PROVISION OF STORAGE WATER TANK AT ICGS OKHA, PROVISION OF RELIGIOUS BLDG AT ICGS OKHA AND PROVN OF STORAGE AND FACILITY ROOM HOVERPORT OKHA UNDER GE (I) CG PORBANDAR

Amount

SCHEDULE 'A'

Surface excavation n. exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.complete all as directed.

Excavation over areas n.exc 1.50 Mtr deep and getting out in soft/loose soil

All as per item no 02 exc 1.50m but n.exc 3.00 mtr

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out soft / loose soil all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm hard/dense soil all as specified.

Excavation in post hole each n.exc 0.50 Cum getting out, returrning filling in and ramming earth or broken ruble mixed with earth around, in layer n.exc 25 cm, watering and removing surplus soil to a distance n.exc 50m and making good surfaces in soft/loose soil all as specified

Spreading & levelling in layers n.exc. 25 CM thick well ramming including watering as required.

M&L Sand Filling Under Floors or in foundation including watering and consolidation

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

M&L Broken bricks loose filling with aggregate of gauge 40 to 80 mm in filling of soakage well

M&L Hardcore of guage n.exc. 63mm, deposited spread & levelled in layers n.exc.15CM thick, waterd & rolled/ rammed to a true surface using broken stone or boulders 50 MM thick.

M&L Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area all as specified and as directed.

M&L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured all as specified and as directed.

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface all as specified and as directed.

M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area all as specified and as directed.

M&L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall all as specified and as directed.

M&L Plain cement concrete, type D2, 1:4:8 (using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc all as specified and as directed.

M&L Plain cement concrete, type B2, 1:2:4 (using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc all as specified and as directed.

M&L Plain cement concrete type C-1 (1:3:6, 20 mm graded stone aggregate) as in copings, packing around chequered tiles, interlocking paver.

M&L Plain cement concrete type B-1 ( 1:2:4) using 20 mm graded stone aggregate as in window and door cills, lintels, bressumers, steps, quoins, manhole cover slabs, of any thickness, with plain fair faces including chambering weathering, throatings etc including necessary form work, setting in cement mortar (1:4) complete all as specified and directed.

M&L RCC (Design mix)M-30 using 20mm graded stone aggregates as in foundation including raft footing foundation beam plinth beam bases for columns etc basement slab under reamed piles and mass concrete

M&L RCC (Disign mix) M-30(20mmgraded aggregate) in Walls, retaining walls,basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses

M&L RCC (Disign mix)M-30 using 20mm graded stone aggregates as in slabs supported onwalls, beams and colums in floors, roofs, landings, balconies, canopies ,deck slabs and in shelves and the like complete all as specified and directed by Engr-in-charge

M&L RCC (Disign mix)M-30 using 20mm graded stone aggregates as in Chajjas

M&L RCC (Disign mix)M-30 using 20mm graded stone aggregates as in beams,cantilevers, bressumers and lintels over 1.5 mtr span complete all as specified and directed by Engr-in-charge.

M&L RCC (Disign mix) M-30 using 20mm graded stone aggregates as in Columns,pillars,piers, posts and struts

Supply only water proofing compound

M&L DPC in Plain cement concrete (1:2:4) type B-0 to horizontal or vertical surfaces including necessary formwork 40mm thick.

M&L Precast cement concrete block masonary, type C1 (1:3:6) using 20mm graded stone aggregates with solid blocks, exc 10cm in width and setting in cement mortar 1:6, complete all as specified and directed.

M&L Marble work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types (a) Makrana white all as specified and directed.

Formwork to sides of concrete foundations, footings,bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work;vertical or to batter,curved, as in rough finished surfaces of concrete complete all as specified and directed.

Formwork to faces of walls,retaining walls, abutments,parapets and staircase railings and similar work including attached pillasters, buttresses,etc.; vertical or to batter for fair finished surfaces.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick for fair finished surface (Horizontal or sloping) etc complete all as specified and directed by Engr-in-charge.

