Supply, Erection, testing & commissioning of 66kV D/C Becharaji-Vithalapur line on M/C Tower with ACSR Panther Conductor (AP-14 to AP-34) 11.86Rkm Under KSY Scheme.

Sr. No. Description of Works - SAC Code 9954 Amount in Rs.

PART -A Supply of Materials

Erection of Line

TOTAL F.O.R. COST WITHOUT GST

Service of "Works Contracts" GST @ 18% (SAC 9954)

TOTAL END COST WITH GST

I am / we are willing to carry out this service package of works contract stated above at GST 18% (in figure)

______ % (in words _____ %) below / above the estimated TOTAL END COST for all the items stated there in.

The amount of tender works out with above % (in figure) for TOTAL END COST Rs. _____________ (in words Rs.

I / we confirm that our above quoted rates are ON firm price basis; except supply of tower materials (including

nut-bolts) for which Price variation will be applicable.

1) Separation of the Contract into Supply of Goods, Services and Civil Work, is only for convenience and better

economical management and for the ease of Accountancy but the entire Contract, is to be assessed under GST

Law, as the Works Contract Service, which is, as per the provisions of Section 2(30), read with, Section 2(119),

further read with, Paragraph 6(a) of the Schedule II to the CGST Act, 2017 or SGST Act, 2017 and similar

provisions, applicable under the UTGST Act, 2017and the IGST Act, 2017 and the entire activity, would be

subjected to levy of Tax, at the rate of 9% CGST + 9% SGST or 18% IGST, under the GST Law. However,

Classification Codes for different segments or portions of the Works Contract, may be specified separately, in the

Supplies, with a final common Classification Code of Works Contract Service.

2) The Bidder is hereby conveyed that only SAC Code and Tax rate for supply of Service Works Contract i.e.

18% is relavant for the purpose of contract since the contract is works contract and any separation in the works

is for better management and convenience purpose.

It is to state that bidders are however requested to fill the HSN code item by item for the knowledge and

transparency purpose which shall have no bearing on price or taxation payment.

Signature of Authorized Representative of Company / Agency

SEAL & SIGNATURE Status _________________

OF BIDDER Name of bidder Company

Estimated Cost - SUPPLY

Supply, erection, testing & commissioning of 66kV D/C Becharaji-Vithalapur line on M/C Tower with ACSR Panther Conductor (AP-14

to AP-34) 11.86Rkm under KSY Scheme.

Tender No.-ACE(P&C)/Contract/E-503/TL/66kV/S&E

Sr. Description of Supply with Detail HSN / Unit Qty Unit Rate Unit Freight, Unit FOR Unit FOR Total Cost

No. Specification of Service Package - SAC Packing & Insurance Rate (Excl. GST)

Works Contract (SAC Code 9954) code Forwarding Charges in Rs. in Rs.

for charges in Rs.

A Supply of Materials

A.1 Tower Materials

A-2 AL-59 (Equivalent to Panther) conductor kM 0.000 328767.00 4264.00 1828.00 334859.00 -

A-3 ACSR Panther conductor kM 0.000 234904.00 2867.00 1229.00 239000.00 -

A.3 Silicone Rubber insulators - 66kV -

A.3.3 66kV,90kN - Suspension SRI Nos. 116 1615.00 12.00 5.00 1632.00

A.4 Insulator hardware for AL-59 -

(Equivalent to Panther) conductor

A.4.1 Single suspension Nos. 0 1666.00 37.00 16.00 1719.00 -

A.4.2 Double suspension Nos. 0 3916.00 103.00 44.00 4063.00 -

A.4.7 Vibration damper Nos. 0 603.00 25.00 11.00 639.00 -

A.4.8 Repair sleeve Nos. 0 323.00 6.00 2.00 331.00 -

A. Insulator hardware for ACSR -

Panther conductor

A.4.1 Single suspension Nos. 90 1564.00 17.00 7.00 1588.00

A.4.2 Double suspension Nos. 12 4413.00 34.00 15.00 4462.00

A.4.4 Double tension Nos. 24 4945.00 51.00 22.00 5018.00

A.4.6 Mid span joint Nos. 40 695.00 6.00 3.00 704.00

A.4.7 Vibration damper Nos. 432 572.00 11.00 5.00 588.00

A.4.8 Repair sleeve Nos. 7 252.00 6.00 3.00 261.00

A.6 OPGW - 24 Fibre (220kV) -

A.6.1 24 Fibre (DWSM) OPGW fibre Optic cable Km 0.000 145356.00 1999.00 857.00 148212.00 -

