REPAIRS TO PERIMETER CHAIN LINK / BARBED WIRE FENCING, FOOT PATH, ROOF COVERING OF PARKING SHEDS, AREA DRAINAGE, CULVERTS, COVER SLABS AND PCC COPING AT VARIOUS LOCATIONS AND OTHER RELATED MISC WORK ETC IN OMQ, SMQ AND OTHER BUILDINGS IN DOMESTIC ARE

Amount

Demolition of brick work or stone / boulders / PCC block masonry built in Cement Mortar or cement lime mortar including all quoins, arches, pillars etc excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and as directed.

Demolition of Plain cement concrete of any description and in any position not otherwise specifically provided for, etc complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for etc complete all as specified and as directed. (Reinforcement cut as required to facilitate demolition)

M&L for PCC 1:4:8 type D-2 mix (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete etc complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry of PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:4 etc complete all as specified and as directed.

M & L for PCC 1:2:4 type B-1 mix (using 20 mm graded stone aggregate) as in copings / benching and finishing the exposed surfaces even without using extra cement etc complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces and rendering is to be finished even and smooth with out using extra cement complete all as specified and as directed.

M&L for Extra for forming fair finished drain or channels 30 cm to 60 cm inner girth in cement concrete, using extra cement , including forms, moulds, mitred / stopped ends etc complete all as specified and as directed.

M&L for Mild steel TMT bars 10 mm dia and over, cut to lenth, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for precast reinforced cement concrete 1:2:4, type B -1 mix (using 20 mm graded stone aggregate), as in cover slabs or in simillar works etc including necessary form work and set in CM 1:6, complete all as specified and as directed.

Excavating in trenches, for cleaning drains or in simillar works etc not exc 1.5 mtr wide and not exc 1.5 mtr in depth and getting out in soft / loose soil complete all as specified and as directed.

Returning , filling in including spreading, levelling , watering and well ramming in layers not exc 25 cm in soft / loose soil complete all as specified and as directed.

Removing excavated soil not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and as directed.

M & L for laying Reinforced cement concrete pipes, 300 mm dia, class NP-2, laid in trenches and jointed complete with collars, complete all as specified and as directed.

M&L for maintenance of drains of width not exc 60 cm by cutting all bushes, shrubs, and any type of vegetation, trees girth upto 30 cm etc. and desilting all deposits of soil and other materials upto 15cm high, to have a free flow of water and to get a uniform trapezoidal / rectangular shape of drain and getting out and removing all spoil to a distance not exc 500 mtr and deposited in layers not exc 25 cm thick, complete all as specified and as directed.

Dismantling existing fencing posts (RCC / wooden posts) of any description including embedded portion inside the ground, each not exc 0.5 cu mtr getting out and removing soil to a distance not exceeding 500 mtr complete all as specified and as directed.

M&L for plain cement concrete PCC 1:3:6 type C- 2 mix (using 40 mm graded stone aggregate) as in foundations, filling and mass-concrete complete all as specified and as directed

Dismantling existing barbed wire / plain wire / chain link fencing any type from RCC / Steel / Wooden posts etc complete all as specified and as directed.

Supply and Fixing of MS galvanised chain link fencing of mesh size 50 mm x 50 mm and 3.80 mm dia fixed to any type of fencing posts with straining bolts, stiffener rods etc including provision of binding wire as required etc complete all as specified and as directed.

M&L for precast reinforced cement concrete 1:2:4, type B-1 mix (using 20 mm graded stone aggregate), as in RCC fencing posts or in simillar works etc including necessary form work and set in CM 1:6 complete all as specified and as directed.

M&L for mild steel TMT bars 6 mm to 8 mm dia cut to length bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends for cover slabs, in pre cast works, etc and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and as directed.

M&L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for mild steel round bars 10 mm to 12 mm dia as required, made to shape for securing chain link fencing etc., and similar works conforming to Fe-290 Gde E-165 and including preparation and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer before fixing complete all as specified and as directed

S&F Rolled Mild Steel Framed works using flat iron, angle iron or other sections confirming to Fe- 410-W (Gde E-250) quality 'A', complete, including welding or bolting as per site reqirement, making holes wherever neccesary complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 15 cm and not exc 22.5 cm long, dia of shank 11 mm to15 mm complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. .

M&L for preparation of newly plastered surfaces of walls and applying two coats white wash etc complete all as specified and as directed.

M&L for hardcore of gauge not exc. 63 mm of broken stone boulders, deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M & L for 75 mm thick Cement concrete PCC 1:4:8 type D-2 mix (using 40 mm graded stone aggregate) as in sub floors , sub base floors and pavings etc complete all as specified and as directed.

M/L for 50 mm thick Sand filling under pavers, floors or in foundations etc including watering and consolidation compelete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver blocks with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade etc complete all as specified and as directed.

M&L for plain cement concrete PCC 1:2:4 type B-1 mix (using 20 mm graded stone aggregate) as in kerbs or mud stops, borders, etc,. rounded or chamfered on edges complete all as specified and as directed.

M&L for screed bed or bedding layer of cement mortor 20 mm thick for laying floor finishes in CM 1:4 complete all as specified and as directed.

M&L for Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick, set, jointed and pointed in neat cement slurry with grey cement and including pigments as in floors complete all as specified and as directed.

M&L for 100 mm thick plain Cement concrete PCC 1:2:4 type B-2 mix (using 40 mm graded stone aggregate) as in pavings etc complete all as specified and as directed.

M&L for Forming Construction joints 30 mm deep x 10 mm wide filled with sealing compound, Grade ‘A, complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete PCC 1:3:6 type C-1 mix (using 20 mm graded stone aggregate) as in top layers of plinth protection etc and finished even and smooth without using extra cement complete all as specified and as directed.

Dismantling existing Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridges, roof coverings / cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, cut to any size as per site requirements, fixed with self tapping screws etc complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, etc complete all as specified and as directed.

S&F Steel work in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS-1161- 1979 grade St.-240 etc complete all as specified and as directed.

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted stone walling, built in in CM 1:6 complete all as specified and as directed

M&L for Providing cement concrete PCC 1:2:4 type B-1 mix (using 20 mm graded stone aggregate) as in hold fast, copings on RCC or stone / brick wall or column to hold Y angles or similar works, bed plates, kerbs, and making good the surface, etc complete all as specified and as directed. (Note: - The PCC work is required to be done for posts where 'Y' angles has uprooted or where required without removing barbed wire, etc or any such removal will be made good without any extra cost)

M&L for Concertina coil super barb - bladed profile of dia 610 mm of weight not less than 8.50 kgs per coil of 7.5 mtr of length fixed to angle iron brackets or masonry surfaces with necessary accessories like straining wires, fixing clips etc complete all as specified and as directed. (Note :- Concertina coil shall be measured linearly of fencing length. The number of spirals shall not be less than 51 in 7.5 mtr length of each coil)

Removing and refixing existing old concertina coil of 2 feet dia weighing approx 8.5 kg / 7.5mtr or stacking already fallen concertina coil and refixing the same at position including stacking properly, restraining etc complete all as specified and as directed

Removing and Refixing of old existing Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings or untangle fallen old barbed wire and straining and refixing to any type of standard rails straining bolts, including making good , securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed (Note :- each line wire to be measured)

S&F in repairs, Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed (Note ;_ each line wire to be measured)

M/s RAMA LAKSHMI CONSTRUCTIONS

RAMESH ENTERPRISES