SPECIAL REPAIR OF BLDG NO T-184 AND T-185 OF ACCOUNT SECTION, PROVN OF COVERED PATHWAY FROM BASANTAR COY LOC TO BASANTAR ANTE ROOM AND CERTAIN SANCTIONED WORK AT IMA DEHRADUN

Amount

Dismantling timber scantling 40scm and over in section in any position framed work complete all as specified.

M&L for brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 bricks including demolition complete all as specified and directed.

All as per ser item No above but except bricks complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 including demolition complete all as specified and directed.

M&L for PCC type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) as in surface channel and drain beds including all necessary form work including demolition complete all as specified and directed.

M&L for Extra performing fair finished drain or channels cement concrete girth not excedding 40 CM using extra cement including forms, mould, mitied/ stopped ends etc. complete all as specified and directed.

M&L for rendering 15 mm thick in two layer (10 + 5 mm) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions including taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etccomplete all as specified and directed. (Water proofing compound shall be measured and paid for separately).

M&L for 10 mm thick rendering on fair faces of brick works in cement mortar 1:6 finished even and smooth without using extra cement in cement mortar including taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Demolation of cement concrete on ground floor and paving n.exc 15cm thick (below or above ground level) complete all as specified.

M&L for PCC 75 mm thick type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) as in plinth protection laid in alternate pannels finished even and smooth without using extra cement complete all as specified and directed.

M&L for 75 thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregate) as in sub base for laying floor finishes complete all as specified and directed.

M&L for 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for 20 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for 10 mm thick rendering on fair faces of brick works in cement mortar 1:4 finished rough for receiving tiles as in dado complete all as specified and directed.

M&L for 7 mm to 8 mm thick non skid premium quality coloured ceramic tiles in floor (area of each tile exceeding 0.11 and not exceeding 0.18 sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for Coloured Vitrified tiles 9 to 10 mm thick premium quality (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of existing surfaces including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed. Note : The contractor shall have no claim on difference what so ever on shade/colour of tile.

M&L for Coloured durastone heavy duty vitrified tiles 9 to 10 mm thick Sq/rectangular tiles area of each tile not exceeding 0.18 Sqm as in floors set and jointed in neat cement slurry and pointed in clooured cement to match the surface including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed. Note : The contractor shall have no claim on difference what so ever on shade /colour of tile.

M&L for Cement concrete rich colored chequered tiles machine pressed with imported pigment smooth finish of size (300 mm x 300 mm or any size as approved 20 to 25 mm) thick set and jointed with neat cement slurry including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for 15 mm to 18 mm thick granite stone etc slab as in shelves/vertical surfaces/platforms set and jointed in neat cement slurry, pointed in colored cement to match the shade including rubbing of moulding and mirror polishing etc including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for Coloured glazed ceramic tiles size (300 mm x 600 mm x 7 mm/300 mm x 450 mm x 7 mm or 8 mm thick) set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments in vertical surfaces including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing)complete all as specified and directed. Note : Contractor shall have no claim on colour or shade what so ever on this account.

M&L for Sand cushioning under floors including watering and consolidation complete all as specified and directed.

M&L for Coloured machine pressed/vibro mechanically floated interlocking paver block any shape and size confirming to IS - 15658-2006 of 60 mm thickness, M-35 grade, with topping of cement mixed with imported pigment colour and shape shall be approved and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed by Engr-in-Charge. Make : ULTRA/ MODERN/RUCHI/ISI Marked.

M&L for Machine pressed (factory made) plain cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), kerb stone of any size, laid in trenches on edges of roads joints fitted in CM 1:4 including excavation in any type of soil, PCC bed, returning filling and removal of surplus soil to a distance not exceeding 50 m from the starting point complete all as specified and directed.

M&L for Rolled section/tubular section as in main and cross beams, purlins, rafters, posts where connected to common rafter and running rails etc confirming to Fe-410-W (Gde E-250) qualtiy 'A' complete all as specified and directed.

M&L for Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work,incl locking arrangement for water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified.

S&F 4 mm thick E-board false ceiling (Classic) including galvanised colour coated snap grid frame for false ceiling, size of grid 605 X 605 mm fixed with 1.6 mm dia GI wire suspenders one end tied to roof members and other end connected to main tee of grid framework by means of 4mm dia adjustable "J" hook consisting of two Nos washers and two nuts at 1.2 mtr centres all as specified and as directed by Engineer-in charge (size of main tee 38 mmX25 mmX 1.4 mm, cross tee 38 mm X 25 mm X 1.4 mm angle along walls 38 mm X 25 mm X 2.0 mm) and two coats of oil bound emulsion complete all as specified and directed including dismantling boarding any description fixed in any position with nails.

