AUGMENTATION OF SECURITY OF STORAGE AREA VEHICLE INTEGRATED BAY III (VIB III) AT INS KALINGA, VISAKHAPATNAM

Amount

SCHEDULE "A" PART - I [CIVIL WORKS]

Excavating over areas, not exceeding 1.5 m in depth and getting out soft / loose soil, complete all as specified and as directed by the Engineer-in-Charge.

Excavating over areas, depth exceeding 1.5 m but not exceeding 3 m and getting out hard / dense soil, complete all as specified and as directed by the Engineer-in-Charge.

All as per Item No.1.002 above, but depth exceeding 3 m but not exceeding 4.5 m.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations, pile cap, beams, shafts, wells, manholes, pier holes, laying of under ground cables or pipe etc., not exceeding 10 sq m on plan and getting out in soft / loose soil, complete all as specified and as directed by the Engineer-in-Charge.

Excavation in trenches not exceeding 1.5 m wide and depth exceeding 1.5 m but not exceeding 3 m for foundations, pile cap, beams, shafts, wells, manholes, pier holes, laying of under ground cables or pipe etc., not exceeding 10 sq m on plan and getting out in hard / dense soil, complete all as specified and as directed by the Engineer-in-Charge.

Returning, filling in including, spreading, leveling, watering and well ramming in layers not exceeding 25cm thick as in any type of soil, complete all as specified and as directed by the Engineer-in-Charge. Note: (i) 10 % Deduction shall be made from total computed volume of filling to cater in bulk in respect of mechinery used for ramming (ii) Compacted thickness wiil be measured for the payment purpose.

Excavating in post holes (or similar holes) as in soft / loose soil, each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 m, where directed and making good surface, complete all as specified and as directed by the Engineer-in-Charge.

Surface Dressing not exceeding 15 cm deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-In-Charge.

Site Clearance as in soft / loose soil, complete all as specified and as directed by Engineer-In-Charge. Note: The unit rate shall be deemed to be included for rubbish / useless material disposed off to outside MD land and useful material shall be stacked

Material and labour for Coarse sand filling in rain water pit, laid in layers not exceeding 15 cm thick, spread, levelled, and blinded with earth and rammed including watering, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Sand filling under floors or in foundations including watering and consolidation, complete all as specified and as directed by the Engineer-in-Charge.

Removing the excavated material (soil) to a distance exceeding 250m but not exceeding 500m and depositing where directed at a level not exceeding 1.5m above the starting point at a designated place, complete all as specified and as directed by the Engineer-in-Charge.

Removing the excavated material (soil) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point at a designated place, complete all as specified and as directed by the Engineer-in-Charge.

Removing the excavated material (soil) to a distance exceeding 1.5 km but not exceeding 5 km and depositing where directed at a level not exceeding 1.5m above the starting point at a designated place, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Loose filling with broken brick aggregates of gauge 80 to 150 mm in rain water harvesting pit, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Loose filling with broken brick aggregates of gauge 40 to 80 mm in rain water harvesting pit, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Hard core of gauge not exceeding 63 mm broken bricks deposited, spread, levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for hard core (broken stones or boulders) of gauge exceeding 63 mm but not exceeding 100mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Shingle filling in rain water harvesting pit, laid in layers not exceeding 15 cm thick, spread, levelled, and blinded with earth and rammed including watering, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Moorum/red bajri in floors or pavings, brought from outside MD land of any lead laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering, complete all as specified and as directed by the Engineer-in-Charge. Note: Measurements of the finished surface of moorum/red bajri filling shall be taken after consolidation and 10% deduction shall be made for increase in bulkage.

Material and Labour for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured), complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for pre construction anti termite treatment by treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for PCC 1:4:8 type D-2, by using 40mm graded granite stone aggregate, as in foundations, filling and mass concrete, underneath pile caps, capping beams, suspended floor, foundations, plinth beams, haunching and packing of pipes, etc., complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 75 mm thick PCC 1:3:6 type C-1 ( using 20mm graded granite stone aggregate), as in plinth protection , finished even and fair without using extra cement including making construction joints in 3 m interval and joint filled with sealing compound, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for PCC 1:3:6 type C-2, by using 40mm graded granite stone aggregate, as in foundations, filling and mass concrete, underneath pile caps, capping beams, suspended floor, foundations, plinth beams, haunching and packing of pipes, culvert, wing wall, return wall, curtain wall, apron, approach slab, etc., complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for PCC 1:4:8 type D-2, by using 40mm graded granite stone aggregate, as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases), complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for PCC 1:2:4 type B-2, by using 40mm graded granite stone aggregate, as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases), complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Reinforced Ready Mixed Cement Concrete of grade M-40 Design mix with admixture Auramix 400 of Fosroc or Smartcare maximo plast PX range of Asian Paints or equivalent, as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. and mass concrete and including handling, conveyance, erection with alignment in true position, finishing, complete all as specified and as directed by the Engineer-in-Charge.

All as per Item No. 1.030 above but as in bottom slabs / ramp deck slab/ floor slab /roof slab/ landings and steps/ balconies/ canopies/ shelves/ hard-standings.

All as per Item No. 1.030 above but as in chajjas.

All as per Item No. 1.030 above but as in beams/ floor beams/ roof beams/ cantilevers/ lintels over 1.5 m span.