Formwork to chullah hoods, chajjas, troughs and similar items including edges as in fair finished surfaces of concrete etc complete all as specified and directed by Engr-in-charge.

Formwork to sides and soffits of roof beams,haunchings, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs also splays between floor and beam and the like for fair finished surfaces of concrete etc complete all as specified and directed by Engr-in-charge.

Form Work To Sides of pillars, posts, struts, piers, columns (square, rectangular or polygonal) as in fair finished surfaces of concrete complete all as specified and directed.

Form work to edges of concrete flats,treads,break in floor, window cills, concrete railings, opening in concrete walls and sides of RCC / Plain cement concrete bands in walls, horizontal or sloping and all similar work all exceeding 5cm but not exceeding. 10cm wide for a fair finished surface complete all as specified and directed.

M&L 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S & F 35mm thick glazed skeleton shutters open rebated and prepared to receive glass guage etc without sash bars edges of framing plain chamfered or rounded, fitted with cut and mitered beads with size of beading 15 x 10mm, for securing glass etc size of members of shutters complete all as specified and directed.

S & F 40 mm thick 2nd class hard wood, Plain framed,factory made panelled shutter (two panels) with lock rail and panel of 9mm BWR comercial ply or 12mm vennered particle board with comercial veneering on both faces,The size of rail and stile as per IS:1003 (Part 1), klin seasoned & chemically pressure treated complete all as specified and directed.

S & F Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like inclding all necessary labours, articles n.exc. 200 Cu Cm each complete all as specified and directed.

S & F 30 mm thick factory made solid panel PVC door shutter conferming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming stiles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-inCharge Make : RAJSHREE/SINTEX

S & F Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with 19x 19mm MS square tubes, provided with EPDM rubber gasket throughout the frame fixed in opening complete as per manufacturer's specifications and as directed by Engineer-in-Charge Make: RAJSHRI/SINTEX)

S&F 150mm long Aluminium anodized barrel tower bolts of extruded section of bolt (ISI Marked) complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised,sliding door bolt with hasp,staple (ISI Marked) (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 100 mm long extruded aluminium alloy anodised Butt hinges (ISI Marked) complete all as specified and directed.

S&F 125mm long Extruded aluminium alloy handles, fabricated type,anodised (ISI Marked) complete all as specified and directed.

S&F 20mm dia Aluminium alloy curtain rods, chromium plated with fixing rings and brackets, stops and rollers all as specified and directed.

S&F Aluminium anodised door closer hydraulically regulated, exposed, tubular type (Type B) designation No.3 universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

S&F Aluminium alloy wire cloth,0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples

S&F MS work as in Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge

S&F MS work Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engineer-in-Charge

S&F Mild Steel Screw bolts (Machine made) of 16 to 20 mm dia with Hexagonal or square Heads At one end and screwed the other or screwed both ends each screwed end to be fitted with washer and one hexagonal or square nut not exceeding 5cm long complete all as specified and directed by Engr-in-Charge

M&L Mild steel CRS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. etc complete all as specified and directed by Engr-in-charge.

M&L Mild steel CRS TMT bars 8 mm dia Round Bars cut to length bent to shape required including cranking bending spirally for hooping for colums hooking ends and bending with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed by Engr-in-charge.

All as per above item No.50.00 but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders etc complete all as specified and directed by Engr-in-charge.

Fixing only chain Link Fencing Including Line wire any Mesh Size and type to any type of standared rails straining bolts etc including provision of binding wire Complete all As Specified and directed by eng-in-Charge

S&F Powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

Supply only Chain Link MS Galvanised any Size or type Complete all As Specified and directed by eng-in-Charge

M&L Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2kg/m2 incl cleaning surface all as specified and directed

M&L APP Based Polymeric memberane minimum weighing 3 kg /sqm and minimum 3mm thick Reinforced with polyster non wove fabric (wt not less than 150 gms/ sqm) land on primed surface by forced application complete all as specified and Directed by Eng-in- Charge

M&L 50 mm thick, Plain cement concrete, type C2, (1:3:6 using 40mm graded stone aggregate) as in plinth protection finished fair and even without using extra cement. complete all as specified and as directed by Engr-in-Charge.

