Development of Central Tasar Nursery and Tasar Silk Park at Khuntagaon TRC, Lahunipada, Sundargarh

Revised BOQ TASAR

REVISED BILL OF QUANTITIES (BOQ) including GST

SL.No DESCRIPTION AMOUNT In Rs.

1 CIVIL AND PHE WORK 183266844.42

2 EXTERNAL DEVELOPMENT 9425103.81

3 DRAIN AND UGR 12535078.55

4 BOUNDARY WALL 13192241.96

5 LIFT WORKS 2049037.67

6 ELECTRICAL 38422656.30

7 EQUIPMENT 28523548.26

8 FIRE MANAGEMENT SYSTEM 2071012.68

10 SIGNAGE 1245298.88

11 FURNITURE WORKS 5409600.00

TOTAL AMOUNT PUT TO TENDER 297682560.39

TOTAL AMOUNT PUT TO TENDER 297682560.39

BIBHU DUTTA Digitally signed by

BIBHU DUTTA MISHRA

MISHRA Date: 2021.04.29

CIVIL AND PHE WORKS

Sl. Item Description Unit Rate Quantities Amount

A.- Civil Works:-

1 Earth work excavation in hard soil or gravelly soil within 50m. Intial lead and 1.5 m.

intial lift including rough dressing and breaking clods to maximum 5cm. To 7cm and

laying and layers not exceeding 0.3m in depth and as per direction of the department.

2 Extra lift of 1.5m. or part there of over the initial depth of 1.5m. in all kinds of

embankments, road works and

ordinary earth works in general.

1st extra lift of 1.5m. (Up to 7.5m.) CUM 16.80 1380.96 23200.13

3 Extra lead of 25m. or part there of over the initial lead of 50m. for earth work in all

kinds of embankment, road works and ordinary earth work in general. (a) 50m. to

4 Filling in foundation and plinth with excavated materials including watering and

ramming as directed by the Engineer-in-charge. CUM 114.99 1599.17 183889.31

5 Supplying and filling sand in foundation and plinth including watering , ramming,

consolidating and dressing, labours, tools, taxes etc. all complete as per the

specification and direction of E.I.C. (Ground Floor)

6 Pre-Constructional Anti-Termite Treatment works :

6.1 Supplying, diluting and preparing chemical emulsion like CHLOROPYRIPHOS or other

chemicals as approved by central Insectcides Board or as directed by the manufacturer

and spraying the mixture uniformly by sprayer as pre-constructional anti-termite

treatment and creating a chemical barrior under and around wall trenches, basement

excavation, top surfaces of plinth filling,junctions of wall and floors along with external

perimeter of the building surrounding the pipes and conduits etc. complete at the rate

of 7.5 litres ( or as directed by the manufacturer) per sqm on vertical and @ 5.0 litre

per sqm on horizontal surfaces, 50% of the emulsion to be filled in the holes made in

trenches at 150mm centre to centre etc. complete as per IS 6313/1981(Part-II) and as

per the direction of the Engineer-in-charge including all cost of materials labour, taxes

etc all complete.

6.2 Supplying, laying 10micron Polythene membrane over compacted sand filling in plinth,

before laying plain cement concrete (1:4:8).

7 Plain Cement Concrete works :

7.1 Providing and Laying plain cement concrete 1: 4: 8 .( 1 cement : 4 sand : 8 stone

Aggregate 40mm nominal size ) As levelling course in foundation and plinth etc.

complete all depth and height. CUM 4738.72 763.28 3616970.20

7.2 2.5cm. damp proof course with C.C. (1:2:4) using 12mm. size crusher broken granite

8 Reinforced Cement Concrete works :

8.1 R.C.C. work of M-25 grade with 20mm & down grade size black hard granite (crusher

broken) chips including hoisting and laying.

In Ground Floor including Foundation :

8.2 R.C.C. work of M-25 grade with 20mm & down grade size black hard granite (crusher

broken) chips including hoisting and laying.

In First Floor : CUM 5856.48 796.74 4666062.59

Sl. Item Description Unit Rate Quantities Amount

8.3 R.C.C. work of M-25 grade with 20mm & down grade size black hard granite (crusher

broken) chips including hoisting and laying. In 2nd Floor Level :

9 Centering & Shuttering works :

(i) For centering and shuttering for R.C.C. work (in floor and roof slab, Landings,

Balconies, projecting sunshades, Chajja, Stairs Plinth band,footings , base of columns,

precast slab, beams and columns, Lintels,R.C.C. Walls and Fins) in first floor and

subsequent upper floors add 20 percent extra to the rate of respective centering and

shuttering items over and above the rates from the next lower floor.

9.1 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in ground floor.:

(i) R.C.C. Floor roof slabs, landings, balconies, projecting sun-shades and chajjas upto

9.2 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in First floor.:

(i) R.C.C. Floor roof slabs, landings, balconies, projecting sun-shades and chajjas upto

9.3 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in Second floor.:

(i) R.C.C. Floor roof slabs, landings, balconies, projecting sun-shades and chajjas upto

9.4 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in ground floor.:

R.C.C. stairs excluding landing but including railing

9.5 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in First floor.:

R.C.C. stairs excluding landing but including railing

9.6 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in ground floor.:

R.C.C. foundation and plinth band, footings, bases of columns, mass concrete, precast

9.7 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in ground floor.:

R.C.C. beams, columns, girders and bressmers etc.

9.8 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in First floor.:

R.C.C. beams, columns, girders and bressmers etc.

9.9 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in Second floor.:

R.C.C. beams, columns, girders and bressmers etc.

Sl. Item Description Unit Rate Quantities Amount

9.10 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in ground floor.:

9.11 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in First floor.:

9.12 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in Second floor.:

9.13 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in Ground floor.:

R.C.C. walls and fins including attached pilastes

9.14 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in First floor.:

R.C.C. walls and fins including attached pilastes

9.15 Rigid and smooth centering and shuttering for R.C.C. works including false work and

dismantling them after casting including cost of materials complete in Second floor.:

R.C.C. walls and fins including attached pilastes

10 Reinforcement works :

10.1 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete with Thermo-Mechanically Treated bars of grade Fe-

In Ground Floor QTL 9065.34 3169.00 28728048.11

10.2 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete with Thermo-Mechanically Treated bars of grade Fe-

In First Floor QTL 9088.19 1121.15 10189195.78

10.3 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete with Thermo-Mechanically Treated bars of grade Fe-

In Second Floor QTL 9111.15 522.68 4762213.64

11 MASONRY BRICK WORK WITH 25CM. BRICKS :

11.1 Brick work with Fly ash bricks of 25 Cm. x 12 Cm. x 8 Cm. size having crushing strength

not less than 75 Kg./Cm2 with dimensional tolerance ± 2 % in cement mortar (1:6) in

foundation and plinth. CUM 4873.12 570.94 2782247.88

11.2 Brick work with Fly ash bricks of 25 Cm. x 12 Cm. x 8 Cm. size having crushing strength

not less than 75 Kg./Cm2 with dimensional tolerance ± 2 % in Cement mortar 1:6 (1

cement : 6 coarse sand) in Super structure In Ground Floor above Plinth level :.

11.3 Brick work with Fly ash bricks of 25 Cm. x 12 Cm. x 8 Cm. size having crushing strength

not less than 75 Kg./Cm2 with dimensional tolerance ± 2 % in Cement mortar 1:6 (1

cement : 6 coarse sand) : in 1st Floor :.

11.4 Brick work with Fly ash bricks of 25 Cm. x 12 Cm. x 8 Cm. size having crushing strength

not less than 75 Kg./Cm2 with dimensional tolerance ± 2 % in Cement mortar 1:6 (1

cement : 6 coarse sand) in 2nd Floor :.

Sl. Item Description Unit Rate Quantities Amount

11.5 Half brick masonry with non modular fly ash bricks of class designation 10,

conformingio IS :12894, in super structure above plinth and upto floor V level.: In

Cement mortar 1 : 4 (1 cement : 4 coarse sand) SQM 712.32 3914.88 2788644.47

11.6 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

course of half brick masonry. SQM 1067.36 3914.88 4178582.05

12 Wood & PVC works :

12.1 Dressed seasoned sal wood work framed and fixed (Wrought and put up) in trusses

purlins frames of doors, windows ventilators and beams

12.2 Providing and fixing factory made uPVC door frame made of uPVC extruded sections

having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (±

0.2 mm), corners of the door frame to be Jointed with galvanized brackets and

stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the

frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm)

wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per

manufacturer’s specification and direction of Engineerin-charge.

Extruded section profile size 42x50 mm

12.3 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood

and well matched commercial 3 ply veneering with vertical grains or cross bands and

face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

12.4 25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded

PVC section of the size of 762 mm X25 mm or less as per requirement with an average

wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided

on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having

dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of

the door. Core of the door shutter should be filled with High Density Polyurethane

foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size

25 mm X 11 mm. Door shutter shall be reinforced with special polymeric

reinforcements as per manufacturer’s specification and direction of Engineer-in-charge

to take up necessary hardware and fixtures. Stickers indicating the locations of

hardware will be pasted at appropriate places

12.5 Stair case Railing :

Steel work welded in built up sections/ framed work, including cutting,

hoisting, fixing in position and applying a priming coat of approved steel

primer using structural steel , MS Tubes as hand rail, etc. as required as per drawings..,

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

13 ALUMINIUM WORKS :

Sl. Item Description Unit Rate Quantities Amount

13.1 Supplying, fitting, fixing up window (sliding type)made up aluminum Section 151-154,

151-155, aswindows frame section No. 151-155, 151-153 and 151-167 as shutter frame

with 5mm thick blackglass as panel fitted with rubber bending including locking

arrangement including all fitting including cost of materials all taxes labour, T&P etc.

complete as per direction of Engineer-in-charge.

13.2 Providing fitting, fixing of Al. door with 60 micron powder coated Al. door section of

9202 as vertical member, 9201 as top member and 9200 as bottom and middle

member and 6mm plain glass in top portion with 12mm thick pre-laminated board in

bottom portion fixed on door frame by means of tapered clip No. 4660 and the frame

to be completed by means of jointing angle No. 1855 including all cost of labour, T&P,

hire charges of drilling machine, labour charges etc. complete

13.3 Providing and fixing aluminium work for doors, windows, ventilators and partitions

with extruded built up standard tubular sections/ appropriate Z sections and other

sections of approved makeconforming to IS: 733 and IS: 1285, fixing with dash

fasteners ofrequired dia and size, including necessary filling up the gaps atjunctions,

i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc.

Aluminium sections shall be smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat angle, Aluminium snap beading for

glazing / paneling, C.P.brass / stainless steel screws, all complete as per architectural

drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash

fasteners to be paid for separately) :For fixed portion:

Powder coated aluminium (minimum thickness of powder coating 60 micron)

13.4 Providing and fixing glazing in aluminium door, window, ventilator shutters and

partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the

architectural drawings and the directions of engineer-in-charge .

(Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

13.5 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S.

flats, square or round bars etc. including priming coat with approved steel primer all

Fixed to openings /wooden frames with rawl plugs screws etc. Kgs 127.68 12357.76 1577838.67

13.6 Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron

and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings

complete, including applying a priming coat of approved steel primer.

Using flats 30x6mm for diagonal braces and central cross piece.

14 DOOR - WINDOW FITTINGS :

14.1 Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6

levers and a pair of lever handles of approved quality with necessary screws etc.

14.2 Providing and fixing chromium plated brass handles with necessary screws etc.

Sl. Item Description Unit Rate Quantities Amount

14.3 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating

not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or

shade, with nuts and screws etc. complete : 300x16 mm.

14.4 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not

less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or

shade, with necessary screws etc. complete : 300x10 mm each

14.5 Providing and fixing bright finished brass hanging type floor door stopper with

necessary screws, etc. complete. EACH 104.16 54.00 5624.64

14.6 Providing and fixing aluminium die cast body tubular type universal hydraulic door

closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto

35 kg and door width upto 700 mm), with necessary accessories and screws etc.

14.7 Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of

handles (best make of approved quality) for aluminium windows including necessary

cutting and making good the windows etc. complete as per architectural drawing &

direction of Engineer-in-charge.

15 FLOORING WORKS :

15.1 Kota Stone Flooring

15.1.1 Kota Stone Flooring in Stair risers & skirtings :

Fixing Kota Tiles of minimum 16 mm thick , in dado, skirting and rises of steps on

12mm. thick cement plaster 1:3 (1 cement : 3 sand) joined with neat cement slurry

mixed with pigment to match the shade of the tiles including rubbing and polishing

complete including cost of precast tile. . - In Ground Floor.

15.1.2 Kota Stone Flooring in Stair risers & skirtings :

Fixing Kota Tiles of minimum 16 mm thick , in dado, skirting and rises of steps on

12mm. thick cement plaster 1:3 (1 cement : 3 sand) joined with neat cement slurry

mixed with pigment to match the shade of the tiles including rubbing and polishing

complete including cost of precast tile. . - In First Floor.

15.1.3 Kota Stone Flooring in Floor, Stair Landing & Treads :

Fixing Kota Tiles of minimum 16 mm thick in floors, treads on steps and landing on

25mm. thick bed of cement mortar 1:1 (1 cement : 1 sand) joined with neat cement

slurry mixed with pigment to match the shade of the tiles including rubbing and

polishing complete including cost of precast tile.)- In Ground Floor

15.1.4 Kota Stone Flooring in Floor, Stair Landing & Treads:

Fixing Kota Tiles of minimum 16 mm thick in floors, treads on steps and landing on

25mm. thick bed of cement mortar 1:1 (1 cement : 1 sand) joined with neat cement

slurry mixed with pigment to match the shade of the tiles including rubbing and

polishing complete including cost of precast tile.)- In First Floor

15.2 Anti skid Ceramic Tiles Flooring :

15.2.1 Fixing 30cm x 30cm / 40cm x 40cm special plain / printed series ceramic floor tiles of

premium grade having thickness 7mm to 8mm confirming to IS 13755 in floors,

treads on steps and landing on 25mm. thick bed of cement mortar 1:1 (1 cement : 1

sand) joined with neat cement slurry mixed with pigment to match the shade of the

tiles including rubbing and polishing complete including cost of precast tile.)- In

Ground Floor SQM 1111.04 550.85 612017.05

Sl. Item Description Unit Rate Quantities Amount

15.2.2 Fixing 30cm x 30cm / 40cm x 40cm special plain / printed series ceramic floor tiles of

premium grade having thickness 7mm to 8mm confirming to IS 13755 in floors,

treads on steps and landing on 25mm. thick bed of cement mortar 1:1 (1 cement : 1

sand) joined with neat cement slurry mixed with pigment to match the shade of the

tiles including rubbing and polishing complete including cost of precast tile.)- In First

15.3 Chequered Tiles Flooring:

15.3.1 Fixing Chequerred precast cement concrete tiles 22 mm thick in floors, treads on steps

and landing on 25mm. thick bed of cement mortar 1:1 (1 cement : 1 sand) joined with

neat cement slurry mixed with pigment to match the shade of the tiles including

rubbing and polishing complete including cost of precast tile.)- In Ground Floor

15.3.2 62mm thick Hardenite Flooring :

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50

mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate

20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2

(1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume,

hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s

specifications. This includes cost of cement slurry, but excluding the cost of nosing of

steps etc. complete.

15.3.3 CC(1:2:4) Flooring Finished with floating coat of neat cement punning.:

2.5 Cm. artificial stone flooring with cement concrete (1:2:4) with washed gravel

including punning. SQM 309.12 379.32 117255.40

15.4 Terrazo / Mosaic Flooring :

40 mm thick marble chips flooring rubbed and polished to granolithic finish, under

layer 34 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 12.5 mm nominal size) and top layer 6mm thick with white, black, chocolate,

grey, yellow or green marble chips of sizes from 1 mm to 4 mm nominal size, laid in

cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion

of 4:7 (4 cement marble powder mix : 7 marble chips) by volume, including cement

slurry etc. complete :

Medium shade pigment with 50% white cement and 50% ordinary cement

15.5 Wall Ceramic Tiles :

15.5.1 Fixing 20cmx30cm / 20cm x 20cm special plain /printed series ceramic wall tiles of

premium grade having thickness 6.5mm to 6.7mm confirming to IS 13753 , in dado,

skirting and rises of steps on 12mm. thick cement plaster 1:3 (1 cement : 3 sand) joined

with neat cement slurry mixed with pigment to match the shade of the tiles including

rubbing and polishing complete including cost of precast tile. . - In Ground Floor.

15.5.2 Fixing 20cmx30cm / 20cm x 20cm special plain /printed series ceramic wall tiles of

premium grade having thickness 6.5mm to 6.7mm confirming to IS 13753 , in dado,

skirting and rises of steps on 12mm. thick cement plaster 1:3 (1 cement : 3 sand) joined

with neat cement slurry mixed with pigment to match the shade of the tiles including

rubbing and polishing complete including cost of precast tile. . - In First Floor.

16 INTERNAL FINISHING WORKS :

16.1 6MM CEMENT PLASTER TO CEILING :

Sl. Item Description Unit Rate Quantities Amount

16.1.1 6 mm thick cement plaster (1:4) to R CC surfaces finished smooth including closed deep

chiping and slury treatment - In Ground Floor SQM 168.98 4681.24 791018.00

16.1.2 6mm thick cement plaster (1:4) to R.C.C. surfacesfinished smooth including closed

deep chipping & slurry treatment. - In First Floor SQM 173.15 3360.89 581945.52

16.1.3 6mm thick cement plaster (1:4) to R.C.C. surfacesfinished smooth including closed

deep chipping & slurry treatment. - In Second Floor SQM 177.52 123.03 21839.40

16.2 12MM CEMENT PLASTER TO INSIDE FACES OF WALLS :

16.2.1 12mm thick Cement Plaster (1:4) over Brick Masonry finished smooth in Inside - In

16.2.2 12mm thick Cement Plaster (1:4) over Brick Masonry finished smooth in Inside - In First

16.2.3 12mm thick Cement Plaster (1:4) over Brick Masonry finished smooth in Inside - In

Second Floor. SQM 171.14 421.54 72140.67

16.3 Providing and applying white cement based putty of average thickness 1 mm, of

approved brand and manufacturer, over the plastered wall surface to prepare the

surface even and smooth complete. SQM 80.64 29745.69 2398692.10

16.4 Applying priming coats with primer of approved brand and manufacture, having low

VOC (Volatile Organic Compound ) content..:

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC

content less than 50 grams/ litre. SQM 41.44 1499.92 62156.56

16.5 Applying priming coats with primer of approved brand and manufacture, having low

VOC (Volatile Organic Compound ) content..:

With water thinnable cement primer on wall surface having VOC content less than 50

16.6 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less

than 50 gms/litre, of approved manufacturer, of required shade and colour complete,

as per manufacturer’s specification.

