09/SE(EC)/W and S/KMDA(2nd call) of 2022-2023

Amount

A. LUMP SUM PRICES FOR THE MAIN PLANT RAW WATER INLET ARRANGEMENTS INCLUDING INTER CONNECTION WITH DEPARTMENTAL RAW WATER RISING MAIN BY INSTALLATION OF FLOW CONTROL VALVES.

Civil Works

MAIN AND SECONDARY FEED CHANNELS AND / OR PIPES FOR DELIVERING WATER TO FLASH MIXER AND CLARIFIERS INCLUDING ARRANGEMENTS FOR FLOW MEASUREMENTS INCLUDING RAW FLOW METER, CONTROL SLUICE GATES FOR FLOW REGULATION AND CLARIFIER BYPASS AND SLUICE VALVE FOR FILTER BY PASS.

Civil Works

CHLORINATING ARRANGEMENTS FOR PRE AND POST CHLORINATION.

Civil Works

CHEMICAL HOUSE AND DOSING EQUIPMENT INCLUDING : COAGULANT AGITATORS COAGULANT SOLUTION STRAINERS LOCAL LEVEL INDICATOR COAGULANT DOSING EQUIPMENT ALUM HOISTS ALUM CHARGING BASKETS HAND CARTS 1000 KG. WEIGHING MACHINES LIQUID COAGULANT TANK CONSTRUCTED AT GROUND LEVEL OF CHEMICAL HOUSE& NECESSARY PUMPING ARRANGEMENT FROM COAGULANT TANK TO COLLECTION WELL TO BE PROVIDED WITH ROTAMETER. WATER AND COAGULANT SOLUTION PIPING LABORATORY FURNITURE & SINKS

Civil Works

FLASH MIXING CHAMBERS INCLUDING C.I. SLUICE / PRENSTOCKS, EQUIPMENT FOR FLASH MIXING AND DESLUDGING ARRANGEMENTS.

Civil Works

06 NOS MECHANICAL FLOCCULATOR UNITS ALONG WITH ALL ALLIED CIVIL/ELECTROMECHANICAL & WASHING ACCESSORIES COMPLETE IN ALL RESPECT INCLUDING CHANNELS OR PIPES TO PLATE SETTLER UNIT AS PER REQUIREMENTS.

Civil Works

06 NOS PLATE SETTLER UNITS ALONG WITH ALL ALLIED CIVIL/ELECTRO –MECHANICAL & WASHING ACCESSORIES COMPLETE IN ALL RESPECT INCLUDING CHANNELS OR PIPES TO FILTER HOUSE AS PER REQUIREMENTS.

Civil Works

FILTER HOUSE WITH 06 NOS TWIN TYPE FILTER BEDS WITH REQUIRED SAND BED AREA AND ENTRANCE BUILDING WITH EQUIPMENT INCLUDING. INLET AND OUTLET PIPING PNEUMATICALLYOR ELECTRICALLYOPERATED SLUICE VALVES AND SLUICE GATES. FILTER FLOOR EQUIPMENT AND FILTER MEDIA OUTLET CONTROLLERS / FILTRATE OUTLET ARRANGEMENTS. SLOW START EQUIPMENT. LOSS OF HEAD AND RATE OF FLOW INDICATORS. FILTER CONTROL TABLES BACKWASH WATER PUMPS INCLUDING MOTORS AND PIPING. EQUIPMENT FOR DRAINING OF LIGHT PARTICLES OF IMPURITIES SURFACE WASH DEVICE. AIR BLOWERS INCLUDING MOTORS AND PIPING WASH WATER METER.

Civil Works

ARRANGEMENTS FOR REUSE OF FILTER WASTE WATER INCLUDING PUMPS AND PIPING.

Civil Works

FLOW METER FOR MEASURING FILTERED WATER OUTPUT.

Civil Works

PLANT WASTE WATER DISPOSAL SYSTEM WITH MINIMUM 300 MM DIA C.I. PIPES WITH 2 NOS SLUICE GATES OF REQUIRED SIZE, WITH SUBMERCIBLE PUMPS WITH SPECIAL INTAKE ARRANGEMNT FOR PUMPING SUPERNATANT SLUDGE WATER FROM SLUDGE PONDS TO COLLECTING WELL.

Civil Works

LABORTORY EQUIPMENTS, SAMPLING TABLE AND TOOL BOX CONTAINING TOOLS AND ELECTRICAL EQUIPMENTS. CHLORINE GAS HANDLING SAFETY TOOL BOX WITH UNIFORMS AND GAS CYLINDER (2 NOS) WITH MASKS.

Civil Works

SCALED MODEL (1:200) AND ANIMATED FLOW DIAGRAM

Civil Works

FILTERED WATER CONVEYANCE SYSTEM WITH CONNECTION TO 1.5 MG UGR FROM FILTER HOUSE.

Civil Works

ANNUNTIATION PANEL FOR MOTOR CONTROL CENTRE.

Civil Works

EQUIPMENT FOR MOTOR CONTROL CENTRE INCLUDING STARTERS FOR ALL MOTORS.

Civil Works

ROAD WEIGH BRIDGE (30MT CAPACITY) WITH COMPUTER PRINTING FACILITY.

Civil Works

LEVELLING AND GRADING OF THE SITE IN THE PLANT AREA INCLUDING RAIN WATER DRAINAGE, SURFACE DRAINAGE AND APPROACH ROAD (4M WIDE- CONCRETE PAVER BLOCK OVER WBM / CONCRETE PAVEMENT/BITUMINOUS PAVEMENT AS PER DIRECTION OF EIC OR COMPIEENT AUTHORITY) TO SITE & DIFFERENT UNITS OF WTP.

Civil Works

C.I. /R.C.C. SLUDGE PIPELINE OF MINIMUM 300 MM DIA FROM SLUDGE PRODUCING UNITS TO SLUDGE TANKS AND NECESSARY PENSTOCK GATES AND VALVE ARRANGEMENT FOR FILIING OTHER LOW LAND AREAS.

Civil Works

2.1M HIGH RCC FRAMED MASONRY BOUNDARY WALL WITH BARBED WIRE AND THREE MS ORNAMENTAL GATES ALONG WITH CURVED GLOW SIGN BOARD ON GATES IN THE BOUNDARY OF WTP

Civil Works

DESIGNING , DRAWING, PROVIDING AND CONSTRUCTION OF A COVERED RCC UNDERGROUND CLEAR WATER RESERVOIR OF UNDISTURBED CAPACITY OF 1.5 MG IN TWO CPMPARTMENTS WITH THREE PENSTOCK GATES OF SUITABLE SIZES AS APPROVED . ADEQUATE NOS COWL VENTS, APRON INCLUDING COST OF DEEP CAST-IN-SITU RCC PILES, EARTH WORK IN EXCAVATION AND FILLING WITH THE EXAVATED AND GOOD CARRIED EARTH OF APPROVED QUALITY AS MAY BE REQUIRED, SAND FILLING, SHORING/ SHEET PILLING, DEWATERING, COST OF TWO NUMBERS BUTTERFLY VALVES, WELL POINTS ETC. ALL COMPLETE AS PER SPECIFICATIONS GIVEN IN THE TENDER DOCUMENTS (VOLUME I) AND AS PER APPROVED DRAWINGS AND DIRECTION OF THE EIC. A) PILING WORK INCLUDING PILE TESTING B) ALL OTHER WORKS

Civil Works

DESIGNING , DRAWING, PROVIDING AND CONSTRUCTION OF A PUMP HOUSE FOR WET PIT PUMPS AND MOTORS AND ALLIED BUILDINGS INCLUDING EOT CRANE (7.5 MT) & Auxiliary HOT (2MT) crane, FOUNDATIONS AND SPACES AS PER DRAWINGS AND SPECIFICATIONS, UNLOADING BAY, COMMON PUMP SUMP AS SHOWN IN TENDER DRAWING INCLUDING THE COST OF DEEP CAST-IN-SITU RCC PILES, EARTH WORK IN EXCAVATION AND FILLING WITH THE EXAVATED AND GOOD CARRIED EARTH OF APPROVED QUALITY AS MAY BE REQUIRED, SAND FILLING, SHORING/ SHEET PILLING, DEWATERING, WELL POINTS ETC. ALL COMPLETE AS PER SPECIFICATIONS GIVEN IN THE TENDER DOCUMENTS (VOLUME I) AND AS PER APPROVED DRAWINGS AND DIRECTION OF THE EIC. A) PILING WORK INCLUDING PILE TESTING B) ALL OTHER WORKS INCLUDING EOT CRANE

Civil Works

DESIGNING , DRAWING, PROVIDING AND CONSTRUCTION OF A SUB-STATION BUILDING OVER PILE FOUNDATION

Civil Works

CONSTRUCTION OF 2 NOS SLUDGE POND OF EACH CAPACITY 3832 CUM WITH RCC LINING

Civil Works

CONNECTION WITH PROPOSED RAW WATER RISING MAIN OF 750 MM DIA WITH MS 750MM DIA OF LENGTH 10M (APPROX.) AND 1 NO MS PIPE OF 800MM DIA AS CLEAR WATER CONVEYANCE MAIN BEYOND CWR OF LENGTH 15 M (APPROX.)

