REPAIR RECANNING OF CHAIRS REPAIRING OF CHARPOY AND CERTAIN STEEL WOODEN FURNITURE UNDER BSO OF GE ROORKEE

Amount

Charpoy GI pipe FD-220 or similar pattern:

Removing existing unserviceable long rail and S&F new long rail, fabricated from new 32mm dia bore GI medium grade pipe duly threaded as required as shown on drawing and fixed complete all as directed by Engineer-in-Charge.

Removing existing unserviceable short rail, fabrication of short rail from old long rail retrieved in replacement from item No. 1.01 above including threading as required as per Drg and fixed complete all as directed by Engineer-in-Charge.

Removing existing unserviceable leg, fabrication of leg from old short rail retrieved in replacement from item No. 1.02 above including threading as required as shown on drawing and fixed complete all as directed by Engineer-in-Charge.

Removing existing unserviceable elbow and S&F new elbow (ISI marked) suitable for 32mm dia bore GI pipe as per drawing and fixed complete all as directed by Engineer-in-Charge

Removing existing unserveceable check nut and S&F new check nut (ISI marked) suitable for 32mm dia bore GI pipe as per drawing and fixed complete all as directed by Engineer-in-Charge

Removing existing unserviceable stiffener and S&F new 900mm long MS stiffener made of flat iron 25x5mm and fixed complete all as directed by Engineer-in-Charge

Removing existing unserviceable ply top from GI pipe frame of charpoy, tightening/refixing the serviceable loose parts of the frame and S&F new 12mm thick BWP grade plywood of size 900mm wide x 1980 mm long in single piece, fixed with GI frame using 5mm dia 80mm long flush/countersunk bolts (10 Nos). Each bolt to be fitted with two cup washers & one nut by making/drilling hole of appropriate size in plywood and GI charpoy frame all as directed by Engineer-in-Charge

Charpoy hard top steel MAP Drg No. FD/MAP-II / 01 or similar pattern: Removing existing unserviceable part and S&F following similar new part with & including all necessary welding or other fixing accessories as per Drg, preparing new steel surfaces including welded portion and applying one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as directed by Engineer-in-Charge:-

Top plywood made of 12 mm thick BWP grade commercial plywood

Stiffener made of MS hollow section of size 25mm x 25mm x1.6mm thick

Leg made of MS hollow section 32mm x 32mm x 1.6mm thick welded with 32mmx32mmx5mm thick MS plate at bottom with 3mm thick rubber sheet fixed with adhesive.

Long rail made of MS hollow section of size 25mm x 65mm x 1.6mm thick.

Short rail made of MS hollow section of size 25mm x 65mm x 1.6mm thick including cleat made of MS hollow section of size 25mm x 60mm x 1.6mm thick to support the top plywood.

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish including touching up welded portion with one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note:- The welding required for fixing of new parts shall not be measured against this item. The same shall be deemed to be included in the quoted rate of the new part.

M&L for preparing old painted including newly replaced & painted steel parts surfaces of charpoy including removing dents/spots (if any), tightening the loose joints, cleaning the surfaces, rubbing with emery paper, filling the gaps with putty and applying one coat of synthetic enamel paint as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Locker steel Drg No. FD-1029 or similar pattern: Removing existing unserviceable part and S&F following similar new part with & including all necessary welding or other fixing accessories as per Drg, preparing new steel surfaces including welded portion and applying one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as directed by Engineer-in-Charge:-

Leg made of 1.00mm thick MS plain sheet

Shelf made of 1.00mm thick MS plain sheet

MS Conduit pipe 20mm dia bore chromium plated 1.6mm thick.

MS Handle 100mm long chromium plated

Hasp & staple made of chromium plated MS plain sheet of size 75mm x 40mm x 3mm thick

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish including touching up welded portion with one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note:- The welding required for fixing of new parts shall not be measured against this item. The same shall be deemed to be included in the quoted rate of the new part.

M&L for preparing old painted including newly replaced & painted steel parts surfaces of locker including removing dents/spots (if any), tightening the loose joints, cleaning the surfaces, rubbing with emery paper, filling the gaps with putty and applying one coat of synthetic enamel paint as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Table 3'x2' steel Drg No. FD-1008, 1007 or similar pattern: Removing existing unserviceable part and S&F following similar new part with & including all necessary welding or other fixing accessories as per Drg, preparing new steel surfaces including welded portion and applying one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as directed by Engineer-in-Charge:-

Hard Top made of 19mm thick exterior grade prelaminated particle board with decorative choice lamination on outside and other side with balancing white lamination with 6mm thick teak wood beading on edges duly polished complete

Leg made of MS hollow square section of size 25mm x 1.6mm thick.

