (each time) mixed with water proofing compound conforming to 1S:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sgm thoroughly embedded in the 2nd layer. DSR 22.1 But Excluding GST

Centering and shuttering including strutting, propping etc. and removal of form work for : Suspended floors, roofs, landings, balconies and access platform But Excluding GST

Centering and shuttering including strutting, propping etc. and removal of form work for : Lintels, beams, plinth beams, girders, bressumers and cantilevers. But Excluding GST

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases of columns, etc. for mass concrete But Excluding GST

Centering and shuttering including strutting, propping etc. and removal of form work for : Columns, Pillars, Piers, Abutments, Posts and Struts. But Excluding GST

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. DSR 17.1.1 But Excluding GST

Providing and fixing white vitreous china pedestal type water closet ( European type W.C. pan ) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid. DSR 17.2.1 But Excluding GST

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tappillar tap. DSR 17.7.4 But Excluding GST

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Felxible pipe 32mm dia DSR 17.28.1 But Excluding GST

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Felxible pipe 40mm dia DSR 17.28.2.2 But Excluding GST

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. DSR 17.31 But Excluding GST

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per |S : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever requiredRange of three half stall urinals with 10 litre P.V.C. automatic flushing cistern. DSR 17.5.3 But Excluding GST

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. RAIN WATER FIXTURES & ACCESSORIES : I 110 mm diameter DSR 12.41.2 But Excluding GST

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. COUPLER 110 mm DSR 12.42.1 But Excluding GST

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. TEE 110 mm DSR 12.42.2 But Excluding GST

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. BEND 110 mm DSR 12.41.5.2 But Excluding GST

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm DSR 12.43.2 But Excluding GST

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete. 110 mm DSR 12.22 But Excluding GST

Providing and fixing 100 mm diameter and 60 cm long rain water spout in cement mortar 1:4 (1 cement : 4 fine sand). DSR 12.37.1 But Excluding GST

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. WATER SUPPLY PIPES AND FITTINGS - III Internal work-Exposed on wall20mm dia nominal outer dia pipes DSR 18.7.2 But Excluding GST

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. WATER SUPPLY PIPES AND FITTINGS - III Internal work-Exposed on wall25mm dia nominal outer dia pipes DSR 18.7.3 But Excluding GST

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 16mm dia nominal outer dia pipes DSR18.8.1 But Excluding GST

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 20mm dia nominal outer dia pipes DSR18.8.2 But Excluding GST

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 32mm dia nominal outer dia pipes DSR18.8.4 But Excluding GST

Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions. 45 cm length 15mm nominal bore. DSR18.21.2.1 But Excluding GST

Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 15mm nominal bore DSR 18.49.1 But Excluding GST

Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15mm nominal bore DSR 18.51.1 But Excluding GST

Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 15mm nominal bore DSR 18.53 But Excluding GST

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore. DSR 18.18.3 But Excluding GST

Providing and fixing CP Brass Single lever lelephonic wall mixture of quality & make and as per thedirection of Enginer-in-charge. 15mm dia nominal dia. DSR 17.22B But Excluding GST

Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge. 15mm nominal bore. 15mm nominal bore DSR 17.16A But Excluding GST

Providing and fixing CP Brass 32 mm size Bottal Trap of approved quality & make and as per thedirection of Enginer-in-charge. DSR 17.22A But Excluding GST

Providing & fixing PTMT towl rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour. 600 mm. long towl rail length of 645 mm. width 78 mm. and effective height of 88 mm, weighing not less than 190 gms. DSR 17.73.2 But Excluding GST

Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing not less than 105 gms. DSR 17.71 But Excluding GST

Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.For 500 litres. DSR 18.48 But Excluding GST

Constructing masonry Chamber 60x60x75 cm inside, in brick work incement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.surface box 100 mm top diameter, 160 mm bottom diameter and 180 mmdeep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement: 1.5coarse sand : 3 graded stone aggregate 20 mm nominal size), includingnecessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plasteringwith cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finishedwith a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 SCHEDULE OF QUANTITIES FOR INTERNAL SEWERAGE SYSTEM - IV With FPS bricks of class designation 150 DSR 19.7.1.1 But Excluding GST