Two or more coats on new work sqm

16.7 Wall painting with premium acrylic emulsion paint of interior grade, having VOC

(Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and

manufacture, including applying additional coats wherever required to achieve even

shade and colour.

16.8 Painting with synthetic enamel paint having VOC (Volatile Organic Compound )

content less than 50 grams/ litre of approved brand and manufacture to give an even

shade : Two or more coats on new work sqm 82.88 665.00 55115.20

17 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias

and similar locations of required size, approved shade, colour and texture laid over 20

mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white

cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,

moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade Area of slab over 0.50 sqm .

18 Extra for fixing marble /granite stone, over and above corresponding basic item, in

facia and drops of width upto 150 mm with epoxy resin based adhesive, including

cleaning etc. complete. RMT 282.24 306.03 86373.91

19 Extra for providing opening of required size & shape for wash basin/ kitchen sink in

kitchen platform, vanity counter and similar location in marble/ Granite/ stone work,

including necessary holes for pillar taps etc. including moulding, rubbing and polishing

of cut edges etc. complete.

Sl. Item Description Unit Rate Quantities Amount

20 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size

75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of

appropriate width with chase cutter and embedding the stone in the chase with epoxy

grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished

smooth. Granite Stone of approved shade.

21 EXTERNAL FINISHING WORKS ":

21.1 20 MM THICK CEMENT PLASTER TO OUTSIDE FACES OF WALLs

[To prevent surface cracks appearing between junctions of column/beam and walls,

150 mm wide chicken wire mesh should be fixed with U nails 150 mm centre to centre

before plastering the junction. The plastering of walls and beam/column in one vertical

plane should be carried out in one go. For providing and fixing chicken wire mesh with

U nails payment shall be made separately.]

21.1.1 Providing & Applying .20mm thick cement plaster (1:4) (1 cement: 4 coarse sand). - In

Ground Floor. SQM 238.56 3590.34 856511.51

21.1.2 Providing & Applying .20mm thick cement plaster (1:4) (1 cement: 4 coarse sand). - In

21.1.3 Providing & Applying .20mm thick cement plaster (1:4) (1 cement: 4 coarse sand). - In

Second Floor. SQM 256.48 360.61 92489.77

21.2 Supplying 150 mm wide chicken wire mesh of standard quality as available in local

market & fixing with U- nails 150 mm centre to centre before plastering the junction

of walls and beam/column in one vertical plane to prevent surface cracks appearing

between junctions of column/beam and walls before plastering. Payment shall be

made by measuring the chicken mesh area only.

21.3 Finishing walls with water proofing cement paint of approved shade on new work two

coats to give an even shade including the cost of cement paint. - In Ground Floor level.

21.4 Finishing walls with water proofing cement paint of approved shade on new work two

coats to give an even shade including the cost of cement paint. - At First Floor level.

21.5 Finishing walls with water proofing cement paint of approved shade on new work two

coats to give an even shade including the cost of cement paint. - At above First Floor

21.6 Finishing walls with exterior weather coat / weather shield paint of required shade :

Two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm.

22 Drip course mould plaster 1:4 (1:cement :4 sand) including necessary scaffolding curing

etc complete at all depth and height as per direction of site in charge.

23 "2.5 cm thick grading concrete (1:2:4) on roof slab with 6mm size hard granite chips on

new work including cost of labour,material,T&P etc all complete. "

24 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse

sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed

of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted

with fine sand, including necessary excavation, levelling & dressing & finishing the top

Sl. Item Description Unit Rate Quantities Amount

25 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone

aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1

cement : 3 fine sand) as per standard design : In 75x75 mm deep chase metre

26 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over

P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement

: 3 coarse sand) and a coat of neat cement, rounding the edges and making and

finishing the outlet complete.

27 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming

to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10

mm gap for thermal expansion,

(i) Single socketed pipes.: 110 mm diameter RMT. 430.08 840.00 361267.20

28 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for

unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal

28.2 Shoe (Plain)

28.3 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised -

PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S.

screws of required length, including cutting brick work and fixing in cement mortar 1:4

(1 cement : 4 coarse sand) and making good the wall etc. complete.: 110 mm

29 False Ceiling works :

15mm thick calcium silicate false ceiling

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight

calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true

horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel

sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’

runner suitably spaced at joints to get required length and of size 24x38 mm made

from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T”

of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced

between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and

secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick

(Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid

of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle

pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with

the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @

230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of

approved texture in the grid, including, cutting/ making opening for services like

diffusers, grills, light fittings, fixtures, smoke detectors etc.,

Sl. Item Description Unit Rate Quantities Amount

wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted

cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash

fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x

0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24

mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as

per specifications, drawings and as directed by Engineer-in-Charge.

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No

deduction shall be made for exposed frames/ opening (cut outs) having area less than

0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light

reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance

and also having thermal conductivity <0.043 w/ mK.

30 Structural steel work riveted, bolted or welded in built up sections, trusses and framed

work, including cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer all complete.

31 Design, supply, installation complete in all respect of prefabricated tunnel green

houses 42 m x 8 m (336 sqm) growing area and height 2.5 m as per parameters below:

Ridge: 1 x H profile belt / 34 x 32 x 1.5 mm

Laterals: 2 x H profile belts / 34 x 32 x 1.5 mm

Front & auctions: C proflie for zig zag

Enclosure door: 1 front door 2x3 , 2 retractable doors

Front closing: plastic as per manufacturer's specification

Front reinforcement: Galvanizzed square tube/ Sendzimir 275 or equivalent / 50 mm

Arcs: ⌀ 48 x 1.5 mm / distance 2.8 m

Laterals: Anti insect mesh 20 x 10 threads per sqcm/perimeter skirt Raffia cloth

Pillars: Galvanized steel Sendzimir 275 or eqv./ 48 x 1.5 mm

Plastic cover shall be as per manufacturer's specification Necessary construction

drawings and design from manufacturer based on above parameters to be submitted

to EIC for approval. Above cost is inclusive of all materials/ accessories required for

installation. Manufacturer's certification regarding material, design, installation and

quality assurance has to be submitted.

32 Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any

pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I

plain/bitumen washers complete

but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured

out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin

system under approximately 2400 psi and hot cured. They shall be of uniform

pigmentation and thickness without air pockets and shall conform to IS 10192 and IS

12866.The sheets shall be opaque or translucent, clear or pigmented, textured or

smooth as specified. 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down

(2" or 3" or 6" ) as specified .

Sl. Item Description Unit Rate Quantities Amount

33 Supplying and fixing rolling shutters of approved make, made of required size M.S.

laths, interlocked together through their entire length and jointed together at the end

by end locks, mounted on specially designed pipe shaft with brackets, side guides and

arrangements for inside and outside locking with push and pull operation complete,

including the cost of providing and fixing necessary 27.5 cm long wire springs

manufactured from high tensile steel wire of adequate strength conforming to IS: 4454

- part 1 and M.S. top cover of required thickness for rolling shutters.: 80x1.25 mm M.S.

laths with 1.25 mm thick top cover .

34 Concrete Pavers Block

Providing and laying 60mm thick faciory made cement concrete interlocking paver

block of M -30 grade made by block making machine with strong vibratory compaction,

of approved size, design & shape, laid in required colour and pattern over and

including 50mm thick compacted bed of coarse sand, filling the joints with line sand

etc. all complete as per the direction of Engineer-in-charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.)

trusses etc., including cutting, hoisting, fixing in position and applying a priming

coat of approved steel primer, including welding and bolted with special shaped

washers etc. complete.

Hot finished seamless type tubes

36 Providing and fixing precoated galvanised iron profile sheets (size, shape

and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05

%) total coated thickness with zinc coating 120 grams per sqm as per IS: 277,

in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and

polyester top coat 15-18 microns. Sheet should have protective guard film of 25

microns minimum to avoid scratches during transportation and should be

supplied in single length upto 12 metre or as desired by Engineerin-charge. The

sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm)

with EPDM seal, complete upto any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters and trusses and including cutting

to size and shape wherever required.

37 Providing and applying integral crystalline slurry of hydrophilic in nature for

waterproofing treatment to the RCC structures like retaining wall of the

basement, water tanks, roof slabs, podiums, reservoir, sewage& water

treatment plant, tunnels/subway and bridge deck etc. prepared by mixing in the

ratio of 5:2(5 parts integral crystalline slurry :2 parts water ) for vertical surfaces

& 3:1 (3 parts integral crystalline slurry:1 part water) for horizontal surface and

applying the same from negative (internal) side with the help of synthetic fiber

brush Penetron slurry [email protected] kg/Sqmt. for two coat . The material shall

meet the requirements as specified in ACI-212-3R-2010 i.e by reducing

permeability of concrete by more than 90% compared with control concrete as

per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The

crystalline slurry shall be capable of self-healing of cracks upto a width of

0.50mm. The work shall be carried out all complete as per specification and the

direction of the engineer-in-charge. The product performance shall carry

guarantee for 10 years against any leakage.

For all surface.

Sl. Item Description Unit Rate Quantities Amount

38 Providing and fixing Glass Reinforced Concrete (G.R.C) Screens/Jali in approved size,

pattern, design, thickness and color including MS framing duly painted with corrosion

resitant paint / rust proof paint complete with sealant and complete with all necessary

accessories. Necessary fabrication drawings including fixing details of Jali to be

submitted for approval prior to execution.

Border Thickness: min. 50mm : Internal Membrane: min. 30mm

39 Providing and applying pattern painting, replicating Indian traditional embroidery art,

with texture paints composed of high-quality durable acrylic modified resin, UV

resistant and designed with anti-algal and anti-fungal properties, of approved

manufacturer, over a coat of suitable under coat primer, to the external walls upto

floor-V level as per approved design/Drawing .

40 POINTING ON BRICK WORK :

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine

sand): Flush / Ruled/ Struck or weathered pointing SQM 184.80 3221.78 595384.02

TOTAL OF CIVIL WORKS : Rs 175583933.28

B. INTERNAL P.H Work:-

1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes conforming to

IS:15778,having thermal stability for hot & cold water supply, including all CPVC plain

& brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings with one step CPVC solvent cement and testing of

joints complete as per direction of Engineer-in-Charge. Concealed work, including

cutting chases and making good the walls etc

1.1 a) 32 mm nominal outer dia Pipes Mtr 1442.54 1062.00 1531974.93

2 Cutting holes through existing brick work including making good the same in cement

mortar (1:4) for taking GI/PVC pipes and fittings etc all complete as per specification.

3 Cutting grooves in pucca floors and walls for taking GI/PVC pipes and making good the

damages as per specification complete.

3.1 a) Detail cost per 1 meter Mtr 81.76 2092.00 171041.92

4 Providing and fixing on wall face unplasticised Rigid PVC soil,waste and rain water

pipes confirming to IS:13592 Type A(single socket pipes) & on wall face unplasticised-

PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :

5382, leaving 10 mm gap for thermal expansion .

4.1 110 mm dia SWR pipes (UPVC) MTR 685.44 653.00 447592.32

4.2 110 mm dia single junction with door NOS 598.61 102.00 61058.71

4.4 110 mm dia bend with door NOS 341.58 102.00 34840.92

5 Fixing 110mm size ‘P’ or ‘S’ trap (UPVC fittings conforming to IS 14735:1999) for water

closet squatting pan including jointing the trap with pan as per specification of the

manufacturer of fittings.

6 110mm dia floor trap (IN-LET OUT-LET Type) NOS 191.46 87.00 16657.32

Sl. Item Description Unit Rate Quantities Amount

8 Supply & Fixing water closet,squatting pan (Orrisa type W.C pan) conforming to IS

2556:part3-2004;( With PVC Low down Cistern of approved make) duly embedded in

cement concrete (1:4:8) using hard granite metal 4cm nominal size all complete as per

(White Glazed vitreous china Squatting Pan-Long pattern size 580mm.) NOS 5684.51 19.00 108005.68

9 Supply & Fixing Wash Down Water Closet (European type W.C pan) with integral ‘S’ or

‘P’ trap conforming to IS 2556 : Part 8-2004, to the floor with wooden plug and

chromium plated screws including jointing the trap with soil pipe in cement mortar

(1:1) etc all complete as per specification. ( With PVC Seat & cover and PVC Low down

Cistern of approved make) (White Vitreous china wash down water closet E.W.C)

10 Supply & Fixing wash basins with hole for pillar taps conforming to IS 2556 : Part 4-

2004, of approved make, with Cast Iron or M S brackets painted white including

cutting holes in walls and making good the damages etc all complete as per

a)Vitreous china flat back wash basin 550mmX400mm NOS 2873.19 68.00 195377.06

11 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350

mm of approved make with spreaders with unions and clamps (all in C.P. brass) with

waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P.

brass, including painting of fittings and cutting and making good the walls and floors

wherever required :

12 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983, of

approved make. with C.I. brackets and stainless steel plug 40 mm, including painting of

fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board, 510x1040 mm bowl depth 250 mm

13 Providing and fixing P.V.C. low level flushing cistern with manually controlled device

(handle lever) conforming to IS : 7231, with all fittings and fixtures complete. (10 Litre

14 Providing and fixing gun metal gate valve with C.I. wheel of ISI approved quality

(screwed end) :

15 Supply & Fixing of Brass Screw-down Bib Cocks (Taps) with flange , polished bright

conforming to IS:781-1995, of approved make of the following nominal sizes as per

specification complete. (Delux Head& high quality.

15.1 a)15mm dia CP brass bib cock (Short body ) with flange NOS 1263.83 73.00 92259.62

15.2 b)15mm dia CP brass bib cock (Long body ) with flange NOS 1383.39 15.00 20750.86

16 Supply & Fixing of Brass Screw-down Stop Cocks conforming to IS:781-1995 of the

following nominal sizes as per specification complete. (Deluxe Head& high quality)

16.1 a)15mm dia CP brass Angle Stop cock NOS 939.33 69.00 64813.96

16.2 b)15mm dia CP brass concealed Stop cock NOS 1178.45 124.00 146128.15

17 Supply & Fitting & fixing of following bathroom fixtures including all cost ,material

17.1 a) Supply & Fix Chromium Plated Brass Revolting Shower rose with Arm of 15mm or

20mm inlet including polishing all complete as per specification.(Deluxe Head &Heavy

17.2 b)Supplying, Fitting & fixing health faucet of approved make with one metre long

Tube, Hook & all fixtures. NOS 2339.80 61.00 142728.00

Sl. Item Description Unit Rate Quantities Amount

17.3 c)Supply & fixing Fixing Chromium Plated brass soap dish complete with Chromium

Plated brass brackets fixed to P.V.C plugs with Chromium Plated brass screws as per

specification. (125mm ). NOS 777.08 66.00 51287.54

17.4 d)Supplying & Fixing standard sized glass-shelf with Chromium Plated brass brackets

and guard rails complete, fixed to woden plugs with Chromium Plated brass screws &

Fixing of standard chromium plated shelf with all fixtures as per specification.

i) Glass shelf with C.P brass brackets and guard rails fixed to wooden plugs of size

600mm × 120mm with all fixtures .

17.5 e)Supply & Fixing standard sized Chromium Plated brass towel rail & towel ring

complete with Chromium Plated brass brackets fixed to wooden plugs with Chromium

Plated brass screws, complete as per specification.

17.5.1 i)25mmX600mm long C.P towel rail (Heavy Quality) of approved make NOS 2387.63 31.00 74016.44

17.5.2 ii)C.P. towel ring (Heavy Quality) of approved make NOS 1050.34 31.00 32560.59

17.6 f)Supplying & Fixing 600mm x 450mm x 6mm thick mirror of superior glass with frame

of approved make and fixed to wall with wooden plugs & chromium plated brass

screws and washers complete as per manufacturer specification. (Heavy Quality)

18 Supplying & Laying in trenches unplasticised UPVC pipes conforming to IS:13592-2013

and specials of the following outside diameter for all classes including jointing with

supply of approved solvent cement by non-heat application method including testing

as per specification complete. (Earth work in trenches to be measured and paid for

18.1 a)160mm dia rigid UPVC pipe class-3 (0.60mpa) MTR 1589.67 276.00 438748.98

19 Construction of inspection chamber

Constructing brick masonry manhole in cement mortar 1:6 ( 1 cement : 6 coarse sand )

with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded

stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4

coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm

thick with cement mortar 1:4 (1 cement : 4 coarse sand) finished with floating coat of

neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand :

4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat

cement complete as per standard design :

Inside size 90x90 cm and 45 cm deep including C.I. cover with frame (light duty)

455x610 mm internal dimensions, total weight of cover and frame to be not less than

38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With Fly ash bricks of 25 Cm. x 12 Cm. x 8 Cm. size having crushing strength not less

than 75 Kg./Cm2

20 Supplying & Fixing rotational moulded polythylene cylindrical vertical water storage

tanks confirming to IS:12701-1996 including cutting holes through the tanks and fixing

mild steel tubes and fittings and providing extra sockets and jam nuts,fixing ball valv

etc,including hoisting up to ageight of 5m above ground level and placing the tank to

the required position etc all complete as per specification and direction of E.I.C

Sl. Item Description Unit Rate Quantities Amount

20.1 2000 ltr capacity double layer cylindrical vertical water storage tanks details of cost for

one tank on the roof of ground floor) NOS 13044.96 31.00 404393.91

21 Supplying, Testing, Commissioning,Fitting of Horizontal type centrifugal Pump with

electrically operated 1.0 HP motor for drawing water from underground water

reservoir to overhead Tanks installed over the Roof.

