REPAIR TO ROOF, CHAJJAS, MISC B/R WORKS IN CERTAIN BLDGS AT VARIOUS LOCATIONS AND CERTAIN REPAIR/ MAINT OF MISC B/R WORKS AT ZONE A AND B AT PMS UNDER GE (ARMY) TRIVANDRUM

Amount

Dismantling single layer Mangalore pattern or similar tiles in roofing including ridge tiles complete all as specified and directed. Notes: All works under this BOQ will be executed for buildings of height up to four storeys. Contractor shall make all necessary proper scaffolding arrangements and safety measures for labours at site.

M&L for roof tiles, Mangalore pattern, interlocking at side joints, laid dry complete all as specified and directed.

All as per Sl No. 2 here-in-before, but except tiles complete all as specified and directed. Note: Serviceable tiles obtained from item No. 1.00 here-in-before will be reused under this item.

M&L for ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and directed.

All as per Sl No. 4 here-in-before, but except tiles complete all as specified and directed. Note: Serviceable tiles obtained from item No. 1.00 here-in-before will be reused under this item.

Demolition of cement concrete (unreinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

M&L for providing, cement concrete type B-0, 1:2:4 using 12.5 mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

Dismantling wooden fillets for roof tiles battens, rails, posts, rafters, purlins etc. under 40 sq.cm in section (unframed work) complete all as specified and directed.

M&L for second class hardwood plain fillets (sectional area exceeding 13 sq.cm and not exceeding 25 sq.cm), square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and directed.

All as per Sl No. 9 here-in-before, but except fillets complete all as specified and directed. Note: Serviceable wooden fillets obtained from item No. 8.00 here-in-before will be reused under this item.

Dismantling timber scantlings 40 sq. cm and over in section, unframed work, in any position complete all as specified and directed.

M&L for second class hardwood in scantlings, clean sawn, fixed complete all as specified and directed.

All as per Sl No. 12 here-in-before, but except scantlings complete all as specified and directed. Note: Serviceable wooden scantling obtained from item No. 11.00 here-in-before will be reused under this item.

Dismantling old false ceiling work including wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness complete all as specified and as directed.

M&L for 4 mm thickness non-asbestos fibre cement building boards (decorative type) fixed or laid/ inserted to timber/ GI/ Aluminium framework with screws complete all as specified and directed.

S&F anodised aluminium snap grid frame work (size of grid 605x605 mm) with 35x25x1.5 mm main tee and 25x25x1.4 mm cross tee and wall angle for false ceiling complete all as specified and directed.

S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F rolled mild steel structural work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self-tapping screws/ J-hooks complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self-tapping screws/ J-hooks complete all as specified and directed.

Demolition of brick work/ PCC block/ stone wall masonry built in cement mortar and removing the debris/ rubbish to a distance not exceeding 100 mtr complete all as specified and directed.

M&L for pre-cast cement concrete block masonry type C1, 1:3:6 using 20mm graded stone aggregate with solid blocks exceeding 10 cm in width and setting in CM 1:4 complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for 40 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded stone aggregate over RCC roof as levelling course complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster on fair faces of brick work/ concrete surfaces in cement mortar 1:3, mixed with water proofing compound @ 3% by the weight of cement, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for APP modified water proofing membrane thickness not less than 4 mm and weighing not less than 4.50 Kg/ Sqm, reinforced with non-woven polyester, matt black finished (not less than 150 gms/ sqm) having softening point not less than 140 degree Celsius, longitudinal tensile strength not less than 300 N/ Sqcm, tearing strength of 100 Nm by laying torch application including minimum 10 cm side lap and 15 cm end laps over a coat of bituminous emulsion @ 100 gms/ Sqm on surface and hot blown bitumen 85/ 25 grade @ 1.20 Kg/ Sqm and finishing with solar reflective bituminous aluminium paint applied 100 gms /sqm complete all as specified by Engr-in-charge.