All as per Item No. 1.030 above but as in columns/ pillars/ posts/ struts.

All as per Item No. 1.030 above but as in Staircase including steps (square of spandrill), string pieces, carriages, etc. Complete, any section, straight or winding, but excluding landings, RCC water tanks upto 1500 litres.

All as per Item No. 1.030 above but as in fins/ facias/ louvers/ parapets and railings exc 60 cm in height/balustrade and the like. Notes for Item Nos. 1.030 to 1.036: (i) Minimum cement content shall be 400 Kg per Cu.m .of concrete for M 40 using Portland slag cement with minimum slag content of 50% (fifty percent) (ii) Design mix shall be as per IS-456-2000. The size of aggregate shall not exceed 20 mm and slump shall be 50mm (+/-) 12mm and maximum water cement ratio 0.4. (iii) Unit rate shall be deemed to include for interalia for preliminary design mix and works test cubes. (iv) Reinforcement shall be measured and paid for separately. (v) In case cement content is increased beyond minimum content given during the design mix, no extra payment shall be admissible. (vi) Standard manufactured cover blocks as per IS should be used, Site cast cover blocks not to be used. (vii) Admixture to be mixed in RCC work shall be @ 0.6 % to 1 % by weight of cement or as given in approved design mix during execution of work. Make: Auramix 400 of Fosroc or Smartcare maximo plast PX range of Asian Paints or equivalent. The cost of the admixture shall be deemed to be included in the quoted rate.

Material and Labour for providing PCC 1:2:4 , type B0 using 12.5mm graded stone aggregate as in channel of drain, bottom of septic tank and coping, etc., finished even and smooth, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for providing PCC 1:2:4 , type B1 using 20mm graded stone aggregate as in coping including weathering, slightly rounded or chamfered and complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for factory made Autoclaved Aerated Concrete (AAC) block masonry exceeding 10 cm in width and setting in cement mortar 1:4, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for precast Reinforced Cement Concrete drain covers made out of cement concrete 1:2:4 type B1 using 20mm graded stone aggregate and set in cement mortar 1:4, complete all as specified and as directed by the Engineer-in-Charge. Note: Reinforcement shall be measured and paid separately

Material and Labour for Reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and as directed by the Engineer-in-Charge. Note: Reinforcement shall be measured and paid for separately.

Material and Labour for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Walling of squared rubble, regular coursed, well bonded, bedded and solidly hearted, built in CM(1:6), brought upto courses, complete all as specified and as directed by the Engineer-in-Charge.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, maximum depression on face from straight edge held against the dressed surface not exceeding 40mm (Granite or trap stone), complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platorms and like in cement mortar (1:4) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams,pile caps and similar work; vertical or to batter for flat rough finished surface of concrete, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Steel formwork to faces of walls , retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttressess, etc; vertical or to batter for flat fair finished surface of concrete, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) for flat fair surfaces of concrete, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Steel formwork to chullah hoods, chajjas, troughs and similar items including edges, RCC gutters, cat walk and similar items with fair finished surface of concrete, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Steel formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams, etc with fair finished surface of concrete, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Steel formwork to staircases with sloping or stepped soffits including risers and stringers (excluding landing) with fair finished surface of concrete, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Steel formwork to sides of pillars, posts, struts, piers, columns and stanchions having square, rectangular or polygonal shape with fair finished surface of concrete, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Steel formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exceeding 5cm but not exceeding 10cm wide, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing to new door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 200 mm long aluminium anodised, barrel tower bolts with plates, staples, of extruded section, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 150 mm long aluminium anodised, barrel tower bolts with plates, staples, of extruded section, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 100 mm long aluminium anodised, barrel tower bolts with plates, staples, of extruded section, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix aluminium alloy, anodised, sliding door bolt of 300 mm length,with hasp, staple (bolt type), and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix , 75mm size butt hinges, extruded aluminium alloy with with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix , 100mm size butt hinges, extruded aluminium alloy with with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 125mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 150mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix mortice lock, vertical type, brass, of size 100mm with 4 levers, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix floor door stopper of aluminium alloy body, and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix hat pegs, solid body, 125mm to 175 mm in set of three pegs, aluminium, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix MS framed work such as grills, gratings, etc., with end of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 290 Gde E-165, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for reinforcement in any situation using corrosion resistant TMT steel bars of grade FE-500D, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by the Engineer-in-Charge.

All as per Item No. 1.069 above but, 5 mm dia and over upto and including 10 mm dia, in stirrups, spacers and binders, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix powder coated aluminium frame for doors, windows, ventilators and shutters for doors and windows with extruded build up standard tubular and other section of approved make transparent or to required shade according to IS:1868 fixed with rawl plug and aluminium anodised screws or fixing with clips or with expansion hold fasteners including necessary filling up of gaps of junctions at top, bottom and sides with required PVC / neoprene felt, etc. Aluminium sections shall be smooth, rust free, straight mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading, panelling, aluminium anodised screws, complete all as specified and as directed by the Engineer-in-Charge. Note: Minimum thickness of powder coating shall be 50 micron.

Supply and Fix powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/ RM including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc., complete all as specified and as directed by the Engineer-in-Charge. Note: Minimum thickness of powder coating shall be 50 micron.

Supply and Fix powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/RM including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.), complete all as specified and as directed by the Engineer-in-Charge. Note: Minimum thickness of powder coating shall be 50 micron.