Total of Internal PHE 7682911.14

TOTAL of CIVIL AND PHE = 183266844.42

EXTERNAL DEVELOPMENT WORKS , i.e.,

(A) EXTERNAL PLUMBING WORKS, (B) HORTICULTURAL WORKS, (C) RAIN WATER HARVESTING & BORE WELL

WORKS, (D) DISMANTLING OF EXISTING STRUCTURES., (E ) INTERNAL BITUMINIOUS ROAD. etc.

Item Breif Description of works Unit Qty Rate Amount

A EXTERNAL PLUMBING WORKS

1.0 Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA)

conforming to IS - 1536 :

2.0 Providing lead caulked joints to spun iron or C.I. pipes and specials,

including testing of joints but excluding the cost of pig lead : 100 mm

diameter pipe. Each 99.00 224.00 22176.00

3.0 Supplying pig lead at site of work. quintal 2.00 29034.10 58068.19

4.0 Excavating trenches of required width for pipes, cables, etc, including

excavation for sockets, depth upto 1.5 m, including getting out the

excavated materials, returning the soil as required in layers not exceeding

20 cm in depth, including consolidating each deposited layers by ramming,

watering etc.stacking serviceable material for measurements and disposal of

unserviceable material as directed, within a lead of 50 m :

Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

5.0 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts,

rubber insertions etc. (the tail pieces if required will be paid separately) :

6.0 Constructing masonry Chamber 120x120x100 cm inside, in brick work in

cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.

surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm

deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c

necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand :

10 graded stone aggregate 40 mm nominal size) and inside plastering with

cement mortar 1:3 (1 cement

: 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement

complete as per standard design :With common burnt clay F.P.S.(non

modular) bricks of class designation 7.5 each Each 4.00 28052.39 112209.57

7.0 Constructing masonry Chamber 90x90x100 cm inside, in brick work in

cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,with C.I.

surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm

deep (inside) with chained lid and RCC top slab 1:2:4mix (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c

necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand :

10 graded stone aggregate 40 mm nominal size ) and inside plastering with

cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a

floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

8.0 Providing and laying S&S C.I. standard specials such as tees, bends,

collars, tapers, caps, tail piece etc. (Heavy class): Up to 300 mm dia Quintal 25.00 9244.48 231112.00

Total for EXTERNAL PLUMBING WORKS (A) 1512778.08

B HORTICULTURAL WORKS

Item Breif Description of works Unit Qty Rate Amount

1 Trenching in ordinary soil up to a depth of 60 cm including removal and

stacking of serviceable materials and then disposing of surplus soil, by

spreading and neatly levelling within a lead of 50 m and making up the

trenched area to proper levels by filling with earth or earth mixed with

sludge or / and manure before and after flooding trench with water

(excluding cost of imported earth, sludge or manure).

2 Supplying and stacking of good earth at site including royalty and carriage

upto 5 km lead complete (earth measured in stacks will be reduced by 20%

3 Supplying and stacking sludge at site including royalty and carriage upto 5

km lead complete (sludge measured in stacks will be reduced by 8% for

4 Supplying and stacking at site dump manure from approved source,

including carriage upto 5 km lead complete (manure measured in stacks

will be reduced by 8% for payment) :

4.1 Screened through sieve of I.S. designation 20 mm Cum 50.00 257.60 12880.00

4.2 Screened through sieve of I.S. designation 16 mm Cum 50.00 296.80 14840.00

4.3 Screened through sieve of I.S. designation 4.75 mm Cum 50.00 324.80 16240.00

5 Rough dressing the trenched ground including breaking clods. Sqm 500.00 1.68 840.00

6 Uprooting weeds from the trenched area after 10 to 15 days of its flooding

with water including disposal of uprooted vegetation. Sqm 500.00 5.04 2520.00

7 Fine dressing of the ground. Sqm 500.00 3.92 1960.00

8 Spreading of sludge, dump manure and/or good earth in required

thickness as per direction of officer-in-charge (cost of sludge, dump

manure and/ or good earth to be paid separately). Cum 300.00 52.08 15624.00

9 Mixing earth and sludge or manure in the required roportion specified or

directed by the Officer-in-charge Cum 300.00 36.40 10920.00

10 Grassing with selection No. 1/ Doob grass including watering and

maintenance of the lawn for 30 days or more till the grass forms a thick

lawn, free from weeds and fit for mowing including supplying good earth,

if needed (the grass and good earth shall be paid for separately).

10.1 In rows 5 cm apart in both directions. Sqm 1000.00 17.92 17920.00

10.2 With grass Turf . Sqm 1000.00 13.44 13440.00

11 Renovating lawns including weeding, cheeling the grass, forking the

ground, top dressing with sludge or manure, mixing the same with forked

soil, watering and maintaining the lawn for 30 days or more till the grass

forms a thick lawn free from weeds and fit for mowing and disposal of

rubbish as directed, including supplying good earth if needed but excluding

the cost of sludge or manure (the good earth shall be paid for separately).

Item Breif Description of works Unit Qty Rate Amount

12 Half brick circular tree guard in bricks, internal diameter 1.25 metre and

height 1.2 metre above ground and 0.20 m below ground, bottom two

courses laid dry and top three courses in cement mortar 1:6 (1 cement : 6

fine sand) and the intermediate courses being in dry honey comb masonry

per design complete:

With common burnt clay F.P.S. (non modular) bricks of class designation

12.1 Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high,

above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3

mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron

rings in two halves, fixing together at site with required six numbers of 8

mm dia and 30 mm long bolts, including painting two coats with synthetic

enamel paint of approved brand and manufacture over a coat of primer.

One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be

welded to the tree guard near the middle height and lettered CPWD /

approved name. The tree guard shall be suitably fixed to the ground by

embedding four legs of tree guard in pits of suitable dia and to a depth of

25 cm, refilling the pits with soil and ramming, complete in all respect as

per satisfaction and direction of Officer-in-charge. Each 50.00 4592.00 229600.00

13 Making tree guard 53 cm dia and 1.3 m high as per design from empty coal

tar drums, supplied free by the department, including providing and fixing

2 nos M.S. sheet rings 50 x 0.5 mm fixed with rivets complete in all

respects including painting inside and outside of tree guard with:

Two or more coats of synthetic enamel paint of approved quality shade

over a priming coat.

14 Edging with bricks laid dry length wise, including required excavation,

refilling, consolidating with hand packing and spreading surplus earth

neatly within a lead of 50 m :

With Common burnt clay F.P.S (non modular) bricks of Class

designation 7.5 . Metre 1000.00 56.00 56000.00

15 Providing Circular Cement Concrete pots of specified size, cast with

cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded

stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos

horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per

design, including required form work, finishing with cement punning on

exposed surface, curing for specified period and stacking in required rows

& height, all complete as per direction of Officer-in-charge.

15.1 Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall

thickness of 25.4 mm Each 200.00 246.40 49280.00

15.2 Top inside dia 30 cm, outer bottom dia 20 cm, total height 30 cm with wall

thickness of 25.4 mm Each 200.00 179.20 35840.00

16 Supplying laying 60mm Pavers Blocks including the cost of sand packing &

PCC(1:4:8) below sand filling, in Pathways. Sqm 500.00 952.00 476000.00

Total for HORTICULTURAL WORKS (B) 1369984.00

Item Breif Description of works Unit Qty Rate Amount

C Sinking of Bore well :

Transportation to site of tube well/ Bore well, all boring

equipments,machinaries, tools etc with all accessories, including erection of

1.0 equipments for drilling of bore well, lowering of casing pipes and dismantling

/ removal charges of all equipments and transporting back from the site to

the place of delivery after completion of work. Job 2.00 6272.00 12544.00

Labour charges for drilling / boring of upto 400mm diameter with reverse-

circulation method by means of mechanically driven rotary-drilling system

through any type of soil for sinking / lowering the tube well with 200mm dia

PVC pipe for top enlargement ( up to 40.0metre depth). The quoted rate

should include the hire charges and labour for supplying & lowering of

2.0 suitable diameter casing pipes upto full depth of tubewell, drill-bits, drill pipes

and lowering of tube well assembly including necessary sockets,tools &

plants,staging and making necessary arrangement for boring ,force pumping

set and making arrangement for water required for boring etc, withdrawing

of casing pipes / drill bits etc complete and lowering of pipes, strainers, blank

pipe etc. complete.

2.1 a) From Ground level to 50 mtrs below Ground level.. Mtr 100.00 1756.16 175616.00

2.2 b) From 50 mtrs below GL to 100 mtrs below GL.. Mtr 100.00 1930.45 193045.44

2.3 c) From 100 mtrs below GL to 180 mtrs below GL.. Mtr 160.00 2268.58 362973.18

Providing & laying in position heavy duty PVC water pipe of approved make

conforming ti IS 13592 of SWR quality upto 10kg/sqcm pressure rated, for

permanant casing pipes of bore well to be laid upto 135 meters including all

fittings & fixtures and laid in proper line,level & alignment below ground level.

Providing & laying in position 200mm dia heavy duty PVC rigid pipe "of

3.1 equivalent IS approved make, (ASTM-D-1785, SCHEDULE-80) with heavy

duty GI sockets. Rmtr 80.0 1424.75 113980.16

Providing & laying in position 100mm dia heavy duty PVC rigid pipe (ASTM-

D-1785, SCHEDULE-80) with heavy duty GI sockets. Rmtr 200 1066.24 213248.00

Providing & laying in position100mm dia equivalent IS approved make,

heavy duty PVC ribbed ,Tube well STRAINER, conforming to relevant IS

codes, jointing with 100mm dia. PVC bore well / casing pipe with heavy duty

GI sockets of approved quality. Rmtr 60.00 1317.12 79027.20

Providing & Fixing of following heavy duty PVC / M.S. fittings & fixtures

conforming to relevant IS codes, as described below. :-

5.1 200 mm X 100 dia mm heavy duty PVC reducing socket. No 2.00 564.48 1128.96

5.2 200 mm dia M.S. housing clamps with necessary nut-bolts arrangements. Set 2.00 940.80 1881.60

5.3 200 mm dia heavy duty M.S. Top cap. No 2.00 1191.68 2383.36

100 mm dia heavy duty ( 5 to 6mm thick) M.S. ( C-shaped with minimum

50mm high vertical internally threaded face ) bottom cap. 1630.72

5.6 200mm DIA. x 1' ft long PVC nipple. No 2.00 501.76 1003.52

Providing, laying & filling in layers uniformly grained gravel of size 6mm &

below, surrounding the annular space between the bore well hole and

tappering casing pipe upto a depth of 135 meters or as per site requirement

below ground level including transportation, delivery of material and labour

6.0 for filling up of annular space in layers.

[Mode of Measurement : The gravels will be measured in Cum. Contractor

shall provide stacks of gravel in required size which will be measured to a

nearest centimeter and volume comprising of length x breadth x height,

less 5% (five percent) for voids shall be measured and paid for.

Item Breif Description of works Unit Qty Rate Amount

Surging, Washing and cleaning, rinsing the drilled tube well / borewell by

using desired capacity air compressor with allied accessories for 8 hours a

day including making arrangement for showing yield test at the tube well by

V- notch arrangement.

Mode of Measurement: The log book entries will have to be maintained for

actual hours of using of compressor per day and the payment will be made

by considering a day with minimum 8 ( eight) hours of operation or will be

paid proportionately on the nos. of effective operational hours. Day 6.00 9408.00 56448.00

Carrying out Geophysical investigation of the aquifer by electro logging

8.0 system with all tools and plants as necessary to ascertain the availability /

good yield of water including providing of necessary report. Job 2.00 10035.20 20070.40

Collection of water sample for physical, chemical analysis and

bacteriological analysis by carrying out requisite test from reputed / Govt.

9.0 laboratories /Govt. Engineering collages for potablity of water including for

submission of test report all as directed by the Engineer-in-charge etc

Providing & installing in position three phase 7.5 HP submersible pump

motor set of approved make conforming to relevant IS codes with 50 mtrs.

long 3X6.0 sq.mm. copper cable flat finolex or equivalent approved make

conforming to relevant IS code including providing & fixing control panel ,

starter of approved make including Ammeter, Voltmeter & 32 Amp. SP MCB

including fixing on wall by suitable arrangement all as per direction of EIC

Total for Two nos. Borewell [C-2] 1512328.38

Item Breif Description of works Unit Qty Rate Amount

D DISMANTLING OF EXISTING STRUCTURES.

Non-Schedule Item For Dismantling works :

1 Carefully Dismantling of existing old abandoned single storied & two

storied Building along with the existing Boundary wall by dismantling

manually / mechanically existing Brick walls including from foundations,

RCC Columns including its footings, Beams, Roofing etc., Cutting of

reinforcement including removal of all debris outside the premises and to

vacate the land. All the vacated foundations after removal of Bricks,

Concrete etc, to be filled up by supplying, filling with river sand duly

compacted by watering, ramming all complete. Approximate land area for

dismantling of existing abonded structures is 3000 Sqm. Tenderer may like

to visit the site before quoting.

Total for dismantling works 134400.00

E INTERNAL BITUMINIOUS ROAD

1 Earth work excavation in hard soil or gravelly soil within 50m. Intial lead and

1.5 m. intial lift including rough dressing and breaking clods to maximum

5cm. To 7cm and laying and layers not exceeding 0.3m in depth and as per

direction of the department. CUM 1645.31 172.48 283783.07

2 Supplying, spreading and compacting Sand to required thickness, in layers

not exceeding 150 mm to proper gradient and camber, inundating each layer

by water and packing and ramming layer by layer to achieve desired

compaction, including lighting, guarding, barricading and making adequate

earthen bundh where necessary, curing with water as per direction, mending

cracks and depressions by ramming wherever necessary. (The payment is

to be made on the basis of the finished compacted volume.)

3 Construction of embankment with approved material obtained from borrow

pits with all lifts and leads, transporting to site by mechanical means within a

lead of 5kms, spreading, grading to required slope and compactingto meet

requirement of table 300-2 & Clause 305 of MoSRT&H Specifications for

Road & Bridge works (4th Revision) CUM 351.00 410.12 143952.68

4 Construction of granular sub-base by providing Close graded Granular sub-

base Grading-III material as per table 400-1, spreading in uniform layers

with motor grader on prepared surface, mixing by mix in place method with

rotavator at OMC, and compacting with vibratory roller to achieve the

desired density complete as per Clause 401 of MoSRT&H Specifications for

Road & Bridge works (4th Revision). SQM 263.25 2486.40 654544.80

5 Providing, laying, spreading and compacting stone aggregates of specific

sizes to water bound macadam specification including spreading in uniform

thickness, hand packing, rolling with 3 wheeled steel roller 8-10 tonnes in

stages to proper grade and camber, applying and brooming requisite type of

screening/binding materials to fill up the interstices of coarse aggregate,

watering and compacting to the required density as per Clause 404 of

MoSRT&H Specifications for Road & Bridge works (4th Revision). Grading-

Using Type-B 11.2mm stone screenings. Cum. 526.50 3687.04 1941226.56

6 Providing and applying tack coat with bitumen emulsion using emulsion

pressure distributor at the rate of 0.20 kg per sqm on the prepared

bituminous/granular surface cleaned with mechanical broom as per Clause

503 of MoSRT&H Specifications for Road & Bridge works (4th Revision) On

Item Breif Description of works Unit Qty Rate Amount

7 2.5 cm premix carpet surfacing with 2.25 cum and 1.12 cum of stone

chippings of 13.2 mm and 11.2 mm size respectively per 100 sqm and 52 kg

and 56 kg of hot bitumen per cum of stone chippings of 13.2 mm and 11.2

mm size respectively, including a tack coat with hot straight run bitumen,

including consolidation with road roller of 6 to 9 tonne capacity etc. complete

(tack coat to be paid for separately).

With paving Asphalt grade VG - 10 heated and then mixed with solvent at

the rate of 70 grams per kg of asphalt Sqm 2632.50 246.40 648648.00

8 Providing and laying seal coat sealing the voids in a bituminous surface laid

to the specified levels, grade and cross fall using Type-A seal coat with

0.09cum of 6.7mm size chips and 9.80kg. of 60/70 penetration grade of

bitumen for 10sqm as per Clause No. 513 of MoSRT&H specifications for

Road & Bridge works (4th Revision) Sqm 2632.50 97.44 256510.80

9 Providing, laying and making kerb channel 30 cm wide and 50 mm

thick with cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone

aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40 mm

nominal size, well rammed and consolidated and grouted with fine sand,

including finishing the top smooth etc. complete and as per direction of

Engineer-in-charge. Sqm 351.00 480.48 168648.48

10 Providing and laying at or near ground level factory made kerb stone of M-

25 grade cement concrete in position to the required line, level and

curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand),

including making joints with or without grooves (thickness of joints except at

sharp curve shall not to more than 5mm), including making drainage

opening wherever required complete etc. as per direction of Engineer-in-

charge (length of finished kerb edging shall be measured for payment).

(Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Total of E 4895613.35

Total for A+B+C+D+E= 9425103.81

Description Unit Quantity Rate Amount

1.0 Earth work excavation in hard soil or gravelly soil within 50m. Intial

lead and 1.5 m. intial lift including rough dressing and breaking clods

to maximum 5cm. To 7cm and laying and layers not exceeding 0.3m

in depth and as per direction of the department. Cum. 1441.250 172.48 248586.80

2.0 Filling in foundation and plinth with excavated materials, moorum

including watering and ramming as directed by the Engineer-in-

3.0 Providing and Laying plain cement concrete 1: 4: 8 .( 1 cement : 4

sand : 8 stone Aggregate 40mm nominal size ) As levelling course

in foundation and plinth etc. complete all depth and height.

REINFORCED CEMENT CONCRETE WORK

4.0 Providing and Laying reinforce cement concrete M-25Grade, 20 mm

nominal size HBG chips including cost all

materials,labours,T&P,curing etc complete (excluding the cost of

reinforcement) and direction of Engineer-in-charge.