Preparation of the concrete surface by mechanical means (mechanical grinding) to ensure a good bond between the coating and the substrate. Supplying and applying High Build Elastomeric waterproofing membrane based on pitch free polyurethane, cold applied of spray / brush applied single component membrane which is root resistant with minimum elongation of 400% as per ASTM D 412 and the system includes final base preparation, applying Nitoproof 600 PF/Equivalent in two coats with solid content not less than 85% applied at 2 kgs / sqm. The required thickness of 1.2mm DFT and the mixing, composition, proposition etc shall be as per manufacturer specifications and approved by consultants. Porous concrete surfaces to be primed with Nitoproof WB primer. The cracks / construction joints / honey combs / leaking spots in the slab shall be provided with pressure grouting using cementitious system by admixing Cebex 100 - 225 grams to 50 kg bag of cement. The junctions shall be chamfered using Nitobond SBR admixed polymer mortar prior to application of waterproof coating. Termination to be done above the FFL to a height of 300mm after taking U groove of 10mm wide x 10mm thick flushed with polymer modified mortar as per vendor recommendation. The exposed portion of waterproof coating shall be applied with aliphatic polyurethane coating using Dekguard PU/Equivalent @ minimum 100 microns dry film thickness in two coats over the Polyuria waterproofing including temporary lifting of Water tanks, Pipe line, cable trays etc must be done to enable application of waterproofing membrane and any civil related repair of structures like upstands, etc, shall be done prior to application of Waterproofing system. The material shall comply to – ASTM C 836. Elongation (ASTM D412): >400 %, Specific gravity: 1.4 g/cc, Solid content: 85%, Modulus @ 100% elongation (ASTM D412): 0.62 N/mm², Tear resistance (ASTM D624) : 15 N, Water vapour transmission(ASTM E96) : 0.6 g/m²/hr., Water permeability @ 5 bar : Nil, Shore A hardness (ASTM D2240) : 60

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M&L for rendering in two layers as 5 mm thick with cement mortar (1:4) mixed with water proofing compound @ 3% by the weight of cement over rendering 10mm thick with cement mortar (1:6) on fair faces of brick work in external surfaces of wall complete all as specified and directed. Note: Water proofing compound will be measured and paid separately.

M&L for 5mm thick rendering in cement mortar 1:3 on fair faces of concrete surfaces as in ceiling finished even and smooth without using extra cement etc complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster on fair faces of brick work/concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

Supply only Liquid water proofing compound complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M&L for preparation of newly plastered ceiling surfaces and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

Cutting/ cleaning small trees, saplings, shrubs and under growth complete roots from brick walls, chajjas etc including taking out complete roots from inside walls/ chajjas and making good surfaces in cement concrete 1:2:4 type B1 or in cement mortar (1:4) to match the existing surfaces complete all as specified and directed.

Disconnecting existing tank capacity 500 Ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position after cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes etc complete all as specified and directed.

M&L for arresting leakage in the RCC/ sheet/ tiled roof with approved sealant or cement and making the surface good and clean including making necessary scaffolding arrangement up to height four storey as per the site requirement/ condition complete all as specified and directed.

M&L for clearing vegetation/ shrubs along with all the debris of leaf from roofs, sunshades, etc and making surface clean, making good with plaster in CM 1:3 or PCC 1:2:4 (12.5 mm graded aggregate) as per the site requirement/ condition complete all as specified and directed.

S&F rolled mild steel structural work sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410-W(Gde-E- 250) quality-A complete all as specified and directed.

S&F rolled mild steel structural work plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe 410-W(Gde-E- 250) quality-A complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide Zinc Chrome primer complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in bed blocks for fixing hold fasts, coping, haunching, filling in pressed steel chowkats or similar work including necessary form work as required complete all as specified and directed.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

M&L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B1, using 20mm graded stone aggregate as in manhole / Gully trap cover slab set in CM 1:4 including use and waste of necessary form work complete all as specified and directed.

S&F TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L for washing, rubbing down and stopping of old distempered surface on walls and applying one coat of distemper oil emulsion on walls complete all as specified and directed

M&L for complete removal of existing treatment and applying 3 mm thickness wall care putty over plastered surface to prepare the surface even and smooth, applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

M&L for preparation of old surface of walls and applying one coat of Exterior Emulsion paint (Water proofing Paint) all as per manufactures instructions and specified.

M&L for complete removal of existing treatment applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade Company Depot Tinted) with silicon additives 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old wood or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster on stone masonry surfaces or surface other than fair face of brick-work in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of wall and applying a layer plaster of Paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth, applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed.

Supply only integral water proofing compound all as specified and as directed.

M&L for preparing new plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for writing letters or figures (Block. Roman, Italic or Indian) not exceeding 30 cm high including repainting on back ground in black colour complete all as specified and directed.

M&L for writing stops, commas, short lines, dashes, hyphens, brackets, etc. including cleaning the existing surface complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) complete all as specified and directed.

M&L for non-skid ceramic tiles (coloured) 7 to 8mm thick, (Square/rectangular), area of each tile exceeding. 0.18 Sqm but not exceeding 0.38 Sqm as in skirtings, dados set and joint in cement slurry, jointed & pointed in white or coloured cement to match the surface of the tile over and including 10 mm thick screed bed in cement mortar 1:3 complete all as specified and as directed.

M&L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 350x 250x 7mm/ 450x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:3) complete all as specified and directed.

M&L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) complete all as specified and directed.