A.6.2 Installation Hardware set * & Km 0.000 45351.00 502.00 215.00 46068.00 -

accessories for above OPGW i.e. all

cable fittings & accessories like

suspension clamps, tension clamps,

vibration dampers, earthing clamps,

down lead clamps, in-line splice

enclosures etc. including; Pigtails FC-

a) Fibre Optic Approach Cable -

400 Mtrs - For 220KV S/S &

500 Mtrs - For 400KV S/S

(with installation hardware like ties/

clips / cleats, conduits, ducts,

supports, fittings, accessories etc).

(Any variation in quantities shall be

absorbed by contractor)

A.7 OPGW - 48 Fibre (220kV) -

A.7.1 48 Fibre (DWSM) OPGW fibre Optic cable Km 12.000 195533.00 2385.00 1022.00 198940.00

A.7.2 Installation Hardware set * & Km 12.000 48279.00 644.00 276.00 49199.00

accessories for above OPGW i.e. all

cable fittings & accessories like

suspension clamps, tension clamps,

vibration dampers, earthing clamps,

down lead clamps, in-line splice

enclosures etc. including; Pigtails FC-

a) Fibre Optic Approach Cable -

400 Mtrs - For 220KV S/S &

500 Mtrs - For 400KV S/S

(with installation hardware like ties/

clips / cleats, conduits, ducts,

supports, fittings, accessories etc).

(Any variation in quantities shall be

absorbed by contractor)

TOTAL COST FOR MATERIALS

Service of "Works Contracts" GST @ 18% (SAC 9954)

1) Separation of the Contract into Supply of Goods, Services and Civil Work, is only for convenience and better economical management and for

the ease of Accountancy but the entire Contract, is to be assessed under GST Law, as the Works Contract Service, which is, as per the

provisions of Section 2(30), read with, Section 2(119), further read with, Paragraph 6(a) of the Schedule II to the CGST Act, 2017 or SGST Act,

2017 and similar provisions, applicable under the UTGST Act, 2017and the IGST Act, 2017 and the entire activity, would be subjected to levy of

Tax, at the rate of 9% CGST + 9% SGST or 18% IGST, under the GST Law. However, Classification Codes for different segments or portions of

the Works Contract, may be specified separately, in the Supplies, with a final common Classification Code of Works Contract Service.

2) The Bidder is hereby conveyed that only only SAC Code and Tax rate for supply of Service Works Contract i.e. 18% is relavant for the

purpose of contract since the contract is works contract and any separation in the works is for better management and convenience purpose.

It is to state that bidders are however requested to fill the HSN code item by item for the knowledge and transparency purpose which shall have

no bearing on price or taxation payment.

Signature of Authorized Representative

of Company / Agency

SEAL & SIGNATURE Status _________________

OF BIDDER Name of bidder Company

ERECTION PORTION

Tender No.-ACE(P&C)/Contract/E-503/TL/66kV/S&E

Description of Supply with Detail Specification of Service FOR Total Cost

SN Package - Works Contract (SAC Code Unit Quantity Unit Rate (Excl. GST)

B ERECTION OF LINE

B-1 Schedule-1 (Tower line)

The work of detail survey, preparation and submission of profiles in

6 copies (PLSCAD as well as hardcopy),

Detail scope of Work :-

(a) Fixing of tower as per actual requirement, site condition and

plotting of line on profile having standard details i.e. span length,

lat-long (co-ordinate), chainage, weight and wind span, all

dimensions, scale, legends, tower spotting data etc. as per

requirement and along with all require details.

(c) Preparation and submission of tower schedule as per standard

require details with all the Major - Minor crossing details in profile

drawing and tower schedule, along with due care of clearance as per

1 prevailing standards i.e., for all electric line with pole, all type of kM 12.000 10222

track, river, pond, nala, road, canal etc.