Constructing masonry Chamber 60x60x75 cm inside, in brick work incement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.surface box 100 mm top diameter, 160 mm bottom diameter and 180 mmdeep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement: 1.5coarse sand : 3 graded stone aggregate 20 mm nominal size), includingnecessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plasteringwith cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finishedwith a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 SCHEDULE OF QUANTITIES FOR INTERNAL SEWERAGE SYSTEM - IV Extra for depth of man hole size 600x750mm DSR 19.8.1.1 But Excluding GST

Supplying and fixing C.l. cover without frame for manholes :455x610 mm rectangular C.l. cover (light duty) the weight of the cover to be not less than 23 kg DSR 19.18.1 But Excluding GST

Haunching of SWR pipe 90mm or 110mm with pcc 1:5:10 cement concrete ( 1 cement:5coarse sand:10stone grit) DSR 19.2.2 But Excluding GST

Providing and fixing of UPVC SWR ring fit pipe of class B of ISI mark Confirming to IS code 13592 (make prince, supreme finolex) in internal works of toilet and RWP etc. including fixing with rubber rings etc. including cost of all material, labour etc. complete. SOIL WASTE & VENT PIPES AND FITTINGS - II 110mm diameter. But Excluding GST

Providing and fixing of UPVC SWR ring fit pipe of class B of ISI mark Confirming to IS code 13592 (make prince, supreme finolex) in internal works of toilet and RWP etc. including fixing with rubber rings etc. including cost of all material, labour etc. complete. SOIL WASTE & VENT PIPES AND FITTINGS - II 90mm diameter. But Excluding GST

Supply and fixing of UPVC S.W.R. pipe nahni trap size 100x75,110/90 mm confirming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125 mm dia heavy duty CP brass jali. complete as per specification and the direction of Engineer - in - Charge but excluding GST

Supply and fixing of UPVC S.W.R. Cowel confirming to IS-14735. Size 75/90 mm Size 110 mm. complete as per specification and the direction of Engineer - in - Charge but excluding GST

Supply and fixing of UPVC S.W.R. UPVC pipe Type B CONFERMING TO IS 13502 Including jointing ring lubricant and UPVC SWR cupler conferming is to IS 14735 also including excavation of trenches cutting of wall and holes and repairing the wall floor and refilling the trenches as before but excluding supply and cost of other fitting such as elbow bend tee and y tee including all material labour and T&P Required for proper completion work. 150 mm O.D complete as per specification and the direction of Engineer - in - Charge but excluding GST

Wiring for light point/fan point/exhaust fan point/call bell pointwith 1.5 sqmm FR PVC insulatedcopper conductor single core cable in surface / recessed PVC conduit,with modular switch, modular plate, suitable G.I. box and earthing the point with 1.5 sqmm FR PVC insulated copper conductor single core cable etc. as required. DSR 1.10.1

Wiring for twin control light point with 1.5 sqmm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, 2 way modular switch, modular plate, suitable G.I. box and earthing the point with 1.5 sqmm FR PVC insulated copper conductor single core cable etc. as required. DSR 1.11 But Excluding GST

Wiring forcircuit / submain wiring alongwith earth wire with the following sizes of PVC insulated,copper conductor single core cable in surface/ recessed PVC conduit as required. 2 x 2.5 sq.mm. + 1 x 2.5 sq.mm. Earth wire DSR 1.14.2 But Excluding GST

Wiring forcircuit / submain wiring alongwith earth wire with the following sizes of PVC insulated,copper conductor single core cable in surface/ recessed PVC conduit as required. 2 x 4 sq.mm. + 1 x 4 sq.mm. Earth wire DSR 1.14.3 But Excluding GST