Supply and Fix anodised aluminium snap grid frame false ceiling consisting of 25 X 25 X 2mm aluminium angles and TEEs of size 25 x 25 x 2mm and 12mm thick gypsum board of size 595 X 595mm on aluminium grid, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for prioviding and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (where ever required) and filing the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessay accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Machine cut kota stone slab flooring 18 to 20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Kota stone slab 18 to 20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for 100 mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base, floor, path, pavings etc, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for 75 mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate), laid in panels in floors, finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for 75 mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate laid in panels in floors finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for glazed ceramic coloured / printed tiles in vertical surface 300mm x 450mm x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Virified Ceramic tiles of light shade, double charged, 8 to 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for factory made Cement concrete tiles 20cm x 20cm x 20 to 22mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors with grey cement and no pigment, and cut and polished, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Machine pressed rubber moulded coloured interlocking paver block with grey cement and pigment of any shape and size conforming to IS 15658-2006 of 80 mm thickness made out of M-40 Grade concrete, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for 15 mm thick screed bed or bedding layers in cement mortar 1:4, for laying floor finishes, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for rendering to fair faces of brick / concrete surfaces, 10 mm thick in cement mortar 1:3, surfaces finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge..

Material and Labour for rendering to fair faces of brick / concrete surfaces, 10 mm thick in cement mortar 1:6, surfaces finished even and smooth without using extra cement including plaster grooves of size 10 mm x 1 mm at junction of RCC work, complete all as specified and as directed by the Engineer-in-Charge..

Material and Labour for rendering 5 mm thick on fair faces of concrete surfaces of ceiling, soffits and sides of floors/roof beams and chajjas etc in cement mortar 1:3, finishing the surface even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for rendering on stone masonry surfaces, 15 mm thick (in two coats 10mm + 5mm) in cement mortar 1:4, finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for rendering 15mm (5mm thick over 10mm thick backing coat) thick on external faces of brick work or concrete surface in cement mortar 1:4, finishing the surface even and smooth without using extra cement mixed with water proofing compound on external coat of plaster, complete all as specified and as directed by the Engineer-in-Charge. Note: WPC shall be measured and paid for separately.

Material and Labour for Flush pointing to to random rubble masonry, uncoursed or brought upto courses in cement mortar 1:4, complete all as specified and as directed by the Engineer-in-Charge.

Supply only of Integral waterproofing compound, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for three coats of white washing on newly plastered ceiling surface including preparation of surfaces, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for two coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification including preparation of surface of wall, complete all as specified and as directed by the Engineer-in-Charge.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including preparation of surface of wall, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for preparation of new or unplastered surface of walls and applying two coats of cement based paint, over a coat of alkali resistant primer, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Sheet glass of 5.5 / 6 mm thickness, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq. m in each pane, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Sheet glass of 5.5 / 6 mm thickness, ordinary quality and glazing with oil putty in square exceeding 0.5 sq. m in each pane, complete all as specified and as directed by the Engineer-in-Charge.

Extra over sheet glass, ordinary quality, if sheet glass is ground or obscured or frosted, on one side, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Concrete bed with PCC (1:3:6) type C2 (using 40 mm graded stone aggregates) to drain pipes for 150 mm bore including packing under, and haunching against the sides of pipes after they are laid and tested, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Reinforced concrete pipes, class NP2, 150 mm dia, laid and jointed complete with collars, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Reinforced concrete pipes, class NP3, 150 mm dia, laid and jointed complete with collars, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Towel Ring of Stainless steel fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) , complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Liquid soap container of Stainless steel fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 105gms), complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Toilet paper holder, coloured, Stainless steel, box type, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Vitreous China wash basin, white, flat back, size 630mm x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets , complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Vitreous china Wash down water closet pan EWC (Pedestal pattern), white with 'P'or 'S' trap étc, (excluding flushing cistern and flush pipe) including plastic water closet seat, closed pattern with flat bottom cover, white in colour, mild steel chromium plated or aluminised hinging device, fixing bolts, etc , complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix PVC valveless, syphonic action type low level flushing cistern, 10 ltrs capacity, white with inlet ball valve, float and handle soft touch type including brackets, PVC flush pipe etc complete fixed with CP brass screws , complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe), complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix three layered Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 1000 Litres, hoisted and fixed in position all as specified in SSR Part I, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix three layered Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 2000 Litres, hoisted and fixed in position all as specified in SSR Part I, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix bib taps, cast copper alloy, fancy type, quarter turn, chromium plated, screwed down, screwed for iron pipe or for brass ferrule for 15 mm bore dia of pipe, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 15mm bore chromium plated pillar taps, fancy type, cast copper alloy with capstan heads, quarter turn, screwed down high pressure with or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

Supply and Fix stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, quarter turn, screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix PVC (SWR) 110mm bore pipes single socketed, ISI marked, in any length with rubber ring joints, laid in trenches or in floors or on walls, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix PVC (SWR) 75mm bore pipes single socketed, ISI marked, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix PVC (SWR) 110mm bore bends of any radius, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix PVC (SWR) 75mm bore bends of any radius, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 110mm PVC (SWR) WC connector bent type including jointing with solvent, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 110mm dia PVC (SWR) branch pieces, (single Y/T), equal or unequal, ordinary or inverted with oval access door including jointing with solvent, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 75mm dia PVC (SWR) branch pieces, (single Y/T), equal or unequal, ordinary or inverted with oval access door including jointing with solvent, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix, PVC(SWR) floor/Nahani trap 75mm size plain with grating including jointing to waste pipe with solvent cement, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix, Grating doom 100mm dia of PTMT (Minimum weight 25gms), complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix for Galvanised steel water tubing 15mm bore, medium grade conforming to IS:1239(Part -I), ISI marked, with all fittings (such as bends, tees, short pieces, connectors, elbows, reducers, union sockets,etc) and fixed to walls and ceilings or laid in floors, complete all as specified and as directed by the Engineer-in-Charge.

