Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹45.4 LAccepted-AOC | L1 | Accepted-AOC L1 BIDDER | |
| 2 | L2₹50.0 L+₹4.6 L (10.1%)Rejected-Finance | L2 | Rejected-Finance 2ND LOWEST BIDDER | |
| 3 | L3₹54.6 L+₹9.2 L (20.4%)Rejected-Finance | L3 | Rejected-Finance 3RD LOWEST BIDDER | |
| 4 | Rejected-Technical 6G SURAH 2ND LANE KOLKATA WB 700010 | KOLKATA | WEST BENGAL | 700010 | - | Rejected-Technical Not- Satisfactory due to shortfall in required Annual Turnover |
Tender Value
₹64.2 L
EMD Value
₹1.3 L
Closing Date
5 Jul 2022, 3:30 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Executive Engineer, DPMU, WB-ADMIP,MSD
Office of the Executive Engineer, DPMU, WB-ADMIP,Agri-Engineering Building (1st floor), Station road, Berhampore, Murshidabad, W.B. - 742101.
All in one Bid for renovation of 01(One) no. of WDS Scheme with allied structures named Chak Gupura- Korgram WDS at Tenya Mouza JL No. 141 under Bharatpur-II block in Murshidabad District under WB-ADMI Project (Phase-X) for the F.Y.2022-2023
2022_WRDD_383853_1
02/P-X/WB-ADMIP/MSD (2nd Call) of 2022-23
Open Tender
CIVIL WORKS
Item Rate
120 days
named Chak Gupura- Korgram WDS at Tenya Mouza
Please refer Tender documents.
3 documents required · 3 mandatory
₹1.3 L
Yes
24 Aug 2022
6 Jun 2022
8 Jul 2022
6 Jun 2022
5 Jul 2022
7 Jun 2022
7 Jun 2022 - 15 Jun 2022
Amount
EARTH WORK AND GRASS TURFING WITH SODS
Excavation in ordinary soil / mixed soil i.e. clay mixed with moorun, kankar, pebbles / silt dry or moist / slushy silt / sticky soil for WDS /WHS/RESERVOIR /SFMIS etc with hydraulic excavator of required bucket capacity including cutting and loading in tippers, trimming bottom and side slopes in accordance with requirement of lines, grades and cross section and transporting to embankment! disposal site within all lifts and lead upto 1000 m including spreading, leveliing disposed spoils at disposed area. (mode of measurement: pre work and post work)& Revised Schedule of Rates vide File No-WRDD-17099/1/2020-CE(WRDD)-WRDD Page-73.
Turfing with Sods Furnishing and laying of the live sods of perennial turfforming grass on embankment slope, verges or other locations shown on the drawing or as directed by theEngineer including preparation of ground, fetching ofsods and watering as per Clause 307 of Specificationsfor Road & Bridge Works of MoRT & H (5th Revision).
Construction of Water Inlet Structure ( 12 Nos.)
Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm.
Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.
Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.
Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation and upto roof of ground floor/upto 4 m (I.) SAIL/ TATA/RINL 8 mm dia c/c @150& binder @ 250 mm
Ordinary cement concrete ( mix 1:2:4 ) with graded stone chips ( 20mm nominal size ) exclusive shuttering and reinforcement if any in ground floor as per relevant I.S codes. a ) Pakur variety.
125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor
Brick work with 1st class bricks in cement mortar (1:4),(a) In foundation and plinth.
Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints , including throating, nosing and drip course, scaffolding/staging where necessary (ground floor) (Excluding cost of chipping over concrete surface) (i) With 1:6 cement mortar (b) 20 mm. thick plaster and Neat cement punning about 1.5 mm. thick in wall, dado, window, sills, floor, drain etc. all complete
CONSTRUCTION OF SINGLE VENT (1200 DIA) H.P. SLUICE GATE WITH DRAW SHUTTER
Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 for Rural Roads of MORD including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.
Bailing out water by pump including all leads and lifts and including making all arrangements for disposal, where continuous flow or seepage of water is encountered and rating of pumps and hours of operation is specifically ascertained as per direction of the Engineer-in-charge.
Filling in foundation or plinth by Silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)
Supplying, dressing and stacking at site bamboo pins above 5 cm. dia. and upto 7.5 cm. diameter. (Dia. to be measured at mid length).
Driving bamboo pins in standing or flowing water including scaffolding and driving appliances. (a) Where boats are not necessary and Taking out old bamboo pins from piling and stacking the same within150 metre from the site of work. (a) Where boats are not necessary.All complete.
Supply of empty cement bags,labour charge for filling will all kinds of earth (wet & dry),sand or aggreegates,damping in position with a led of 30 mtr. & removing after completion,disposing off the same at a distance not less than 150 Mtr. From the site.