S&F pre-painted galvalume aluminium zinc coating GI based Plain steeel sheet 0.50mm thick an colour having tensile strength of 550 Mpa as in roof covering/ridge/cladding to wall fixed with self tapping screws all as specified ncluding dismantling asbestos corrugated or semi corrugated sheets as in roof covering including ridge etc

S&F pre-painted galvalume aluminium zinc coating GI based tile profile corrugated steeel sheet 0.50mm thick any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified ncluding dismantling asbestos corrugated or semi corrugated sheets as in roof covering including ridge etc all as specified

Supply only (LW+) water proofing liquid solution of Dr fixit/sikka or equivalent make complete all as specified and directed.

S&F MS drapery 20mm dia stainless steel including brackets and necessary fitting "as in repair" complete all as specified and directed by Engr-in-Charge.

S&F 15 mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches including taking up or down steel tubing complete all as specified and directed.

S&F 20 mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches including taking up or down steel tubing complete all as specified and directed.

S&F 500 ltrs capacity rotational moulded polythene water storage tanks (Triple layered ISI marked) cylndrical with closed top hoisted and fixed in position including dismantling water tank complete all as specified and directed.

S&F 20 mm bore brass float valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule "as in repair" complete all as specified and directed.

S&F in repair single piece Vitreous china any shade cascade floor mounted single piece water closet P/S trap with dual flush cistern for UF soft close slim seat cover, hinges fitting, conversion bend, fixing accessories set complete all as specified and directed. Make : Jaquar Cat part No OPS-WHT15753NS250UFSMZ/ Cera cat part No S1013105/Kajaria cat part No KB-3007

S&F Vitreous china full set pedestal type wash basin, white, flat back, size 585x450x220mm including bracket, CP brass waste coupling and waste pipe fixed in repair complete all as directed. Make : Jaquar Cat part No Jaguar FLS-WHT-5801 & 5301/Cera cat part No S2040112 & S2090107 or equivalent in Kajaria/Somany

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long.

S&F in repair Corner glass shelf assembly with bracket complete all as specified and as directed.

S&F in repair toilet paper holder with flap guard fixed to walls with chromium plated brass screws. Make : Cera/Jaquar/Somany

S&F in repair soap dish holder fixed to walls with chromium plated brass screws.

S&F in repair soap dispenser fixed to walls with chromium plated brass screws.

S&F CP brass hot & cold single lever basin mixer with 450mm long braided hoses cast copper alloy with centre hole for WHB complete all as directed by Engineer-in-charge. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series

S&F copper ally 15mm bore long body bib tap chromium plated fancy type with wall flange and aerator fixed in repair complete all as specified and directed. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series

S&F CP fancy type Angle valve 15mm dia (angle cock) cast copper alloy with wall flange. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series

S&F in repair CP Health faucet telephonic type with CP with 1.5m long flexible pipe.

S&F in repair brass chromium plated towel ring fixed with screw in wall complete all as specified and directed.

S&F in repair brass chromium plated towel rail, 600mm long.

S&F Viterous China urinal half stall type white including CP spreader, waster pipe etc. "as in repair" complete all as specified and directed.

S&F in repair PVC connection 15mm bore with PTMT nuts of length 450mm.

M&L for Two coats of oil bound distamper on new surfaces over and including a coat of primer and 2mm thick putty on internal walls complete all as specified and directed.

M&L for Two coats of synthetic enamel paint on new steel surfaces including preparation of surface over and including a coat of red oxide zinc chrome primer complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old/new surfaces all as per manufacturers instruction and directed by EIC

Taking down chowkats or frame with shutter (without taking of shutter off shutters from frame) exceeding 1.5 sqm and not exceeding 4 sqm each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and directed by Engineer-in-Charge.