M&L 75 mm thick, Plain cement concrete, type C2, (1:3:6 using 40mm graded stone aggregate) as in floor finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L 75mm thick, Plain Cement concrete, type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base of floors even and rough finished to receive topping layer complete all as specified and as directed by Engr-in-Charge.

M&L Non - skid coloured ceramic tiles 7 to 8 mm thick, joint free (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over screed bed of 15 mm thick 1:6 and pointed in coloured cement to match complete all as specified and as directed by Engr-in-Charge.

M&L Double charged Vitrified tiles 9 to 10 mm thick light shade (square/ rectangular) polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and white or coloured cement to match over screed bed of 15 mm thick 1:6 and pointed in white or coloured cement to match as in floor etc , all as specified and directed by Engr-in-charge.

M&L Double charged Vitrified tiles 9 to 10 mm thick light shade (square/ rectangular) polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, in vertical surfaces etc. set and jointed in neat cement slurry and white or coloured cement to match over screed bed of 15 mm thick 1:4 and pointed in white or coloured cement to match as in floor etc , all as specified and directed by Engr-in-charge.

M&L Glazed coloured ceramic tiles in verticle surfaces 300x 450x 6-7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match over backing bedding layer 10mm thick 1:4 and pointed in white or coloured cement to match etc complete all as specified and directed by Engr-in-charge.

M&L Machine cut Kota stone slab flooring 20 to 25 mm thick over cement screed base 1:4, 15mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L Machine cut Kota stone slab flooring 20 to 25 mm thick, but fixed in risers of steps, skirting, dado and pillar laid over cement screed base 1:3, 10mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L 60mm thick M-35 Grade Machine pressed precast cement concrete interlocking paver block any shape and size confirming to IS 15658-2006 with grey cement and pigment compllete all as specified

M&L Chequered cement concrete tiles 30cm x 30cm x 25mm thick, machine pressed,set, jointed and pointed in neat cement slurry in floors over 15mm thick screed bedding layer in CM 1:6 all as specified and directed.

M&L 15mm thick rendering in CM 1:4 on fair faces of concrete or stone masonary finished even and smooth without using extra cement complete all as specified and as directed.

M&L 15mm thick rendering in CM 1:6 on fair faces of concrete or stone masonary finished even and smooth without using extra cement complete all as specified and as directed.

M&L 15mm thick rendering in CM 1:3 on concrete surfaces of ceilings finished even and smooth without using extra cement complete all as specified and as directed.

M&L 15mm thick rendering in CM(1:3) on concrete surfaces work finished even & smooth without using extra cement.

M&L applying 3mm thick white cement based wall care putty on walls

M&L Preparation of new plastered surfaces of walls and applying two coat of Oil emulsion Distemper over a coat of alkali resistant primer on new surfaces of wall complete all as specified.

M&L Preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified.

M&L Preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified.

M&L Preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete all as specified.

S&F 4 mm thick, flat, transparent, sheet glass ordinary quality and glazing with linseed oil putty in square exc 0.50 Sq.m in each pane complete all as specified and as directed.

S&F Polyester solar control film 50 micron reflective type (gareware sun control or equivalent)

M&L Preparation of new wooden surfaces of any description exc 10cm width or girth & aplying two coats of synthtic enamel paint (ordinary tint), glossy finish over one coat of pink primer all as specified.

M&LPreparation of new steel surfaces of any description exc 10cm width or girth & aplying two coats of synthtic enamel paint` over a coat of red oxide primer all as specified.