All as per item No.1.129 here-in-before but 20mm bore.

Supply and Fix PVC connection (high density) 15mm dia of length 450mm with PTMT nuts both ends with rubber washer, complete all as specified and as directed by the Engineer-in-Charge.

Cutting into existing manholes for 150 mm dia pipe connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix shower roses, cast copper alloy, fancy type, chromium plated, heavy pattern, 125mm dia, including jointing to steel pipe for 15mm bore inlet, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed by the Engineer-in-Charge

Rolling and consolidation formation surfaces in cutting by using power roller 8 to 12 tonne capacity, complete all as specified and as directed by the Engineer-in-Charge.

Forming 12 mm thick expansion joint filled with pre-formed bituminious filler and top 30mm primed and sealed with sealing compound Grade 'A' for 100 mm thick slab, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for forming embankments in fillings using approved moorum obtained from out side MD land of any lead including raising earth, spreading in layers not exceeding 30 cm thick, watering, rolling with power rollers to obtain standard proctor density not less than 95 percent under optimum moisture conditions and consolidations and finishing to required size, shape, camber, etc not exceeding 1.5 m height from base of moorum filling, complete all as specified and as directed by the Engineer-in-Charge. Note: Measurements of the finished surface of moorum/red bajri filling shall be taken after consolidation and 10% deduction shall be made for increase in bulkage.

Material and Labour for RCC spectic tank with upflow filters for 50 users including sludge chamber, excavation in any type of soil PCC (1:2:4) in foundation, brickwork in CM(1:4), RCC slab in M-25, plastering in CM(1:4) etc., complete all as specified and as shown on TD drawing No.TD - 236 sheet 1/1 dated 08/05/2017 and as directed by the Engineer-in-Charge.

Material and Labour for soakage well of size 1.80m dia and 3.00mt deep including all necessary earthwork in any type of soil, PCC (1:3:6) in foundation, brickwork in CM(1:4), RCC slab in M-25, filling with brick bats etc., complete all as specified and as shown on TD drawing TD - 202 dated 10-04-2012 and as directed by the Engineer-in-Charge.

Supply and Fix Cardiff Health Faucet (Cat No T9941A1 of Make Parryware or its equivalent as approved by GE) with and including connecting hose 2.0 Ft long (Cat No T991999 Make Parryware or its equivalent as approved by GE) and Jet angle valve Cat No (T 9914A1 Make Parryware or its equivalent as approved by GE) and hook fixed to wall, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terrace, etc., consisting of the following sequences of operations on RCC surfaces: (a) Roof slab shall be cleaned thoroughly and apply cement slurry @3 Kg/sqm. (b) Applying a cement plaster of 10 mm thickness in CM 1:4 mixed with water proofing compound finished smooth. (c) Clean the surfaces throughly and apply a coat of bitumen primer @0.4 Kg/ sqm. (d) Polymeric water proofing (Attatic poly propelene) membrane minimum 3 mm thick of weight not less than 3.5 kg/sqm shall be laid over the entire surface by torching method. ( e) Finally it shall be finished with a coat of bituminous aluminum paint @0.1 Kg/sqm.

Supply and Fix UPVC partition as per specification and section given in drawing No. DGNP/WD/2051-VB, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 20 mm dia Stainless steel curtain rod with decorative bracket including stops and roller, complete all as specified and as directed by the Engineer-in-Charge.

SUB TOTAL OF SCHEDULE "A" Part - I

SCHEDULE "A" PART - II [INTERNAL ELECTRIFICATION]

Material and labour for concealed point wiring on wall and surface on ceiling/roof with necessary fixing arrangements with PVC-FRLSH insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including white / ivory PVC conduit medium grade ISI marked not less than 20 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and Bakelite laminated sheet 3mm thick ISI marked for fixing of modular switches / sockets, fan regulators, wall mounting fittings, door bell & bulkhead etc with MS screw and cup washers including PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces for One light point controlled by one switch complete all as specified and as directed by the Engineer-in-Charge.

All as per item No. 2.01 here-in-above but for One light point controlled by two two way switches complete.

All as per item No. 2.01 here-in-above but for One fan (ceiling / Wall / Exhaust fan) controlled by one switch complete.

All as per item No. 2.01 here-in-above but for One light or one fan point controlled by MCB complete.

All as per item No. 2.01 here-in-above but for One 3 Pin socket outlet 5 amps socket on independent board complete.

All as per item No. 2.01 here-in-above but for One 3 Pin socket outlet 5 amps socket on same board with other switches complete.