All as per ser item No 54 above but not exceeding 1.5 sqm complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite ) soild door/ window Ceostory windows & other frame / chowkhat single/double patam of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Supension Grade) , calcium carbonate and natural fibers (wood powder / rice husk / wheaat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabbricated with miter joints after applying PVC solvent cement and screws with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withrawal strength of 2200 N cum , (Face) & 1100 N (Edge) , minimum compressive srength of 58 N/mm², modules of elasticty 900 N/ mm² and resitance to spread of flame of class A category with property of being termite / borer proof , water / moisture proof and fire retardant. and fixied in position with MS hold fast/ lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-In-Charge.(M.S. hold fast/ lugs or SS dash fasteners shall be paid fo separately ) . Note : For WPC solid door/ window frames , minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable . Variation in profile dimension on plus side shall be accepetable but no extra payment on this account shall be made.

S&F Providing and fixing factory made single extruded WPC (wood polymer Composite ) soild decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (suspension Grade ), calcium carbonate and natural fiber (wood powder/ rice husk / wheat husk) and non toxic additives ( maximaum toxicity index of 12 for 100 gms ) having minimum density of 650 kg/cum and screw whithrawal strenght of 1800 N (Face ) & 900 N (Edge ) , minimum compressive strength 50 N/mm² , modulus of elasticity 850 N/mm² and resistance to spread of falme of Class A category with property of being termite /borer proof , water/moisture proof and fire retardant . WPC to be laminated with PVC foil of minimum 14 microns thic of approved desing pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel but hinges of required size with necessary full body threaded star headed counter sunk S.S screws., all as per direction of Engneer-In -Charge . ( Note : Stainless steel but hinges and necessary S.S srews shall be paid seprately )

S&F 35 mm thick plain framed second class hard wood panelled factory made shutters (two panel or more panel) with lock rail and panel of 12 mm thick BWP commercial ply with size of rail and stiles as per IS 1003 (part-1) kin seasoned and chemically pressure treated complete all as specified and directed.

S & F Ist Class hard teak wood, Plain and semi circular at top chowkats & frame wrought rounded or chamfered put together with glue pinned atg joints and fixed including dismantling complete all as specified and directed

S&F aluminium powder coated door fixed on aluminium frame of section 47.62mm x 44.45x1.6 mm thick, shutter glazed with tinted glass (Modi Guard) 5mm thick fixed with rubber gasket and aluminium strips as per standard method also rubber gasket at frame so as to make air tight with cast type handle aluminium anodised of 150mm size 2 Nos (One on each side of shutter) with shutter bottom rail 150mm x 44.45mm x1.6mm thick section, middle and top rail 83.5mm x 44.45mm x 1.6 mm thick section, side style 83.5mm x 44.45mm x 1.6 mm thick section all as sper IS 737- 1986 fixed with aluminium (extruded section) hydraulic door closer egulated designation No-3 universal type and make with aluminium tower bolt arrangement of standard make with locking arrangement with 6 levers mortise lock(brass body) of size 100mm etc complete all as specified and as directed.

M&L for Powder coated Aluminium anodised three track shutter window (glazed and wire gauge) sliding with aluminium window frame or chowkat 1.5 mm thick aluminium anodised of size 100 mm x 44.5 mm and window shutter frames glazed and wire gauze (middle, toprail, bottom rail) and styles 1.5 mm thick aluminum anodised of size 44.5x44.5 mm incl aluminium grill,stinless steel wire mesh and all fitting such as rubber gasket aluminium glazing clips locking cabinet and 75 mm handle and including 5.5 mm thick frosted glass pane in panes fixed with rubber gasket and glazing clip/aluiminium beads aluminium tower bolt 75 mm 02 Nos , aluminium butt hinges 75 mm 02 Nos in each shutter aluminium handle 100 mm 01 No in each shutter incl all accessories complete all as specified and directed.

S&F 18-19 mm thick prelaminated colour WPC sheet for cabinet shutter and frame &fixed at site colour as approved by Engr-in- Charge complete all as specified

S&F auto closing hinges 35mm of 0 crank(KH001) OR 8 CRANK (kh-002) openable at 110 degree for cabinet shutter fixed in repair complete all as specified.

S&F Stainless steel handle 125mm size for cabinet shutter fixed in repair complete all as specified

S&F in repairs PVC sandwich wall Lining consisting of 5mm thick wood grains printed PVC sheet complete fixing at site as specified and directed.

S&F floor door stopper 140mm of brass body and tougue with hard steel nspring complete all as specified

S&F Fancy and decorative type 150mm long brass barrel, semi barrel and skeleton tower flush bolts type 2 and fixed in repair flush complete all as specified and directed.

