REPAIR TO COMPOUND WALL SECURITY FENCING AND FOOT PATH IN ZONE I AND DOMESTIC AREA AT TBRL RANGE RAMGARH

Amount

Site clearance incl. removing of vegetation growth, bushes including taking out from fencings etc. and removing the rubbish n exc. 50m as specified and as directed by Engr-in- charge. (Measurement shall be taken of ground area cleaned)

Dismantling of brick work built in cement mortar of any specification and in any position complete all as specified and directed.

Material and labour for brick work with sub class 'B' old size bricks built in CM (1:6) all as specified.

All as per serial item No 3.00 but except bricks

Taking down cement plaster of any description racking out joints hacking for key scrubbing down with water etc to receive plaster complete all as specified.

Material and labour for 15mm thick rendering on fair faces of brick wall or concrete surface in CM 1:4, surfaces finished even and fair without using extra cement on wall, all as specified.

Material and labour for 15mm thick rendering on fair faces of brick wall or concrete surface in CM 1:6, surfaces finished even and fair with out using extra cement on walls, all as specified.

Preparation of new plastered surface and applying two coats of cement base paint over a coat of white wash etc complete all as specified and directed.

Dismantling of reinforced, cement concrete / steel in fencing posts structs of any section embeded in concrete and making good disturbed ground. (Height including burried under ground shall be measured) complete all as specified.

Material and labour for RCC 1:2:4 Type B-1, using 20mm graded aggregate as in precast cement concrete fencing post & struts and similar articles including necessary forms or moulds and fixed in position complete all as specified.

Supply and fixing for mild steel work as in posts/struts in fencing including cutting, tops to shape as directed, drilling holes notching for wire etc, complete conforming toFe-290 Grade E-165 complete all as specified.

Material and labour mild steel TMT bars 10mm dia & over, cut to length bent to shape required including cranking bending spirally for hooping for columns, binding ends with MS wire (annealed) not less than 0.9mm dia etc all as specified.

All as per serial item No 12.00 here-in-before but 5 to 10mm dia TMT bars as in stirrups, spacers & binders, etc, all as specified

Material and labour for two coats of cement wash with Portland cement slurry to a smooth bodied opaque finish to RCC pre-cast concrete fencing post all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.

Material and labour for PCC 1:4:8 type D2 using 40mm graded stone aggregate to embedding the fencing post / struts complete all as specified.

Material and labour for cement concrete (1:2:4), type B-1, using 20mm graded mechanically crushed stone aggregate as in coping, bed block benching, kerbs stone, mud stop, rounded or chamferred on edges including necessary form work/moulds complete all as specified and directed.

Dismantling of mild steel work as in angle iron frames/grills mild steel bars etc complete all as specified and directed.

Supply and fixing mild steel work as in grill, framed guard bars and similar work conforming to Fe-290 Grade E-165 including welding if required etc, complete all as specified.

All as per serial item No 19.00 above but fixing only angle iron frames/grills, mild steel bars obtained from Item No 18.00 above

Demolition of reinforced cement concrete of any description in any position prodivided for precast RCC jallies etc all as specified and directed.

Material and labour precast cement concrete type B-0 (1:2:4) using 12.5mm graded stone aggregate for Jallies 25mm thick set in cement mortar 1:4 including all moulding frame all as specified and directed.

Dismantling of GI barbed wire fencings fixed in RCC/Steel fencing posts complete all as specified and directed.

Supply and fixing for GI 2 standed barbed wire2.24mm dia wire with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire. staples or steel pins etc as directed (Each line wire to be measured) complete all as specified.

All as per serial item No 24.00 above but except barbed wire

All as per serial item No 24.00 above but Restraining, resecuring including making good staples only.

Dismantling of existing chain link fencing of any mesh and size complete all as specified and directed.

Supply only chain link fencing, any size or type etc including provision of binding wire, all as specified

Fixing only chain link fencing including line wire, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire etc complete all as specified and directed.

Supply and fixing for MS round bars and flat iron and similar small articles conforming to Fe 410-0 or Fe 310-0, for fixing of chainlink fencing complete all as specified.

Supply and fixing for mild steel screw bolts (machine made) with hexagonal or square heads at one end & screwed the other to be fitted with washers and one hexagonal or square nut for 5 to 10mm dia of shank but length of bolt exc 10cm & n exc 15 cm long complete all as specified and directed.

Fe-410-W 432 (Gde.E-250) Part- I quality-A or Fe 290 (Gde -E-165 Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips .

Material and labour for preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

All as per serial item No 33.00 above but n.exc 10 cm in width or girth when unconnected with other painting or painted in a different tint

Material and labour for preparation of old painted steel surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Supply and fixing in repairs for concertina coil 2.64mm dia having a core wire high carbon spacing steel of high tensile strength as per grade of IS-4454 (Pt-I) with a low carbon steel strip punched tape 19mm wide, 0.5mm thick and series of knife edge sharp barbs/blades @ 25mm centre to centre punched all along the length on both the sides of strips at regular interval confirming to IS-513 complete all as specified and as directed by Engineer in Charge including dismantling.

Material and labour for 75mm thick CC type D-2 1:4:8 (40mm Agg) as in subbase.

Supply only sand for screed bed min 25mm thick for paving flooring.

Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade over sand for screed bed watering and consolidating complete. Note: sand will be measured separately.

Material and labour for PCC chequered tiles with grey cement and pigment 25cm X 25cm X 25mm thick set & jointed in neat cement slurry as in path, pavement, floors, etc. over 15mm thick screed bed CM 1:6 all as specified and directed.

Material and labour for PCC floors/hard standing laid in bays type B-2 1:2:4 mix 100mm thick finished even and rough using XPM impression with concrete green including necessary formwork complete all as specefied and directed.

D.N.Gupta and Sons

ALPHA ENGINEERS AND BUILDERS

KUKREJA ENGINEERS