(d) Details of Right of Way in profile drawing. i.e. Building, Temple,

(g) Plotting line on TIKKA-MAP (Revenue Land map) - Required

TIKKA-MAP will be provided by GETCO.

Importantly, any work other than mentioned will align with the

specific requirements outlined by the Engineer-in-Charge.

Note : The survey report will be submit with sign and stamp of the

surveyor agency and engineer in charge.

Check Survey along with plotting of line route on village (tika) map

with Coordinates including detailed survey, preparation of profiles

and revision in original route alignment, if any and as per

instruction of EIC.

Excavation excluding back filling, but including shoring, shuttering,

dewatering, tree cutting for tower footings etc. for:-

a) Normal soil either dry or wet / Sandy soil. CMT 3656.250 307.00

b) Black Cotton Soil either dry or wet. CMT 8925.330 614.00

c) Normal submerged / marine soil where dewatering is necessary. CMT 0.000 484.00 -

d) Black cotton submerged / marine soil where dewatering is

e) Soft Rock CMT 0.000 1066.00 -

f) Hard Rock CMT 0.000 2212.00 -

Installation of steel reinforcement in concrete foundation

including supply of GETCO Approved M.S. bars, binding wire. Work

4 also includes their cutting, bending, shaping and binding with MT 112.688 99900.00

binding wire and fixing in position of TMT bars as per drawing before

the concrete work and as per instruction of the EIC

Stub-setting with prop or template including back-filling, during

back filling dispose of excess soil and levelling of site is to be done

as per instructions of EIC but excluding excavation and concreting

etc. for all types of towers/extensions except special towers.

(Weight of stub, cleat & template with Bolt & Nuts of stub &

template shall be counted)) up to 6 mtr extension. (SOR Part-A -6)

6 ---- Do ---- up to 9 to 25 mtr extension MT 0.000 9918.00 -

Concreting of foundation by M20/M15/M25 mixture including

shoring, shuttering, compaction, dewatering etc. for normal tower /

tower with extension upto 25mtr.

After completion of concrete work, curring (watering to concerte) is

Grounding of towers with pipe type earthing including

excavation and back filling, with supply of all materials like 32mm

8 dia heavy duty 3 mtr. long G.I. Pipe, 50 x 6 mm G.I. flat, GI bolt- Set. 52 8985.00

nuts, with GI spring washer, salt, charcoal etc. as per drawing and

as per instruction of EIC.

Grounding of towers with COUNTER POISE TYPE including

9 excavation and back-filling and supply of all materials like GSS wire, Set. 0 15756.00 -

lugs, bolt-nuts, salt, coke/charcoal as per drawing.

Erection of super structure upto 6 meter extension including tree

cutting, fixing of tower accessories, attachments except ACD /DP

/NP /CIP /PP and excluding tack welding of bolts as per instruction

10 of EIC. This includes taking delivery of tower materials and bolt- MT 457.687 10076.00

nuts from GETCO’s stores etc. for normal, extension & special

towers at destination and keeping them in safe custody and

transporting the same to erection site.

Same as above but erection of 9/12/15/18/21/25 mtr. Extention

Fixing of Anti-climbing devices including supply of barbed wire

as per drawing and as per instruction of EIC.

Fixing of DP / NP / PP / CIP including supply of plates and supply

of G.I. bolts-nuts & tack welding as per drawings and as per

instruction of EIC.

Tack welding of nuts upto approx. 10 mtrs. height OR two bottom-

most panel from ground level at three places on the nuts Per

diametrically and applying zinc rich paint immediately after tack Bolt

welding and as per instruction of EIC.

Complete Installation of OPGW cable (24/48 fibres) including laying,

providing required hardwares, in line splices to be encased in Fibre

Optic Splice Enclosures, Laying and termination of a fibre optic

approach cable required to connect Overhead Fiber Optic Cable

(OPGW) between the final iin line splice enclosure on the

gantry/tower and the Fibre Optec Distribution panel (FODP) to be

installed within the building at both the substation ends as per

technical specifications

Link up of OPGW Cable including all related activities as per inst. Of

Stringing of ACSR/ AAAC 12 (Six) conductors for Multi circuit

including laying, jointing, tensioning, clamping with armour rods,

hoisting of insulator string fixing of jumpers, dampers etc. & with RKM 0.000 225856.00 -

required tree cutting on entire length for adequate clearances / safe

charging of line, as per instruction of EIC.