In Ground Floor including Foundation :

(i) For R.C.C. work in 1st floor or any additional floor add 15 per cent

extra labour over and above the rate of next lower floor for lifting of

(v) For R.C.C. and reinforcement works below ground level beyond

1.5m and upto 4.5m depth add 15 per cent extra labour over and

above the rates of the respective items for lowering the materials.

5.0 Centering & Shuttering works :

(i) For centering and shuttering for R.C.C. work (in floor and roof slab,

Landings, Balconies, projecting sunshades, Chajja, Stairs Plinth

band,footings , base of columns, precast slab, beams and columns,

Lintels,R.C.C. Walls and Fins) in first floor and subsequent upper

floors add 20 percent extra to the rate of respective centering and

shuttering items over and above the rates from the next lower floor.

5.1 Rigid and smooth centering and shuttering for R.C.C. works including

false work and dismantling them after casting including cost of

materials complete in ground floor.:

R.C.C. foundation and plinth band, footings, bases of columns, mass

concrete, precast slabs etc. Sqm. 5056.000 113.01 571368.45

5.2 Rigid and smooth centering and shuttering for R.C.C. works including

false work and dismantling them after casting including cost of

materials complete in ground floor.:

(i) R.C.C. Floor roof slabs, landings, balconies, projecting sun-shades

and chajjas upto 4.3m.height. Sqm. 70.000 473.97 33178.10

6.0 Reinforcement works :.

Supplying ,fitting and placing uncoated HYSD bar reinforcement

complete as per drawing and technical specification.

In Ground Floor Qtl. 520.157 9065.34 4715402.10

Description Unit Quantity Rate Amount

Supplying , Laying Single Brick Flat soling below Foundations , Flooring etc.,

7.0 using Clay burnt bricks , including filling gaps with fine sand.

8.0 PLASTERING & POINTING WORK

20 mm cement plaster of mix :

9.0 Neat cement punning Sqm. 3111.000 70.28 218641.08

10.0 Steel work welded in built up sections/ framed work, including cutting,

hoisting, fixing in position and applying a priming coat of approved

steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates

and similar works Kg 14400.000 114.24 1645056.00

11.0 P/L non-pressure NP2 class (light duty) R.C.C. pipes...jointed with

stiff mixture of CM in the proportion of 1:2 -complete

BOUNDARY WALL AND GATE

EXTERNAL DEVELOPMENT - BOUNDARY WALL

Description Unit Quantity Rate Amount

Earth work excavation in hard soil or gravelly soil within

50m. Intial lead and 1.5 m. intial lift including rough dressing

1.0 and breaking clods to maximum 5cm. To 7cm and laying

and layers not exceeding 0.3m in depth and as per direction

of the department.

1.1 In hard soil or gravelly soil Cum. 748.62 172.48 129121.98

Filling in foundation and plinth with excavated materials

2.0 including watering and ramming as directed by the Engineer- Cum. 421.63 114.99 48483.40

Plain Cement Concrete works :

Providing and Laying plain cement concrete 1: 4: 8 .( 1

cement : 4 sand : 8 stone Aggregate 40mm nominal size )

As levelling course in foundation and plinth etc. complete

all depth and height.

REINFORCED CEMENT CONCRETE WORK

Providing and Laying reinforce cement concrete M-25Grade,

20 mm nominal size HBG chips including cost all

materials,labours,T&P,curing etc complete (excluding the

cost of reinforcement) and direction of Engineer-in-charge.

In Ground Floor including Foundation :

5.0 (i) For R.C.C. work in 1st floor or any additional floor add 15

per cent extra labour over and above the rate of next lower

floor for lifting of concrete etc..

(v) For R.C.C. and reinforcement works below ground level

beyond 1.5m and upto 4.5m depth add 15 per cent extra

labour over and above the rates of the respective items for

lowering the materials.

5.1 In Ground Floor including Foundation : Cum. 374.69 5763.52 2159533.31

Description Unit Quantity Rate Amount

Centering & Shuttering works :

(i) For centering and shuttering for R.C.C. work (in floor and

6.0 Landings, Balconies, projecting sunshades, Chajja, Stairs

Plinth band,footings , base of columns, precast slab, beams

and columns, Lintels,R.C.C. Walls and Fins) in first floor and

subsequent upper floors add 20 percent extra to the rate of

respective centering and shuttering items over and above

the rates from the next lower floor.

Rigid and smooth centering and shuttering for R.C.C. works

including false work and dismantling them after casting

6.1 including cost of materials complete in ground floor.: Sqm. 1834.07 113.01 207264.58

R.C.C. foundation and plinth band, footings, bases of

columns, mass concrete, precast slabs etc.

Rigid and smooth centering and shuttering for R.C.C. works

including false work and dismantling them after casting

including cost of materials complete in ground floor.:

R.C.C. beams, columns, girders and bressmers etc.

Reinforcement works :

7.0 For Reinforcement work in 1st floor or any additional floor

add 5 per cent extra labour over and above the rate of next

Supplying ,fitting and placing uncoated HYSD bar

reinforcement complete as per drawing and technical

In Ground Floor

MASONRY BRICK WORK WITH 25CM. BRICKS :

(i) For brick masonry in superstructure add extra towards

extra labour for scaffolding to the rate in foundation and

plinth. ------- 1 cum 33.00

(ii) For brick masonry in item for 1st floor and subsequent

higher floors add 15 percent extra labour over and above the

rates of next lower floor.

Description Unit Quantity Rate Amount

Brick work with Fly ash bricks of 25 Cm. x 12 Cm. x 8 Cm.

size having crushing strength not less than 75 Kg./Cm2 with

dimensional tolerance ± 2 % in cement mortar (1:6) in

foundation and plinth.

Half brick masonry with non modular fly ash bricks of class

designation 75, conformingio IS :12894, in super structure

8.2 above plinth and upto floor V level. Sqm 1689.00 712.32 1203108.48

Cement mortar 1 : 4 (1 cement : 4 coarse sand)

8.3 Supplying , Laying Single Brick Flat soling below Foundations ,

Flooring etc., using Clay burnt bricks , including filling gaps with

Description Unit Quantity Rate Amount

Steel work welded in built up sections/ framed work,

including cutting, hoisting, fixing in position and applying a

priming coat of approved steel primer using structural steel

etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets,

gates and similar works

PLASTERING & POINTING WORK

10.0 Cement Plaster (In Coarse Sand)

Providing & Applying .20mm thick cement plaster (1:4) (1

cement: 4 coarse sand)

Finishing walls with water proofing cement paint of approved

11.0 shade on new work two coats to give an even shade sqm 4501.46 38.08 171415.60

including the cost of cement paint. - In Ground Floor level.

12.0 Applying priming coat :

Applying priming coats with primer of approved brand and

manufacture, having low VOC (Volatile Organic Compound )

With ready mixed pink or grey primer on wood work (hard

and soft wood) having VOC content less than 50 grams/

Painting with synthetic enamel paint of approved brand and

manufacture to give an even shade :

13.1 Two or more coats on new work sqm 308.00 82.88 25527.04

NON SCHEDULE ITEMS

Description Unit Quantity Rate Amount

1 SITC of 1000 Kg passenger cum goods lift with machine roomless

Number Of Lifts/Type Of Lift: One Goods Lift

Load / Speed : 1.0 Ton / 1.00 Mtr. Per Second

Drive : MICRO PROCESSOR BASED ACVF - CLOSED LOOP

Travel / PIT / HeadRoom : 4.5 METER / HeadRoom 4500mm

Number Of Floors : 2 (G + 1 UPPER FLOORS)

Number Of Landing Entrances :2 (G + 1 UPPER FLOORS)

Number and Position of Car Entrances : 1 (ONE), IN FRONT ONLY

Position Of Machinery : Machine Room

Size of Lift Well : 2500 mm Width x 2500 mm Depth

Lift Car Inside Size : AS PER NBC 2016

Type or Design of Lift Car Stainless Steel - Hairline Finish -

Car Ceiling - Car Floor : Sleek (Medium Circular Lights) - Ss Hairline Finish

Car Fittings : Bbs 170 Led Light & Axial Flow Fan

Type Of Landing Entrance Protection : Centre Opening Sliding Door - Stainless Steel -

Hairline Finish

Type Of Car Entrance Protection : Power Operated Centre Opening Sliding Door -

Stainless Steel - Hairline Finish

Type Of Landing Frame : Stainless Steel - Hairline Finish

Clear opening of Gates / Doors : 900 X 2000 (MM Wide * MM Height)

Type Of Control: Single car control System Microprocessor Based Full Collective

Control With / Without Attendant

Electric Supply : AC 415 VOLTS, 3 PHASE, 50 CYCLES +10% - 20%

Elevator pit depth : 1650 mm

Signals : All indicator display will be LED

Special features :

1. Automatic Rescue Device with UPS back-up.

2. Battery operated Emergency Light and Alarm.

3. Fireman’s Emergency Operation.

4. Anti-Nuisance Car Call Cancellation.

5. Car Call Cancellation at Terminal Stop.

6. Automatic Operation for Car Light And Fan.

7. Close loop control for main and door drive.

8. Repeated Door Closing in Case Of Lock contact Failure.

9. Voice Announcement System.

10. Over Load Indicator.

11. Phase Failure & phase Reversal Protection.

12. Self-Detection & Indication of Faults.

13. Door System by Light Curtain (81Beam).

14. Car arrival chime

15. Home Landing.

16. VF Door Drive System.

17. Decorative call buttons

18. Braille System

19. Intercom system

20. Necessary fittings for the physically handicapped

21. Traction media will be coated steel belt

NOTE: Contractor should inspect the Site before submitting the offer

All design car size to be in compliance to relevant IS code.

Cost should include following :

i) Builders work, and scaffolding, pit ladder etc.

ii) Cost for providing landing door sills

iii) Cost of structurals to match shaft dimension, if any.

iv) Arrangement for power to cater the demand of constructional load, testing

and commissioning of the lift.

v) Lift pit / shaft lighting.

vi) Landing door frame for landing gate

vii) Unloading at site Nos 1 2032033.81 2032033.81

4 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable in surface / recessed steel conduit,

with piano type switch, phenolic laminated sheet, suitable size MS box and earthing

the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.

5 Providing and fixing following capacity TP&N disconnector fuse switch unit inside the

existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel,

making connections, etc. as required

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV

grade of following size in the existing masonary open duct as required.

7 Supplying and making end termination with brass compression gland and aluminium lugs for

following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV

grade as required.

ELECTRICAL SUMMARY

SL.No DESCRIPTION AMOUNT In Rs.

1 SCHEDULED ITEM 7746347.50

2 LOW SIDE ELECTRICAL WORKS (NON-SCHEDULED ITEM) 23602516.52

3 ELECTRICAL HV INSTALLATION WORK (NON-SCHEDULED ITEM) 7073792.28

TOTAL PRIME COST 38422656.30

ELECTRICAL WORK (SCHEDULED ITEM)

Sl. Description Unit Qty. Rate Amount

A. CIRCUIT AND POINT WIRING (SUPPLY, INSTALLATION, TESTING AND

1 Recessed wiring to light point / fan point / exhaust fan point / call bell point with 1.5

sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked with

20 mm dia non-metalic PVC flexible conduit with 5 Amp, 250 V piano type switch ISI

marked and ceiling rose ISI marked mounted on MS box having front bakelite cover of

suitable size , MS box with 1.5 sq.mm FR PVC insulated single core multistrand

copper conductor as earth wire including all accesories and connection as per

direction of Engineer in Charge.

2 Recessed wiring for light / power plug with 2 x 4 sq.mm FR PVC insulated single core Meter 585 146.38 85634.64

multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible

conduit alongwith 1 x 2.5 sq.mm FR PVC insulated single core multistrand copper

conductor for loop earthing as required.

3 Circuit / Sub Main wiring in PVC Conduit

Recessed wiring to submain in 2 x 1.5 sq.mm FR PVC insulated single core

multistrand copper conductor of ISI marked confirming to IS-694/1990 in 20 mm dia

non-metalic heavy duty flexible conduit 1.6 mm thick along with 1 x 1.5 sq.mm FR

PVC insulated single core multistrand copper conductor as earth wire as equired.

Recessed wiring to submain in 2 x 2.5 sq.mm FR PVC insulated single core

multistrand copper conductor of ISI marked confirming to IS-694/1990 in 20 mm dia

non-metalic heavy duty flexible conduit 1.6 mm thick along with 1 x 1.5 sq.mm FR

PVC insulated single core multistrand copper conductor as earth wire as equired.

Recessed wiring to submain in 2 x 4 sq.mm FR PVC insulated single core multistrand

copper conductor of ISI marked confirming to IS-694/1990 in 20 mm dia non-metalic

heavy duty flexible conduit 1.6 mm thick along with 1 x 1.5 sq.mm FR PVC insulated

single core multistrand copper conductor as earth wire as equired.

Recessed wiring to submain in 4 x 10 sq.mm FR PVC insulated single core

multistrand copper conductor of ISI marked confirming to IS-694/1990 in 32 mm dia

non-metalic heavy duty flexible conduit 1.6 mm thick along with 2 x 4 sq.mm FR PVC

insulated single core multistrand copper conductor as earth wire as equired.

4 Supplying and fixing of following sizes of Steel conduit along with accessories in

recessed wiring including cutting the wall and making good the same in case of

recessed conduit as required.

5 Supplying and fixing of following sizes of PVC conduit along with accessories in

recessed wiring including cutting the wall and making good the same in case of

recessed conduit as required.

Sl. Description Unit Qty. Rate Amount

6 Supply and drawing of following sizes FR PVC insulated single core multistrand

copper conductor in existing surface / recessed STEEL/PVC conduit as required.

7 Supplying and fixing of following sizes of Metal Box along with accessories in

recessed wiring including cutting the wall and making good the same in case of

recessed conduit as required.

8 Supplying and fixing of metal box of 150 mm x 75 mm x 60 mm deep (nominal size) Each 198 483.95 95822.50

on surface or in recess with suitable size of phenolic laminated sheet cover in front

including providing and fixing 3 pin 5 / 6 amps socket outlet and 5 / 6 amps piano type

switch, connection, painting etc as required.

9.7 Supplying and fixing of Call Bell / Buzzer ISI marked suitable for DC /AC single phase Each 4 146.16 584.64

230 volts complete as required.

TOTAL CARRIED TO SUMMARY 5468566.99

B. LV / MV CABLE TRENCHING AND LAYING WITH SAND AND PROTECTIVE

1 MV cable laying up to 25 sq.mm in ground

1.1 Laying of one number of PVC insulated and PVC seathed / XLPE power cable of 1.1 Metre 144 222.10 31981.82

KV grade of size not exceeding 25 sq.mm direct in ground including excavation, sand

cushing, protective covering and refilling the trench etc. as required.

1.2 MV cable laying exceeding 25 sq.mm to 120 sq.mm in ground Metre 240 230.05 55211.52

Laying of one number of PVC insulated and PVC seathed / XLPE power cable of 1.1

KV grade of size excedding 25 sq.mm but not exceeding 120 sq.mm direct in ground

including excavation, sand cushioning, protective covering and refilling the trench etc.

1.3 MV cable laying exceeding 120 sq.mm to 400 sq.mm in ground Metre 30 238.00 7140.00

Laying of one number of PVC insulated and PVC seathed / XLPE power cable of 1.1

KV grade of size excedding 120 sq.mm but not exceeding 400 sq.mm direct in ground

including excavation, sand cushioning, protective covering and refilling the trench etc.

2 LALYING OF CABLE ON SURFACE

2.1 MV cable laying up to 25 sq.mm on surface Metre 576 48.38 27869.18

Laying and fixing of one number of PVC insulated and PVC seathed / XLPE power

cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface as required.

2.2 MV cable laying exceeding 25 sq.mm and up to 120 sq.mm on surface Metre 720 73.58 52980.48

Laying and fixing of one number of PVC insulated and PVC seathed / XLPE power

cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm on

surface as required

TOTAL CARRIED TO SUMMARY 175183.01

C. EARTHING INSTALLATION

1 G.I. Earth Pipe electrode with salt / charcoal Set 48 2884.45 138453.50

Earthing with G.I earth pipe 3 meter long 40 mm dia ISI marked including accessories

and providing masonary enclosure with cover plate having locking arrangment and

watering pipe etc with charcoal and salt as required

Sl. Description Unit Qty. Rate Amount

2 S/L of 25 mm x 5 mm Copper earth strip in 40 mm dia G.I. pipe Metre 960 707.84 679526.40

Providing and fixing 25 mm x 5 mm Copper strip in 40 mm dia G.I. pipe from earth

electrode as required.

3 S/L of 25 mm x 5 mm G.I. earth strip in 40 mm dia G.I. pipe from earth electrode as Metre 1800 665.39 1197705.60

4 P/F 6 SWG GI loop earth wire in surface / recess Metre 4000 21.73 86912.00

TOTAL CARRIED TO SUMMARY 2102597.50

ELECTRICAL SUMMARY

Item Description Amount

A. CIRCUIT CUM POINT WIRING (IN RECESSED / SURFACE PVC/ MS CONDUITS) ` 5468566.99

B. CABLES, MAINS AND SUB MAINS ` 175183.01

C. EARTHING INSTALLATION ` 2102597.50

GRAND TOTAL ` 7746347.50

GRAND TOTAL ` 7746347.50

LOW SIDE ELECTRICAL WORKS (NON-SCHEDULED ITEM)

Item Description Unit Qty. Rate Amount

A. CIRCUIT AND POINT WIRING (SUPPLY, INSTALLATION, TESTING AND

1 Wiring for AC point with 4 sq. mm. Insulated copper conductor 1100 volts grade stranded Pt 26.40 1578.64 41676.10

flexible FRLS wires of approved make in concealed minimum 2mm thick FRLS PVC

conduit (as per IS 9537 part 3) including providing and fixing of 20 amps flush mounted

switch at the normal switch level in 1.6 mm thick GI box and 32 amps 3 pin metalclad

socket outlet with ON indicator with lockable acrylic door and earthing of through the

third pin of the socket outlet and GI box with 2.5 sq. mm. PVC insulated copper

conductor flexible FRLS wire.

2 Wiring for Geyger point with 4 sq. mm. Insulated copper conductor 1100 volts grade Pt 5.50 1024.46 5634.55

stranded flexible FRLS wires of approved make in concealed minimum 2 mm thick FRLS

PVC conduit (as per IS 9537 part 3) including providing and fixing of 20 amps SP MCB in

1.6 mm thick GI box and32 amps 3 pin metalclad socket outlet (IP 56) with On indicator

with lockable acrylic door and earthing of through the third pin of the socket outlet and GI

box with 2.5 sq. mm. PVC insulated copper conductor flexible FRLS wire.

3.0 Supply, laying, installation, testing and commissioning of following PVC insulated tinned

copper conductor cable / wires in existing cable tray / GI pipes / conduits.

3.1 10 pair 0.5/0.61 mm armoured cable Meter 394.84 115.14 45460.80

4 Supply and installation, testing and commissioning following size KRONE make

telephone tag block in lockable 16 gauge sheet steel enclosure complete as required.

9.0 Supplying and fixing following modular switch/ socket on the existing modular plate &

switch box including connections but excluding modular plate etc. as required.

9.3 3 pin 5/6 amp socket outlet Each 165.00 115.58 19071.36

9.4 6 pin 15/16 amp socket outlet Each 42.90 224.22 9619.21

9.5 Telephone socket outlet Each 22.00 125.44 2759.68

9.6 TV antenna socket outlet Each 14.30 125.44 1793.79

10 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Meter 100.00 46.82 4681.60

steel/ PVC conduit as required.

11 Supplying and fixing modular blanking plate on the existing modular plate & switch box Each 103.40 32.03 3312.11

excluding modular plate as required.

12 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper

conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC

conduit as required.

TOTAL CARRIED TO SUMMARY 311639.05

B. CABLES, MAINS AND SUB MAINS

The rate shall also include the following :

1 Providing and fixing junction boxes with covers including painting.

2 Effecting adequate and proper connections at terminations.

Item Description Unit Qty. Rate Amount

3 Providing all fixing accessories such as clamping devices nuts, bolts and screws.

4 Excavation laying of cable filling of sand, brick protection, back filling of earth, watering,

ramming and making good.

5 Wherever the cables are of aluminium and bus bars of copper bimetallic lugs shall be

6 All cable shall be laid with one diameter gap.

7 All cables shall be IS approved.

8 Fire retardent paint one meter on both side of wall penetration and at termination as per

specifications.

9 Burried LT cables to be laid atleast 750 mm below ground.

10 All cutouts / Sleeves shall be sealed with fire redardant sealent as per specification.

11 No joints are allowed in the cable.

B. CABLES, MAINS AND SUB MAINS

1.0 Supplying of following 1100 volt grade XLPE insulated PVC sheathed aluminium

conductor armoured cables as per specification.

2.0 Supplying of following 1100 volt grade XLPE insulated PVC sheathed copper conductor

armoured cable as per specification.

3.0 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable

of 1.1 KV grade of following size on cable tray as required.

3.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Metre 6990.00 24.08 168319.20

3.2 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3 mm MS flat clamp) Metre 1350.00 47.60 64260.00

3.3 Above 95 sq. mm and upto 240 sq. mm (clamped with 25/40x3mm MS flat clamp) Metre 1500.00 59.02 88536.00

4.0 Supplying and making end termination with brass compression gland and aluminium lugs

for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable

of 1.1 KV grade as required.

Item Description Unit Qty. Rate Amount

5.0 Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with Each 40.00 428.96 17158.40

inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long

and fixing the same in ground as required.

6.0 Providing, laying and joining in position HDPE pipes conforming to IS:4984-1987

(Material Grade -PE- 80)/ or equivalent international standard and suitable for the

respective working pressures with all fittings and specials,e.g.couplings, tees, bends,

reducers, end plugs etc., jointing by fusion welding method as per manufacturers

recommendations all complete including excavation in all kind of soil and back filling.

This pipes will be used for transferring HV/LV Cables.

7.0 Supply and installation of following RCC (NP-2 class) Hume pipe under paved areas,

including providing 75 mm thick cement concrete all around pipe 1:3:6 (1 cement, 3

coarse sand and 6 crushed stone aggregate).

TOTAL CARRIED TO SUMMARY 5451758.76

C. CABLE TRAYS AND RACEWAYS:

The cable management system shall comprise:

1 Ladder cable trays and supports.

2 Perforated cable trays and supports.

3 Surface mounted wire ducts with brackets/ supports.

4 All cuts/perforations/folded sections where contact with wires/cables in expected shall be

5 Zinc coating shall be 120 gm/ square meter or more. The materials shall conform to

relevant IS/ BS standards for the category/ application specified.

6 The cable tray shall be factory built. Only cutting to achieve assembly system length shall

be permitted at site.

7 Accurate fabrication formed section with tolerances of + 2 mm on width and + 5 mm on

length expected.

8 Dimensional and general arrangement drawing of the system are expected to be

provided by tenderer/ cable tray/ duct supplier.

9 The system shall be designed for installation with a temperature classification of + 60

10 The cable tray/duct systems shall be suitable for against corrosion.

11 Details of fixing supports etc. shall be submitted for approval.

C. CABLE TRAYS AND RACEWAYS:

1.0 Supply and installation of under floor GI raceway with necessary hardware including of

supporting with threaded hitech rods etc. complete,

1.1 200 mm wide x 40 mm deep raceway Metre 80.00 3241.39 259311.58

1.2 150 mm wide x 40 mm deep raceway Metre 200.00 2141.42 428283.78

2.0 Providing and fixing of 250 x 250 x 60 mm deep (Nominal size) junction box including Each 20.00 3344.88 66897.60

providing 3 mm thick GI steel cover required as per specification.

Item Description Unit Qty. Rate Amount

3.0 Providing and fixing of 200 x 200 x 60 mm deep (Nominal size) junction box including Each 40.00 2767.48 110699.01

providing 3 mm thick GI cover required as per specification.

4.0 Supply and fixing of pregalvanized factory fabricated GI ladder (or equivalent wire mesh

as per specification) type cable tays, with radial bends, supports and fixing hardware etc.

with of the following sizes as per specification.

4.2 1000 mm wide

Runners 25 x 100 x 25 x 3 mm

Rungs 20 x 40 x 20 x 3 mm 250 mm C/C

2 No. suspenders 40 x 40 x 5 mm GI angle 1500 mm C/C (1 vertical and 1 horizontal RM 40.00 2,454.76 98,190.42

welded and bolted) with 2 No. GI hangers for support as per site requirement

4.3 750 mm wide

Runners 20 x 75 x 20 x 2.5 mm

Rungs 20 x 30 x 20 x 2.5 mm 250 mm C/C

2 No. suspenders 32 x 32 x 4 mm GI angle 1800 mm C/C (1 vertical and 1 horizontal RM 1200.00 1,714.56 2,057,471.81

welded and bolted) with 2 No. GI hangers for support as per site requirement

5.0 Supply and fixing of perforated type (or equivalent wire mesh type) GI cable trays with

support for hanging from the ceiling of the following sizes as per specification.

TOTAL CARRIED TO SUMMARY 3340870.68

E CONVENTIONAL LIGHTNING PROTECTION SYSTEM

1.0 Supply of Vertical Electrolytic Copper Lighting Arrester of 16 mm dia, 1000 mm long Nos. 55.00 4,162.82 228,954.88

with Gun Metal base plate .

2.0 Supply 8 mm round aluminium conductor for horizontal lightning protection - run in roof. RM 594.00 200.34 118,999.30

3.0 Supply of roof conductor holder for 8 mm round aluminium conductor made of Gun Nos. 599.50 243.26 145,837.10

Metal for horizontal installation. The distance between each holder should be min of 1

4.0 Supply of T connector for connecting of 8 mm Al round conductor . The connector Nos. 57.20 637.43 36,461.06

should be of Gun Metal with SS nuts and bolt.

5.0 Supply of Cross connector for connecting of 8 mm Al round conductor . The connector Nos. 28.60 637.43 18,230.53

should be of Gun Metal with SS nuts and bolt.

6.0 Supply of Expansion piece along with connector to compensate the expansion of round Nos. 68.20 689.47 47,021.61

8 mm Al conductor when temperature variation . Connection should be in every 20 mtr.

7.0 Supply of 8 mm round aluminium conductor as a down conductor mounted in the RM 385.00 200.34 77,129.18

surface of wall which will carry the lightning current to earth pit.

8.0 Supply of Down conductor holder for 8 mm round aluminium conductor of min distance Nos. 385.00 247.17 95,159.37

between the wall to the conductor will be of 85 mm. The distance between each holder

should be min of 1 mtr.

9.0 Supply of straight connector for connecting of 8 mm Al round conductor . The connector Nos. 39.60 637.43 25,242.28

should be of Gun Metal with SS nuts and bolt.

Item Description Unit Qty. Rate Amount

10.0 Supply of 6 digit lightning strike counter. Nos. 2.20 17,561.88 38,636.14

11.0 Supply of Test Joint Point for 8 mm round aluminium conductor, the size should be of Nos. 22.00 6,244.22 137,372.93

25 x 3 x 150 mm copper in ABS boxes.

12.0 Supply of UL approved low carbon high tensile steel rod with copper coating of min 254 Nos. 55.00 18,862.76 1,037,451.80

micron JK Chemrode - 317 CBR the dia should be 17.2 mm with length of 10 feet ( 3000

mm) . The rod shall be as per IEC 62561-2 and approved by UL 467. The rod shall be

tested from NABL lab for current discharge not less then 46kA peak.

The Chemrode shall be surrounded with 25 kg ( 1 bag) of Earth enhance materiel JK

Reslow according to IEC 62561-7 and the Chemical resistance value shall not increase

more then 0.067 Ωm and same will be tested from NABL lab. along with earth pit

chamber made up polyplastic. Size of -254x330x260 MM

13.0 Providing and fixing G.I. tape 25 mm X 6 mm thick on parapet or surface of wall for RM 550.00 221.15 121,632.28

lightning conductor complete as required.

TOTAL CARRIED TO SUMMARY 2,128,128.45

F SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF LIGHTING

FIXTURES, CEILING FANS, EXHAUST FANS AND ACCESSORIES

The rates shall include all components that may be required to make the installation

complete in all respects such as :

1 Including All lamps, accessories & electronic ballast unless otherwise specified.

2 Internal wiring between accessories.

3 Earthing terminal.

4 Complete provision for installation.

5 The vendors should select the fixtures according to lux level given in drawings & LPD

shall be maintained below 0.7W/sqft.

6 The vendors should Submit the detailed lux level calculation & LPD calculation.

7 Suitable length of GI down rod, hanger and connecting wires where called for..

8 Wires for connecting the fixtures to the point through connector block.

9 All metal blocks to serve as base of fixtures..

10 Bonding with earth wires.

11 Drilling holes in supports wherever required.

12 Bonding with earth wires.

13 Fixing clamps, GI bolts and nuts, brass screws, saddles, rawl bolts and other fixing

accessories as required.

14 Testing of all fixtures before and after installation.

F SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF LIGHTING

FIXTURES, CEILING FANS, EXHAUST FANS AND ACCESSORIES

1.0 Supply, Receiving, storing, installation & handling of following lighting fixtures/ Ceiling

Fan/ Exhaust Fan with all fixing accessories etc. as required.

1.1 Wall/ surface mounted T8 light fixture complete with 1X20 W (LED) lamps, ballast and Each 1471.80 1339.52 1971505.54

all accessories as required .

Item Description Unit Qty. Rate Amount

1.2 Wall/ surface mounted T8 light fixture complete with 2X20 W (LED) lamps, ballast and Each 35.20 2163.84 76167.17

all accessories as required.

1.3 Supply of Surface mounted Round 18/20 W LED Downlight fixture complete with all Each 621.50 2009.28 1248767.52

accessories as required.

1.4 Decorative Bracket light with 9W LED lamp Each 15.40 2016.00 31046.40

1.5 Aesthetic Wall Mounted mirror light luminaries suitable 10W 2' LED mirror for higher light Each 36.30 865.54 31418.96

1.7 LED Trackmounted projector light with system lumen of 4000 @ system load of 41W.+ 3 Each 6.00 6182.40 37094.40

nos. 1 mtr. Track

1.8 Bulk Head lighting fixture 10W, 1000 Lumen Each 44.00 875.84 38536.96

1.15 48" dia sweep ceiling fan (BEE 5 star rated) with step type modular fan regulator of Each 273.90 2032.13 556599.86

approved make complete with all accessories.

1.16 Exhaust Fan 225 mm sweep (Heavy duty) . Each 39.60 2483.71 98355.00

TOTAL CARRIED TO SUMMARY 4089491.80

G. SUPPLY, INSTALLATION OF LIGHTING FIXTURES AND SUPPLY &

INSTALLATION OF CABLES FOR EXTERNAL/ LANDSCAPE LIGHTING

1.0 Suplying, Receiving, storing handling, installing, testing and commissioning of the

following lighting fixtures.

1.1 Light fixtures of 80W LED flood light with LED lamp or approved equal in quality and No. 8.00 11849.60 94796.80

1.2 LED type Bollard lighting fixture 7W, with lamp and ballast as per requirement or No. 15.00 8758.40 131376.00

approved equal in quality .

1.3 Street Light fixture of 20 W LED of IP 66 protectioncomplete with lamp, electric ballast No. 16.00 4121.60 65945.60

etc as required.

1.4 7M high MS decorative poles (5.6 M above & 1.4 M below ground) Kesselec Make No. 8.00 20865.60 166924.80

Blenheim model or equivalent

1.5 Supply of 4m Octagonal GI pole with top dia of 70mm, botoom dia 130 mm, base plate No. 16.00 11592.00 185472.00

dimension of 200mmX200mmX12mm; PCD of 225 mm and Sheet thickness of 3mm.

Along with 4 Nos. foundation bolts. Similar to Wipro make 4m Pole or equivalent

Philips/LT Make.

2.0 Providing and fixing of following PVC insulated copper conductor 1100 volts grade

stranded flexible wire in GI conduit including providing and fixing of conduit concealed or

surface mounted as indicated PVC insulated green colour copper stranded flexible wire

for earthing and making connection complete.

2.1 3 x 4 sq.mm wire in 25 mm dia conduit. RM 650.00 322.56 209664.00

2.2 3 x 2.5 sq.mm wire in 25 mm dia conduit. RM 200.00 292.32 58464.00

3.0 Providing, installation, testing and commissioning of 200 x 150 x 125 mm polycarbonate Nos. 34.00 4334.40 147369.60

weather proof (IP-55) junction box recessed in wall or surface mounted as required for

housing of 1 no. 10 amps SPN MCB‟s suitable size of terminal blocks complete.

Suitable length of GI pipe up to junction box shall also be provided for laying of cables.

4.0 Supply, installation, testing and commissioning of following polycarbonate weather proof

(IP-55) junction box suitable for pole mounting / underground complete as required.

TOTAL CARRIED TO SUMMARY 1340287.20

H. SYNCHRONIZATION PANEL/ LT PANELS/ DISTRIBUTION BOARDS AND BUS

Item Description Unit Qty. Rate Amount

The main LT panel cum DG Synchronization panel and APFC panel shall be

designed as per IEC 61439-1 & 2 for Total Type tested Assembly (TTA); IP-42 and

seismic zone protection level-3. The rates for the distribution boards from the breakers

and instruments shall also include the following :

1 Supporting rigid steel framework.

2 Cubicle type, 2 mm CRCA sheet steel enclosed & Type 3b (4b for TTA) modular

3 Complete with interconnections and distribution bus bars along with connector strip.

4 Inert gas fire suppresiion system inside the panel compartments

5 Proper bonding to earth as per standard.

6 Painting/lettering on Breakers and distribution boards, the location they serve, providing

on each panel its circuit diagram.

7 Providing cable clamps / supports within distribution boards cable alley.

8 TPN ACB‟s / MCCB‟s shall mean 3 pole ACB‟s / MCCB‟s with adequate size of neutral

9 All MCB‟s shall be of minimum 10 KA breaking capacity.

10 The breaking capacity of MCCB‟s are mentioned panel wise. The releases of MCCB‟s

shall be as per BOQ, SLD and as per following:

i. MCCB rating upto 250 amps with thermal magnetic releases

ii. MCCB rating above 250 amps with microprocessor based releases.

11 Distribution panels shall be Powder Coated with Siemens gray paint shade no. RAL-

12 Degree of protection for following type of distribution panel enclosure shall be as per

i. IP 42 for indoor panels.

ii. IP 55 for outdoor panels.

13 All MCCB‟s shall be provided with operating mechanism for door interlock.

14 All main bus bars shall be fabricated out of electrolytic grade copper having current

density of 1.4A/ Sq.mm or aluminium having current density of 0.7A/ Sq.mm as per SLD

and BOQ for design consideration.

15 GI earth bus shall be provided through out the length of each board as per schematic

16 All measuring instruments (Meters) shall be of digital electronic (LED Type) of approved

17 All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire.

18 All panels shall have provision of the following:

19 Pad locking of MCCB‟s handles in “OFF” Position.

20 All MCB‟s used for protection of resistive and lightly inductive load shall be type “B”

characteristic and inductive (motor) load shall be of type “C” characteristic and discharge

lamps and UPS etc. shall be of type D characteristic.

Item Description Unit Qty. Rate Amount

21 All incoming and outgoing air circuit breakers shall be placed on middle portion of the

vertical in single tier formation.

22 CT‟s shall be properally mounted and clamped. Connection of CT‟s for measuring

instrument / relays shall be done through connector / terminals.

