Repair/maint of external water supply at Zone B and Zone C under AGE E/M-I of GE Dehradun.

Amount

Material and labour for excavation in trenches in any type of soil not exceeding 1.5 Meter wide and not exceeding 1.5 Meter deep in any type of soil including cutting in slopes etc for laying of pipe line including getting out, complete all as specified and directed.

Material and labour for returning, filling in, including spreading, leveling, watering and well ramming in layers in soft / loose soil not exceeding 25 cm in each layer complete all as specified and directed by Engineer-in-Charge.

Material and labour for removal of excavated material (Soil) to a distance up to 50 Meter from starting point and depositing where directed at level not exceeding 1.5 Meter above as directed by Engineer-in-Charge.

Material and labour for dismantling electrically and taking down unserviceable fully automatic starter any type dry/ ATS type, from base frame and transporting to workshop for cleaning and refixing the serviceable parts back after repair and replacement of U/s parts for the 15 HP to 50 HP capacity size. (Note: Spare parts required for replacement shall be measured & paid for separately under respective item).

Material and labour for dismantling electrically and taking down unserviceable fully automatic starter any type dry/ ATS type, from base frame and transporting to workshop for cleaning and refixing the serviceable parts back after repair and replacement of U/s parts for the 75 HP to 125 HP capacity size. (Note: Spare parts required for replacement shall be measured & paid for separately under respective item).

The following spares parts shall be replaced for item no 4 & 5 here in above Make : L&T/Legrand/ABB/C&S

Auxiliary switch type -01 with 1 No-1 NC suitable for 75/125 HP star delta starter.

Supply & fix Motor Protection relay system for Thermal overload, Earth fault, Locked rotor, single phasing, current unbalance, phase sequence reversal and under current.

Supply and fix new three pole power contactor 240 volts 12Amp, any type complete all as specified & directed.

Supply and fix new three pole power contactor 240 volts 25Amp, any type complete all as specified & directed.

Supply and fix new three pole power contactor 240 volts 50 Amp, any type complete all as specified & directed.

Dismantling and taking out the existing corroded / scaled GI/ PPR/ PALP pipe with fittings connections from trenches, walls, ceiling or floor and removal from site or disposed off for the following sizes complete all as specifed and directed. Note: Excavation and earth work shall be measured and paid seperately under respective item of schedule "A"

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Supply, Laying, fixing & testing galvanished iron water tubing 'medium grade; ISI marked with and inclduing all GI fittings such as flanges, unions reducers sockets, socket reducing bends , elbows, tee, checkneuts, caps, plugs etc laid in trenches for the following sizes complete all as specifed and directed. Note: Excavation and earth work shall be measuered and paid seperately under respective item of schedule "A" Make : TATA/Jindal/Prakash

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

Taking out sluice valves refacing, regrinding and refixing of size 80 mm bore complete all as specified and as directed

All as per item No 10 here-in-before but 100 mm bore complete all as specified and directed.

All as per item No 10 here-in-before but 150 mm bore complete all as specified and directed.

All as per item No 10 here-in-before but 200 mm bore complete all as specified and directed.

All as per item No 10 here-in-before but 250 mm bore complete all as specified and directed.

All as per item No 10 here-in-before but 300 mm bore complete all as specified and directed.

Material and labour for any type of structural steel sections , MS flanges, nut- bolt, washers, sheets, back plate, xpm mesh, wire mesh, bending, cutting in shape, welding, drilling holes, flanges including painting with two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

Dismantling/taking out defective Gun metal gate valve and S&F for Gun metal gate valve with iron wheel head by screwing/cutting of existing pipe lines for the following size complete all as specifed and directed. Make : Kartar/Seiko/KARTAR

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Demolition the old existing valve chamber of size 60x60x60cm to 80x80x80cm and construct of new brick masonry valve pit of internal size 60x60x60cm to 80x80x80 cm with 230mm thick brick wall built in cement mortar 1:4 PCC 1:3:6 and plastering 15mm wall sides in cement mortar 1:4 and the pit covered with MS plain sheet 3 mm thick duly fixed to MS angle iron of size 40x40x3mm and duly embedded in plain cement concrete coping 5 cm thick in plain cement concrete 1:2:4mm type B1 (using 20 mm graded stone aggregate) with opening and locking arrangements including painting with two coat of synthetic enamel paint over one coat of primer complete all as directed by Engr-in-Charge.