S&F Fancy and decorative type 150mm long brass barrel, semi barrel and skeleton tower flush bolts type 2 and fixed flush complete all as specified and directed.

S&F 150 mm butt hinges, cast brass with mild steel hinge pin bright polished and fixed type B-11 complete all as specified and directed.

S&F Fancy and decorative type 300mm long brass sliding door bolt with sand or die cast brass hasp staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed in repair complete all as specified and directed.

S & F Fancy and decorative type 300mm long brass sliding door bolt with sand or die cast brass hasp staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

S & F Fancy type and decorative 150mm log extruded brass handles fabricated type polished fixed in repair complete all as specified and directed.

S & F Fancy type and decorative 150mm log extruded brass handles fabricated type polished complete all as specified and directed.

S & F Aluminium body heavy duty double action floor spring suitable for glass shutter at both side rotable complete all as specified and directed.

S & F Aluminium door closer hydraulically regulated universal type, suitable for door shutters complete all as specified and directed.

M&L for repair by dismantlig of existing wooden floor and provide new HDF laminate wooden flooring of 15 mm thick over 2 mm thick Foam sheet over a layer of polythene film sheet over and including wooden fillets of size exc 16 sqcm but not exceeding 25 sqcm and all necessary fixtures to match with existing floor level and finished top finished floor. completed all specified and directed.

S&F Collapsible steel gates, top hung , consisting of channel pickets , pivoted flat bars , top and bottom runners, brass handles etc , as specified, erected in position and securing runners with holdfasts and brackets , complete all as specified and directed.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc and getting out in soft/loose soil complete all as specified and as directed.

M&L Plain Cement concrete 1:4:8 (type D2) (40mm graded aggregrade) in foundations, filling and mass concrete.

Returning, filling in, including spreading, levelling watering and well ramming in layers not exc 25 cm depth in soft/loose soil

Removing excavated soft/loose soil n. exc 50 m and depositing where directed

M&L RCC M-25 (Design mix ) in foundations, filling, Plinth beam and finished surface concrete flat.

M&L RCC M-25 (Design mix ) in Columns, pillars, piers, posts and struts and finished conctrete surface flat.

M&L for RCC M-25 (Design mix ) as in slab/slopping roof slab supported on walls, beams and column in floors, roofs, landings, balconies shelves etc and finished conctrete surface flat..

M&L for cement concrete M-25 (Design mix ) in roof beams ,floor beam etc and finished conctrete surface flat.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90mm dia or securing with clips.

M&L for TMT bars 06 to 8mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90mm dia or securing with clips.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter Rough finished flat

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions

M&L for Formwork to soffits of suspended slabs such as landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for Formwork to sides and soffits of floor or roof beams, Landing beams etc.

M&L for Formwork to edges of concrete flats, treads, breaks in floors and roofs n exc 20cm wide and similar work etc.

M&L for brickwork with sub class B bricks (old site brick) straight or curved on plan to any radius built in cement mortar 1: 6 complete as specified and as directed.

M&L for Pre-cast RCC 35 mm thick 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in louvers and jallies set in cement motar 1:4 including all mouldings and painting both sides , complete all as specified and directed.

M&L for 40mm thick PCC cement concrete ,1 :2:4 with 12.5mm graded aggregate mixed with WPC as per manufacturers instruction as in DPC work

M&L for one coat of blown bituminous of grade 85/25 @ 1.50kg/Sqm over DPC

M&L for polythene film,50 micron laid on PCC surface in DPC

M&L for rendering 15mm thick in CM 1:6 on brick/concretes on fair surfaces and finished even and fair without using extra cement

M&L for rendering 15mm thick in CM 1:4 on external sufaces on other than fair faces of brick work or concrete surfaces with WPC as per manufacturers instructions

M&L for rendering 5mm thick in CM 1:3 as in ceilings and finished even and fair without using extra cement complete all as specified

M&L for preparation of newly plastered surfaces and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and icluding priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new prepared surface complete all as specified including necessary scaffolding arrangement and as directed by Engr-in-Charge.

Material and labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over two coat of wall care putty of 1 to 2 mm thick and one coat of primer complete all as specified.

M&L for Preparation of new plastered or unplastered surfaces of ceilings to achieve smooth and even surface and applying three coats of white washing complete all as specified and as directed by Engineer-in-charge.