Wiring forcircuit / submain wiring alongwith earth wire with the following sizes of PVC insulated,copper conductor single core cable in surface/ recessed PVC conduit as required. 2 x 6 sq.mm. + 1 x 6 sq.mm. Earth wire DSR 1.14.4 But Excluding GST

Supply and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required 20 mm. DSR 1.21.1 But Excluding GST

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required 2 pair DSR 1.18.2 But Excluding GST

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet DSR 1.24.6 But Excluding GST

Supplying and fixing metal box of following size (nominal size) on surface or recess with suitable size of phenolic laminated sheet cover in fromt including paintingetc. as required. 5 mm x 75 mm x 60 mm deep DSR 1.22.1 But Excluding GST

Supplying and fixing following size / modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75 mmX75 mm) DSR 1.27.1 But Excluding GST

Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. DSR 1.26 But Excluding GST

Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing3 pin 5/6 amps. modular socket outlet and 5/6 amps. modular switch, connection, painting etc. as required. DSR 1.31 But Excluding GST

Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 & 5/6 amps. modular socket outlet and 15/16 amps. modular switch, connection, painting etc. as required. DSR 1.32 But Excluding GST

Supplying and fixing following way, three pole and neutral, sheet steel, TP MCB distribution board, 415 volts,on surface /recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators). 6 way (4 + 18), Double door, horizontal type DSR 2.4.2 But Excluding GST

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' series, miniature circuit breaker (MCB)suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. single pole DSR 2.10.1 But Excluding GST

Supplying & fixing single pole, blanking plate in the existing MCB DB complete etc. as required. DSR 2.11 But Excluding GST

Supplying and fixing following rating,four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps. DSR 2.13.2 But Excluding GST

Installation, testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq. mm. FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. DSR 1.45 But Excluding GST

Installation of exhaust fanupto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required. DSR 1.50.1 But Excluding GST

Extra for fixing the louvers / shutters complete with frame fro exhaust fans of all sizes. DSR 1.51 But Excluding GST

Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 m long etc, with charcoal/coke and salt as required. DSR 5.4 But Excluding GST

Supplying and laying25 mm x 5 mm. G.I. strip at 0.50 M. below ground as strip earth electrode, including connection and terminating with nut, bolt, spring, washer etc as required (jointing shall be done by overlapping and with 2 sets of brass nut bolt and spring washer spaced at 50 mm). DSR 5.9 But Excluding GST

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. DSR 5.16 But Excluding GST

Providing and fixing of circular / hexazonal cast ironor MS sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick MS sheetwith it top surface hacked for proer bonding, top lid shall be screwed into the cost iron/MS sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shal be made of 12 mm dia MS bar bent to shape as per standard drawing. DSR 10.18 But Excluding GST

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. DSR 14.14.1 But Excluding GST

Add for Invertor Wiring in wiring Point for light/Fan/Plug with 1.5 mm Cu Wire. DSR 189-A But Excluding GST

S/F of single light wall bracket (Cat-AAA) on matching M.D.F.E.G. board base etc. complete in all respects. Category AA DSR 412 But Excluding GST

S/F of recess/surface/pendent mounted 6 to 8 watt LED down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflector and driver set complete in all respect. Category AAA DSR 1401 But Excluding GST

S/F of LED Tube Light with batten suitable for up to 1x22 watt LED tube light fitting including tube on surface complete in all respect. Category AAA DSR 1413 But Excluding GST

Supply of ceiling fan with fan motor of AC permanent insulation, capacitor rating conforming BEE 5 star rating and IS : 374/79 and also comply with IS:1709/1984 with latest amendment the rated voltage 220/240 volts, 50 HZ single phase AC, the fan assembled should consists of down rod, blades, shackle canopies etc and with double ball bearing system. BEE 5 star rating - 1200 mm sweep DSR 1501(i) But Excluding GST

Supply & fixing of Crimping, solder, less, copper ton electroplated lugs of Dowel/ismail make suitable for 1.5 sqmm to 6 sqmm cables, including tapping with insulating tape, etc. complete in all respects. DSR 1129