All as per item no 18 here-in-before but size of valve pit 90x90x90cm to 110x110x110 cm complete all as directed.

All as per item no 18 here-in-before but size of valve pit 120x120x120cm to 150x150x150 cm complete all as directed.

Taking down old u/s sluice valve of any size and Supply and fixing CI sluice valve non rising spindle both end flanged dully drilled for both ends with stainless steel spindle and nuts stuffing box, hand wheel etc type PN - 1.6, ISI marked of following sizes:- Make : Kartar/kirloskar. Note:- Old unserviceable sluice valve shall be depost to MES store yard with out any extra cost.

80 mm bore.

100 mm bore

150 mm bore

200 mm bore

250 mm bore

300 mm bore

Supply and fixing in replacement CI Non return valve flanged ends ISI marked as per IS-5312 complete with Nuts/Bolts and washers and rubber packing etc for the following sizes:- Make : Kartar/kirloskar/BIR

200 mm bore

150 mm bore

100 mm bore

80 mm bore

Supply and fixing in replacement new foot valve, One end flanged and strainer to the other side ISI marked for the following sizes:- Make : Kartar/kirloskar/BIR

80 mm bore

100 mm bore

150 mm bore

200 mm bore

Supply & fix in replacement water pressure gauge glycerin filled of size 100 mm 0-7 kg/cm2 complete all as specified & Directed. Make : H Guru or equivalent

Taking down old U/S ampere meter from existing panel board and M&L for new ampere meter 144 x 144 mm for three phase AC supply with complete wiring connections all as directed. Make :- Legrand/Seimens/C&S/Schenider.

Taking down old U/S volt meter from existing panel board and M&L for new volt meter 0-500 volt for three phase AC supply with complete wiring connections all as directed. Make :- Legrand/Seimens/C&S/Schenider.

Material and labour for restoration of water supply by identifying and rectifying the water supply leakage repair work, at any location, in any type of leakage i.e. 15mm/ 20mm/25mm dia pipes of GI/ MS/PPR with any type of joints i.e. flanged, socketed,welding joint, including required fittings such as socket/ union/ long screw/ nipple, by cutting/ threading as required at site and as directed. Earth work (if required) will be measured in the quoted rate of this item. Note : (i) Any material required for leak repair deemed to be included in the above quoted rate. (ii) Any length of pipe required shall be paid sepertately under relevant item.

Material and labour for restoration of water supply by identifying and rectifying the water supply leakage repair work, at any location, in any type of leakage i.e. 40mm / 50mm/ 80mm/pipes of CI/ GI/DI/MS with any type of joints i.e. flanged, socketed, tyton rubber ring, welding or lead joint, D Joint, mechanical joint including required fittings such as socket/ union/ long screw/ nipple, by cutting/ threading as required at site , chocking of lead with spun yarn or providing new gasket / rubber ring/ nut bolts/ required welding work as per site requirement complete all as specified and as directed. Earth work (if required) will be measured in the quoted rate of this item. Note : (i) Any length of pipe required shall be paid sepertately under relevant item. (ii) Any material required for leak repair deemed to be included in the above quoted rate.

All as per item No 28 here-in-before but of size 100mm / 150mm pipes complete all as specified and directed.

All as per item No 28 here-in-before but of size .200mm / 250mm pipes complete all as specified and directed.

All as per item No 28 here-in-before but of size 300mm pipes complete all as specified and directed.