Hard Rubber shoe

Top/Bottom long Stiffener made of MS hollow square section of size 25mm x 1.6mm thick.

Top/Bottom short Stiffener made of MS hollow square section of size 25mm x 1.6mm thick.

Drawer without lock made of 1.00mm thick MS plain sheet to shape as shown on drawing with standard PVC recessed handle.

Lock for Drawer, make- Godrej, Harison (for FD-1008 only )

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish including touching up welded portion with one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note:- The welding required for fixing of new parts shall not be measured against this item. The same shall be deemed to be included in the quoted rate of the new part.

M&L for preparing old painted including newly replaced & painted steel parts surfaces of table 3'x2' steel including removing dents/spots (if any), tightening the loose joints, cleaning the surfaces, rubbing by emery paper, filling the gaps with putty and applying one coat of synthetic enamel paint as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Table 3'x3' steel Drg No. FD-1009 or similar pattern: Removing existing unserviceable part and S&F following similar new part with & including all necessary welding or other fixing accessories as per Drg, preparing new steel surfaces including welded portion and applying one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as directed by Engineer-in-Charge:-

Hard Top made of 19mm thick exterior grade prelaminated particle board with decorative choice lamination on outside and other side with balancing white lamination with 6mm thick teak wood beading on edges duly polished complete

Hard Rubber shoe

Leg made of MS hollow square section of size 25 mm x 1.6mm thick.

Stiffener made of MS hollow square section of size 25 mm x 1.6mm thick.

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish including touching up welded portion with one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note:- The welding required for fixing of new parts shall not be measured against this item. The same shall be deemed to be included in the quoted rate of the new part.

M&L for preparing old painted including newly replaced & painted steel parts surfaces of table 3'x3' steel including removing dents/spots (if any), tightening the loose joints, cleaning the surfaces, rubbing by emery paper, filling the gaps with putty and applying one coat of synthetic enamel paint as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Table office clerk steel drg No. FD-1004 or similar pattern: Removing existing unserviceable part and S&F following similar new part with & including all necessary welding or other fixing accessories as per Drg, preparing new steel surfaces including welded portion and applying one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as directed by Engineer-in-Charge:-

Hard Top made of 19mm thick exterior grade prelaminated particle board with decorative choice lamination on outside and other side with balancing white lamination with 6mm thick teak wood beading on edges duly polished complete

Drawer without lock made of 1.00mm thick MS black sheet to shape as shown in Drg with standard PVC recessed handle.

Lock for Drawer, Make- Godrej, Harison

Leg made of MS hollow square section of size 25 mm x 1.6mm thick.

Top/Bottom long stiffener/rail made of MS hollow square section of size 25 mm x 1.6mm thick.

Top/Bottom short stiffener/rail made of MS hollow square section of size 25 mm x 1.6mm thick.

Hard Rubber shoe

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish including touching up welded portion with one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note:- The welding required for fixing of new parts shall not be measured against this item. The same shall be deemed to be included in the quoted rate of the new part.

M&L for preparing old painted including newly replaced & painted steel parts surfaces of table office clerk steel including removing dents/spots (if any), tightening the loose joints, cleaning the surfaces, rubbing by emery paper, filling the gaps with putty and applying one coat of synthetic enamel paint as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Table office officers steel Drg No. FD-1003 or similar pattern: Removing existing unserviceable part and S&F following similar new part with & including all necessary welding or other fixing accessories as per Drg, preparing new steel surfaces including welded portion and applying one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as directed by Engineer-in-Charge:-

Hard Top made of 19mm thick exterior grade prelaminated particle board with decorative choice lamination on outside and other side with balancing white lamination with 6mm thick teak wood beading on edges duly polished complete

Shutter made of 1.00mm thick plain MS sheet as shown on Drg with & including necessary hinges of suitable size.

Top/Bottom long stiffener/rail made of MS hollow square section of size 25 mm x 1.6mm thick.

Top/Bottom short stiffener/rail made of MS hollow square section of size 25 mm x 1.6mm thick.

Drawer without lock made of 1.00mm thick MS black sheet to shape as shown in Drg with standard PVC recessed handle.

Lock for Drawer, Make- Godrej, Harison

Hard Rubber shoe

M&L for spot / run welding (not exc 25mm in length) of steel items including scraping, preparing surface of welded portion, grinding where ever required to give smooth finish including touching up welded portion with one coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. Note:- The welding required for fixing of new parts shall not be measured against this item. The same shall be deemed to be included in the quoted rate of the new part.

M&L for preparing old painted including newly replaced & painted steel parts surfaces of table office officers steel including removing dents/spots (if any), tightening the loose joints, cleaning the surfaces, rubbing by emery paper, filling the gaps with putty and applying one coat of synthetic enamel paint as required to give uniform glossy finish complete all as specified and directed by Engr-in-Charge at furniture yard, Md / OTM accns under AOR of GE.