S/F of sheet steel enclosure for DP / TP / FP MCB with neutral link and earth terminal. Cat-A DSR 1033 But Excluding GST

Supply & fixing of electronic Fan regulator (Modular), 120-280 V, ISI marked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of Engineer of work. DSR 1203-C But Excluding GST

Supply and laying of ISI marked aluminum conductor PVC / XLPE insulated armoured, served, sheathed cable 1100 volts grade at 750 mm below ground level over a cushion of 75 mm thick sand around & protected with brick on sides & top on surface the cable run shall be fixed on M.S. clamps etc. of suitable size complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 10 sqmm 4 core DSR 501 But Excluding GST

Supply and fixing brass nickel plated compression glands for PVC insulated armoured, served, sheathed cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth conductor. 10 sqmm 4 core DSR 503 But Excluding GST

Supply & fixing of plam or pin type copper tin plated cable socket (lug) to the cable leads, insulating with tape and making connections etc. complete in all respects as per direction of Engineer-in-charge. 10 sqmm DSR 504 But Excluding GST

Construction of recess distribution board of all sizes including cutting of brick work providing lintel of suitable size & thickness plastering etc. with supply of all materials, labours, T & P etc. required for proper completion of work. 600X480X200 mm. size. DSR 1141-B But Excluding GST

Supply and fixing of factory fabricated M.S. box in existing sunk with Godrej type almirah cover with handle etc. fabricated from 18 SWG M.S. sheet duly painted with red oxide primer followed by two coats of synthetic enamel paint complete with necessary conduit entry and DP/TPN; fixing arrangement and provision for compartment for loose wires, openable housing on the top and hold fast etc. including supply of all material, labour and T & P etc. required for proper completion of the work. 600X480X200 mm. size. DSR 1147

Supply of AC 230/250 Volts, 50 Hz 55w 1400 rpm exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required. 300mm sweep. complete as per specification and the direction of Engineer - in - Charge but excluding GST

Supply,instalation,testing, commissioning of 3 phase, KWH Meter with LCD display, RS pot, Wired Communication system with current limiter switch & reset button. (Make:-L&T) complete as per specification and the direction of Engineer - in - Charge but excluding GST

Self Priming(Commercial -HiFlow) Recirculation Pump with-in-Built Hair Strainer, SS Shaftand Non Corrosive Body of 4.0HP 3 Phase (2 Working 1 standby ) Make : ASTRAL/CERTIKIN / ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Totally anti corrosive Bobbin Wound Filter 1200m Dia, Fitted with pressure guage, manual air bleeder, water drain and emptying plug, collector arms and diffusers made from unplastcised PVC and Polypropelene with all accessories required. Working Presuure 2.5 Kg/Cm2 Make : ASTRAL / CERTIKIN / ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Side Mount Mult-Port Valvefor above complete as per specification and the direction of Engineer - in - Charge but excluding GST

Triple Grade White Silica Sand Media complete as per specification and the direction of Engineer - in - Charge but excluding GST

Electronic Memebrane Dosing Pump, can be mounted ontankor wall, following CE regulations, IP 65 protection, power connection220/240V,50/60 Hz.Material in contact with liquid are Prolypropelene, Viton, Teflon and PVC, includes anti plastic case, lubrication not required, Flow 10 Litres/ Hr @ 5 bar. Make : ASTRAL /CERTIKIN / AQUA complete as per specification and the direction of Engineer - in - Charge but excluding GST

Chemical StorageTank100 Litres capacity complete as per specification and the direction of Engineer - in - Charge but excluding GST