S &F 16mm dia, 3-layer, PP-R (Poly propylene random copolymer) pipes SDR-7, UV stabilised and antimicrobial fusion having thermal stability for hot and cold water supply including all PP-R plain and brass threaded poly propylene random fittings (such as elbow, tee, reducers, couplers, short pieces, connections, union etc,.) whatever required as per manufacturer instruction fixed on walls/ceilings complete all as specified and directed

S &F 20mm dia, 3-layer, PP-R (Poly propylene random copolymer) pipes SDR-7, UV stabilised and antimicrobial fusion having thermal stability for hot and cold water supply including all PP-R plain and brass threaded poly propylene random fittings (such as elbow, tee, reducers, couplers, short pieces, connections, union etc,.) whatever required as per manufacturer instruction fixed on walls/ceilings complete all as specified and directed

S &F 25mm dia, 3-layer, PP-R (Poly propylene random copolymer) pipes SDR-7, UV stabilised and antimicrobial fusion having thermal stability for hot and cold water supply including all PP-R plain and brass threaded poly propylene random fittings (such as elbow, tee, reducers, couplers, short pieces, connections, union etc,.) whatever required as per manufacturer instruction fixed on walls/ceilings complete all as specified and directed

S&F PP-R gate valves as per requirement of the site 25mm bore of pipes complete all as specified and directed.

S&F 500 Litre three layered capacity rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed in position all as specified and directed including provision of 200mm long 50mm bore GI nipples for inlet, outlet, overflow, drain out pipe including provision of check nuts.

S & F Bib taps 15 mm bore cast copper alloy, fancy type, Chromium Plated with capstan head screwed for iron pipe or brass ferrule all as directed by Engineer-in-Charge

S&F Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed 15 mm dia all as specified and directed by Engineer in Charge.

S & F 15mm Bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S & F 15mm Bore concealed stop valves, cast copper alloy, Chromium plated with long shank and cup, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S & F 20 mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S & F 20 mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Min weight 150gms)

S&F 450mm long Towel rails of PTMT fixed with and including CP brass screw screws and wooden cleats minimum weight 170 gms

S & F PVC connection 15 mm size with PTMT nuts of length 450 mm of approved quality

S&F Stack clamps for 100mm dia pipe made out of 50mm x 5mm, MS flat iron & 16mm dia round iron stays, incl nuts & bolts & securing ends of stays to wall & roof.

S & F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches, in floors, fixed to walls all as specified.

S & F 110mm dia PVC (SWR) bend of any radius complete all as specified and directed.

S&F 110mm dia PVC (SWR) vent cowl

S&F 32mm dia, Brass chromium Plated Bottle Traps for wash basins with inlet and outlet screwed for pipe or connection including necessary packing union, cap and fixed complete all as specified and directed

M&L for 100 mm dia cast iron floor trap with grating, jointed to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed

M&L concreting bed to drain pipe of 150mm bore pipe including packing under and haunching against the sides of pipes after they are laid and tested in Plain cement concrete 1:4:8 type D2 complete all as specified and directed.

M&L 150mm bore Salt glazed stone ware drain pipes, Grade A, laid and jointed all as specified

M&L Salt Glazed Stone Ware gully trap 150 x 150mm size , square or round mouthed,type-P complete all as specified and directed.

Cutting into existing manhole/Septic Tank for connecting new drain pipe of 150mm dia and making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4) section in cement concrete 1:2:4 type B1,smooth finished and reforming benching , all as required.

S&F Soap Dish Stainless steel chromium plated decorative type approximate size 160x160x90mm complete all as specified and directed.

Demolition and breaking up existing 100mm dia drain pipe (salt glazed ware, AC or reinforced concrete pipe) set in cement mortar and S & F 150mm dia PVC (SWR) pipe, grade ‘A’, single socketed in any length, jointing with cement solvent solution, laid in trenches complete all as specified and directed.

S & F 10 litre capacity, PVC low level cistern,syphonic action type, white, with unlet ball valve, float and handle including brackets complete of approved.

S & F vitreous china wash hand basin, white, flat back, of size 450 x 300 mm including waste chain and plug or porcelain stopper but including cutting for and pinning in ends of brackets all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern) white with integral P or S trap of inlet depth 75mm including connection to drain (or out going pipe and to flushing pipe,antisyphonage pipeincluding flush pipe &jet pressure etc

M&L Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed copper conductor FRLS 1100 Volts grade cable, drawn through and including PVC concealed conduit heavy duty grade ISI marked 20 mm dia (external), including conduit accessories like bends, tees, junction boxes etc fixedconcealed/recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire including metal flush modular switch box with frame and cover plate for modular switches, sockets etc all as specified and directed by Engineer in Charge (a) One light point controlled by one switch.