Locker bed side wooden Drg No. FD - 222 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Top / bottom ply with 19 mm thick BWR grade commercial plywood

Side Left/right ply with 19 mm thick BWR grade commercial plywood

Back ply made of 6 mm thick BWR grade commercial plywood

Shutter Left/Right made of 19mm thick BWR grade commercial plywood with 3mm thick teak wood edging alround.

Leg with frame complete made of Ist class hard wood (Teak wood)

Shelf made of 12 mm thick BWR grade commercial plywood with 3mm thick teak wood edging on exposed edges.

Shelf support bearer made of Ist class hard wood (Teak wood) of size 12mm x 20mm

Vertical sheet made of 12 mm thick BWR grade commercial plywood

Continuous (piano type) brass hinge 1.00 meter long of suitable width of flap as required

Hasp & staple made of stainless steel sheet of size 75mm x 40mm x 3mm thick

Handle 100mm size aluminium handle (ISI marked).

M&L for preparing / cleaning of old polished / newly replaced wooden parts & polished/painted surfaces of locker bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Book case wooden Drg No. FD-355 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Top/bottom sheet with 19 mm thick teak veneered BWR grade commercial plywood.

Sides Left/right sheet with 19 mm thick teak veneered BWR grade commercial plywood.

Back sheet with 6mm thick BWR grade commercial plywood

M&L for preparing / cleaning of old polished / newly replaced wooden parts & polished/painted surfaces of book case by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Hat stand with mirror Drg No. FD-361 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Peg of suitable size as shown on drawing made of copper oxidized steel

Mirror 5mm thick with teak wood beading.

Front veneer of 4mm thick BWR grade plywood fixed with decorative sheet of teak wood veneer colour

Back sheet of 12mm thick BWR grade plywood duly painted with one coat of synthetic enamel paint over one coat of primer.

35mm x 6mm thick teak wood beading on alround duly polished

Hanging clip of stainless steel

M&L for preparing / cleaning of old polished / newly replaced wooden parts & polished/painted surfaces of hat stand by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Table bed side wooden Drg No. FD-276 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Table top/bottom/shelf with 18/19mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick teak wood edging.

Left/right side planks with 12mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick teak wood edging.

Back side planks with 12mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick teak wood edging.

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Almirah large wooden full shelf Drg No. FD-109 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Back plank with 6mm thick BWR grade commercial plywood

Left/Right side plank with 18/19mm thick BWR grade commercial plywood

Left/Right Shutter with 18/19mm thick particle board with commercial veneer on both sides

Almirah top/bottom plank with 18/19mm thick BWR grade commercial plywood

Leg base with Ist class hard wood (Teak wood) of size as shown on drawing

Shelf with 12mm thick BWR grade commercial plywood

Hasp & staple made of chromium plated MS plain sheet of size 75mm x 40mm x 3mm thick

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Almirah Medium wooden Half hanging half shelf Drg No. FD - 108 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Back plank with 6mm thick BWR grade commercial plywood

Left/Right side plank with 18/19mm thick BWR grade commercial plywood

Left/Right Shutter with 18/19mm thick particle board with commercial veneer on both sides

Almirah top/bottom plank with 18/19mm thick BWR grade commercial plywood

Leg base with Ist class hard wood (Teak wood) of size as shown on drawing

Hasp & staple made of chromium plated MS plain sheet of size 75mm x 40mm x 3mm thick

Shelf with 12mm thick BWR grade commercial plywood

Hanging arrangement for cloth with 20mm dia bore stainless steel pipe fixed with brackets.

Centre vertical plank with 12mm thick BWR grade commercial plywood

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Bin soiled Linen Drg No. FD - 244 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Top ply with 6mm thick BWR grade plywood with teak veneer finish on top.

Canning to sides of bin soiled linen.

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Side Board Drg No. FD - 1112 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Shutter with 18/19mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 6mm thick teak wood edging.

Hard Top with 18/19mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick Ist class hard wood beading on all edges.

Left/right sides with18/19mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick Ist class hard wood beading on all edges.

Drawer made out of 12mm thick BWR grade commercial plywood with front side made out of 12mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick Ist class hard wood beading on top edges.

Back ply with 12mm thick BWR grade commercial plywood

Brass Knob with 25mm dia decorative type as per sample.

Bottom frame with 18/19mm thick BWR grade commercial plywood with teak veneers on both sides.

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Table wooden Drg No. FD-223 or simlilar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Hard Top with 18/19mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 6mm thick Ist class hard wood beading on all edges.