M&L, for roof treatment through manufacturer /authorized applicator of the manufacturer as approved by GE by applying a coat of cold applied bituminous oil based primer over cleaned surface @ 0.30 Kg/Sqm and laying of APP modified five layer polymeric membrane 3mm thick, minimum weight 3.60 kg/sqm reinforced with polyester non-woven fabric (weighing not less than 150 gms/sqm) with torch application method after a interval of minimum 8 hoursof hot bitumen coating by authorised applicator of manufacturer of IWL/STP/Texas India/ Hydrotech Ltd/Sikka, laid as per the manufactures instruction with side over lap of 75mm & end over lap of 100mm & tucked into the chases on vertical surfaces finally finished with bituminous aluminum paint @ 0.20 Kg/Sqm etc complete including taking down existing roof treatment of the RCC slab, cleaning off all foreign matter by wire brushing, cleaning off surface with water and removal of spoil etc including removal of debris from site beyond defence land,complete all as specified nand directed. Note :- 1. Work shall be carried out as per manufacturer's instructions by authorised applicator as approved. 2. Work shall be executed upto triple storied building. 3. The work shall be carried out in stages and each stage shall be passed by Engr-in-Charge and GE.

M&L for flooring with 100mm thick PCC (1:4:8 type D-2 using 40mm graded aggregate as in sub base and finished rough and fair

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

Cutting , grinding & refixing of existing terrazzo floor/ marble floor/ Kota stone floor surfaces (2 cut) on horizontal & vertical surfacewith 20 mm screed bed in CM 1:6 and finally finishing the surfaces uniformally by applying floor polish complete all as directed.

S&F Powder coated aluminium anodised door with frame and shutter and glazing 5mm thick glass and 12mm thick prelaminted particle board exterior grade in bottom panel (kit ply, novapan) glass fixed with rubber gasket with aluminium glazing clips, section of aluminium door shall be of following size :- Frame ; 100 x 44 x 1.98 mm glass thickness with rawal plug. Middle lock rail ; 150 x 44 x 1.98mm thick, Bottom rail ; 150 x 44 x 1.98mm thick, Top rail/Style : 85 x 44 x 1.98mm thick, Glazing beading : 0.70 mm thick , Aluminium handle `D' type 150mm, Aluminium tower bolt 9.9mm dia shoot 200mm long, Mortice lock - 100 mm 4 lever, aluminium stopper cleat - 02 Nos complete all as specified and directed.

S&F Powder coated aluminium Anodized frame for doors , windows, ventilators, partition wall with one or more rebates including joining cleat for fixing etc fixed ,complete all as specified. (Minimum thickness of powder coating not less than 50 micron) complete all as directed

S&F 5mm thick frosted glass fixed in aluminium door/window/partition fixed with rubber gasket and aluminium beading complete all as directed.

M&L 12 mm Non asbestos fibre cement,fire Resistance building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and directed.

M&L for double action floor spring hydraulically regulated made up of min 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in aluminium doors complete all as specified & directed.

M&L glazed vitrified tiles of any shade 8-9 mm thick (square/rectangular) polished, area of each tiles exceeding or equal to 0.36 sqm but not exec .42 Sqm, laid in floors etc. set and jointed in neat cement slurry and pointed with tile epoxy grout white or coloured to match the shade of tiles with and including 15 mm thick screed bed or bedding layer in CM 1:4 complete and demolition of existing floor and rubbish off outside the IMA premises complete all as directed.

S&F, Aluminium Powder coated three track sliding windowwith two or more shutter with 5mm thick plain glass one shutter of stainless steel mosquito proofing with good quality bearing, handle lock etc, rubber gasket and glazing clips etc using following sections as given in JINDAL catelogue.(a) Bottom rail sec no. 20620. (b) Top & verticle rails sec no. 20621,(c) Handle sec no.20606. (d) Inter lock sec no. 20724 (e) Top & bottom & sides sec no.20844 including PVC track, lock, U chanel and L alm angle cleats etc complete all as specified and directed. .

S&F in repairs for 5mm thick sandwitched PVC wall lining/panelling of any colour PVC sheet inclusive of PVC beads and angles at corners /edges and fixing at site with nails all as specified and directed.

