PROVN OF CERTAIN COLLAPSIBLE SHUTTER AT OKHA GRIT PLASTER AT CERTAIN LOCATION OF OKHA GARBAGE BIN AT VARIOUS LOCATION OF OKHA OTHER BR MINOR WORKS AT VARIOUS LOCATION OF OKHA, CERTAIN SANCTIONED JOB MISC WORK AT RESTRICTED AREA OF VADINAR UNDER OKHA

Amount

SCHEDULE 'A'

Supply & installation and tesing of High galvanized mast light of 15 mtr height suitable for 12 lantern symmetrically fitted, 3 mm section thickness, top dia 150mm, bottom dia 340 mm along with their control gear and having two point suspension system with stainless steel wire rope of 6 mm dia 97/19 guage and double drum winch with luminaire mounting arm, pully assembly, lightning arrester spike including RCC/PCC foundation as per height.complete all as specified and directed by Engr-in-charge at site Make: Utkarsh/bajaj or quivalent

M&L for bore Earthing 150 mm bore for earthing with galvanised steel pipe electrode, 40mm bore, medium grade, 2.5 metres length,top edge of GI pipe 15 cm above GL , connected with earthing lead of 25X4 mm GI strip to the earthing test point and filling of charcol dust , salt etc and testing on completion, complete all as specified and directed by Engr-in-Charge. Note: IR Value should be kept .less than 5 Ohms.

M&L for bore Earthing, 150 mm bore for earthing with maintenance free chemical earthing using copper electrode of size 19 mm dia - 01 No, 3 m long, Copper earth strip including excavation and earth work, back fill with compound (Chemical for earth enhancer gel 2 x 25Kg) - 01 set complete all as directed, by Engineer in charge. Note: (i) IR Value should be less than 1.0 ohm. (ii) Copper earth stip of size 32 x 6 mm including installation 7.5 Mtr (Copper purity not less than 99%) is deemed to be included in the unit rate. (iii) Suitable FRP Chamber should be included in the unit rate.

Supply and fix for LED Flood light 210 Watt made from Pre die cast aluminium housing having Luminous flux 21000 lm with system efficiency not less than 110 lm/watt at 5700 K havin IP 66 protection with surge protection 4 KV internal and 10 KV external, THD < 10% including SS Nuts, Bolts and Washers and connecting wire 2.5 sqmm/ 3 core complete all as specified and directed. Make :- PHILIPS Cat No.BVP483 LED210 CW NB PSU GR or its equivalent in Wipro.

Supply, installation ,testing and commissioning for LED Aviation light (2 ffitting per mast is necessaty if no taller structure are in near vicinity) suitable for LED lamp 4-5 watt by means of base plate and GI Pipe with dash fastner, toughened heat resistant glass neoprene complete all as specified and directed. Make: Bajaj Cat No.BGAV 302 LED or its equivalent in Crompton/Philips .

Supply, laying and testing for XLPE cable Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of following sizes:-

95 Sqmm 3.5 core

70 Sqmm 3.5 core

50 Sqmm 3.5 core

25 Sqmm 4 core

16 Sqmm 4 core

Excavation in trenches not exc 1.5 m wide and not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed

Excavation in trenches not exc 1.5 m wide and not exc 1.5m in depth and getting out in Soft/disintegrated rock complete all as specified and directed

Returning filling with soil/rock in incl spreading levelling watering and well ramming in layers not exc 25 soft cm thick complete all as specified and directed

Removing excavated material not exc 50 m and depositing where directed at a level not exc 1.5 m from above the starting point complete all as specified.

Supply and lay double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 ( Part I and II) for protection of underground cables laid in trenches / road/ nallah or fixed along wall poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc for cable protection all as specified of following size with all fittings.