All as per item No. 2.01 here-in-above but for One 3 Pin socket outlet 15 amps socket on independent board but with cables of size 2.5 sq.mm and earthing of size 2.5 sq.mm

Supply and Fix Ceiling rose, 3 terminal, 3 phase/PVC/polycarbonate, isolated body, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Modular Switch, flush type single pole, one way 5 Amp, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Modular Switch, flush type single pole, Two way 5 Amp, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Modular Switch, flush type single pole, One way 15 Amp, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Modular Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Modular Socket outlet 3 pin, 15 amp flush type, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix flush type Modular Socket outlet 2 in 1, 3 pin, 5A, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Fan step regulators, 120W, 5 steps, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix SPN MCB of 6-32A capacity, C curve, 10 kA capacity, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix Isolator TP of capacity 32 to 63A, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix 415V 50 Hz 4P MCCB of 125A, 16 KA, complete all as specified and as directed by the Engineer-in-Charge.

All as per above Item No. 2.18 but of Isolator 4P of 63A Capacity, complete all as specified and as directed by the Engineer-in-Charge.

Supply, Fix , Test and Commissioning of MCB SP 240 volt 6 Amp to 40 amp 10 KA capacity having C-curve characteristics connected with suitable lugs, complete all as specified and as directed by the Engineer-in-Charge

Supply, Fix , Test and Commissioning of MCB SP 240 volt 6 Amp to 40 amp 10 KA capacity having B-curve characteristics connected with suitable lugs, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix double door metallic sheet metal enclosure for DB when MCBs to be used SPN 8 ways, 240 V with 200Amps rated bus bar complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fix double door metallic sheet metal enclosure for DB MCCB as incomer when MCBs to be used TPN 8 ways, 415 V with 200Amps rated bus bar complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires, complete all as specified and as directed by the Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60cm × 60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead 4.0mm dia GI wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 of SSR Part I, including excavation/earth work in any strata, adequate quantity of charcoal and common salt, PCC chamber with RCC 1:2:4 type B1 40mm thick cover slab with suitable handle and angle iron frame of suitable size to fix the cover, with 20mm bore GI pipe light grade for watering with funnel, wire mesh and 15mm bore GI pipe medium grade for GI wire protection and 4mm GI earth wire, including testing on completion, complete all as specified and directed by the Engineer-in-Charge. Note: Earth wire will be measured after 7.5mtr from the earth strip or earth testing terminal block whichever is lesser under relevant item.

All as per Item No. 2.24 above, but using galvanised iron strip 25 × 4mm earthing lead and 40mm bore GI pipe medium grade as protection pipe.

All as per Item No. 2.24 above, but using galvanised iron strip 32 × 6mm earthing lead and 50mm bore GI pipe medium grade as protection pipe.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire, complete all as specified and as directed by the Engineer-in-Charge.

All as per Item No. 2.27 above, but 32 x 6mm dia galvanised iron strip or steel wire.

All as per Item No. 2.27 above, but 25 x 4mm galvanised iron strip.

Material and Labour for sub main wiring including adequate size of conduit pipe and fittings with two single core PVC-FRLSH insulated unsheathed multistranded copper conductor cable of size 2.5 sqmm drawn in and including PVC rigid conduit with 2.5 Sqmm PVC-FRLSH insulated unsheathed multistranded copper conductor as a continuous earth wire, complete all as specified and as directed by the Engineer-in-Charge. Note : Two single core cable, one run of earth copper conductor and one run of PVC conduit shall be measured and paid as one unit length.

Material and Labour for sub main wiring with two single core PVC-FRLSH insulated unsheathed multistranded copper conductor cable of size 4 sqmm drawn in and including suitable size of PVC rigid conduit and accesories with 4 Sqmm PVC-FRLSH insulated unsheathed multistranded copper conductor as a continuous earth wire , complete all as specified and as directed by the Engineer-in-Charge. Note : Two single core cable, one run of earth copper conductor and one run of PVC conduit shall be measured and paid as one unit length.

Material and Labour for sub main wiring with two single core PVC-FRLSH insulated unsheathed multistranded copper conductor cable of size 6 sqmm drawn in and including suitable size of PVC rigid conduit and accesories with 6 Sqmm PVC-FRLS insulated unsheathed multistranded copper conductor as a continuous earth wire, complete all as specified and as directed by the Engineer-in-Charge. Note : Two single core cable, one run of earth copper conductor and one run of PVC conduit shall be measured and paid as one unit length.

Material and Labour for sub main wiring with two single core PVC-FRLSH insulated unsheathed multistranded copper conductor cable of size 10 sqmm drawn in and including suitable size of PVC rigid conduit and accesories with 10 Sqmm PVC-FRLS insulated unsheathed multistranded copper conductor as a continuous earth wire , complete all as specified and as directed by the Engineer-in-Charge. Note : Two single core cable, one run of earth copper conductor and one run of PVC conduit shall be measured and paid as one unit length.

Supply and laying of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 6 sq. mm 4 core, complete all as specified and as directed by the Engineer-in-Charge. Note: Excavation and earthwork, protection of cable, etc., if required, shall be measured and paid separately.

All as per Item No. 2.34 above, but cross-sectional area 10 sq. mm 4 core.

Supply and fix Energy efficient LED Bright batten light fitting 18 watt, 230 Volts,Box type, lum > 100 lum/W, PF > 0.95, AC 4 feet long including 18 watt LED tube light, etc and accessories, including required fixing arrangements and electrical connection three core copper cable from ceiling rose to light fitting, complete all as specified and as directed by the Engineer-in-Charge. Make: Havells Cat No. LHEBAAPW1W018 or equivalent in approved makes in Particular Specifications of tender documents

Supply and fix decorative Energy saver LED luminary suitable for wall mounting 10 watt retrofit LED, lumen > 100 lum/W, PF > 0.95, including 10 watt LED lamp, complete with LED 10 watt, lamp holder complete made up of polycarbonate including fixing arrangements and taking down old rusted bracket fittings, complete all as specified and as directed by the Engineer-in-Charge. Make: Havells Cat No. LHEOALP7PZ6J010 or equivalent in approved makes in Particular Specifications of tender documents

Supply and fix ceiling fan 1200 mm sweep complete with down rods and blades , minimum air delivery 210CFM with service valve, 6 BEE, and electrical connections, BEE 5 Star rated, complete all as specified and as directed by the Engineer-in-Charge. Make: Cat part No. ES NEO of Havells or equivalant in Khaitan / USHA / BAJAJ

Supply and fix Energy efficient sturdy engineering plastic exhaust fan 300 mm, 1200 RPM, 240 Volts, heavy duty, copper winding including frame and louvres, including cutting of circular hole suitable for 300 mm sweep exhaust fan grouting nuts and bolts and finishing disturb surfaces 5 star rated, complete all as specified and as directed by the Engineer-in-Charge. Make: Turbo Force SP of Havells or equivalent in approved makes in Particular Specifications of tender documents

Supply and fix decorative LED 2'x2' luminary suitable for surface mounting 36 watt retrofit LED, 220 watt, lum > 100 lum/W, PF > 0.95, AC, recessed type with high efficiency PMMA diffuser soft glare free light complete with LED 36 watt, lamp holder complete made up of polycarbonate including fixing arrangements, complete all as specified and as directed by the Engineer-in-Charge. Make: Cat No. LHEDDZP7PW1W036 of Havells or equivalent in approved makes in Particular Specifications of tender documents

Supply and fix LED Street light fitting 70Watts, 230 volts, >100lum/W, beam angle of ǿ 120°, AC outdoor type with high Pressure Die Cast aluminum Housing and heat resistant complete with LED lamp, driver, bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection with all accessories, complete all as specified and as directed. Make: Cat No. LHETAXU7IA7J070 of Havells or Equivalent make as specified here-in-after.

SUB TOTAL OF SCHEDULE "A" Part - II

SCHEDULE "A" PART - III [AIR CONDITIONING]

Supply and Install Hi Wall Split units indoor / outdoor complete with cordless remote control unit and with In-Built Air ioniser and plasma filter with inverter technology for better Indoor Air quality with minimum 3 star rating and EER 3.2 of capacity 1.5 TR, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled Indoor type & designed for input variation between 170 V to 270 V with output Voltage stabilized at 230 V with accuracy of +- 2.5% and of capacity 4KVA suitable for Split type ACs, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled Indoor type & designed for input variation between 170 V to 250 V with output Voltage stabilized at 230 V with accuracy of + 2.5% and of capacity 1.0KVA, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for single pole and neutral enclosure with a two pin and earth plug and Socket complete with one single pole MCB 20Amps, 240V, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of water cooler fully stainless steel, electric driven single phase having approx storage and nominal cooling capacity 40/20 ltrs, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix refrigerator, electric driven (single phase), 195 ltrs, BEE 5 star rated, complete all as specified and as directed by the Engineer-in-Charge.

SUB TOTAL OF SCHEDULE "A" Part - III

SCHEDULE "A" PART - IV [LIGHTNING PROTECTION]

Supply and fix single pointed air termination aluminium rod 12 mm, 300mm long, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for aluminium strip 25 x 3mm with saddles and fixing screws etc. for roof conductors and down conductors above ground with heavy duty plastic insulator, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for test point terminal block made of gun metal or phosphorus bronze size 75 x 75 x 25mm drilled and screwed including 3 nos 8mm dia 25mm long hex head screw, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for 40mm bore `light grade` galvanised tubes, laid in trenches, complete all as specified and as directed by the Engineer-in-Charge.

SUB TOTAL OF SCHEDULE "A" Part - IV

SCHEDULE "A" PART - V [POWER FENCING]

Supply installation, testing and commissioning of IP based Fence Controller (DUAL Zone configuration) Operating voltage between 90V & 265V AC 50-60 Hz and 12V DC for Battery back up if AC failure. The controller should comply to IEC603352-76 and IS 302-2-76, complete all as specified and as directed by the Engineer-in-Charge.

Supply installation, testing and commissioning of power supply unit for DC power supply 12-18V DC-1 Amp, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of Software and licence for Central Monitoring, installed on the SQL backend, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of Alarm device operating on 12V having audibility of 110 db level, alarm must turn ON automatically at all the field controller locations and CMS when fence is damaged of voltage on the fence is 3KV, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of servo controller / UPS 230 VAC, 1 KVA capacity with high voltage cut off (270 VAC) and low voltage cut off (170 VBAC), complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of live fence indicator capable of flashing a thin visible momentary light with each pulse emitted by the controller, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of Sealed 12V 65 AH Low Maintenance battery for use as external stand by backup power source for fence controller with charge regulator, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of lightning divertor capable of diverting stray lightning from fence to earth , complete all as specified and as directed by the Engineer-in-Charge.

Supply of pocket size hand held digital voltmeter for measuring the fence voltage capable of displaying fence voltage upto 10 KV, having auto turn facility when controller pulse is detected, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of suitable outdoor console rack made out of 3mm thick CRCA sheet steel suitabel for extensive outdoor application and comply to required IP standard for Housing fence controller, battery, Automatic voltage regulator, ethernet switch, power supply board etc with suitable power supply distribution MCB's and internal wiring and 5A power supply socket and internal lighting arrangement with suitable lock and key arrangement. The console rack to be fixed on a suitable Angular iron frame of height of 1200mm from the ground level, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of armoured optic fibre cable of six core SM ethement communication between controllers and the CMS, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of Ethernet to OFC convertors at Fence Controller points - 4 port ethernet switch, 10/100 Mbps, complete all as specified and as directed by the Engineer-in-Charge

Supply, Laying, testing and commissioning of Aromoured CAT 6 cable, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of Desktop computer intel core 2 Duo processor, 4GB Ram, 500 GB Hard disc drive, without optical drive 21'TFT Monitor, ethernet, keyboard and mouse with microsoft windows licenced OS, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Laying of XLPE insulated, PVC sheathed, galvanised steel strip of wire armoured, under ground power supply cable of 1100 Volts grade of cross sectional area of 2.5 sqmm 3 core multicore copper conductor, complete all as specified and as directed by the Engineer-in-Charge. Note: Excavation and earthwork, protection of cable, etc., shall be measured and paid separately if cable is laid in trenches.

Supply and Fixing of Intermediate security posts 3M design: 2mm thk CRCA sheet strip roll formed into a special profile for high security and hot dip galvanised to Minimum of 60 microns 3 mtr height with pointed top and having pre punched holes (3mtr high, 32 Line configuration). Suitable to fix on intermediate post assembly the post profile should be in such a way that there is no visible cable connectivity from the outside to give ulmost security complex, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fixing of Intermediate posts assembly 3M design: The post will be of 40mm dia ISI marked MS pipe, medium grade, 3mm thick and hot dip galvanised to Minimum of 60 microns, total height of post assembly shall be 2.5mtr (2.0mtr+0.5 mtr for grouting)complex, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fixing of end post assembly 3.0M design: comprises of 1) Main post:3m high (3m+0.5m for grouting 50mm dia ISI marked MS pipe, medium grade, 3mm thickness with 60 mic hot dip galvanising,2) Support post:3.0m long, 32mm dia ISI marked MS pipe, medium grade, 2mm thickness with 60 micron hot dip galvansing.3) Kiwitah post:3.0m high, 2mm thk CRCA steel strip roll formed into special security profile with no visibel cable connectivity and 60 microns hot dip galvanised with prepunched holes to be fixed on the main post with the help of T straps, complete all as specified and as directed by the Engineer-in-Charge.

Supply and Fixing of Corner post assembly 3.0M design: comprises of 1) Main post:3m high (3m+0.5m for grouting 50mm dia ISI marked MS pipe, medium grade, 3mm thickness with 60 mic hot dip galvanising,2) Support post:2 no.s of 3.0m long, 32mm dia ISI marked MS pipe, medium grade, 2mm thickness with 60 micron hot dip galvansing.3) Kiwitah post:3.0m high, 2mm thk CRCA steel strip roll formed into special security profile with no visibel cable connectivity and 60 microns hot dip galvanised with prepunched holes to be fixed on the main post, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of breakway insulators: The insulators to be used on intermediate security posts made of high- density polythylene UV stabilized having a shield to prevent arcing between wire and post with glossy surface to prevent accumulation of dust and facilitate cleaning, the construction and design of the insulator will be such that it will facilitate triggering of an alarm in the event of an intruder attempting to climb. The insulator must have a break down voltage of at least 15KV. Intermediate insulators must have two wire retaining lugs that field upon a load of 30 to 40 kgs, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of end strain hooks hot dip galvanised upto 30 microns to facilitate fixing starin insulators and tensioners, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of end starin insulators of high impact, high strength UV virgin nylon material capable of withstanding upto 15 KV and shall not allow power leakage, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of corner strain hooks hot dip galvanised upto 30 microns to facilitate fixing starin insulators and tensioners, complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of corner starin insulators of high impact, high strength UV virgin nylon material capable of withstanding upto 15 KV and shall not allow power leakage , complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of joint clamps of spin galvanised MS material, fastener shall facilities firm connection of fence stand size upto 4mm (3/16'' 8 guage), complete all as specified and as directed by the Engineer-in-Charge.

Supply, installation, testing and commissioning of configuration likes made of HT wire galvanised 2.59mm , complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix spacers made of UV stabilized Engineering grade plastic of approx 10mm thickness used to fix the intermediate roll formed security post to the intermediate post assembly with the help of the high quality steel tex screws, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix pitch wire strainer made of stainless steel for corrosion resistance, faiclitating combined application for wire tightner and strain insulator, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix high tensile wire of 2.59mm with zinc coating of min 230 gsm corrosion resistant having UTS of 140kg / Sqmm as per IS 398, complete all as specified and as directed by the Engineer-in-Charge.