23 Model, current capacity location and frame size of switchgear shall be written inside of

the panel doors with paint / permanent marker as approved shop drawings / site

24 Compliance to the technical specifications.

H MAIN LT PANELS/ DISTRIBUTION BOARDS AND BUS DUCTS

Design, fabrication, assembling, wiring, testing, supply, forwarding to site, unloading,

shifting to location, inspection, installation, testing and commissioning of M.V.Distribution

Boards suitable for 415V, 3 phase, 4 wire, 50 Hz distribution system (Design verified as

per IS/ IEC: 61439- 1 & 2) fabricated out of 14 gauge CRCA sheet steel in cubicle

formation, compartmentalized, form 4b consutruction, free standing floor mounted, dust

and vermin proof with reinforcement of suitable size angle iron, channel, `T‟ sections

and/ or flats wherever necessary. 16 gauge CRCA sheet steel shall be used for final

distribution panels. 3 mm thick cable gland plates shall be provided on top as well as at

the bottom of the panels. Panels shall be treated with all anticorrosive process before

powder coating as per specifications and final approved shade. The panel shall also

include inbuilt inergent gas based fire suppression system inside the panel.

2 No. earthing terminals shall be provided for all distrtibution panels. Panels shall be

suitable for 415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall also be

provided in case of large panels. Approval shall be taken for each panel in the form of

shop drawings before fabrication. Galvanised hardwares with zinc passivation shall be

used in fabrication of panels.

SYNCHRONIZATION PANEL/ MAIN LT PANEL/ OTHER TTA PANELS

Supply, Installation, Testing and Commissioning of cubicle type DG

SYNCHRONIZATION PANEL/ MAIN LT CUM DG CHANGE-OVER PANEL AND

OTHER TTA PANELS as per IEC 61439-1 & 2, IP 42 (Design verified) with seismic

zone protection -3, suitable for 415V+/-10%, 3 Phase, 4 wire 50 Hz AC supply system,

tested for 12 kV impulse withstand voltage,form 4b construction, fabricated in

compartmentalized modular design from CRCA sheet steel of 2 mm thick for frame work

and covers, plates i/c cleaning & finishing complete with 7 tank process for powder

coating in approved shade, having TPN electrolytic grade copper bus bars for high

conductivity, SMC bus bar supports,with short circuit withstand capacity of 50 KA for 1

sec, internal arc containment tested IEC 61641 50 kA for 0.3 sec at HBB, VBB & Cable

Chamber, bottom base frame of not less than 75 mm thickness, fabrication shall be done

in transportable sections, entire panel shall have a common earth bar sized for

prospective earth fault , solid / flexible connections from of the engineer-in-charge. The

product performance shall carry guarantee for 10 years against any leakage.

For all surface.val and laying 15 mm thick densified edges calicum silicate ceiling tiles of

approved texture in the grid, including, cutting/ making opening for services like diffusers,

grills, light fittings, fixtures, smoke detectors etc., n all respect and must follow tech

specs & drawings.

1.0 AUTO STARTING, AUTO SYNCHRONIZING, AUTO LOAD SHARING AND LOAD

BUS SECTION - I

Incoming Air Circuit Breaker- (From 400 kVA Transformer 1)

800 amps 4 pole, 50 kA, electrically operated fully draw out type air circuit breaker with

microprocessor release unit (Type 6.0H of Schneider or equivalent), for short circuit,

over current and earth fault protection with adjustable setting as per specification and

with following accessories- 1 set :

Item Description Unit Qty. Rate Amount

i Digital load manager (conzerve – EM 6400 with RS-485 or equivalent) of accuracy class-

I with 2 No. 800/5 amps 15VA CTs.

ii Phase indicating lamps protected by 6 amps SP MCB‟s- 3 Set

iii Three Phase Under voltage relay MV12 or equivalent (27) - 1 Set

iv Three Phase Over voltage relay MV 12 or equivalent (59) - 1 Set

v Breaker ON/ OFF/ TRIP indicating lights with control MCB‟s- 1 Set

vi 24 V DC Shunt trip coil. - 1 Set

vii 240 V AC under voltage release. - 1 Set

viii Auto-manual / test selector / switch - 1 Set

ix Breaker control switch - 1 Set

x Auxiliary contacts required for necessary interlocking of breakers.

xi Three phase Voltage sensor relay shall be protected by 2 amps TP MCB‟s-1 Set

xii Transient voltage class B surge supressor (100 kA) (Lines to Neutral) & (Neutral to

Earth) suitable for 3 phases - 1 Set

xiii Digital voltmeter with inbuilt selector switch- 1 set

Incoming Air Circuit Breaker-(From 500 kVA DG)

1000 amps 4 pole, 50 kA, electrically operated fully draw out type air circuit breaker with

microprocessor release unit (Type 6.0P of Schneider make or equivalent), for short

circuit, over current and earth fault protection with adjustable setting as per specification

and with following accessories- 1 Set :

a DG controller with AMF of Cummins / Woodword / DEIF/ DEEP SEA or equivalent make

with following measurement and protection features:

i over speed, under speed, speed/ frequency mismatch, excitation failure protection for

ii Over load, short circuit, reverse power, unbalance load, inst. Over current, event

recorder for Alternator

iii Auto/Manual/OFF mode, soft keys for speed raise lower and frequency raise lower

(required for manual mode). Configurable discrete alarm inputs, configurable discrete

iv Communication protocols such as CAN bus/ RS 485/ other open protocol

b Digital Load manager (conzerve – EM 6400 or equivalent with RS 485 and open protocol

for BMS) of accuracy class-I, with 3 Nos. 1000/5A amps 15VA class 1.0 CTs to measure

and display the following electrical quantities :

i Total active energy (KWH/MWH)

ii Maximum demand (KVA/MVA) (KW/MW)

iii Maximum demand reset count.

iv Instantaneous power factor

v Logging of active energy eight time of a day

Item Description Unit Qty. Rate Amount

viii Frequency / Harmonics

c Battery charger as described in the Specifications and described below:

i AC Input : 230 V + 10% AC 50 Hz single phase.

ii DC Output : To float / boost charge suitable number of batteries and also supply a

continuous load.

iii Current Rating: 40 amps

iv Float Mode: 27.0 V nominal (Adjustable) between 24-28.0 V.

v Boost Mode: 29.0 V nominal (Adjustable) between 24-32.0 V.

vi Voltage Regulation: + 2% for AC input variation of 230 V + 10%. Frequency Variation of

50 Hz + 5% and DC load variation 0-100%

vii Ripple: Less than 5%

d 3 Nos. phase indicating light with 2A control MCB‟s and toggle switches.

e Breaker ON / OFF / TRIP/ Trip circuit healthy indicating lights with control MCB‟s. - 1

f 0-500 volts digital electronic voltmeter with selector switch and control MCB‟s.

g 3 nos. 1000/5A, 5VA line CTS for controller

h 3nos. 415/110V line PTs with control fuses, for feedback to controller.

i Grid supply voltage sensing relay.

j Battery charger voltmeter of range 0-50V and ammeter of range 0-50A for trickle and

boost charging.

k Excitor field DC voltmeter and ammeter.

l Lockable Emergency stop push button.

m Three indicating lamps 'load on set‟, „Load on Mains‟ and 'Set fail to start‟.

n Restricted Earth Fault Relay including all accessories.

o 16 Window alarm annunciators panel with hooter, push buttons, aux. Contactors etc as

required as per specification.

p Five push buttons – start, stop, reset, test and accept.

q Over voltage and under voltage relays.

r Master trip relay, trip circuit supervision relay and cranking relay.

1000 A TPN electrolytic grade Al bus bar, 50 kA for 1 sec. with colour coded heat

shrinkable insulation sleeve.

i. 400 amps, 50kA, 3 Pole MCCB - 1 No. (For 125 kVAr CAPACITOR PANEL 1)

ii. 400 Amps, 50 kA, 4 Pole MCCB - 1 no.

iv. 250 Amps, 50 kA, 4 Pole MCCB - 1 no.

v. 160 Amps, 50 kA, 4 Pole MCCB - 2 nos.

Item Description Unit Qty. Rate Amount

vi. 63 Amps, 50 kA, 4 Pole MCCB - 3 nos.

Bus Coupler 1 (Between Bus Section I & Bus Section II)

1000 amps, 50 kA, 4 pole electrically operated fully draw out type air circuit breaker

without release unit ,with ON/ OFF/ TRIP indicating lamps with control MCB‟s, breaker

control switch etc - 1 Set.

Incoming Air Circuit Breaker- (From 400 kVA Transformer 2)

800 amps 4 pole, 50 kA, electrically operated fully draw out type air circuit breaker with

microprocessor release unit (Type 6.0H of Schneider or equivalent), for short circuit,

over current and earth fault protection with adjustable setting as per specification and

with following accessories- 1 set :

i Digital load manager (conzerve – EM 6400 with RS-485 or equivalent) of accuracy class-

I with 2 No. 800/5 amps 15VA CTs.

ii Phase indicating lamps protected by 6 amps SP MCB‟s- 3 Set

iii Three Phase Under voltage relay MV12 or equivalent (27) - 1 Set

iv Three Phase Over voltage relay MV 12 or equivalent (59) - 1 Set

v Breaker ON/ OFF/ TRIP indicating lights with control MCB‟s- 1 Set

vi 24 V DC Shunt trip coil. - 1 Set

vii 240 V AC under voltage release. - 1 Set

viii Auto-manual / test selector / switch - 1 Set

ix Breaker control switch - 1 Set

x Auxiliary contacts required for necessary interlocking of breakers.

xi Three phase Voltage sensor relay shall be protected by 2 amps TP MCB‟s-1 Set

xii Transient voltage class B surge supressor (100 kA) (Lines to Neutral) & (Neutral to

Earth) suitable for 3 phases - 1 Set

xiii Digital voltmeter with inbuilt selector switch- 1 set

i. 400 amps, 50kA, 3 Pole MCCB - 1 No. (For 125 kVAr CAPACITOR PANEL 1)

ii. 400 Amps, 50 kA, 4 Pole MCCB - 1 no.

iv. 250 Amps, 50 kA, 4 Pole MCCB - 1 no.

v. 160 Amps, 50 kA, 4 Pole MCCB - 2 nos.

vi. 63 Amps, 50 kA, 4 Pole MCCB - 3 nos.

Note on Main LT cum DG Changeover Panel :

All outgoing feeders shall have suitable range of followings:

i. All breakers shall be electrically interlocked as per schematic diagram.

ii. All ACB‟s/ MCCB‟s shall be suitable for 50 KA breaking capacity unless otherwise

Item Description Unit Qty. Rate Amount

iii. PLC for DG and transformer load management and supervision to be provided.

iv. Three phase indicating lamps shall be protected by 6 amps SP MCBs.

v. All outgoing feeders shall be provided with built-in short circuit & earth fault relay module.

vi. All outgoing (except spare feeder) shall have dual Electronic energy meter (EM-6438

with RS-485 or equivalent) with required number of CT's as required.

vii. Wiring and supply, installation of space heater, humidistat and control MCB‟s shall be

provided all vertical sections.

viii. Suitable danger board shall be provided.

ix. All bus bar section/ backside panels shall have pad locking facility and hinged type door.

x. 9 W fitting with CFL lamp, switch shall be provided in each vertical section.

xi. Incoming breakers shall have suitable provision for bus duct connection..

xii. All Electronic Energy meter shall be pre wired for BMS connection up to central point

within the panel with shielded cable.

DG Synchronization cum Changeover Panel as described above. Set 1.00 2,323,552.00 2,323,552.00

2.0 MAIN BUILDING DISTRIBUTION PANEL (MDB - 1.1)

400 Amps 4P MCCB with microprocessor based release and with following accessories:

i Dual source digital electronic energy meter with inbuilt selector switch and 400/5 amps

15 VA, CL 1 CTs . - 1 Set

ii Phase indicating light shall be protected by 2 amps SP MCB's. - 3 Set

500 amps TPN Aluminium bus bars with heat shrinkable insulation sleeve. - 1 Set

i. 200 Amps 4 Pole MCCB with Thermo-magnetic release- 2 Nos.

ii. 100 Amps 4 Pole MCCB with Thermomagnetic release- 3 Nos.

iii 63 Amps 4 Pole MCCB with Thermomagnetic release- 8 Nos.

i. All MCCB's shall be of 25 KA (Ics) breaking capacity.

ii All MCB's shall be of 10 KA breaking capacity.

iii. All the outgoing feeders shall have Direct / CT operated VAF meters of accuracy class-

MDB - 1.1 described as above. Set. 1.00 631635.20 631635.20

3.0 GUEST HOUSE DISTRIBUTION PANEL (MDB 1.2)

Item Description Unit Qty. Rate Amount

160 Amps 4P MCCB with microprocessor based release and with following accessories:

i Dual source digital electronic energy meter with inbuilt selector switch and 160/5 amps

15 VA, CL 1 CTs . - 1 Set

ii Phase indicating light shall be protected by 2 amps SP MCB's. - 3 Set

200 amps TPN Aluminium bus bars with heat shrinkable insulation sleeve. - 1 Set

i. 100 Amps 4 Pole MCCB with Thermomagnetic release- 1 Nos.

ii. 63 Amps 4 Pole MCCB with Thermomagnetic release- 8 Nos.

i. All MCCB's shall be of 25 KA (Ics) breaking capacity.

ii All MCB's shall be of 10 KA breaking capacity.

iii. All the outgoing feeders shall have Direct / CT operated VAF meters of accuracy class-

MDB - 1.2 described as above. Set. 1.00 221793.60 221793.60

4.0 UPS OUTPUT PANEL

A. Incoming (From 30 kVA UPS)

100 Amps, 4 pole, 35 kA MCCB

VAF digital electronic meter with inbuilt selector switch -2 Sets

Phase indicating light shall be protected by 6 Amps SP MCB's - 6 Set

150 Amps TP+2N electrolytic grade Copper bus bars, 35 kA with colour coded heat

shrinkable insulation sleeve. - 1 Set

i. 40 Amps DP MCB - 14 Nos. (6 Nos. for ELDBs, 1 No. for ELV DB and 4 Nos. as

i. All MCCB's shall be of 35 KA (Ics) breaking capacity.

ii. All MCB's shall be of 10 KA breaking capacity.

iii. Frequency and impedance matching between two incomers.

UPS OUTPUT PANEL as described above. Set. 1.00 127,512.00 127,512.00

5.0 EXTERNAL LIGHTING PANEL (IP-55)

A. Incoming (From Emergency panel Bus section II)

Item Description Unit Qty. Rate Amount

One(1) - 80A, TPN, 35 kA MCCB with thermo-magnetic release with following

VAF digital electronic meter with inbuilt selector switch and 100/5 Amps suitable VA, CL

Phase indicating light shall be protected by 6 Amps SP MCB's - 3 Set

150 Amps TPN electrolytic grade Aluminium bus bars, 35 kA with colour coded heat

shrinkable insulation sleeve. - 1 Set

i. 2 Set each having "12 Nos. 16/20/25 amps SP MCB with 3 Nos. 63 amps DP ELCB per

phase as outgoing with 1 No. 0-24 hour timer switch, 1 No. 70 amps TP Contactor and 1

No. 63 amps MCB" as incoming , push button etc complete as required.

ii. 25 Amps 4P MCB + ELCB - 4 Nos. (3 Nos. for utility points and 1 No. as spare).

i. All MCCB's shall be of 35 KA (Ics) breaking capacity.

ii. All MCB's shall be of 10 KA breaking capacity.

iii. All ELCB's shall be of 100 mA sensitiviity.

iv. The External Lighting panel shall be finalized after finalization of area lighting layout.

EXTERNAL LIGHTING PANEL described as above Sets. 2.00 182,187.60 364,375.20

6.0 PLUMBING DISTRIBUTION PANEL (MDB 1.3)

100 amps 4P MCCB with the following accessories:

a. 0-500 volts 96 x 96 mm square ammeter with selector switch shall be protected by 2

amps TP MCB-1 Set

b. 0-100 amps 96 x 96 mm square voltmeter with selector switch and 100/5 amps 10 VA

c. Phase indicating lamps shall be protected by 2 amp SP MCB-3 Sets

150 amps TPN (25 KA) Aluminium bus bar with heat shrinkable insulation sleeves colour

a. 2 Nos. suitable rating MPCB for 2.2 kW each STAR DELTA starter and outgoing

feeder to DOMESTIC Water transfer pumps motor - Main (including 1nos. standby).

Each compartment shall contain auto / manual selector swtich and indicating /

pushbutton lamps with MCB for ON / OFF / TRIP of motor.

b. 2 Nos. suitable rating MPCB for 1.0 kW each direct on line starter and outgoing

feeder to Plumbing Plant Room Sump Pump (including 1 no. standby). Each

compartment shall contain auto/manual selector switch and indicating lamps with MCB‟s

for „ON/OFF/TRIP' status of motor

c. 2 Nos. suitable rating MPCB for Nos. 2.2 kW each direct on line starter and outgoing

feeders to Raw Water Feed pump (including 1 no. standby). Each compartment shall

contain auto/manual selector switch and indicating lamps with MCB for „ON/OFF/TRIP‟

status of motor

Item Description Unit Qty. Rate Amount

All MCCB's to be suitable for motor duty and shall be of 25 KA breaking capacity.

Provision shall be made for providing potential free contacts to all pumps starters for

connection to building automation system.

All motor starter shall be provided with Automatic level controller.

Overflow alarm must be provided at the plant room

Electrical panel must have the Auto announciator to indicate the system failure if any

Plumbing DistributionPanel (MDB 1.4) as described above Set 1.00 76185.20 76185.20

7.0 CAPACITOR BANKS WITH DETUNED FILTER IN AUTOMATIC CONTROL UNITS -

AS PER IEC 61439 DESIGN VERIFIED

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning

of Automatic control panels with low loss mixed dielectric /APP/MPP type capacitors,

fabricated out of 14 gauge CRCA sheet steel in cubicle compartmentised, free

standing, floor mounted, dust and vermin proof with reinforcement of suitable size,

angle iron, channel, „T‟ sections and / or flats wherever necessary. Cable gland plates

shall be provided on top as well as at the bottom of the panels. Panels shall be treated

with all anticorrosive process before powder coating as per specifications and final

approved shade. 2 Nos. earthing terminals shall be provided for all distrtibution

panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50 HZ supply system. Lifting

hooks shall also be provided in case of large panels. Approval shall be taken for each

panel in the form of shop drawings before fabrication. Galvanised hardwares with zinc

passivation shall be used in fabrication of panels.