Material and labour to attend day to day electrical complaints of water supply installations by skilled electricians to carryout maintainence of LT panel, Star Delta Starters, security lights, checking of pumpsets, chlorinators, DG sets, replacement of burn out lugs etc

Disconnecting and taking down unserviceable electric motor of capacity 100 HP 1450 RPM 3 Phase from base frame and shifting to workshop for rewinding & replacement of unserviceable bearing, opeing compete taking out Rotor assembly from starter carefully and cutting/cleaning burnt winding wire from startor, carefully reapirs to demage slots sinclduing Rewinding of starter with super enameled copper wire gauge same as original & Varnishing the same drying tapping with cotton tapes all electrical cionnections should be soldered properly, reassembling resifting, reinstallation & one coat of synthetic enamel paint at site inclduing testing at full load complete all as specifed & directed.

All as per item No. 33 here-in-before but 75 HP 1480 RPM 3 Phase complete all as specified & Directed.

All as per item No. 33 here-in-before but 50 HP 1480 RPM 3 Phase complete all as specified & Directed.

All as per item No. 33 here-in-before but 40 HP 1480 RPM 3 Phase complete all as specified & Directed.

All as per item No. 33 here-in-before but 25 HP 1480 RPM 3 Phase complete all as specified & Directed.

All as per item No. 33 here-in-before but 20 HP 1480 RPM 3 Phase complete all as specified & Directed.

All as per item No. 33 here-in-before but 15 HP 1480 RPM 3 Phase complete all as specified & Directed.

All as per item No. 33 here-in-before but 10/12.5 HP 1480 RPM 3 Phase complete all as specified & Directed.

All as per item No. 33 here-in-before but 5/7.5 HP 1480 RPM 3 Phase complete all as specified & Directed.

All as per item No. 33 here-in-before but 0.5/3 HP 1480 RPM 3 Phase complete all as specified & Directed.

Supply and fix bearing suitable for electric motor 100 HP to 125 HP complete all as specified and directed.. Make - SKF/Tata/NBC

Supply and fix bearing suitable for electric motor 75 HP complete all as specified and directed. Make - SKF/Tata/NBC

Supply and fix bearing suitable for electric motor 40 HP to 50HP complete all as specified and directed.. Make - SKF/Tata/NBC

Supply and fix bearing suitable for electric motor 12.5 HP to 25 HP complete all as specified and directed.. Make - SKF/Tata/NBC

Supply and fix bearing suitable for electric motor 3 HP to 7.5 HP complete all as specified and directed. Make - SKF/Tata/NBC

Taking down centrifugal pumping set from base frame including disconnection of inlet suction and discharge pipe line, pump coupling for Centrigugal Pump Set discharge.-216 cum/hr at 130 Mtr head, 100 HP and shifting to workshop for repair and opening dismantling and overhauling complete parts, all parts cleaned by Kerosene oil neatly with and including replacement of defective spare parts by news parts including necessary welding machine/ grinding work if required at the time of refitting of spare into pump set and re-shifting, reinstallation on base frame with proper alignment with motor, one coat of synthetic enamel pain and testing on full discharge complete all as specified and directed. Note:- (i) Spare parts which are required to be replaced during repair shall be measured and paid separately in after as supply only rates,however fixing element shall be deemed to be included in the quoted rates of this item. (ii)Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required.

Supply only following spares parts to be replaced as repair to centrifugal pumping set multi stage type discharge.-216 cum/hr at 130 Mtr head, 100 HP complete all as specified and directed. Make:- Kirloskar under item No 48 here in above:-

CI impeller

SS sleeve

CI bush

MS coupling complete with rubber tyre/ Star rubber bush complete. make:- Love Joy/ Unic/ Unimax/ Unique/ Gemini

CI neck ring

Ball bearing

Pump bearing housing

Gland pusher

Double check nut with studs complete

Impeller Key

Housing bush

Pump Shaft

MS coupling cover complete with nut bolt

Interstage ring

Seal stud packing O ring

Wear ring

Taking down centrifugal pumping set from base frame including disconnection of inlet suction and discharge pipe line, pump coupling for Centrigugal Pump Set of 50 HP to 75 HP and shifting to workshop for repair and opening dismantling and overhauling complete parts, all parts cleaned by Kerosene oil neatly with and including replacement of defective spare parts by news parts including necessary welding machine/ grinding work if required at the time of refitting of spare into pump set and re-shifting, reinstallation on base frame with proper alignment with motor, one coat of synthetic enamel pain and testing on full discharge complete all as specified and directed. Note:- (i) Spare parts which are required to be replaced during repair shall be measured and paid separately in after as supply only rates,however fixing element shall be deemed to be included in the quoted rates of this item. (ii)Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required.