Supplying Jhaw / Eucalyptus bullah piles at work site, including dressing and making one end pointed. (iii) 15 cm av. Diameter
Coal tarring with 5% pitch including cost of material and labour complete as per direction of the Engineer-in Charge. (b) Two coats
Labour for driving Jhaw / Eucalyptus bullah piles by monkey in all sorts of soil including hoisting and placing piles in position, protecting the pile head with iron ring and cutting and shaping heads before and after driving and including hire and labour for necessary driving appliances and all tackles. (iii) 15 cm av. Diameter
Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.
Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. (d) With local hard blackstone variety chips (crusher broken)
Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor. (iv) With local hard blackstone variety chips (crusher broken) as per relevant IS codes.
Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(i) Tor steel/Mild Steel. II. other than SAIL/ TATA/RINL
Supplying of Different materials as per approved specification RCC pipe (Ex-outlet) (g) 1200 dia NP-3 spigot.
Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in Single Row Providing and laying reinforced cement concrete pipe NP3 with spigot socket for culverts on first class bedding of granular material in single row including fixing with cement mortar 1:2 as per Technical Specification Clause 1106 for Rural Roads of MORD. (C) 1200 mm dia. ( Add cost and carriage of Pipe to get the final consolidated item rate.)
Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] i) with 1:4 cement sand mortar. b) 20 mm thick plaster and Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m.
Providing weep holes in brick masonary/plain/reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing face. Complete as per drawing and technical specification.
Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)
Hire and labour charges for shoring work (including necessary close plank walling, framing, Eucalyptus/Jhou bulla piling, strutting etc) complete as per direction of the Engineer-in-charge for foundation excavation (vertical surface are in contact with supported earth is to be measured.) (This item should be executed on specific direction of the Enginner in charge) (a) Depth upto 1.5 m.
Brick work with 1st class bricks in cement mortar (1:4) (a) In foundation and plinth
Supplying, fitting, fixing Mild Steel draw shutter with Mild Steel plate of thickness as specified by the Engineer-in-charge and other necessary Mild Steel sections for sluice including fabricating the same (as per drawing and instruction given by the Engineerin- charge) excluding cost of Mild Steel guide channel, sill beam, gearing arrangement etc. but including painting with two coats of anticorrosive bituminous paint of approved make & brand over two coat of red lead primer and with necessary masonry work with all materials supply etc. complete at site.
Supplying, fitting and fixing of Mild Steel Guide Channel with necessary Mild Steel lugs of required length and size by making hole into wall and fixing with necessary masonry work with maintaining proper line and level as directed by the Engineer-incharge. This item includes two coats of anti-corrossive bituminous paint over two coats of red lead primer. Payment will be made on actual length of Guide Channel.
Supplying / Replacing Gear rod by a new Mild Steel Gear rod, threaded length as required and fitting, fixing in position with screw gearing arrangement for operating the draw shutter including taking out old gear rod by cutting bolts etc. complete as per direction of the Engineer-in-charge. (The old materials to be returned to Departmental Godown.) (d) 80 mm dia.
Supplying / Replacing Gun Metal Bush for screw gearing arrangement required for hanging arrangement of draw shutter and fitting & fixing with the screw gearing arrangement for operating the draw shutter by taking out the old screw gearing arrangement and Gun Metal bush etc. complete as per direction of the Engineer-in-charge. (The old materials to be returned to Departmental Godown.) (d) 80 mm. dia.
Supplying, fitting & fixing Cast Iron wheel (after taking out existing one if necessary), rim made of 28 mm. to 36 mm. dia to fit any size of gear rod including carriage to site, painting with two coats of bituminous paint over two coats of red lead primer etc. complete as per direction of the Engineer-in-charge. (a) 45 cm dia. Cast Iron wheel.
Supplying, fitting and fixing top runner fabricated by ISMB / ISMC of required size, 2 nos. for each gate of required length and fitting, fixing with required nos. of anchors / lugs by Mild Steel flat bar of required size bifurcated at one end and welded with the other end with top runner and providing with required drilled holes of required dia. for base plate and all other components as required including carriage of all materials to site complete including painting with two coats of anticorrosive bituminous paint of approved make and brand over two coats of red lead primer etc. all complete as per direction of the Engineer-in-charge.
Supplying, fitting & fixing in position rubber seal arrangements with musical note harmonic 'J' type for making water tight in both up and down stream of draw shutter as well as flap shutter including guide paths, additional M. S. flats, bolts and nuts for fixing the rubber seal in position including fabrication cost and carriage of all materials to site and complete as per direction of the Engineer-incharge. (ii) 127 mm x 6 mm
Miscellaneous
Construction of Display board as per drwaing and placeing of same at suitable location of the command area with best quality black granite with block letter incise as directed by the Engineer in charge.
IKON CONSTRUCTION
TAIMUR SK
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .