Provn of barbed wire fencing with iron angle and iron gate 5.5 feet around unit parade ground and adequate security light facilities Qty10 at MH Ramgarh Cantt Appx length 120 Mtr), Provn of Boundary wall at GGH In OFFRs Mess Bldg No T 4 PRC Provn of

Amount

Excavation in post holes in hard and dense soil (or similar holes) each n.exc. 0.5 Cum getting out, returning, filling in and ramming earth around, in layers n.exc 25cm etc., complete all as directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m depth for foundation, and getting out, and getting out in soft/loose soil, complete all as directed. (4.5+40+43.56)

M & L for PCC (1:4:8) type D2 40mm graded stone aggregate as in foundation filling and mass concrete etc., Complete all as specified. (0.45+5+3.74+5.04)

M & L for PCC (1:2:4) type B2 40mm graded stone aggregate as in foundation filling and mass concrete etc., Complete all as specified.

S & F Fe-290 Gde E-165, mild steel tube joist, channel, angle, Tee section fixed independently, with connecting plates, etc. (cut to ordinary lengths i.e within 20mm of the length indicated) all as specified and directed.

M & L in applying two coats of synthetic enamel paints over a coat of red oxide primer on steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed by Engr-in-Charge. (33+15)

M & L for steel kitchen racks (Over all size in inch 31"x30"x10") including all fixing materials and making good to disturb surfaces etc., all as directed by Engr-in-charge.

S & F for galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2mm dia at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc., complete all as specified and as directed.

M & L for RCC(1:1.5:3) type A-1 using 20mm graded stone aggregate as in plinth beam, lintel beam, roof beam etc., complete all as specified and as directed.

M & L for formwork to sides and soffits of plinth beam lintel beam, roof beam etc., complete all as specified and as directed. (9+73)

S & F mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping, hooking ends and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips, complete all as specified and directed. (90+1920)

S & F mild steel TMT bars 8mm dia and over cut to length, bent to shape required including cranking bending with MS wire (annealed) not less than 0.90mm dia or securing with clips as in stirrups, complete all as specified. (20+656.09)

M & L for brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 Kg/Sqcm) old size bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6), complete all as specified and as directed.(1+8.5)

M & L 15mm thick rendering in cement mortar (1:4) on fair faces of brickwork finished surface even and smooth using WPC mixed with cement, without using extra cement, complete all as specified and as directed. (WPC shall be measured and paid separately) (6.4+87)

M & L for preparation of newly plastered surface and applying two coats of cement base paint over a coat of white wash, complete all as specified and as directed. (6.4+240+87)

Supply only integral water proofing compound conforming to IS 2645-1975 of an approved make. (2.5+20)

M & L for brick work with fly ash bricks old size bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6), complete all as specified and as directed.

M & L for Damp proof course to horizontal or vertical surfaces including necessary formwork in PCC (1:2:4) type B-0, 25mm thick, complete all as specified and as directed. (14+4.39)

M & L for plain cement concrete 1:3:6 type C-1, using 20 mm graded stone aggregate as in coping, complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brickwork or concrete in cement mortar (1:4) finished even and fair, complete all as specified and as directed.

M & L for rendering 15mm thick on other fair faces of brickwork or concrete in cement mortar (1:4) finished even and fair, complete all as specified and as directed.

M & L framed work as in door or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering doors, etc., to be prepared for hanging or sliding with and including etither hooks and hinges or steel hanging door fittings, and hanging also fastening and fixing complete.

Excavation in trenches, exceeding 1.5m wide and not exceeding 3.00m depth for foundation, and getting out, and getting out in soft/loose soil, complete all as directed.

M & L for moorum/red bajri filling in floors or pavings, laid in floors n.exc 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M & L for RCC M-25 using 20mm graded stone aggregate, design mix for footing, raft footing etc., complete all as specified and as directed.

M & L for RCC M-25 using 20mm graded stone aggregate, design mix for column, plinth beams, lintel beams, roof slab and roof beams etc., complete all as specified and as directed.

M & L for formwork to soffit of suspended slab such as roof slab, floor slabs n.exc 200mm thick, complete all as specified and as directed.

M & L for formwork to edges of concrete flats, treads, breaks in floor etc, exc 10cm but n.exc 20 cm, complete all as specified and as directed.

M & L for rendering 15mm thick on fair faces of brickwork or concrete in cement mortar (1:6) finished even and fair, complete all as specified and as directed.

M & L for rendering in cement mortar (1:3) on fair faces of cement concrete on ceiling of thickness 5mm finished the surface even and smooth without using extra cement, complete all as specified and as directed.

M & L preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for 100 mm thick D2 (1:4:8) 40mm graded aggregate as in sub base floor, complete all as specified and as directed.

M & L for hard core of broken stone of gauge n.exc 63 mm, deposited, spread and levelled in layer n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed. (7+8)

M & L for 100mm thick PCC (1:2:4) type B-2, using 40mm graded stone aggregate as in path, floor finishing surface even and fair without using extra cement, including spike rolling to surface making impressions of expanded metal, while the surface is green, complete all as specified and as directed. (115.04+5.04)

M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 using 20mm graded stone aggregate as in plinth protection, finishing the surfaces even and smooth without using extra cement, complete all as specified and directed.

M & L for 10mm thick screed bed in cement mortar(1:3) with WPC @ 3% by weight of cement (WPC shall be measured and paid separately) and applying 3mm thick APP modified polymeric water proofing membrane having standing weight 3.2 to 3.5 Kg/Sqm shall be laid and bonded to the sub-strata by heat process, overlap shall sealed/fused by flame torch as per manufacturer's instructions with 100mm side lap over bituminous based primer conforming to IS:3384-1965 @ 0.30 Ltrs/Sqm till the roof surface is impregnated. APP modified polymeric membrane shall be covered with bituminous based aluminium paint @ 0.20 Kg/Sqm in two coats over non approachable roof slabs, complete all as specified and as directed by Engr-in-Charge.

Surface excavation n.exc 30cm deep and averaging 15cm deep and geeting out in hard/dense soil, complete all as specified and as directed.

Forming construction joint 30mm deep x 10 mm wide filled with sealing compound grade A, complete all as specified and as directed.

M & L for Steel tubular swaged poles, complete with cast iron base plate, finial taper plug, bolt, nuts & screws as specified type 410 SP-31 (09 metres long) including aluminium painting, complete all as specified and as directed.

S&F 40 mm dia bore galvanize iron pipe light grade, bent to shape of length 1.50 mtr with flat iron clamp of size 50 mm x 6 mm nuts and bolts of 12 mm dia 100 mm long including washer duly painted with two coat of synthetic enamel paint over a coat or red oxide primer on mild steel surface including preparation of surface including and fixing on pole /wall complete all as specified and directed.

M & L Earthing complete with galvanised steel earth plate electrode 60 cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25m deep below ground level) top edge of the plate not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm as earthing lead by means of bolts nuts check nuts and washers of galvanised iron, protected by GI pipe 15mm bore (light grade) and watering pipe 20mm bore GI pipe (light grade) and PCC of chamber and coping shall be in 1:3:6 type C-1 using 20mm graded stone aggregate including excavation and earth work and removal surplus soil and filling with black cotton soil upto ground level, complete all as shown in Electrical plate No. 3 of SSR Part-I, 2009 with CI cover 10mm thick of size 300 x 300 mm with charcoal dust and common salt complete and earth lead connected to panell including testing complete all as specified and as directed. Note: Earthing test result should not be less than one Ohm.

Supplying and laying or fixing or passing through pipe, 1100 Volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathing 4 Sq. mm 2 core nominal cross sectional in service connections, including testing complete all as specified and as directed.

Supplying and laying or fixing or passing through pipe, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 Volts grade, cross-sectional area 6 Sq. mm 4 core in stranded conductor, including testing complete all as specified and as directed

Excavation, in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for laying cable/pipes and getting out in hard/dense soil complete alll as specified and as directed.

Removing excavated materials n.exc 50 m and depositing, where directed at a level n.exc 1.5 m above the starting point, complete all as specified and as directed. (13+15+13.94)

Returning, filling in trenches including spreading, levelling watering and well ramming in layers n.exc 25 cm thick, complete all as specified and as directed. (14+25+32.52)

M & L for plain cement concrete 1:3:6 type C-2, using 40 mm graded stone aggregate as in foundation, filling and mass concrete for stay pole etc., complete all as specified and directed.

M & L for PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in coping and the like including weathering lightly rounded or chamfered angle and use and waste of formwork, complete all as specified.

M & L for reinforced precast concrete cable cover class LV, type 2, flat, size 300mm x 180 mm x 40 mm , complete all as specified and as directed.

M & L for clean and dry sand free from sharp material in trenches around the cable for cushioning complete (depth 23 cm and after punning down to 18 cm) complete all as specified and as directed.

M & L for painting three strip alternative layer width 20mm with black, yellow, black of radium/photosynthetic paint on steel tubular poles etc., after preparation of old surfaces on coping of pole, complete all as specified and as directed.

M & L for flood light pressure die cast with IP-66 protection, efficient high output emitter LED 50 Watts 230 volts, 50 Hz. Make Crompton CAT Part No. LFLE-50-CDL or equivalent in Bajaj/Syska including connecting in existing circuit with flexible wire 2 core, 2.5 Sqmm Aluminium conductor 1.5 metre long, complete all as specified and and directed.

S & F thermoplastic cable junction box IP-66 halogen free and weather proof with terminals suitable for 10 Sq mm dimension 167mm x 125 mm x 82 mm (CAT part No. KF 5105, of Make Hensel), complete with all fixing accessories including testing all as specified and as directed.

S & F of street light panel 6 KW load with digital 24 hour timer with contactor 32 Amp/TP along with MCB 40 Amp, SPN complete all as specified and as directed. Make : Havells Cat part No. IHXSS01060 or of equivalent in L & T/HPL/Siemen as approved by GE.

M & L for point wiring for one light/ fan point/call bell controlled by one switch with 1100 volt grade PVC insulated FRLS 1.5 Sq mm multi stranded copper conductor cable with continuous earth wire of 1.5 Sq mm multi stranded copper conductor cable PVC insulated-unsheathed, drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 20 mm dia & sunken anodized pressed sunken boxes made out of not less than 1.0 mm thick sheet, covered with 2.8 mm thick laminated insulated cover make sheet for housing/fixing switches etc complete all as specified and directed.

All as per item No. 56 here-in-before but 1.5 Sqmm for 5 Amp socket outlet on the same board with 1.5 Sq mm earth wire.

All as per item No. 56 here-in-before but 2.5 Sqmm for 15 Amp switch socket combination on independent board with 2.5 Sq mm earth wire, complete all as specified and as directed.

S & F for switch piano type 5 amp 230 volt one way flush type, complete all as specified and as directed.

S & F ceiling rose three terminals PVC/ Polycarbonate, isolated body complete all as specified.

S & F socket outlet 3/5pin 5 Amp flush type 230 volt complete all as specified.

S & F switch socket combination 2 in 1, 6 pin 5 Amp and 15 Amp flush type universal 230 volt complete all as specified.

S & F angle holder complete all as specified and as directed.

S & F 9W LED lamp, complete all as specified.

S & F LED tube light batten suitable for LED T-8 lamps (Cat part No- DMLN1T8-16) pre-wired with LED tube rod 16 W ( Cat part No- LTT8-16) with extruded aluminium body PC diffuser and inbuilt driver of Crompton Greaves or equivalent model of Philips/ Wipro/GE including electrical connection from ceiling rose to light fitting by PVC flexible wire 23/.0076 mm size including earth connection complete.

S & F sheet metal enclosures for DBs single pole & neutral 4 way double door with 200 Amp rated bus bar suitable to accommodate MCB and necessary electric cable connection through suitable lugs by crimping and making good disturbed area of wall complete all as specified and as directed.

S & F MCB single pole 6 to 32 Amp 240 V, ‘B’ Series, 10 KA, complete all as specified and as directed.

S&F in repair MCB SPN, 20 to 40A 240V, ‘B’ Series, 10 KA complete all as specified and as directed.

Supply in repair 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, two single core cable flat or circular stranderd conductor 6 Sq mm including testing complete all as specified and directed.

M/S Bhushan Kumar Jain

M/s Ray construction