It shall provide rated 150KVAR . The panel shall also comply with following :

400 Amps TP MCCB incomer with 50KA breaking capacity to be provided :

500 Amps TPN aluminium bus bars with heat shrinkable insulation sleeve. - 1 Set

i. 125 amps TPN MCCB - 1 Set

ii. 100 amps TPN MCCB - 2 Set

iii. 32 amps TPN MCCB - 3 Set

iv. “ON” /”OFF” push buttons and indicating lamps. - 7 Set.

v. 50 kVAR Capacitors,480V with 7% detuned filters- 1 Set.

vi. 25 kVAR Capacitors, 480V with 7% detuned filters- 2Set.

vii. 10 kVAR Capacitors, 480V detuned filters- 2 Set.

viii. 5 kVAR Capacitors, 480V without detuned filters- 1 Set.

Microprocessor APFC controller shall continuously monitor all three phases and displays

various Electrical Parameters like voltage, input current, capacitive current, KVA

demand,KW, Power Factor, self diagnostic error code indication with printout facility of

the above with RS 232C port. Controller should mounted on the front side of the panel.

It shall have data logging for minimum 2 months, it shall provide thyristor output for

maximum 16 stages.

Fast response time of „ON‟ capacitors 20-60 miliseconds.

Super fast electronic fuse and links of the proper rating to be used for grouping the

capacitor banks. Capacitor shall be connected with fast discharge resistances.

Thyristor having suitable capacity to carry expected current continuosly.

Necessary control and firing card with proper wiring and lugs of the required rating to be

Heavy duty exhaust fans to be provided for cooling Thyristors.

Item Description Unit Qty. Rate Amount

LED indication for number of capacitor banks „ON‟.

LED indication of Power Factor lagging or leading.

Auto/manual selector switch with necessary wiring to operate APFC panel in manual

mode bypassing APFC relay.

The APFC system shall be provided with following :

a. Over voltage.

b. Voltage imbalance.

c. Over temperature-system should be in standby mode and automatically restart after

above condition restored.

d. Total Harmonic Distortion

7% of series reactor having linearity as (2.08). €In with L=0.95Ln

Capacitor Units shall have 480 V and rating shall be suitably increased considering

reactors into account.

Capacitor automatic control panel (125 kVAR)

as described above. Set 2.00 607292.00 1,214,584.00

8.0 FINAL DISTRIBUTION BOARDS

Supply, installation, testing and commissioning of the following DB's fabricated out of 1.6

mm thick CRCA sheet steel in cubicle compartmentalized, dust and vermin proof, double

door construction, powder coated with approved shade and partitions to segregate

phases. Approved lockable covers with padlocking arrangement, recessed in wall or

surface mounted final distribution boards of the following description:

4+6+12(36) way TPN DB (PPI), 36 No.10/ 16/ 20 Amps SP MCB‟s as outgoing with 3 Nos. 2.00 28,336.00 56,672.00

No. 40 Amps DP ELCB‟s of 30 mA leakage current and 1 No. 63 Amps 4 pole MCB as

incomer with separate neutral link for each phase.

4+6+8(24) way TPN DB, 24 No.10/ 16/ 20 Amps SP MCB‟s as outgoing with 3 No. 40 Nos. 4.00 22,540.00 90,160.00

Amps DP ELCB‟s of 30 mA leakage current and 1 No. 63 Amps 4 pole MCB as

incomer with separate neutral link for each phase.

4+6+4(12) way TPN DB, 12 No.10/ 16/ 20 Amps SP MCB‟s as outgoing with 3 No. 40 Nos. 4.00 19,320.00 77,280.00

Amps DP ELCB‟s of 30 mA leakage current and 1 No. 63 Amps 4 pole MCB as

incomer with separate neutral link for each phase.

2+12 way SPN DB, 12 No.10/ 16/ 20 Amps 'D' curve SP MCB‟s as outgoing with 1 No. Nos. 6.00 9660.00 57,960.00

25 Amps DP ELCB + MCB as incomer with separate neutral link for each phase.

9.0 Supply, installation, testing and commissioning of 100 amps 4 Pole MCB isolator with in Nos. 2.00 6311.20 12,622.40

sheet steel enclosure of approved make design and painted with approved paint shade.

Item Description Unit Qty. Rate Amount

10.0 Supply, installation, testing and commissioning of 63 amps 4 Pole MCB isolator with in Nos. 4.00 4765.60 19,062.40

sheet steel enclosure of approved make design and painted with approved paint shade.

11.0 Supply, installation, testing and commissioning of 40 amps 4 Pole MCB isolator with in Nos. 2.00 3297.28 6,594.56

sheet steel enclosure of approved make design and painted with approved paint shade.

12.0 Supply, installation, testing and commissioning of 16 amps 4 Pole Metal clad socket with Nos. 2.00 4121.60 8,243.20

MCB protection in Polycarbonate enclosure of approved make design and painted with

approved paint shade. (AC indoor units)

TOTAL CARRIED TO SUMMARY 5288231.76

1.0 Supply, installation, Testing and commissioning of the following UPS SYSTEM as per

specifications and complete in all respects.

1.1 30 KVA modular type UPS with 30 min battery backup of 3 phase input & 3 phase SET 1.00 1228752.00 1,228,752.00

2.0 2.5 kVA stand alone UPS with 30 min. battery backup of 1 phase input & 1 phase output. SET 2.00 122875.20 245,750.40

3.0 Site Acceptance Test (SAT) at full load on site complete with load bank, cabling, tools LOT 1.00 56834.09 56,834.09

and tackles etc.

4.0 Supply and fixing in position 1000 mm wide rubber matting of 1100 volts grade as per RM 10.00 3196.91 31,969.06

electricity rules (exact length rubber mats to be worked out as per site requirement).

Thickness of rubber mats shall be not less than 6 mm.

5.0 Providing and fixing steel structure work for supporting the above 3 sets of UPS & LOT 1.00 88803.27 88,803.27

battery cabinets.

TOTAL CARRIED TO SUMMARY 1652108.83

ELECTRICAL SUMMARY

Item Description Amount

A. CIRCUIT CUM POINT WIRING (IN RECESSED / SURFACE PVC/ MS CONDUITS) ` 311639.05

B. CABLES, MAINS AND SUB MAINS ` 5451758.76

C. CABLE TRAYS AND RACEWAYS: ` 3340870.68

E. LIGHTNING PROTECTION SYSTEM ` 2128128.45

F SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF LIGHTING ` 4089491.80

FIXTURES AND ACCESSORIES

G. SUPPLY, INSTALLATION OF LIGHTING FIXTURES AND SUPPLY & ` 1340287.20

INSTALLATION OF CABLES FOR EXTERNAL/ LANDSCAPE LIGHTING

H. MAIN LT PANEL, UTILITY PANELS AND DBs ` 5288231.76

I. UPS SYSTEM ` 1652108.83

GRAND TOTAL ` 23602516.52

GRAND TOTAL ` 23602516.52

ELECTRICAL HV INSTALLATION WORK (NON-SCHEDULED ITEM)

SL. DESCRIPTION OF ITEMS UNIT QTY Rate Amount (Rs.)

PART-1: HV INSTALLATION

PART-1: SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF SUB-

STATION EQUIPMENT

1 11kV MAIN H.T.PANEL

Supply, installation, testing and commissioning of factory assembled, 11kV,

350MVA, 3phase, 50Hz. fully insulated, indoor type, main HT Panel consisting of

11kV, 17.5 kA symmetrical for 3 sec. as per following specifications and as per

general specifications and technical specification as required complete. The

panel shall be IP4X protection. The configuration of the breaker shall be one (1)

incomer cum outgoing feeder. Power pack of 2.5 kVA with all accessories

complete as required shall be provided inside the panel. The rate shall include all

civil works such as foundation pad, grouting etc.

A. One(1) incoming feeder shall have the following features:

a. HT Breaker Type-

Indoor switchgear with fully interlocked, electrically operated draw out type, trip

free,VCB motor operated spring charged stored energy mechanism circuit

breaker with electrical releases, antipumping relay, complete with instruments,

relays and all associated auxiliaries, and with pad lockable automatic safety

shutters for power disconnect spouts, earth switch with suitable interlock with test

terminal block etc. Closing coil, shunt trip coils and indication ckt shall be suitable

b. Rated continuous current- 630A

c. Rated operational/ insulation voltage- 11/ 12kV

d. Short Circuit interrupting rating-350MVA

c. Rated short circuit level- 21.0 kA symmetrical for three (3) seconds.

d. Rated breaking current- 21.0 kA symmetrical

e. Power frequency withstand voltage - 28 kVp for 1 minute

f. Impulse withstand voltage- 75 kV at 1.2 x 50 microsecond wave crest.

g. Vacuum Bottle short time capacity-26.3 kA

h. Service Life (Designed)- 100 operations at short circuit

i. Electrical/ Mechanical closing / Tripping

j. Anti-pumping relay

k. Trip circuit supervision relay

l. Over current and earth fault self powered IDMT relay with instantaneous high set

element range 50 – 200% for outer poles and 20-80% for middle pole.

m. 110 V DC spring charging motor.

n. Indication for ON/ OFF/ SPRING CHARGED

o. Suitable number of NO/ NC contacts

p. 230V, 50Hz. Space heaters with fuse and ON/OFF toggle switch

q. 3 Nos. Cast resin CTs of dual ratio 60 - 30 / 5-5 Amps CL:1, 5P10, 15 VA.

r. 3 Nos. Cast resin drawout type PTs 11 kV / √3 / 110 √3, class 1, 100 VA

s. Cable termination space to be suitable for 1R (3C x 185) Sq.mm. 11kV armoured

XLPE cable, complete with cable sealing kit, push on type

B. Two (2) Outgoing feeder shall have the following features:

a. HT Breaker Type-

Indoor switchgear with fully interlocked, electrically operated draw out type, trip

free,VCB motor operated spring charged stored energy mechanism circuit

breaker with electrical releases, antipumping relay, complete with instruments,

relays and all associated auxiliaries, and with pad lockable automatic safety

shutters for power disconnect spouts, earth switch with suitable interlock with test

terminal block etc. Closing coil, shunt trip coils and indication ckt shall be suitable

b. Rated continuous current- 630A

c. Rated operational/ insulation voltage- 11/ 12kV

d. Short Circuit interrupting rating-350 MVA

c. Rated short circuit level- 21.0 kA symmetrical for three (3) seconds.

d. Rated breaking current- 21.0 kA symmetrical

e. Power frequency withstand voltage-28 kVp for 1 minute

f. Impulse withstand voltage- 75 kV at 1.2 x 50 microsecond wave crest.

g. Vacuum Bottle short time capacity-26.3 kA

h. Service Life (Designed)- 100 operations at short circuit

SL. DESCRIPTION OF ITEMS UNIT QTY Rate Amount (Rs.)

i. Electrical/ Mechanical closing / Tripping

j. Anti-pumping relay

k. Trip circuit supervision relay

l. Over current and earth fault self powered IDMT relay with instantaneous high set

element range 50 – 200% for outer poles and 20-80% for middle pole.

m. 110 V DC spring charging motor.

n. Indication for ON/OFF/SPRING CHARGED

o. Suitable number of NO/ NC contacts

p. 230V, 50Hz. Space heaters with fuse and ON /OFF toggle switch

q. 3 Nos. Cast resin CTs of dual ratio 40 - 20 / 5-5 Amps CL:1, 5P10, 15 VA.

r. 3 Nos. Cast resin drawout type PTs 11 kV / √3 / 110 √3, class 1, 100 VA

s. Cable termination space to be suitable for 1R (3C x 185) Sq.mm. 11kV armoured

XLPE cable, complete with cable sealing kit, push on type

All CTs & PTs in the incoming and outgoing shall be verified, approved and

calibrated as per the requirement of State Electricity Board.

HT Panel as described above SET 1 1823808.00 1823808.00

2 11kV DRY TYPE TRANSFORMER

1.1 Design, fabrication, assembling, wiring, supply, testing at works, packaging,

forwarding to site and supervising the testing & commissioning of 400 kVA, 3

phase, 11/ 0.433 kV Cast Resin indoor Dry type IP 33/34 Transformer copper

wound with Dyn 11 connection and neutral brought out for earthing as per

following specification and as per general and technical specification as required

complete. The transformer shall be provided with (–) 15% and (+) 5% On load tap

changer on HT side, remote tap changing circuit and inbuilt automatic voltage

regulator. HT side cable termination box shall be suitable for 11 kV, 3 C x 185 sq.

mm XLPE cable and LT side terminal box shall be suitable for termination of

suitable size AL cable. The transformer shall be supplied with all standard fitting

viz thermistors for Alarm and Trip, winding temperature relay unit with Alarm and

trip, lifting lugs, earthing studs and marshlling box, etc. complete in all respect as

required as per specification.

The transformer shall have the following specification:

a Rating: 11/ 0.433kV

b kVA rating: 400kVA

c Percentage impedance: 5.0% (+/-5%)

d Rated Primary system Voltage: 11 kV, 3 phase

e Rated Secondary system voltage (Center tap): 0.433 kV

f Highest Primary system Voltage: 13 kV, 3 phase

g Rated Secondary system voltage (Center tap): 0.459 kV

h Frequency: 50 Hz.

i Vector grouping: Dyn 11

j Cooling: AN cooled

k HT system fault level: 350 MVA(assumed)

l System Neutral Earthing for HV System: Non effectively Earthed

m System Neutral Earthing for LV System: effectively Earthed

n Impulse withstand voltage: For 11 kV: 75 kV

o Power frequency withstand voltage: 28kV

p Tap changing option: On load tap changer on HV side

q Tap changing range: +5% to -15% in steps of 1.25% each

r Transformer terminal box:

i. HV- Cable termination box to be suitable for 1R (3Cx185) Sqmm 11kV

armoured XLPE cable.

ii. LV- Cable termination box to be suitable for appropriate size 1.1kV armoured

400 kVA dry type transformer with OLTC (On Load Tap Changer) as described SET 2 2158172.80 4316345.60

1.2 The transformers as described in item no. 1.1 above shall be provided with

automatic on load tap changer panel suitable for remote operation to change the

transformer tapping in automatic and manual mode as per following specification

and as per general and technical specification as required complete. Automatic

voltage regulating relay to be provided with digital type tap position indicator for

auto operation. The panel shall be IP 54 free standing, floor mounted type. The

control circuit shall be suitable for master-slave operation for working in auto

The RTCC panel shall have the following :

a Digital tap position indicator

b Upper and lower limit indicator

c 433V/110V PT for LV sensing for AVR

SL. DESCRIPTION OF ITEMS UNIT QTY Rate Amount (Rs.)

d 0-500V Digital Voltmeter with selector switch

e 230V, 50Hz. Space heaters with fuse and ON/OFF toggle switch

f Rectfier for DC supply

g Tap changer isolation switch

h Tap changer in progress lamp

i Auto/ manual selector switch

RTCC Panel for 11 kV dry type transformer with OLTC as described above SET 2 182380.80 364761.60

3 Supply and fixing in position the approved “Shock Treatment Charts” written in No. 6 5319.81 31918.86

English and Local Language. These charts shall be framed in teak wood frame

and covered with glass.

4 Supply and fixing in position the fire extinguishers carbon-di-oxide type 4.5 Kgs No. 12 5026.60 60319.26

5 Supply and fixing of in position the fire extinguishers dry chemical power (ABC) 5 No. 12 5361.71 64340.51

6 Supply and fixing of in-position the fire extinguishers dry chemical power (ABC) 2 No. 12 3351.06 40212.75

7 Supply and fixing in position the best quality Danger Boards of approved shape No. 18 2136.30 38453.39

and size as specified by Local Electricity Authorities written in English & Local

8 Supplying of fixing in position 1.8 m length 0.9 m wide & of sufficient thickness, SET 4 4835.59 19342.36

Electrical grade Rubber mats of approved make and as per Electrical rule.

9 Supply of fire buckets 5 No. in each set duly filled with fine sand and fixed on an SET 3 14828.48 44485.43

angle iron frame as per requirement of local authorities. Fire buckets shall be

painted red from outside and white from inside with additional handle at the

bottom and suitable for outdoor installation.

10 Supply and fixing position the approved single line diagram framed in 1000 x 800 No. 6 837.77 5026.63

mm size glass frame and installed in main switch room.

11 Supply of First Aid box of approved make as per specification. No. 3 3351.06 10053.19

12 Supply of tool kit with 1 pair 11 KV rubber hand gloves of approved make. Set 2 3351.06 6702.12

Rate/ amount should include the following

The professional charges for liason work and departmental procedures required

for the above said work .

The work shall include the following:

a. Complete liasoning with Supply Company and electrical inspectorate.

b. Obtaining the feasibility report and spot inspection, etc.

c. Obtaining sanction of H.T. connection of 1000 KVA Transformer.

d. Preparation and submission of all statutory drawings to Supply Company and

electrical inspectorate.

e. Obtaining necessary approvals and submitting to the clients.

f. Arranging for the service from the Supply Company.

g. Any other works related to Supply Company and Electrical inspectorate.

TOTAL CARRIED TO SUMMARY 6825769.68

PART-2: HV CABLES

1 Supplying and laying following size 11 kV grade XLPE (E) aluminium conductor

armoured cables laid over MS supports in existing trenches.

a. 3 C x 185 sq.mm 11 kV XLPE (E) cable RM 80 2050.85 164,068.26

2 Supplying and making cable end terminations for the following size of 11 kV

grade, XLPE (E) aluminium conductor armoured cable including termination kit

complete heat shrinkable sleeve etc.

a. 3 C x 185 sq.mm 11 kV XLPE (E) cable No. 6 2891.97 17,351.83

3 Supplying, laying GI sleeves of following sizes:

SL. DESCRIPTION OF ITEMS UNIT QTY Rate Amount (Rs.)