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings converting window into door openings, built in cement mortar or cement lime mortar etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks removing surplus serviceable bricks, hard-core,etc. to store and rubbish not exc. 50m

Forming jambs cement mortar 1:4 etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete

S&F, Stainless steel curtain rod 20mm dia of SS conduit pipe grade -304 with end to end wall bracket,heavy duty brackets and decirative finials complete all as specified and directed.

S&F glass door stainless steel regular 6" (150 mm) lock for sliding glass with two moulded keys glass door lock complete all as specified and directed.

S&F slidig roller wheel 20mm diameter slotted wheel for book cases complete all as specified and directed.

S&F 5mm thick plain glass fixed in aluminium frame for bookcases complete all as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc.

Taking down old U/S main switches, Sheatmetal enclosures DB including MCCBs, MCBs etc including making good to the disturbed surface of wall all as directed.

Taking down old unsv T/L, Lamp,Security light of any size and capacity all as directed.

Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed.

Taking down carefully existing Exhaust fan/ cabin fan/ wall mounted / Ceiling fan from any height of any capacity by disconnecting the wire and set aside insafe custody for reuse and refixing in same positon after completion of work .

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

All as per item No 128 above but with stranded copper conductor 4 Sq mm (nominal area), two single core, PVC insulated cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated stranded copper conductor 4 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

Supply and fix modular switch 1 way 10A, 1 Module

Supply and fix modular switch 1 way 20A, 1 Module with indicator lamp

Supply and fix modular socket 10A, 2/3 pin combined 2 Module

Supply and fix modular socket 10A/20A, 2/3 pin combined 2 Module

Supply and fix modular fan regulators step type 2 module 120W .

Material and labour for ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate/isolated body complete all as directed.

Supply and fix in repir Sheet metal enclosure for DB`s SPN, with 200amps rated bus bar, 12 way, 240 volts double door Make Standard/HPL/Legrand, complete all as specified & as directed.

All as per item No 136 above but 8 Way DB SPN

All as per item No 136 above but 4 Way DB SPN

Supply and fix MCB SP 6 to 32 Amps 240 volts 10 KA C series. Complete all as specified & as directed

Supply and fix MCB SPN 40 to 63 Amps 240 volts 10 KA C series. Complete all as specified & as directed

Supplying, fixing & testing LED 34/ 36 Watts, 2' x 2' surface mounted ceiling light fitting, warm/ natural/ cool white as per requirement at site with glare free uniform illumination with electronic driver etc and all accessories pre wired including connecting to source complete all as specified & directed. Make- POLARIS NIO III LCTLSNE- 36 - FO- CDL Crompton/ PLUTO PANEL (SURFACE) of Havells or equipment in Philips as approved.

S & F LED Tube Light batten fitting 20/22 Watt of aluminium housing suitable for fixing on walls/ceiling, warm/natural/cool white as per requirement at site complete all as specified and directed by Engr-In-Charge.Make: BRIGHT LINEA of Crompton/LUMILINE PLUS NEO of Havells/ Essential SmartBright Batten of Phillips

Supply and fitting LED street light fitting 35 Watt 230 V AC outdor type with high presure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with iinpact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

S & F sub main wiring with 2 run PVC insulated unsheathed FRLSH cable 1100 Volt grade, with multi stranded copper conductor drawing in existing Concealed conduit including one run PVC insulated unsheathed cable with multi stranded copper conductor as a earth continuity and connected upto DB of following sizes complete all as specified and directed. Note:Two run of single core PVC cable with one run of earth conductor & condiut shall be measured as one unit.

4 x 16 Sqmm + 1 x 10 Sqmm

S&F LED 15 watt surface mounted round ceiling light fitting made of aluminium housing high translucent frosted plastic diffuser with glare free uniform illumination with electronic driver etc and all accesories pre-wired including connecting to source complete all as specified and directed by Engr-In-Charge.

S&F MCB SPN DB 2 way without busbar alongwith MCB SPN 6 to 32 amp complete with all accessories all as specified and directed by Engr-In-Charge.

S & F sub main wiring of description 2x2.5 sqmm + 1x2.5 sqmm with PVC insulated unsheathed FRLSH cable 1100 Volt grade, with multi stranded copper conductor drawing in and including rigid PVC conduit of size not less than 25 mm dia in concealed/surface as required at site including one run PVC insulated unsheathed cable with multi stranded copper conductor as a earth continuity and connected upto DB of following sizes complete all as specified and directed.