Supply only following spares parts to be replaced as repair to centrifugal pumping set of 50 HP to 75 HP of any make under item No 50 here in above:-

CI impeller

SS sleeve

CI bush

MS coupling complete with rubber tyre/ Star rubber bush. make:- Love Joy/ Unic/ Unimax/ Unique/ Gemini

CI neck ring

Ball bearing

Pump bearing housing

Gland pusher

Double check nut with studs complete

Impeller Key

Housing bush

Pump Shaft

MS coupling cover complete with nut bolt

Taking down centrifugal pumping set from base frame including disconnection of inlet suction and discharge pipe line, pump coupling for Pumping Set Centrifugal of 20/25 HP and shifting to workshop for repair and opening dismantling and overhauling complete parts, all parts cleaned by Kerosene oil neatly with and including replacement of defective spare parts by news parts including necessary welding machine/ grinding work if required at the time of refitting of spare into pump set and re-shifting, reinstallation on base frame with proper alignment with motor, one coat of synthetic enamel pain and testing on full discharge complete all as specified and directed. Note:- (i) Spare parts which are required to be replaced during repair shall be measured and paid separately in after as supply only rates,however fixing element shall be deemed to be included in the quoted rates of this item. (ii)Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required.

Supply only following spares parts to be replaced as repair to Pumping Set Centrifugal, discharge of 20/25 HP, multi stage Make:- Kirloskar under item No 52.00 here in above:-

CI impeller

SS sleeve

CI bush

MS coupling complete with rubber tyre/ Star rubber bush. make:- Love Joy/ Unic/ Unimax/ Unique/ Gemini

CI neck ring

Ball bearing

Pump bearing housing

Gland pusher

Double check nut with studs complete

Impeller Key

Housing bush

Pump shaft

MS coupling cover complete with nut bolt

Taking down centrifugal pumping set from base frame including disconnection of inlet suction and discharge pipe line, pump coupling for Pumping Set Centrifugal of 12.5/15.0 HP Multistage and shifting to workshop for repair and opening dismantling and overhauling complete parts, all parts cleaned by Kerosene oil neatly with and including replacement of defective spare parts by news parts including necessary welding machine/ grinding work if required at the time of refitting of spare into pump set and re-shifting, reinstallation on base frame with proper alignment with motor, one coat of synthetic enamel pain and testing on full discharge complete all as specified and directed. Note:- (i) Spare parts which are required to be replaced during repair shall be measured and paid separately in after as supply only rates,however fixing element shall be deemed to be included in the quoted rates of this item. (ii)Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required.

Supply only following spares parts to be replaced as repair to Pumping Set Centrifugal of 12.5/15.0 HP Multistage Make:- Kirloskar under item No 54.00 here in above:-

CI sleeve

CI bush

CI neck ring

Ball bearing

Gasket packing set

Pump stud of stainless steel with nut

Taking down centrifugal pumping set from base frame including disconnection of inlet suction and discharge pipe line, pump coupling forCentrifugal pumping set , Discharge 42 to 72 Cum/ hr at 44 to 50 Mtr head , 7.5/10 HP.multistage. and shifting to workshop for repair and opening dismantling and overhauling complete parts, all parts cleaned by Kerosene oil neatly with and including replacement of defective spare parts by news parts including necessary welding machine/ grinding work if required at the time of refitting of spare into pump set and re-shifting, reinstallation on base frame with proper alignment with motor, one coat of synthetic enamel pain and testing on full discharge complete all as specified and directed. Note:- (i) Spare parts which are required to be replaced during repair shall be measured and paid separately in after as supply only rates,however fixing element shall be deemed to be included in the quoted rates of this item. (ii)Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required.