Leg without shoe made of Ist class hard wood (teak wood) of size as shown on drawing.

PVC shoe

Front/rear rail made of Ist class hard wood (teak wood) of size as shown on drawing.

Left/Right side rail made of Ist class hard wood (teak wood) of size as shown on drawing.

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Table office Officers wooden Drg No. DB - 4119 and simlilar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Leg frame complete made of Ist class hard wood (teak wood) of size as shown on drawing.

B L A N K

B L A N K

Left/Right side ply made of 12mm thick BWR grade commercial plywood as shown on drawing.

Drawer made out of 12mm thick BWR grade commercial plywood with front side made out of 12mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick Ist class hard wood beading on top edges.

Shutter with 12mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick Ist class hard wood beading on all edges including stainless steel hinges of suitable size.

Hard Top with 18/19mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 6mm thick Ist class hard wood beading on all edges.

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Table Office clerks Drg No. DB-4110 or simlilar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Leg frame complete made of Ist class hard wood (teak wood) of size as shown on drawing.

Bottom stiffener made of Ist class hard wood (teak wood) of size as shown on drawing.

Front/rear long rail made of Ist class hard wood (teak wood) of size as shown on drawing.

Left/Right side rail made of Ist class hard wood (teak wood) of size as shown on drawing.

Drawer made out of 12mm thick BWR grade commercial plywood with front side made out of 12mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick Ist class hard wood beading on top edges.

Shutter with 12mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick Ist class hard wood beading on all edges.

Hard Top with 18/19mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 6mm thick Ist class hard wood beading on all edges.

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Table Dressing Ladies wooden Drg No. FD- 251 & FD/MAP-II/07 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Looking mirror 5.5mm thick of size 366mm x 1220 mm

Back sheet of mirror with 6mm thick commercial plywood BWR grade.

Mirror frame made of 25mm x 19mm thick Ist class hard wood (Teak wood)

Drawer made out of 12mm thick BWR grade commercial plywood with front side made out of 12mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick Ist class hard wood beading on top edges.

Leg with support frame made of Ist class hard wood (Teak wood) for FD-251

25mm dia MS chromium plated knob for FD-251

5.5mm thick sliding glass for FD-251

Aluminium channel set of size 12 mm x 22 mm for sliding glass for FD-251

Bottom sheet of base frame made of 19mm thick Ist class hard wood (Teak wood) for FD-251

Left/right/partition sheet with 18/19mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination for FD-251

Back sheet with 6 mm thick BWR grade plywood for FD-251

Stool canned for FD-251

Stool cushioned for MAP pattern

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Table Dressing Gents wooden Drg No. FD-230 & FD/E6/MAP/16 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

5.5mm thick Looking mirror of size 380mmx760mm

Back sheet of mirror with 6mm thick commercial plywood BWR grade.

Mirror frame made of size 35mm x 25mm thick Ist class hard wood (Teak wood) complete

Bottom supporting frame made of size 35mm x 25mm thick Ist class hard wood (Teak wood)

Drawer made out of 12mm thick BWR grade commercial plywood with front side made out of 12mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination with 3mm thick Ist class hard wood beading on top edges for FD-230

25mm dia MS chromium plated knob for FD-230

Top with 12mm thick prelaminated particle board with decorative choice lamination on outer side and other side with balancing white lamination for FD-230

Left/right/partition sheet with 12mm thick BWR grade plywood fixed with teak wwof face veneers for FD-230

Bottom back sheet of base frame with 12mm thick BWR grade commercial plywood for FD-230

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

Chair CB Office Drg No. DB-4124 or similar pattern: Removing existing unserviceable part and S&F following similar new part with all necessary fixing accessories as per Drg including preparing new wooden surfaces and applying one coat of synthetic enamel paint over one coat of primer / french polish as applicable complete all as directed by Engineer-in-Charge:-

Canning of seat

Front/rear/left/right rail of seat made of Ist class hard wood (Teak wood)

Upper/lower Stiffener set of three of back support made of Ist class hard wood (Teak wood)

Stiffener set of three of leg bottom made of Ist class hard wood (Teak wood)

Front leg without PVC shoe made of Ist class hard wood (Teak wood)

Rear leg without PVC shoe made of Ist class hard wood (Teak wood)

PVC shoe

M&L for preparing / cleaning of old polished / newly replaced & polished wooden parts surfaces of table bed side by tightening all loose joints/parts as required, rubbing with emery paper, removing all spots/nail holes etc, filling with putty and applying one coat of synthetic enamel paint or french polish as required to give smooth and glossy finished surfaces complete at furniture yard / Md / OTM buildings under AOR of GE as directed by Engineer-in-Charge.

M/s R.K.Jain

TARUN ENGINEERING WORKS