Stringing of ACSR/ AAAC 6 (Six) conductors for double circuit

including laying, jointing, tensioning, clamping with armour rods,

hoisting of insulator string fixing of jumpers, dampers etc. & with

required tree cutting on entire length for adequate clearances / safe

charging of line, as per instruction of EIC.

Stringing of ACSR/ AAAC 3 (Three) conductors for single circuit

including laying, jointing, tensioning, clamping with armour rods,

hoisting of insulator string fixing of jumpers, dampers etc. & with RKM 0.000 161057.00 -

required tree cutting on entire length for adequate clearances / safe

charging of line, as per instruction of EIC.-For Hot Line stringing

Stringing of ACSR/ AAAC 3 (Three) conductors for single circuit

including laying, jointing, tensioning, clamping with armour rods,

18 hoisting of insulator string fixing of jumpers, dampers etc. & with RKM 0.000 56464.00 -

required tree cutting on entire length for adequate clearances / safe

charging of line, as per instruction of EIC.

Termination and connection for making LOOP-IN-LOOP-OUT

arrangement with existing line during specified outage including

restringing of existing conductors OR dismantalling / new stringing

for making LILO arrangements with existing line or for change over Job

line as per approved LILO arrangement in profile as per instruction Work

of EIC in COLD CONDITION and dismentalled materials to be

credited to near by GETCO's store or sub station as per inst. of EIC.

To make necessary arrangements for fixing of 3 Nos. of through

(parallel / bypass) jumper provide at any location of newly erected /

existing line of (66kV / 132kV / 220kV) as per instruction of EIC.

Firewadge and conductor for the same work will be provided by

GETCO at free of cost, but agency has to take it from GETCO's store Job

and credit back the balance materials. Only Fire wadge connector 0.000 9354.00 -

will be fixed by special authorized person with using of firewadge

fixing gun only and same will be arranged by GETCO.

- D/C Line Only

Work of Painting of Line name, Location No., two coat Painting

Color code of desired length and telephone no. on Tower Leg with

19 letter of Gujarati language using ISI marked Paint as per instruction per loc 0.000 862.00 -

of EIC including Supply of paints and other require materials.

a) All four legs - For 4 Nos. of Line (M/C)

b) All four legs - For 2 Nos. of Line (D/C)

c) Two legs - For 1 Nos. of Line (S/C)

TOTAL COST PART - B, SCHEDULE WITHOUT GST

Service of "Works Contracts" GST @ 18% (SAC 9954)

TOTAL COST PART - B WITH GST

1) While calculating the weight of stub-setting, the weight of stub, cleat & templetes shall also be added in stub weight.

2) Red oxide & zinc rich paint shall be applied after tack welding of nuts.

3) The above rates are with supply of cement by the contractor.

4) The rate indicated above includes taking delivery of all stringing materials from Board / Contractor store at destination keeping them in safe

custody and transporting the same to erection site.

1) Separation of the Contract into Supply of Goods, Services and Civil Work, is only for convenience and better economical management and for the ease of

Accountancy but the entire Contract, is to be assessed under GST Law, as the Works Contract Service, which is, as per the provisions of Section 2(30), read

with, Section 2(119), further read with, Paragraph 6(a) of the Schedule II to the CGST Act, 2017 or SGST Act, 2017 and similar provisions, applicable under the

UTGST Act, 2017and the IGST Act, 2017 and the entire activity, would be subjected to levy of Tax, at the rate of 9% CGST + 9% SGST or 18% IGST, under the

GST Law. However, Classification Codes for different segments or portions of the Works Contract, may be specified separately, in the Supplies, with a final

common Classification Code of Works Contract Service.

2) The Bidder is hereby conveyed that only only SAC Code and Tax rate for supply of Service Works Contract i.e. 18% is relavant for the purpose of contract

since the contract is works contract and any separation in the works is for better management and convenience purpose.

It is to state that bidders are however requested to fill the HSN code item by item for the knowledge and transparency purpose which shall have no bearing on

price or taxation payment.

Signature of Authorized Representative

of Company / Agency

SEAL & SIGNATURE Status _________________

OF BIDDER Name of bidder Company