Supply only following spares parts to be replaced as repair to Centrifugal pumping set , Discharge 42 to 72 Cum/ hr at 44 to 50 Mtr , 7.5/10 HP multistage.Make:- Kirloskar under item No 55.00 here in above:-

CI sleeve

CI bush

MS coupling complete with rubber tyre/ Star rubber bush. make:- Love Joy/ Unic/ Unimax/ Unique/ Gemini

CI neck ring

Ball bearing

Gasket packing set

Pump stud of stainless steel with nut

Taking down centrifugal pumping set from base frame including disconnection of inlet suction and discharge pipe line, pump coupling forCentrifugal pumping set , Discharge 42 to 72 Cum/ hr at 44 to 50 Mtr head , 3/5 HP.multistage. and shifting to workshop for repair and opening dismantling and overhauling complete parts, all parts cleaned by Kerosene oil neatly with and including replacement of defective spare parts by news parts including necessary welding machine/ grinding work if required at the time of refitting of spare into pump set and re-shifting, reinstallation on base frame with proper alignment with motor, one coat of synthetic enamel pain and testing on full discharge complete all as specified and directed. Note:- (i) Spare parts which are required to be replaced during repair shall be measured and paid separately in after as supply only rates,however fixing element shall be deemed to be included in the quoted rates of this item. (ii)Contractor shall ensure water pipe lines sealed by blocking with dead flange for the repair period if required.

Supply only following spares parts to be replaced as repair to Centrifugal pumping set , Discharge 42 to 72 Cum/ hr at 44 to 50 Mtr , 3/5 HP multistage.Make:- Kirloskar under item No 57.00 here in above:-

CI sleeve

CI bush

MS coupling complete with rubber tyre/ Star rubber bush. make:- Love Joy/ Unic/ Unimax/ Unique/ Gemini

CI neck ring

Ball bearing

Gasket packing set

Pump stud of stainless steel with nut

Material and labour for cutting of metelled road for taking out old or laying of nerw pipe appx 35cm wide and 75 cm deep all as specified.

Supply and fix in replacement of u/s MCCB 250 Amps with terminals, breaking cap 36 KA 4 pole 415 V AC 50 Hz Make: Lexic Legrand (DPX)/ Schneider NSX/ L&T D sine/Simens 3 VL

Supply and fix in replacement of u/s MCCB 200 Amps with terminals, , breaking cap 36 KA 4 pole 415 V AC 50 Hz Make: Lexic Legrand (DPX)/ Schneider NSX/ L&T D sine/Simens 3 VL

Supply and fix in replacement of u/s MCCB 160 Amps with terminals, , breaking cap 36 KA 4 pole 415 V AC 50 Hz Make: Lexic Legrand (DPX)/ Schneider NSX/ L&T D sine/Simens 3 VL

Material and labour for fixing of clamps MS of size 150 mm dia, 150 mm width, 4 mm thickness incl nuts,bolts washers all as directed.

Material and labour for fixing of clamps MS of size 100 mm dia, 150 mm width, 4 mm thickness incl nuts,bolts washers all as directed.

Material and labour for fixing of clamps MS of size 80 mm dia, 150 mm width, 4 mm thicknessincl nuts,bolts washers all as directed.

Supply and fix in replacement cast iron 'Mechanical joint set complete of two flanged collar one no sleeve two nos rubber 'O' ring and nut bolts washers of suitable size for 250 mm bore CI/DI pipe complete including necessary cutting, grinding work to fix in pipe as directed. (Note:- Earth work required to clear the pipe shall be measured and paid separately)

All as per item No 66 here-in-above but of size 200 mm bore

All as per item No 66 here-in-above but of size 150 mm bore

All as per item No 66 here-in-above but of size 100 mm bore

All as per item No 66 here-in-above but of size 80 mm bore

Material and labour for earthing complete with galvanized steel plate electrodes of size 600mm x 600mm x 6mm thick buried directly in ground with earth pit not less than 2.25m deep below normal ground level with top edge of plate not less than 1.5 m below normal ground level connected to galvanized strip of 25x4 mm earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanized iron pipe 40 mm bore (light grade) including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm dia MS bar funnel wire mesh 20 mm bore galvanized iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR part 1 including testing on completion all as specified and directed. NOTE 1. The unit rate includes for protection pipe 40 mm dia and GI strip 32x6 mm from top of earth plate up to 7.5 meter above ground level.