Civil Works

Dewatering, Site clearances by old structures and levelling of the area after development of site with carried earth /silver sand up to formation ground level.

Civil Works

Electro-Mechanical Works: Part-I WTP

Supply ,fitting , fixing & commissioning of inlet pipe along with 2 nos . BFV as required and other accessories , etc .to complete the collecting well as per CPHEEO guideline and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of ultra-sonic flow indicator along with other accessories, cabling , etc as required at the venturi flume portion as per CPHEEO guideline and as per satisfaction of the EIC.Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the entire electro mechanical parts , of flash mixture etc as required as per CPHEEO guideline and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the entire electro mechanical parts , gates , flocculators, motors, panels , weirs, ultra sonic flow sensor , plates & scrapper (in case of plate settlers) , clariflocculator bridge and carriage mechanism including drive , flocculator drives, paddles all complete ( in case of clariflocculator ) , desludge system , etc as required to complete the job as per CPHEEO guideline and as per satisfaction of the EIC.Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the entire electro mechanical parts , gates , valves , under drainage system ,control console, level sensors, flow control system etc as required at the filter bed portion of the filter house , all complete as per CPHEEO guideline and as per satisfaction of the EIC.Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the entire electro mechanical parts like recirculation pump, blower, backwash pump (or OHR filling pump in case of constant head tank type back washing ) , air compressor for pneumatic valves if required , pre & post chlorination pump, OHR filling pump, alum dosing pump, surface wash pump, de-watering pump, crane or hoist , supernatent pump, as required etc. along with all the accessories as required to complete the job as per CPHEEO guideline and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the entire electro mechanical portion like the Substation , Power distribution board (PDB) , Motor control Center (MCC), Control desk, APFC panel , Inverter, UPS , cabling , trays , MIMIC , Instruments, sensors, meter, earthing etc. along with all accessories as required as per CPHEEO guideline and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the entire electro mechanical portion of the sludge disposal system / re-circulation system , including sludge pumps, blowers , valves , diffusers, MCC, etc all complete including centrifuge if required, supernatent pumps, submersible pumps, pipe lines, hoist , etc. all complete as required as per CPHEEO guideline and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the entire electro mechanical portion of the chemical house including pre and post chlorination system including chlorinators, alum dosing system including alum agitators , poly dosing system if required, hoists, weighing machine, SS alum lifting trays, toners, trunions, chlorine leak detection system , neutralizing system , dosing pumps , rotameters, safety equipments etc. as required to complete the chemical house as per CPHEEO guidelines and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the entire electro mechanical portion of the laboratory including all meters and instruments etc . as per CPHEEO guidelines and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the entire electro mechanical portion of the pitless weigh bridge as required and as per CPHEEO guidelines and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the electro mechanical portion the ultrasonic flow meter at the outlet of the clear water channel of the filter house leading to the UGR of the CWPS as per CPHEEO guidelines and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply ,fitting , fixing & commissioning of all the entire indoor and out door illumination , earthing, glow sign , indications ets as per IS standard and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Electro-Mechanical Works: Part-II CWPS

Supply, delivery at site and installation of vertical turbine pump motor set complete having the following head discharge characteristics , capable to discharge clear water ,having SS(CF8M) impeller, CI casing , dischagre head ,motor stool along with other standard accessories with TEFC 1000 rpm(synchronous),6Pole, 3 Phase, 6.6 /11 kv ± 10% AC. Insulation class F , IP 55 , Squirrel Cage Induction motor of suitable ratings as required and as per technical specification and direction of EIC and as per CPHEEO standard . Motor shall have a margin of 1.3 over the pump BKW at duty point. Pumps shall be installed on suitable RCC foundation adhering to all the technical requirements of the pump manufacturer. Make : Pump :WPIL / Mather & Platt / KBL . Motor :CGL/Marathon/Siemens/ABB

i) 1000m³/hr against a tentative head of 55 to 60 MWC (2 no working +2 no. Standby )

(Finally actual TDH to be determined by the tenderer at the time of detailed engineering after consultation with the concerned division dealing with the pipe laying )

Supply, delivery at site, installation of 2-Panel HT Switch Board of 350 MVA, 11 KV 18.4 KA , 800 Amps complete in all respect with all other accessories as per technical specification and direction of EIC. Make : Schneider/ Siemens / ABB /Andrew Yule (For KMDA HT Room , if required as per layout)