M&L for non-skid ceramic tiles (coloured) 7 to 8mm thick, (Square/rectangular), area of each tile exceeding. 0.11 Sqm but not exceeding 0.18 Sqm as in skirtings, dados set and joint in cement slurry, jointed & pointed in white or coloured cement to match the surface of the tile over and including 10 mm thick screed bed in cement mortar 1:3 complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like over 20 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed

Demolition of cement Concrete (unreinforced) in ground floors and paving's not exceeding 15 cm thickness (below or above ground level) and remove rubbish off the premises complete all as specified and as directed.

M&L for Hardcore using broken bricks of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, Type C2 (using 40mm graded stone aggregate) as in plinth protection/ path laid to slope 1 in 12 and finishing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering of exposed edges complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in surface channels, drains including all necessary form work complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

Taking down chowkats or frame exceeding 1.50 and not exceeding 4 sqm each with shutter (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frame not exceeding 1.50 sqm each with shutter (without taking off shutters from the frame) complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F mild steel flat iron holdfasts for chowkats and similar articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for second class hardwood plain, framed, panelled shutters 30 mm thickness (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

M&L for second class hardwood glazed and skeleton shutters, 30 mm thick open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and metered beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F in repairs aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F in repairs 4-lever, mild steel, Mortice lock, vertical type, size 100 mm complete all as specified and directed.

S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, (overall length of cover plate 150mm) fixed in floor complete all as specified and directed.

M&L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty including taking down old floor spring complete all as specified and directed.

M&L for 12 mm thick Prelaminated particle board, exterior grade, Prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber/ aluminium frame work including taking down old particle board complete all as specified and directed.

S&F 4.80mm thick sheet glass, ordinary quality and glazing with oil putty or fixed with beads in squares exceeding 0.50 Sqm in each pane including hacking out old broken glass complete all as specified and directed.

M&L for preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and directed.

S&F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 75 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F in repairs 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F in repairs 150 mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F in repairs 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F 150mm size aluminium handles, cast type, anodised, all as specified and directed.

S&F in repairs 150mm size aluminium handles, cast type, anodised, all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm dia and fixed with steel staple or wooden bead complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm dia and fixed with steel staple or wooden bead complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty or fixed with beads in squares not exceeding 0.50 Sqm in each pane including hacking out old broken glass complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty or fixed with beads in squares exceeding 0.50 Sqm in each pane including hacking out old broken glass complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty or fixed with beads in squares not exceeding 0.50 Sqm in each pane including hacking out old broken glass complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty or fixed with beads in squares exceeding 0.50 Sqm in each pane including hacking out old broken glass complete all as specified and directed.

S&F 15 mm bore Unplasticised PVC pipes ASTM 1784 Sch 80 class III and fittings fixed complete to walls, ceilings or in floors etc., any type of pipe including taking down old pipe complete all as specified and directed.

S&F 20 mm bore Unplasticised PVC pipes ASTM 1784 Sch 80 class III and fittings fixed complete to walls, ceilings or in floors etc., any type of pipe including taking down old pipe complete all as specified and directed.

S&F 25 mm bore Unplasticised PVC pipes ASTM 1784 Sch 80 class III and fittings fixed complete to walls, ceilings or in floors etc., any type of pipe including taking down old pipe complete all as specified and directed.

Supplying and laying 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down old pipe complete all as specified and directed.

S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed suitable for 20 mm bore dia of pipe complete all as specified and directed.

S&F in repairs Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed suitable for 25 mm bore dia of pipe complete all as specified and directed.

S&F 25 mm outer dia. CPVC tank adaptor complete all as specified and directed.

S&F in repairs bib tap 15 mm bore dia standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm- 125gms) complete all as specified and directed.

S&F in repairs bib tap cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for 15mm bore dia iron pipe/ PVC pipe or for brass ferrule complete all as specified and directed.

S&F in repairs pillar taps of size 15mm bore dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts screwed for iron pipe complete all as specified and directed.

S&F in repairs pillar taps of size 15mm bore dia, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts screwed for iron pipe complete all as specified and directed.

S&F in repairs stop valve/ angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for unions or fixed for 15mm bore dia of pipe complete all as specified and directed.

Fixing only in repairs 32/ 40mm dia PVC waste pipe 80 cm long with union for WHB complete all as specified and directed. Note : Item will be issued under Schedule B Store.

Fixing only in repairs 32 mm dia waste fittings, brass, chromium plated for glazed ware sinks, wash basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. Note : Item will be issued under Schedule B Store.

S&F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand, waste pipe and connected fittings complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including fixing bolt, seat cover (excluding flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage etc complete all as specified and directed.

S&F in repairs vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repairs 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and including 32 mm bore PVC flush pipe complete all as specified and directed.

S&F in repair plastic water closet seat cover any colour closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified and directed.

S&F in repairs PVC connections 15mm size, 450mm length with 02 Nos brass check nuts with washer etc complete all as specified and directed.