Material and labour for painting of different sizes connecting pipes Valve pit chamber covers, rolling shutters and its related items including writing letters on pump motors etc at various installations as per colour code with one coat of primer and two coat of synthetic enamelled paint all as specified and directed

Material and labour for CI/DI fitting for spigot & socket end pipes such as Bends (any type, radius and angle), Tapers any type (Straight, bend, increasing, decreasing or double socket etc), Tee pieces single branch, `Y` junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs and mechanical joints any type etc upto 150 mm bore including removing/ dismantling of old CI fittings complete all as specified and directed.

All as per item No 73 here-in-before but of size 200 mm to 300 mm bore complete all as specified and directed.

Cutting of cast iron pipe mains 150 mm bore for insertion of tees, collars, sluice valves, etc including dewatering work required for working water pipe lines complete all as specified and directed.

All as per item No 75 here-in-before but 100 mm bore complete all as specified and directed..

Taking up or down GI/CI/MS pipe from trenches including dismentling & removing for disposal for the pipes of 150 mm bore complete all as specified and directed.

All as per item No 77 here-in-before but 100 mm bore complete all as specified and directed..

Supplying and laying in trenches DI pipe 150 mm bore, centrifugally cast, with spigot and socket end, class K7 ISI as per IS 8329 marked of the following bores complete all as specified and directed. Make : Electrosteel/TATA/Jindal

All as per item No 79 here-in-before but 100 mm bore complete all as specified and directed.

Material and labour for tyton rubber gasket joints for 150 mm bore complete all as specified and directed

Material and labour for tyton rubber gasket joints for 100 mm bore complete all as specified and directed

Recharging of remote water level indicator SIM card for one year (Rs. 200 per sim card/month X 2 SIM CARDS/DEVICE X 12 months = 4800)

Supply and fix in repair following spare parts of SS probe unit of water level indicator type DDS4 Make : SECO/Active controls

(a) SS wire for pulley 16 meter long

(b) Special Football

(c) Aluminium spring for tension (size 2" x 5"

(d) Micro switch with gear

Taking up or down MS pipe 200 mm dia including dismentling & removing for deposit to MES store yard

Supply and fix 300 mm dia MS pipe flanged including welding works, nut, bolts and washers complete all as direcrected by Engr-in-Charge

Taking up or down MS pipe 150 mm dia including dismentling & removing for disposal for the pipes complete all as specified.

Supply and lay MS ERW steel pipe heavy grade with all fittings laid in floors or fixed to walls and ceilings including cutting , welding etc of sizes 150mm dia complete all as specified. Make : Jindal/TATA/Electrosteel

Taking up or down MS pipe 100 mm dia including dismentling & removing for disposal for the pipes complete complete all as specified.

Supply and lay MS ERW steel pipe heavy grade with all fittings laid in floors or fixed to walls including cutting , welding etc of sizes 100 mm dia complete all as specified. Make : Jindal/TATA/Electrosteel

Supply and fixing 3 core twisted aluminium flexiable weather proof cable PVC insulated and unsheathed multistranded copper conductor of size 0.5 sq mm confirming to relevent IS complete all as specified & directed including taking out old unserviceable cable.

Material and labour 10 mm thick cement plaster on fair face of brick/concrete surface in cement mortar 1:3 finished even and smooth without using extra cement.

Supply and fixing in replacement butterfly valve 80 mm dia PN 1.6 , ISI marked, CI body, stainless steel stem complete all as specified and directed. Make:- KIRLOSKAR/CASTLE/KARTAR

Supply and fixing in replacement butterfly valve 100 mm dia PN 1.6 , ISI marked, CI body, stainless steel stem complete all as specified and directed. Make:- KIRLOSKAR/CASTLE/KARTAR

Supply and fixing in replacement butterfly valve with gear assembly 300 mm dia PN 1.6 , ISI marked, CI body, stainless steel stem complete all as specified and directed. Make:- KIRLOSKAR/CASTLE/KARTAR

Supply only LT rubber insulation mat for pump house of size 1 mtr x 3 mtr of thickness 10 mm as per sample

Material and labour for point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS grade in concealed PVC conduit 20 mm dia or higher size and with suitable size of sunk type cast iron or pressed steel terminal box 1.2mm thick, duly painted for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of the following. (Note: Colour code shall be maintained as per IE rule).