M&L Modular point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH having multi stranded copper conductor of 1.5 sq mm nominal cross sectional area drawn in and including non rigid PVC Conduit concealed in wall with all fitting not less than 25 mm dia and fixing accessories and 1.5 sq mm PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to earth dolly by providing suitable lugs with & including modular metal flush box of required size factory made for mounting Modular switch, regulators etc with and including Modular cover and frame , ISI marked

one fan point controlled by one one way switch 5 amps

All as per item No 146 above for point wiring for 5 pin switch socket outlet, 5/6 Amps on independent board complete all as specified and directed.

All as per item No 146 above for one power point 3 pin 15 Amps socket out let PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 4 Sq mm (Nominal area) including earth wire PVC insulated unsheathed 1100 volt grade cable with stranded copper conductor of size 4 Sq mm (Nominal area)cable common connected to earth dolly, all as specified for one 3 pin 15 amps socket outlet point controlled by one switch complete.

S&F Modular switch single pole one way 6/10 amp white in colour complete all as specified and directed by Engr-In-Charge. Make:Havells ORO(White)/ Legrand Lyncus/ Indoasian(Glint)

S&F Modular switch single pole one way 16 amp white in colour complete all as specified and directed by Engr-In-Charge. Make:Havells ORO(White)/ Legrand Lyncus/ Indoasian(Glint)

S&F Modular socket outlet 2/3 pin combined 2 module 16 amp white in colour complete all as specified and directed by Engr-In-Charge. Make:Havells ORO(White)/ Legrand Lyncus/ Indoasian(Glint)

S&F Modular socket outlet 2/3 pin combined 2 module 6 amp white in colour complete all as specified and directed by Engr-In-Charge. Make:Havells ORO(White)/ Legrand Lyncus/ Indoasian(Glint)

S&F plug and socket metal enclosure box of module (2P+E- SP), IK 08, supplied with Neutral Links complete with one MCB SP 20 amp,240 Volts recess mounted with chained metal cover for the socket outlet complete all as specified and directed by Engr-In-Charge.

S & F sub main wiring with 2 run PVC insulated unsheathed FRLSH cable 1100 Volt grade, with multi stranded copper conductor drawing in existing Concealed conduit including one run PVC insulated unsheathed cable with multi stranded copper conductor as a earth continuity and connected upto DB of following sizes complete all as specified and directed. Note:Two/Four run of single core PVC cable with one run of earth conductor & condiut shall be measured as one unit.

4 x 16 + 1 x 16 Sqmm

2 x 6 + 1 x 6 Sqmm

S&F MCB SPN DB 8 way double door with 200 Amp rated copper busbar, degree of protection IP 30, mechanical impact strength IK 08, attractive white shade matt finish having detachable gland plate suitable for surface mounting suitable for fixing MCB SPN as incomer and MCB SP as outgoing complete all as specified and directed by Engr-In-Charge.

S&F MCB TPN 'B' curve 63 Amp complete all as specified and directed by Engr-In-Charge.

S&F MCB SP 'B' curve 6 to 32 Amp complete all as specified and directed by Engr-In-Charge.

S&F wall mounted air ciculator fan 400 mm made of polypropylene material, number of blades 3, 100% copper winding,remote control,corded electric power source,aerodynamic blade design,thermal overload,protection for long lasting motor,high air delivery speed = 2100 RPM, air delivery = 105 cmm, input power = 125W complete all as specified and directed.

Supply and install hi wall split units inverter type 2 TR 3 Star indoor and outdoor complete with cordless remote control unit and with in built Heating and Cooling arrangement (Hot and Cold Type) suitable for R-32 refrigerant,operating range 10 to 50 degree Celsius,stabiliser free operations,copper condenser coils,auto air swing,auto clean function,sleep mode,PM 2.5 air filter, anti viral dust filter complete with all accessories all as specified and directed by Engr-In-Charge.Make: Voltas/Blue Star/LG

Supply and fix single phase voltage stabilizer (Copper wounded ) 5 KVA compatible for 2 ton split AC unit with voltage range 130V-300V with inbuilt thermal overload protection, intelligent time delay system,low and high voltage cutoff protection system complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-2 (using 40mm graded aggregate) as in plinth protection and finished the surface even and smooth without using extra cement

Pragati Enterprises (BID ID -3507928)

M/s Vinod Singh Negi (BID ID -3507711)

Bhanu Prakash (BID ID -3507773)

Meher enterprises (BID ID -3513494)