Fixing only in repairs PVC connections 15mm size, 450/ 600/ 750/ 900mm length with 02 Nos brass check nuts with washer etc complete all as specified and directed. Note : Item will be issued under Schedule B Store.

S&F chromium plated connection pipe 450 mm long braided hose with two 15 mm nuts and rubber washers (suitable for geysers, basin mixers) complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, outlet 75 mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs PVC (SWR) multi floor trap, outlet 75 mm dia, with grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs Harrison rails/ curtain rod/ drapery rod 20mm dia, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed.

Fixing only in repairs Harrison rails/ curtain rod/ drapery rod 20mm dia, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed. Note : Item will be issued under Schedule B Store.

S&F in repairs chromium plated brass shower roses 125 mm size with or without swivel joints including fixing to steel/ PVC pipe or union complete all as specified and directed.

S&F in repair worn out wooden pelmet boxes or cupboard shutter of 18/19 mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work 2nd class hardwood plugs 30x30x40mm embedded in wall with cement mortar (1:3) including taking down existing unserviceable boarding of any description complete all as specified and directed.

Fixing only in repair aluminium handle 100mm size, cast type anodised fixed with screw complete all as specified. Note : Item will be issued under Schedule B Store.

Fixing only in repair aluminium handle 150mm size, cast type anodised fixed with screw complete all as specified. Note : Item will be issued under Schedule B Store.

S&F in repairs corner glass assembly fancy type with stainless steel frame (200mmx200 mm) chromium plated screwed down for fixing to walls with screws complete all as specified and directed.

S&F in repairs fancy type plastic cabinet of size 450x300x100mm approved colour fixing to walls complete all as specified and directed.

Fixing only in repairs fancy type plastic cabinet of size 450x300x100mm approved colour fixing to walls complete all as specified and directed. Note : Item will be issued under Schedule B Store.

S&F in repair towel rail 20 mm dia, D type 60 cm long of brass chromium plated complete all as specified and directed.

Fixing only in repair towel rail 20 mm dia, D type 45cm/ 60 cm long of brass chromium plated complete all as specified and directed. Note : Item will be issued under Schedule B Store.

Fixing only in repair for Aluminium alloy anodised, sliding door bolt 300/250 mm long with haps staples (bolt type) and fixing clip of sheet , cast or extruded section and fixing bolt and sliding bolt of extruded sections or cast aluminium alloy complete all as directed. Note : Item will be issued under Schedule B Store.

Fixing only in repair for door closer hydraulically regulated designation No 3 universal type aluminium extruded section body, suitable for door shutters of 851 to 1000 mm width and weight between 61 to 80 Kg and fixed complete all as specified and directed. Note : Item will be issued under Schedule B Store.

Fixing only in repair 200mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. Note : Item will be issued under Schedule B Store.

Fixing only in repair 150mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. Note : Item will be issued under Schedule B Store.

Fixing only in repair 100mm long butt hinges, medium weight, cold rolled mild steel all as specified and directed. Note : Item will be issued under Schedule B Store.

Taking down wooden shutters of any description not exceeding 1 sq.m each and refixing in same opening after carry out necessary repair work including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed.

Taking down wooden shutters of any description exceeding 1 sq.m and not exceeding 2 sq.m each and refixing in same opening after carry out necessary repair work including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed.

Taking down wooden shutters of any description exceeding 2 sq.m each and refixing in same opening after carry out necessary repair work including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed.

Fixing only in repair 75mm long butt hinges, medium weight, cold rolled mild steel all as specified and directed. Note : Item will be issued under Schedule B Store.

Taking down existing aluminium door and window frame with shutters exceeding 1.50 sq.m and not exceeding 4.00 sq.m each for necessary repair work including (replacement of snap beading, screws, stays, rubber neoprene packing, aluminium handles, etc) and refixing in same opening including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed.

S&F 160mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors or fixed to walls including Taking down cast iron pipes/ PVC pipe including fittings by burning out lead joints etc to facilitate dismantling old serviceable fittings/pipe laid in trenches floors or fixed to walls all as directed including earth work. Demolition of PCC/Brick work and making good to match with existing surfaces (upto four storey building) including necessary scaffolding complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors or fixed to walls including Taking down cast iron pipes/ PVC pipe including fittings by burning out lead joints etc to facilitate dismantling old serviceable fittings/pipe laid in trenches floors or fixed to walls all as directed including earth work. Demolition of PCC/Brick work and making good to match with existing surfaces (upto four storey building) including necessary scaffolding complete all as specified and directed.

PINKATRON SECURITIES PRIVATE LIMITED (BID ID -3466542)

Satheesh Kumar (BID ID -3460186)

B.LAMBODHARAN (BID ID -3460933)

SHILPA ENGINEERS AND CONTRACTORS (BID ID -3462024)