Pool Drains Grill in SS with SS Frame, Size 450 x 450mm Make : ASTRAL/ CERTIKIN / ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Floor lnlet Nozzles made in ABS with glue connections Diffuser type for uniform flow in all directionsMake: ASTRAL/CERTIKIN/ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Ladder in SS 304 width 500 mm with Ø 38 handrails.Stainless steel non skid steps with anchoring fixtures with 5 steps Make:ASTRAL/ CERTIKIN / ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Ladder in SS 304 width 500 mm with Ø 38 handrails.Stainless steel non skid steps with anchoring fixtures with 3 steps Make : ASTRAL/ CERTIKIN / ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Overflow Gratings 245mm width, with doublelock, to forma continousrun, Running Lengthon2 sides only Make:ASTRAL/CERTIKIN/ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Complete Set of Control & Regulatory Valves, NRV's Make : CEPEX/ZOLOTTO /PRINCE complete as per specification and the direction of Engineer - in - Charge but excluding GST

Life guard chair in SS with provision to hang 2 life buoys and wheels on two lags for mobility complete as per specification and the direction of Engineer - in - Charge but excluding GST

Life buoys complete as per specification and the direction of Engineer - in - Charge but excluding GST

SS Vacuum Head of 600mm length with Nylon Bristles and Rope connection But Excluding GST

Vacuum Hose with hose cuffs 30m Roll Make: ASTRAL/CERTIKIN/ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Extensible Aluminium Handle (3.6-7.2M) suitable to connect with all cleaning brushes and nets.Make: ASTRAL/CERTIKIN/ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Deep Bag Net Make: ASTRAL/CERTIKIN/ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Surface Skimmer Make: ASTRAL/CERTIKIN/ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GSTT

Metal Reinforced Plastic Curved Brush Make: ASTRAL/CERTIKIN/ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

SS Algae Brush Make: ASTRAL/CERTIKIN/ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Test Kit Make: ASTRAL/CERTIKIN/ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Pump for Suction Sweeper Of 2.0 HP mounted on Trolley, with Starter and 30 Metre Cable & Rope.Make: KIRLOSKAR/CROMPTON/AQVASTAR complete as per specification and the direction of Engineer - in - Charge but excluding GST

Complete PVCu Pipes and Specials of all sizes 63/75/90/110 /160/200 mm as required of 6Kg Pressure Ratings with Heavy Duty adhesives & Labour for pool,|balanc in gcham bers and plant room and drains Make ; SUPREME/ FINOLEX / PRINCE complete as per specification and the direction of Engineer - in - Charge but excluding GST

Starting Blocks made in SS Frame with non skid Fiberglass Top of size 500 x 500mm with anchoring fixtures Make:ASTRAL/AQVASTAR/CERTIKIN complete as per specification and the direction of Engineer - in - Charge but excluding GST

Float Lines with Anti Wave floats with fiber coated SS Wire and Lane Tighteners in each lane Make : ASTRAL/ CERTIKIN / ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

SS Cup Anchors to be embedded in side walls for Lanes Make : ASTRAL / CERTIKIN / ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Float Lane Rollers in SS Make : ASTRAL/ CERTIKIN / ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Under Water LED Surface Mounted Lights of 25 Watts, 12/24 Volts Cool/Warm White. Make: ASTRAL / CERTIKIN / ZODIAC complete as per specification and the direction of Engineer - in - Charge but excluding GST

Deck Box complete as per specification and the direction of Engineer - in - Charge but excluding GST

Heavy Duty Drivers for Lights to be placed in Plant Room complete as per specification and the direction of Engineer - in - Charge but excluding GST

Electrical Control Panel complete with Bus Bar, MCCB, MCB, Single Phase Preventor, Switches, Contactors Indicator Lamps, Wiring with clips, Voltmeter & all other required accessories. All components of reputed Makes like ABB/ Schneider/L&T or equivalaent. complete as per specification and the direction of Engineer - in - Charge but excluding GST

Wiring for Under Water Lights complete with conduits complete as per specification and the direction of Engineer - in - Charge but excluding GST

Wiring for Pumps, Dosing Pumps etc in Plant Room complete as per specification and the direction of Engineer - in - Charge but excluding GST

Installation, Commissioning, Testing of 3 HP Submersible sum Pump for above as per engineer incharge complete as per specification and the direction of Engineer - in - Charge but excluding GST

Please Enable Macros to View BoQ information