4 Supplying and laying of following 1100 volts grade PVC insulated sheathed

copper conductor armoured control cables in existing trenches cables trays,

clamped on wall with suitable saddles, fixing bolts, including testing and

a. 7 Core 2.5 sq mm PVC insulated copper conductor armoured control cables RM 50 663.51 33,175.52

5 Cable end termination of the following PVC insulated sheathed aluminium

conductor armoured cables of 1100 volt grade including supplying and fixing of

crimping lugs. Double compression glands, cable sockets etc as required.

a. 7 Core 2.5 sq.mm Control cable No. 6 418.88 2,513.28

TOTAL CARRIED TO SUMMARY 248022.60

TOTAL (PART 1 + 2) 7073792.28

AC SYSTEM (HVAC WORKS)

SL.NO DESCRIPTION UNIT TOTAL RATE AMOUNT

NON SCHEDULE ITEMS

A. Supply of Split type AC Uint with Filter Clean Indicator, Super fine

Mesh Filter, Stepless Compressor Control, Penta sensor, 100%

Cooling capacity at 43°C

1TR 3 Star Inverter

Tropical Rotary Compressor, 230 V, 425 CFM Air Flow 4 38,768.80 155,075.20

1.5TR 3 Star Inverter

Tropical Rotary Compressor, 230 V, 530 CFM Air Flow 4 44,551.92 178,207.68

2.0 TR 3 Star Inverter

Tropical Twin Rotary Compressor, 230 V, 620 CFM Air Flow 16 57,290.24 916,643.84

4 Installation and Commissioning charge for Split AC Nos. 24 2,992.02 71,808.58

7 Copper Cable Rmt 288 200.93 57,867.26

Supply and installation of Readymade Angels and Brackets with

corrosion resistance paint 1,114.12 26,738.88

FIRE MANAGEMENT SYSTEM

Sl. No. Description Unit Quantity Rate Amount

(NON SCHEDULE ITEMS)

A FIRE DETECTION AND ALARM SYSTEM

FIRE DETECTION AND ALARM SYSTEM - ANALOG ADDRESSABLE SYSTEM

1 MANUAL CALL POINT

Supply, installing, testing & commissioning of addressable Manual

call point (Pull station-double action).

2 FAULT ISOLATOR

Supply, installing, testing and commissioning of addressable type

Fault Isolators for isolating shorted, de wired and loose circuits

between two successive fault isolators with automatic resetting

3 RELAY CONTROL MODULES

Supply, installing, testing and commissioning of addressable and

automatic commandable Relay control modules.

4 CONTROL MODULES

Supply, installing, testing and commissioning of addressable and

automatic commandable control modules.

5 MONITOR MODULES

Supply, Installation, testing and commissioning of Addressable

Monitor modules.

6 RESPONSE INDICATOR

Supply, installation, fixing, testing and commissioning of Response

Indicator cum lamp assembly mounted on walls/ partitions, surface/

recessed etc. in dust tight enclosure, including chase cutting

complete as required.

7 STROBES CUM HOOTERS

Supply, installation, testing and commissioning of Strobes cum Dual

tone hooters with minimum of 110cd and 93 db complete as Nos. 8.00 3198.10 25584.83

8 FIRE ALARM CONTROL PANEL

Supply, installting, testing and commissioning of Microprocessor

based intelligent and electronically addressable, modular,

expandable, networkable, loops as given below (each loop consist of

159 detector & 159 devices or as per the approved OEM) Fire Alarm

Control Panel with minimum 6 inch/ 640 character LCD display,

multiple access levels, event history file in non-volatile memory

(EEPROM). The panel shall support programmable relays controlled Nos. 1.00 638903.38 638903.38

by powerful Boolean logic equation. The panel shall have 240 volts

AC power supply, automatic battery charger, 24 volts, sealed lead

acid maintenance free batteries sufficient for 24 hours normal

working and then be capable of operating the system for 60 minutes

during emergency condition. The panel shall be UL listed 9th Edition

(With Networking Card Compatible to Fiber Optic Cable)

2 Loop Fire alarm control panel

Sl. No. Description Unit Quantity Rate Amount

9 WIRES IN CONDUITS:

Supply & laying of, 2x1.5 sq.mm 450/ 750V grade FR-LSH PVC

insulated, un-sheathed copper conductor wire including

a. terminations, connections & all labour and material etc.complete as Meter 350.00 57.96 20286.00

required (For fire detection signal, for fire loop, for speakers, for tele

Providing and fixing in position of MS conduit including bends,

junction boxes, pull boxes, GI pull wire including necessary civil work

c. such as chase cutting, chipping, making good for recessed conduiting

or clamping on surface with saddles, clamps etc. for surface

B. FIRE FIGHTING SYSTEM

1 Providing, laying, testing & commissioning of 'C' class heavy duty MS

pipe conforming to IS 3589/IS 1239 including Welding, fittings like

elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the

pipe on the wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel paint of required

shade complete as required :

2 Providing, installation, testing and commissioning of non-return valve

of following sizes confirming to IS: 5312 complete with rubber gasket,

GI bolts, nuts, washers etc.as required :

3 Supplying, fixing, testing and commissioning of butterfly valve of PN

1.6 rating with bronze/gunmetal seat duly ISI marked complete with

nuts, bolts, washers, gaskets conforming to IS 13095 of following

sizes as required :

4 Providing, installation, testing and commissioning of stainless steel Y-

strainer fabricated out of 1.6 mm thick stainless steel, Grade 304,

sheet with 3 mm dia holes with stainless steel flange.

5 Supplying and fixing first-aid Hose Reel with MS construction spray

painted in post office red, conforming to IS 884 complete with the

following as required.

20 mm nominal internal dia water hose thermoplastic (Textile

reinforced) type -2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve &

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal

valve & M.S. Pipe and socket.

Sl. No. Description Unit Quantity Rate Amount

6 Supplying, installation, testing and commissioning of electric driven

terrace pump suitable for automatic operation and consisting of

following, complete in all respects, as required: (Terrace Pump)

(a) Horizontal type, multistage, centrifugal, split casing pump of cast

iron body & bronze impeller with stainless steel shaft, mechanical

confirming to IS : 1520

b) Suitable HP squirell cage induction motor TEFC type suitable for

operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of

protection for enclosure, horiziontal foot mounted type with Class-'F'

insulation, conforming to IS-325.

(c) M.S.fabricated common base plate, coupling, coupling guard,

foundation bolts etc.as required.

(d) Suitable cement concrete foundation duly plastered and with anti

vibration pads.

7 Providing & fixing of pressure switch in M.S. pipe line including

connection etc. as required. 4 6,755.82

8 Providing & fixing swinging type hose reel drum fabricated from 14

SWG CRCA sheets painted with red color stove paint 2 coats over 1

coat of primer with 30 m long 20 mm dia rubber hose pipe with 10kg /

sqcm working pressure with GM shut – off nozzle of 5 mm outlet

fixed on wall with dash fasteners, 25 mm dia valve etc.as required

9 Providing and Fixing M.S. hose box with lockable arrangements to

accommodate 2 RRL hose of 15 m length and one branch pipe

painted white inside and red outside with one key.

Capacity 4.5 kg. ISI marked Each 20 8561.34 171,226.72

10 Providing and fixing mechanical foam type ( ISI marked ) fire

extinguisher consisting of welded MS cylindrical body, squeeze, lever

discharge valve, high pressure discharge hose, discharge nozzle,

suspension bracket ISI marked finished externally with red enamel

paint and fixed to wall with brackets with internal charger .

Capacity 9 liters Each 20 3399.35 67,987.08

11 Providing & fixing water Co2 ( ISI marked ) extinguisher including all

accessories with wall bracket with rawl plug.

Capacity 9 liters. Each 10 3155.60 31,556.00

12 Providing & fixing dry powder extinguisher consisting of welded MS

cylindrical body, with discharge valve, nozzle and CO2 cartige and

hanging arrangement complete

Capacity 5 kg. ISI marked Each 10 3735.20 37,352.00

DESIGN, drawing and SITC OF SIGNAGE

NO. ITEM DESCRIPTION QTY UNIT RATE AMOUNT

(NON SCHEDULE ITEMS)

1 Sign Typology for EXTERNAL SIGNAGE

1.1 TS - Totem Signs at Main entry Gate (18'6" x 4'6") 1 Nos. 360640.00 360640.00

Providing, Fixing & Preparing Graphics and Artworks for Tri-lingual Single Sided

Totem Sign of size 18'-6" x 4'-6" at gates. The existing structure between the two

column shall be modified as per design i.e. brick wall raised by 4'-6" and shall be

clad in 20mm thk. black granite. All graphics etched and coulour-filled as per

approved artworks, with transportation and installation at site complete.

Providing, Fixing & Preparing Graphics and Artworks for Single Sided Bilingual Site

Map of size 3' x 7', fabricated as per approved drawing, using 304 grade SS

channels, 3" x 2" x 2mm thk., of size 35" width x 8'-6" height, embedded 18" verticaly

into ground with proper foundation in cement concrete in 1:2:4, with sign panels in

20mm thick Black Granite, (with approved artworks and graphics etched and color

filled) bolted over SS framework with necessary hardware and tools required for

proper fixing for the same in position, with transportation and installation at site

2 Sign Typology for INTERNAL SIGNAGE

2.1 DF - Fixed Door Signs (16" x 8") 15 Nos. 5987.52 89812.80

Providing, Fixing & Preparing Graphics & Artworks for Trilingual ID-2 Signs of size

14" x 6", in 5mm thk. Clear Acrylic, laser cut to appropriate size and shape, with all

graphics 'flat-bed' printed directly onto acrylic surface in reverse as per approved

artworks, fixed to existing surface using studs/spacers/ brackets or 3M double sided

tapes whichever appropriate as per site conditions, using necessary hardware and

tools, with transportation and installation at site complete.

eg. Seminar room, Museum, Cafeteria, office Room, Lift No. & name, Library,

Electrical Room, AHU etc.

2.2 WF - Wayfinding Signs (48" x 12") 12 Nos. 27167.84 326014.08

Providing, Fixing & Preparing Graphics & Artworks for tri-lingual Suspended

Directional Signs of size 48" x 12", in 5mm thk. Clear Acrylic, laser cut to appropriate

size and shape, with all graphics 'flat-bed' printed directly onto acrylic surface in

reverse as per approved artworks, fixed to existing surface using studs/ spacers/

brackets/ suspension mechanisms or 3M double sided tapes whichever appropriate

as per site conditions, using necessary hardware and tools, with transportation and

installation at site complete.

Mostly in Corridors

TOTAL FOR SIGNAGE 1245298.88

SITC OF EQUIPMENT

Description Unit Quantity Rate Amount

Equipment (COCOON TO YARN)

Solar Unnati Tasar (4 spindle) Machine &

Solar Unnati Tasar (2 spindle) Machine &

3.0 Re-reeling charkha 8 ends & installation Nos. 10.00 48737.92 487379.20

4.0 Spinning / Deflossing (pedal) & installation Nos. 10.00 12570.88 125708.80

5.0 Bobbin winding (32 spindle) & installation Nos. 2.00 146574.40 293148.80

6.0 Twisting (80 Spindle) & installation Nos. 1.00 273056.00 273056.00

7.0 Re-reeling + twisting (20 spindle) & installation Nos. 2.00 144771.20 289542.40

8.0 Cone making machine & installation Nos. 1.00 1003352.00 1003352.00

9.0 Book machine (yarn) & installation Nos. 10.00 6780.03 67800.32

10.0 Boiler & installation Nos. 1.00 407008.00 407008.00

Hot Chamber with Conveyor system 2T

Equipment Post Yarn (YARN TO WEAVING)

Sun Kharga- Solar operated Loom with

Installation, Testing and commissioning

Handlooms with accessories with

Installation, Testing and commissioning

15.0 Dobby attachment & installation Nos. 1.00 13833.12 13833.12

16.0 Jacquara (400 Hooks) & installation Nos. 1.00 58990.40 58990.40

17.0 Warping machine & installation Nos. 2.00 276662.40 553324.80

Digital Printing machine & Accessories with

Installation, Testing and commissioning

Padding process with Installation, Testing and

Description Unit Quantity Rate Amount

Steamer with Installation, Testing and

Industrial washing machine with Installation,

Testing and commissioning

Rinsing machine with Installation, Testing and

Drying machine with Installation, Testing and

Ironing machine with Installation, Testing and

Other Equipment

26.0 Desktop Computer (all in one type)

9th Generation Intel® Core™ i7 processor

Windows 10 Pro 64

16 GB DDR4-2666 SDRAM (1 X 16 GB)

1 TB PCIe® NVMe™ SSD

Intel® UHD Graphics 630

Min screen size 60. 45 cm

Note: Cost for all Items are inclusive of 5 years AMC (including defect liability period) with spare and Labour,

imparting necessary training to Owner's personnel and supply of opearational manuals in triplicate from

SUPPLY AND INSTALLATION OF FURNITURE WORKS

SNO. PARTICULARS QTY UNIT RATE AMOUNT

HOSTEL CUM GUEST HOUSE

SINGLE BED 7' x 3' in 18/19 mm THICK CALIBRATED BWP PLY & 0.8 mm LAMINATE,

1 SIDE TABLE SIZE 500 w 400 d 450 h & WARDROBE 18/19 mm THICK CALIBRATED BWP 4 SET 83720.00 334880.00

PLY & 0.8 mm LAMINATE OF SIZE 800 w 600 d 2100 h

MEDIUM BACK CHAIRS REVOLVING AND TILTING WORKING POSITION LOCK HYDRALIC

2 GASLIFT , 5 PRONGED NYLON BASE NON SAGGED PU FOAM UPHOSTERED PLY SEAT 4 PCS 6440.00 25760.00

ERGONOMIC MESH BACK REST IN POWDER COATED METAL FRAME .

WROUGHT IRON DOUBLE DECK BED MADE OF 50 mm x 50 mm ,50 mm x 25 mm 19mm (

ROUND ) & 25m X 35mm CRCA MS 1.6mm PIPE .60 MICRON POWDER COATING BED

3 SIZE H 1950 mm W 900 mm L 1950mm HEAD SIDE & LEG SIDE GROUND OF THE BED 300 40 PCS 45080.00 1803200.00

mm HEIGHT BETWEEN 2 COTS 1050 mm STAIR WIDTH 300 mm WITH BONDED FOAM

METAL POWDER COATED STORAGE 2 DRAWER SIZE 300mm x 450 mm x 600 mm 18

4 GUAGE CRCA MS SHEET EPOXY POLYSTER 50 MICRONS POWDER COATED

DINING HALL – 6 SEATER TABLE SIZE 5' x 2'6" IN MS FRAME 60 MICRON POWDER

COATING AND WOODEN TOP WITH ABS CAFE CHAIRS

CRECHE - 4 MESH WORK CHAIRS REVOLVING AND TILTING WITH 3 SEATER LEATHERITE

COMMON ROOM - 2 SINGLE LEATHERITE SEATER SOFA WITH 1 No GLASS CENTRE

7 TABLE 3' X 2'

5 Pcs REVOLVING AND TILTING MESH CHAIRS & ARROW BASE GLASS TOP TABLE 1.5 M

MEDIUM BACK CHAIRS REVOLVING AND TILTING WORKING POSITION LOCK HYDRALIC

9 GASLIFT , 5 PRONGED NYLON BASE NON SAGGED PU FOAM UPHOSTERED PLY SEAT 12 PCS 6440.00 77280.00

ERGONOMIC MESH BACK REST IN POWDER COATED METAL FRAME .

WORK DESK IN 25 MM THICK PRE LAMINATED PARTICLE BOARD 17 MM MODESTY 4' X

10 2' TOP WITH 3 DRAWERS 400 MM W X 450 D 680 H 3 PCS 19320.00 57960.00

DESIGN AND TRAINING CENTRE

RECEPTION - 2 +1+1 SEATER SOFA IN WOODEN FRAME WITH BELTS AND FOAM PU

11 LEATHERITE UPHOLSTERED AND WOODEN TEAK WOOD CENTRE TABLE AS PER 2 SET 103040.00 206080.00

CAFETERIA – 6 SEATER TABLE 6' x 3' IN MAHOGANY WOODEN FRAME 18 mm PLY

CALIBRATED BWP PLY AND 5mm THICK VENEER TOP WITH MAHOGANY WOOD

12 DINNING CHAIRS UPHOLSTRY IN 40 DENSITY FOAM IN SEAT 28 DENSITY IN BACK & 5 SET 103040.00 515200.00

MEETING ROOM – 5 Pcs REVOLVING AND TILTING MESH CHAIRS & CHROME FINISH

13 ARROW BASE 1.5M DIA 8 mm THICK GLASS TOP TABLE 1 SET 39928.00 39928.00

MEDIUM BACK CHAIRS REVOLVING AND TILTING WORKING POSITION LOCK HYDRALIC

14 GASLIFT , 5 PRONGED NYLON BASE NON SAGGED PU FOAM UPHOSTERED PLY SEAT 12 PCS 6440.00 77280.00

ERGONOMIC MESH BACK REST IN POWDER COATED METAL FRAME .

OFFICE - WORK DESK IN 25 MM THICK PRE LAMINATED PARTICLE BOARD 17 MM

15 MODESTY 4' X 2' TOP WITH 3 DRAWERS 400 MM W X 450 D 680 H 3 PCS 19320.00 57960.00

TRAINING ROOM – 10 Pcs REVOLVING AND TILTING MESH CHAIRS & ARROW BASE

16 GLASS TOP TABLE 4.0 M X 2.0M 1 SET 39928.00 39928.00

MEETING ROOM – 5 Pcs REVOLVING AND TILTING MESH CHAIRS & CHROME FINISH

17 ARROW BASE, 8 mm THICK GLASS TOP TABLE SIZE 6' X 6' 1 SET 39928.00 39928.00

LABOUR REST ROOM - 2 +1+1 SEATER SOFA IN WOODEN FRAME WITH BELTS AND

18 FOAM PU LEATHERITE UPHOLSTERED AND WOODEN TEAK WOOD CENTRE TABLE AS 1 SET 103040.00 103040.00

NOTE: SHOP DRAWINGS FOR ALL FURNITURE PREPARED BY MANUFACTURER (AS PER LIST OF APPROVED

MAKES) TO BE SUBMITTED FOR APPROVAL OF EMPLOYER. COLOUR / SHADE OPTIONS WILL BE AS PER

CHOICE OF EMPLOYER.