(a) One light point point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

All as per item No 97.04 (d) here-in-before but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

Supply and fix switch piano flush, button type 5 Amp SP 250 V AC complete all as specified & directed. Make : Anchor/Havells

Supply and fix switch piano flush button type 15 Amps SP 250 V AC complete all as specified & directed.

Supply and fix socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

Supply and fix socket outlet two in one three pin 5 Amp and 15 Amp 2 module 120 W flush type complete al as specified.

Supply and fix stepped type electronic fan regulator flush type two module 400 Watt on the existing phenolic laminated sheet etc as required.

Supply and fix in replacement sheet metal enclosures 240 volt with suitable rated bus bar for double door 8 way IP-43DB's lk-09suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall and making good disturbed surfaces complete all as specified and directed by Engr-in-charge . (MCBs shall be measured and paid separately)

Supply and fix MCB double pole 240 Volt 10 KA 40 Amp 'B' series conforming to ISI marked complete all as specified & directed.

Supply and fix MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed.

Supply and fix in replacement wall mounted tube light fitting (LED batten) 20 watt, PF> 0.9, high color rendering index (CRI) >90 and above operating voltage 140V-270V colour temp 6500K & lumen input output 100 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable fixed on wall/roof complete all as specified and directed. Make: Philips/Bajaj

Cutting the existing hard standing/ metal road of facilitate for laying of water pipe line and making good the disturbed portion to bring it to original condition with plain cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) all as specified and as directed.

Supply Installation of Digital Indicator unit, with Jumbo 5 Digit Red LED 7 segment display of 150 mm each, to be connected with the ultrasonic sensor. The unit shall have High and Low alarm to be set according to requirement based on levels indicated. It should be possible to calibrate the Indicator to display in percentage or liters, centimeters as required. Make : Active Controls/SECO cat No DDUS/ PHOTRON

Dismantling existing unserviceable parts of Raw water unit Line size 125 mm dia and refixing new part in repair including necessary nut/ bolts screw and connecting up complete for following items:-

New Solenoid switch complete all as specified and directed.

New Feedback unit consiting of limit switch unit and mounting complete all as specified and directed.

Hand wheel unit complete all as specified and directed.

Disconnecting the electric connection of Control panle for repair / servicing at at STP Anarwala.Control panel consist of Incoming MCCB - 01 No and outgoing control switches (straters) - 08 Nos :- (i) - Starter assembly for blower motor of 10 HP cap - 02 Nos, Starter assembly for Sludge pump - 02 Nos, (ii) Starter assembly for pumpset motor of 15 HP cap - 02 Nos, (iii) - Starter for FAB feed pump - 02 Nos. Contractor will check the all relays, contactor, MCB/MCCBs, Complete control wiring and replace the same if found faulty. Note :- (ii) Rate of replacement of new items is included in quoted rate by the contractor of this item. (ii) All T&P required for completion this job is the responsibility of the contractor. (iii) After completion this job contractor will check the functioning of the control panel to the Engr-in-Charge.

Supply and filling new transformer oil in Oil type starters installed at various pump houses all as directed by Engr-in-Charge.

Dismantling existing unserviceable parts of filter No 3 Backwash Inlet Line size 350 mm dia and refixing new part in repair including necessary nut/ bolts screw and connecting up complete for following items:-

Pneumatic operated on-off ball valve 350 mm dia with actuator unit complete all as specified and directed.

New Solenoid switch complete all as specified and directed.

New Feedback unit consiting of limit switch unit and mounting complete all as specified and directed.

Hand wheel unit complete all as specified and directed.

Ansh Enterprises

Friends fire Engineers