Supply, delivery at site, installation of minimum 1500 KVA, 11/0.433KV as required (To be finalised during detail Engineering ), ONAN outdoor Transformer complete in all respect with all other accessories as per technical specification and direction of EIC conforming to IS :1180 ( 1no. Working + 1no. Standby ) Make : KEC / Schneider / Siemens/ABB

Supply, delivery at site, installation of LT. P.D.B. complete in all respect with all other accessories as per technical specification and direction of EIC. Make : Sellwin Electricals Pvt. Ltd. / PCE Project Pvt. ltd / System Control/Sun Shine & Control Pvt Ltd./ Industrial Switch Gear Pvt. Ltd. . ( 2 nos. incomer ACB , 1 no. bus coupler , 2 nos. WTP ACB feeder,2 nos feeders for CWPS, Lighting feeders, Valve actuator feeder , EOT crane feeder, and other auxiliary loads as required & also with APFC Panel fitted to it ,and as per technical specification and direction of EIC ).

Supply, delivery at site, installation of LT. MCC complete in all respect with all other accessories as per technical specification and direction of EIC. Make : Sellwin Electricals Pvt. Ltd. / PCE Project Pvt. ltd / System Control . ( 2 nos. incomer ACB , 1 no. bus coupler , 6 nos feeders with soft starter of adequate rating along with other auxiliary loads as required as per technical specification and direction of EIC ).

Supply, delivery at site, installation of central control desk complete in all respect with all other accessories as per technical specification and direction of EIC.

Supply, delivery at site, installation of 110Volt DC Battery Charger with maintenance free battery complete in all respect with all other accessories as per technical specification and direction of EIC.(capacity to be determined during detailed engineering.)

Supply, delivery at site , fitting and fixing of electro-magnetic flow meter of following sizes , comprising of flow sensor and transmitter, signal conditioner if required, flow indicator, flow totaliser(controller unit ) and all other accessories complete as per specification and direction of EIC. I) 600 MM

Supply, delivery at site fitting and fixing of following MS pipe including fabrication of all necessary accessories special viz dismantling joints, Puddle plates(20mm), Bell Mouth, bends, tees, enlarger/reducer, R.C.C. pedestal for common manifold , etc including cutting walls, pipes, making flanged & welded joints as required, fitting fixing complete in all respect including cost of all fitings, sundry and jointing materials as required for laying of pipe with anti-corrosive treatment of all pipe surface complete as per technical specification and direction of EIC.

400 mm, 8/10mm thick (For individual delivery piping)

400 mm, 8/10mm thick DF Metallic dismantling joint with split flange, long stud, bolts, nuts etc.

600 mm , 10mm thick (For common manifold piping)

600 mm , 10mm thick (For flowmeter piping)

Supply, delivery at site, lowering, fitting and fixing of DIDF non return valve (PN-1.6 ) of following size in proper position and alignment by providing temporary support as required including cost of all sundry materials such as gaskets, nuts, bolts etc. all complete as required to complete the job in all respect as per technical specification and direction of EIC.

400 mm, dia (for individual pump delivery side)

Supply, delivery at site, lowering, fitting and fixing of DIDF butterfly valve (PN-1.6) alongwith suitable rated motorised actuator of following size in proper position and alignment by providing temporaray support as required including cost of all sundry materials such as gaskets, nuts, bolts etc all complete as required to complete the job in all respect as per technical specification and direction of EIC.

400 mm dia with head stock (for individual pump delivery line)

600 mm dia (for common header )

Supply, delivery at site, fitting and fixing of gun metal gate/globe / check valve for dewatering & drinking water lines complete with accessories including cost of all sundry materials and fitting fixing charges as required as per technical specification and direction of EIC.

50mm dia Gate / Globe Valve

32mm dia Gate / Globe Valve

50mm dia Check Valve

Supply, delivery at site, fitting and fixing of single orifice type air release valve with isolation valve of adequate size for manifold pipe line complete with all other standard accessories including cost of all sundry materials and fitting fixing charges as required as per technical specification and direction of EIC.

Supply, delivery at site, fitting and fixing of dust & damp proof following field instruments complete with all valves, cocks and other fixtures including cost of all sundry materials as required as per technical specification and direction of EIC.