(b) One fan/Exhaust fan point controlled by one switch/regulator

( c) One 3 pin socket outlet, 6 amps,on same board

( d) One 3 pin socket outlet, 6 amps, independent,board.

M&L Point wiring complete with 4 sqmm single core PVC insulated but usheathed copper conductor FRLS 1100 Volts grade cable, drawn through and including PVC concealed conduit heavy duty grade ISI marked 20 mm dia (external), ISI Marked, including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling etc including 4 sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire for One 3 pin socket outlet. 15 amps, independent board including metal flush modular switch box with frame and cover plate for modular switches, sockets etc all as specified and directed by Engineer in Charge

M&L Point wiring complete with 2.5 sqmm single core PVC insulated but usheathed copper conductor FRLS 1100 Volts grade cable, drawn through and including PVC concealed conduit heavy duty grade ISI marked 20 mm dia (external), ISI Marked, including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling etc including 2.5 sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire for One 3 pin socket outlet. 15 amps,independent board including metal flush modular switch box with Hylem sheet 3.0mm thick for fixing of switches, sockets etc all as specified and directed by Engineer in Charge

S&F Modular Switch 1 way, 6 Amps, 1 modular complete all as specified and directed. Make: Crab Tree (Athena), Havells (Oro), Anchor (vision)

S&F Modular Switch 1 way, 16 Amps, 1 modular complete all as specified and directed. Make: Crab Tree (Athena), Havells (Oro), Anchor (vision)

S&F Modular Socket , 6 Amps, 2/3 pin combined 2 modular complete all as specified and directed. Make: Crab Tree (Athena), Havells (Oro), Anchor (vision)

S&F Modular Socket , 6/16 Amps, 2/3 pin combined 2 modular complete all as specified and directed. Make: Crab Tree (Athena), Havells (Oro), Anchor (vision)

S&F Modular Fan regulator,120 watt, 2 modular complete all as specified and directed. Make: Crab Tree (Athena), Havells (Oro), Anchor (vision)

S&F Switch Socket combination 5A/16A, 5 in 1 all as specified and directed.

S&F Switch piano, flush button,230V, 5 Amps, Single pole one way (ISI Marked) complete all as specified and directed by Engineer-in-Charge.

S&F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type all as specified and directed.

Material and Labour for ceiling rose, surface type, 3 way terminal/PVC/ Polycarbonate isolated body complete all as specified and directed by Engineer-in-Charge.

M&L 250 mm bore for earthing complete with galvanised steel pipe electrode, 40 mm bore, medium grade, 3.0 metres length, not less than 2.75 metres below ground level connected with earthing lead of 16 sqmm Aluminium conductor drawn in to and including PVC conduit medium grade, filling of bore with chrcol dust and salt and earth enhance gel, and connected to the earthing test point all as specified and directed. Note: 1. cost of earth wire and PVC conduit for protection of earth conductor deemed to be included in unit rate up to 7.5 meter 2. Result should be less than 2 Ohms

S&F MCB DB sheet enclosure, 4 way, VTPN, Double door, IP 43 with standard bus bar of suitable size and common neutral link , din bar all enclosed in 1.6 mm thick CRCA sheet steel flush mounting type complete with following (a) MCB 63 Amp 10KA Four Pole 'C' series-----01 Nos. (b) MCB SP 20 Amp 10KA.'C' series....04 Nos. (c) MCB SP 6/10 Amps 10KA.'C' series 06 nos Make: Hager/ L&T/ Legrand./Siemens, complete all as specified and directed by Engr-in-Charge.