63 mm outer dia

50 mm outer dia

M & L for LT panel Board cubical KIOSK Outdoor type compact 415 Volts AC 50 Hz, fabricated of Thermoplastic (Polycarbonate), insulated, shock proof, dust proof, water proof, anticorrosive and confirming to IP 65 complete including Copper bus bar of 160 Amp capacity 4 strip mounted on porcelain insulated & enclosed in chamber & connection from incoming and out going with openable shutter both sides comprising of following :- Make of Panel: Hensel/Neptune Make of MCCB/MCB : Schneider/Legrand

(a) Incoming - MCCB 100 Amp FP 16 KA - 01 No

(b) Outgoing - MCCB 63 Amp TP 16 KA- 01 Nos

(c) MCCB 40 Amp TP 16 KA- 02 No

(d) MCB 32 Amp TPN, 10 KA - 02 Nos

(e) Street light timer 20A capacity with contactor ML-2

(f) Digital panel meter for Amp, Volt,KWH, power factor and other parameter flush mounting of size 96 x96 mm NOTE : (a) The contractor should submit the IP Test Report and Verification of shor circuit withstand Test report issued by CPRI in respect of LT Panel (b) Contractor shall submit the drawing for approval prior to place the order

M&L for cutting existing road/hard standing not exc 45 x 45 cm in wide & depth getting out excavated material for laying cable/GI tube, returning filling & well rammaing watering finish suraface 10 cm from top using PCC 1:2:4; including removal of surplase soil complete all as specified and directed.

Complete removal of existing treatment from wall surfaces as directed.

M&L for granules textured homogeneous wall finishing system including preparation of old surfaces consisiting of a two component system of dry granules (25 Kg per Pack) made of 92% silica particles coated with fade resistant pigment, 100% acrylic polymerbonding agent (5 Kg per pack ) with the applied thickness of the coating being between 0.8mm - 1.2 mm to be applied on curved, smooth level plaster without key, as per manufacture directions, for usages to be applied and approved applicator of the manufacture as per the ddirection/ supervision of the Engineer -in-Charge, all complete, The above texture coating should confirm to surface spread of flame class one of BS 476 : Part 7 : 1971 and pull off strength of the coating to meet JISA 6909 on smooth plastered surfaces all as specified and as directed by Engr-in-Charge. Make : Bakelite Hylam Limited or equivalent make approved by the GE

Surface dressing n exe 15 cm deep in Hard/Dense soil complete all as specified and directed,

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone agregate) as foundations , filling and mass concrate in type D2 , 1:4:8 ( 40 mm graded aggregate )

M&L of hard core of gauge n exc 63 mm, deposited, spreaded and levelled in layers n exc 15 cm thick water and rammed to a true surface complete all as specified and directed.

M& L , PCC 1:3:6 type C-1 (using 20mm graded stone agregate)Pre - cast cement concrete block masonry with solid blocks , exc , 10 cm in width and setting in mortar , complete all as specified .

M&L for frame works as in doors or gates of angle or other section with gusset plates , rails , braces , etc , complete , drilled for fixing of steel sheeting or other covering . Doors etc . To be prepared for hanging or sliding with and including either hooks and hings or steel hanging door fittings (exclusive of steel sheeting or other covering , running rails and complete all as specified and directed.

M& L for two coat of synthetic enamel paint over a coat of primer on steel surface exc 10cm width complete all as specified and directed.

M&L for Reinforced concrete pipes , class NP2. laid and jointed complete as in chimney 200 mm dia

M&L for treatment At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

M&L Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L for Cutting channels, grooves or rebates exc 15 cm but n exc 30cm girth into concrete, tiles floor etc complete all as specified and directed.

M&L for Cutting holes in brick walls in mud mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

S&F for Stainless steel collapsible gate, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles, holdfasts (06) Nos etc as specified, erected in position and securing runners in holdfastsand brackets complete all as specified and directed.

roxy enterprise

Harsh Infrastructure

shree chamunda enterprise

JAMNAGAR ELECTRIC AND MACHINERY CO