0-10 kgf/cm² (6" dial bourdon type for individual delivery line,accuracy ± 1%)

0-10 kgf/cm² (8" dial bourdon type for common delivery manifold,accuracy ± 1%)

Pressure transmitter including cabling (For individual delivery line )

Pressure transmitter including cabling (For common delivery manifold )

Supply, delivery at site fitting and fixing of the ultra sonic water level sensor with indicator including transmitter / transducer / stilling pipe and all other accessories including all cabling connections all complete as per specification and direction of EIC (Quantity-2 Nos).

Supply, delivery at site fitting and fixing of float type mechanical level indicator and staff including all other accessories as per specification and direction of EIC.(Quantity-2 Nos).

Supply ,delivery at site and laying of 11 KV grade XLPE insulated, PVC outer sheathed, armoured, aluminium conductor cable of following size either through cable duct or through cable trays or through protection pipes as per technical specification and direction of EIC.

3 core x 300 mm² ( CESC room to KMDA HT room to transformer yard ) .

Supply, delivery at site and laying of 1.1KV / 11 KV grade XLPE / PVC insulated, PVC outer sheathed, armoured, aluminium conductor cable of following size either through cable duct or through cable trays or burried underground through brick protection or through protection pipes as per technical specification and direction of EIC.

3.5 core x As required mm² TXR(LT) to LT panel.

3 core x As required mm² HT motor feeder to motor terminal

Supply, delivery at site and laying of 1.1KV grade XLPE insulated, PVC outer sheathed, armoured, stranded copper conductor auxiliary power and control cable of following size either through cable duct or through cable trays or through protection pipes as per technical specification and direction of EIC.(minimum 2.5 mm² ) Including signal cable.

Making end termination of 11KV grade 3 core x 300 mm² XLPE insulated, PVC outer sheathed, armoured, aluminium conductor cable with push on type premoulded cable jointing kit indoor/ outdoor type as required complete with gland and other hardwares as per direction of EIC.

Making end termination of 1.1KV grade XLPE/PVC insulated armoured Al./Cu. conductor cable with gland and other hardwares of following sizes as per direction of EIC

Earthing the whole installation as per IE Rules & Acts, specifications, complete in all respect including supply,installation of all required earthing materials,flats,earth electrodes and all other sundries,fitting,fixtures including making proper earth stations as per technical specification and direction of EIC.

Providing fencing with structural gates around the periphery of the transformer yard as per I.E. rules including supply and fixing of necessary M.S. angles, flates G.I. mesh etc. as required to complete the job as per specification and direction of EIC.

Supply and fixing of E.I. Danger board on wall & fencing as per direction of EIC

Supply and providing 11KV grade rubber mat as per direction of EIC.

Supply and fixing on wall a shock treatment chart duly framed by polished wood and the glass fitted in front complete as per direction of EIC.

Display of back lit & non lit sign board of various sizes on the pump house wall fascia or elsewhere as per direction of EIC.

Supply ,installation & commissioning, of 7.5 MT double girder capacity EOT crane complete in all respect including testing as per technical specification and direction of EIC.

Painting the whole installation as per technical specifcation and direction of EIC.

Carrying out high pressure test of the HT installation by approved agency and obtaining necessary clearance fron Directorate of Electricity as per direction of EIC.

Supplying ,fitting , fixing & commissioning of all the entire indoor and out door illumination , earthing, glow sign , indications ets as per IS standard and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply of drawings for approval and finally as-built drawings in 6 sets and CDs .

Supply, delivery at site & laying of MS pipe including fabrication of all necessary accessories special ,enlarger, ,R.C.C. / fabricated pedestal , thrust blocks , etc including cutting pipes, making flanged & welded joints as required, for joining the common delivery manifolds with the existing prelaid rising main pipes complete as per technical specification and direction of EIC. Note : Any mechanical or electrical or civil , parts/spare/equipment not included in the BOQ but required to complete the project is to be supplied by the agency at free of cost .

Trial run 3 months and commissioning of the entire installation as per specification and direction of EIC.

O&M OF THE WTP & CWPS FOR 60 MONTHS AFTER SUCCESSFUL COMPLETION OF TRIAL RUN OF THREE MONTHS AFTER THE CERTIFIED DATE OF COMMISSIONING OF THE ENTIRE PLANT (3 MONTHS TRIAL RUN + 60 MONTHS OPERATION MAINTENANCE) TOTAL 63 MONTHS WITH TRAINED STAFF, SUPPLY OF COAGULANTS, DISINFECTANT AND LABORATORY REAGENTS TO RUN THE PLANT TO ITS DESIRED CAPACITY

Civil Works

Electro- Mechanical Works

GBC INFRASTRUCTURE PRIVATE LIMITED

G B CONSTRUCTION