S&F 18/20W recessed mounted LEDdownlight housing made of extruded aluminium with diffuser and integrated electronic driver with high efficiency long life LED chips, PF> 90, system luminious efficiency >80, CCT 5700K, Operational Voltage 140V-270V, 50/60 Hz including electrical connection with 3 core flexible conductor cable of appropriate size complete all as specified and as directed by Engr-in-Charge. Make:cat no: Wipro CRDL11RO23HP57/ or Equivalent from Philips / Bajaj

Supply & fix fans celing complete with electronic type regulator and accessories 220-240Hz, 50Hz, 1200mm sweep, Nominal Air delivery 215 CMM, BEE 5 star rated complete all as specified and directed. Make: Almonard/Havells/Khaitan

S&F 9W surface/wall mounted round shape LED downlight with minimum efficiency 90 lumen/W, HET PC opal copncave diffuser, high quality CRCA reflector, input voltage 220-240V,CCT 6000K, input frequency 50-60Hz including electric connection with 3 core flexible Cu conductor cable of appropriate size from ciling rose to fixture complete all as specified and directed. Make:cat no: Wipro LW01-101-xxx-60xx/ GE Cat No 93057384/ Bajaj cat No BGCML12WWH

S&F 20W surface/Wall mounted Batten LED Luminaire, etruded aluminium housing with PC diffuser and integrated electronic driver with high efficiency long life LED chips, CRI=80(Minimum) PF>0.95, System luminous efficiency >100, Operating voltage 140V-240Vincluding electrical connection with 3 Core flexible cable of appropriate size from ceiling rose to LED fitting complete all as spd. Make: Bajaj Cat No BLTRU 20W WHVIVA / OSRAM Cat no Lux Power Batten 19WL840

M&L Anodised sliding type window with frame size 60X40X2.00 mm thick and shutter with section bearing bottom 52x18X1.50, top 39.4 x17.7 x1.5mm and sides 39.4 x 17.7 x 1.5mm (suitable for moving over two track fixed over top of frame work, top and side section of size 61.6x31.75x1.5mm and bearing bottom track of size 61.6x31.75x1.5mm incl necessary aluminium jointing cleats,glazing cleats,rubber packing anodised aluminium snap beading, screws etc with 5mm thick tinted/plain glass in panels incl all fitting & fixture complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium grill with suitable aluminium anodised frame F/H section manufactured by M/s DECO GRILL as per design No DG-104, 6.5 mm thick. complete all as specified and as directed by Engr-in-Charge.

Supply and lay 110 mm OD, Double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 ( Part I and II) for protection of underground cables with all fittings. laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc for cable protection all as specified (excavation and earth work shall be measured and paid separately) Make: Rex/Poly/Gemini

Supply and lay 63 mm OD, Double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 ( Part I and II) for protection of underground cables with all fittings. laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc for cable protection all as specified (excavation and earth work shall be measured and paid separately) Make: Rex/Poly/Gemini

Supply, laying, Jointing and testing XLPE insulated, Extruded PVC outer sheath and inner sheath, galvanised steel armoured cable with aluminium conductor suitable for rated voltage of 1100 Volts grade and laid in trenches/pipe / ducts or on pole complete all as specified and directed of size16 Sq mm 4 core

Supply, laying, Jointing and testing XLPE insulated, Extruded PVC outer sheath and inner sheath, galvanised steel armoured cable with aluminium conductor suitable for rated voltage of 1100 Volts grade and laid in trenches/pipe / ducts or on pole complete all as specified and directed of size 120 Sqmm 3.5 core

M&L Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed copper conductor FRLS 1100 Volts grade cable, drawn through and including non metallic rigid PVC concealed conduit heavy duty grade ISI marked 20 mm dia (external), including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire Iincluding sunken type pressed steel terminal boxes of suitable size with 3mm thick bakelite sheet white/coloured top cover complete all as specified and directed by Engineer in Charge (a) One light point controlled by one switch.

(b)One fan/Exhaust fan point controlled by one switch/regulator

(c)One 3 pin socket outlet, 6 Amps, independent board

SURAJ ENTERPRISE

Nitesh Enterprise