Renovation works in HOD Room Conference room and storeroom seminar hall of Computer Science Department in AD2 Building IIT Hyderabad Kandi

Amount

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings ,including fixing the pipe with clamps at 1.00 m spacing.and taking connection from existing water pipe line ,This includes jointing of pipes & fittings with one step CPVC solvent cement & testing of joints complete as per direction of Engineer in Charge.

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

20 mm nominal dia Pipes

Providing and fixing at all floors Type A - SWR PVC pipes including all fittings such as plain and door bends, tees, elbows, equal and unequal junctions, heel rest sanitary bends, collars etc. confirming to IS13592, IS 14735, including jointing with solvent and providing necessary supports, clamps/MS brackets at specified intervals The joints of pipe and fittings shall be with drip seal jointing in exposed areas lik in shafts etc. and pasted type (solvent ) for all other locations all complete and as per directions of Engineer - in - charge.

50mm dia pipe, 6Kg/Sq.cm

Providing and fixing of CERA makeF8040204/Equivalent Make angle valve for inlet connection of wash basin etc. all complete as per direction of Engineer in Charge.

Providing and fixing of Brass balve valve of approved make to fix at main inlet line connection etc. all complete as per direction of Engineer in Charge.

Cutting holes up to 30x30 cm in walls including making good the same:

With common burnt clay F.P.S. (non modular) bricks

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Providing and laying solid concrete blocks masonry with block of M7.5 grade cement concrete block of required thickness as per drawing in superstrcture with RCC band and mullion as per structural detail in cement mortar 1:4 (1 cement : 4 coarse sand) all complete as per direction of Engineer. (The payment of RCC elements shuttering and reinforcement shall be made for separately).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form for

Suspended floors, roofs, landings, balconies and access platform

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Wall painting with acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Two coat

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.

Granite stone slab of colour black, Cherry/Ruby red

Area of slab Over 0.5 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.

Granite stone slab of colour black, Cherry/Ruby red

Area of slab Up to 0.5 sqm

Providing and fixing of CERA make CONCORD Snow white sink 550x425x180mm/Equivalent sizewith sink cock with 150 mm long swivel spout of Cera make F2013301/Equivalent of standard pattern including painting of fittings and brackets, cutting and making good the walls wherever require: etc. all complete as per direction of Engineer in Charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 0x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws@ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Providing and Installation of 500 X 500 mm size carpet flooring of up to 6mm thick of approved pattern&colourcombination and make including levelling required underneath with all accessories and adhesive etc transport, complete as per the directions of Engineering-In-charge.

Supply of skilled manpower for finshing works to floor area and other repair works all complete as per the directions of Engineer in Charge.

Supply of Unskilled manpower for helping to mason for finishing works and other repair works all complete as per the directions of Engineer in Charge.

Providing and fixing of Kitchen carcass under and above the counte by using Outer Surface: Acrylic 1.5mm(super glossy)(Brand: Euro-Pratik or equivalent) Outer Edge banding: Acrylic 1.5mm(glossy) Inner Surface: 0.8mm Fabric Liner(Brand: Virgo or equivalent) Inner Edge banding: pvc 0.8mm Ply: Century Bond 710 16mm (21 year warranty from the brand),Laminate/Acrylic pressing is done is 100T Hydraulic cold press Machine Edge banding is done with Edge banding machine for better finishing including all fittings,accesories etc,all complete. as per the directions of engineer In charge.

Providing and fixing of Kitchen Shutters under and above the counter by using Outer Surface: Acrylic 1.5mm(super glossy)(Brand: Euro-Pratikor equivalent) Edge Banding: Acrylic 1.5mm(glossy), All sidesBack Surface: 0.8mm Fabric Liner(Brand: Virgo or equivalent) HDHMR: Action Tesa 16mm HDHMR Hinges: Hettich Sensys soft close hinges(German made) Laminate/Acrylic pressing is done is 100T Hydraulic cold press Machine Edge banding is done with Edge banding machine for better finishing including all fittings,accesories etc,all complete. as per the directions of engineer In charge.

Providing and fixing of Anodized Aluminium shutters(color based on the design) with clear glass and Hinges Hettich Sensys soft close hinges including all fittings etc,all complete. as per the directions of engineer In charge.

Providing and fixing of Tandem draws from one of the best brand in market Blum or equivalent with required size and shape as per design including all handles, fittings etc,all complete. as per the directions of engineer In charge.

Providing and fixing of Quartz 20mm from Kalinga Black(Nero Diamante or equivalent)make Seamless laying on kitchen platform with double patti at the edge and seamless square rounding etc,all complete. as per the directions of engineer In charge.

Providing and fixing of Dado Tile laying on the space between the counter and unit above counter etc,all complete. as per the directions of engineer In charge.

Providing and fixing of Hindware Kitchen Sink 41"x20"x10" 304 grade stainless steel with drain plate,Hindware Single Lever Sink Mixer With Flexible Spout including all fittings of approved make etc,all complete. as per the directions of engineer In charge.

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 0x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws@ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing of Kitchen shuttedr under the counter by using Outer Surface: PVC 1mm(glossy/matte based on design choice) with 1.3mm edge banding Inner Surface/Frame: 0.8mm PVC Liner with 0.8 mm pvc edge banding Ply: Century Bond 710 16mm (21 year warranty from the brand) Hinges: Hettich Sensys soft close PVC pressing is done is 100T Hydraulic cold press Machine Edge banding is done with Edge banding machine for better finishing Work Details: 4" ply covered with PVC all sides will be used for the frame to with hold the doors ply covered with PVC all sides hung using Hettich sensys soft close hinges etc,all complete. as per the directions of engineer In charge.

UNEED SOLUTIONS PRIVATE LIMITED (BID ID -3226079)

P RAMKISHAN (BID ID -3225949)