Supply, laying, and termination of HV double insulated cable of interconnection between the fence controller and power fence, made of two layer of insulation. Outer insulation shall be abrasion resistant High density Polyethlene and inner insullation made of Polyporopelene, core shall be of 2.5mm galvanised steel, the diameter with inner insulation shall be 4.1 mm and diameter of the cable with both insulation shall be 7.6mm, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix warning sign board of size 250 x 150 x 3mm in bright yellow colour and having legible information in both sign and the languages of Hindi and English, installed in the fence lines at suitable height for visibillity, complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying HDPE pipe of 3/4'' rigid and made of good plastic material used for cable routing, complete all as specified and as directed by the Engineer-in-Charge.

Supply and install super earth kit comprising of non rusting stainless steel rod 304 grade inserted in moisture absorbant chemical mixture, earth kit must weight min 4 kg, 4ft long, fastening assembly shall be of hot dip galvanised and made of stainless steel, complete all as specified and as directed by the Engineer-in-Charge.

Supply and install Network rack at control room, complete all as specified and as directed by the Engineer-in-Charge.

Supply and install Sliding Gate top electirification with Gate Switch, complete all as specified and as directed by the Engineer-in-Charge.

SUB TOTAL OF SCHEDULE "A" Part - V

SCHEDULE "A" PART - VI [CCTV CAMERA SYSTEM]

Supply and fix Net work cameras AxisQ 6215-LEH 264 or equivalent, Image, sensor CMOS, Image sensor size -1/1.9, wide dynamic range , Min illumination / light sensitivity (color) - 0,07 lux, motion - JPEG, built -in - IR, Operating temperature- (50 to 55 oC), Vandal rating - IK10, IP rating - IP66, IP68, Designed for repaint, Max video resolution - 1920*1080,Max frames per second - 50/60, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Cameras AxisP 1435-LEH 264 or equivalent, Image sensor - CMOS, Image sensor size - 1/1.9, Focal Length mm - 3~ 10.5, Min illuminaton/ light sensitivity (color) - 0.07 lux, Motion -JPEG, Built-in-IR, Operating temperature - (-30~+55oC (-22~ +131 F)), Electronic Shutter Range - 1/66500~2s, IP rating -IP66, Lightfinder and WDR , Max video resolution -1920*1080, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix VMS Milestone License , Specifications: Maximum number IP devices (1) per recording server - 8, 2021 R2, Maximum number of users - Unrestricted , Supports Xprotect Smart Client , Xprotect Web Client and Xprotect Mobile - Yes, Secure HTTPS camera connectivity (on supported devices )- Yes, H. 264, MJPEG-4, MPEG-4, MPEG-4 ASP & M*PEG , Centralized management , Recording server communication encryption , Management Server communication encryption, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix 55 inch Wall Display Specifications : Dimensions 124.1 * 3.6 * 1.8 cm; 600 Grams, Resolution - 4K Ultra HD (3840 * 2160), Connectivity: 4 HDMI ports, 2 USB portsall, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Joy Stick Axis T8310 video Surelliance Control Board. Specification: Hall- effect joystick with three axis X/Y : for pan and tilt Z: Knob for zoom 6 application defined hotkeys, Deflection - Square delimiter Pan/Tilt (XY): +/- 15 o Zoom (Z) : +/- 25o, Dimensions - 4.3 *7.2 * 7.1" (109 * 182 * 181 mm), Interface - 2x USB type A, 1x USB type B, Functions - 22 Keys: 10 application defined hokeys of which 5 are backlit, 0-9, tab, alt, Shuttle operating angle 160, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Hard Disk - 4 TB External for Surveilance Backup , Specifications: Cameras Supported - Upto 64, Max. Sustained Transfer Rate OD (MB/s) - 190MB /s , cache (MB) - 64 , Average Operating power (W) - 5.5 W Standby Mode / Sleep Mode , Typical (W) - 0.25/0.25, Operating (drive case , max oC) - 70 , Drive Bays Supported - +8, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix 8 Port POE Network Swithces. Specifications : 8- Port 10/100/1000M poE with 2 Combo SFP ports , Wireless Communication Standard - 802. 11n, Voltage 240 Volts, Wattage 14.45 Wattts, Dimensions 28*12.6 * 4.4 cm, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix GI pipe, medium grade, 80 mm bore complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix PC - Tower Business Desktop - w/ 10th gen Intel Core - 8GB , Windows 10 Pro , 3.5 inch 1TB 7200rpm SATA Hard Disk Drive, 260W up to 85% efficient power Supply , 8GB , 1*8GB , DDR4 non ECC memory, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix 32 CHANNEL NVR - H 264 - 1960 P, Resolution : 8MP / 5MP/4MP/3MP/1080P/720P/D1//CIF/QCIF,2 SATA with RAID 4k, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix 1.5 Sqmm 3 Core Power Cable FRLS , Flexible Cable , Voltage Grade : 1100 V , Copper Conductor , IS 694: 1990, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix 6 kVA Online UPS With 4 Hrs Battery Backup , Battery Type SMF - VRLA , DC Voltage 192V, Rating in VA , Watts 6 KVA , 5.4 KWall, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing including testing and commissioning of fixing / laying of 6 core armoured single mode optical fibre cable running through with 1" dia HDPE conduit pipe with all accessories, complete all as specified and as directed by the Engineer-in-Charge. Note: One running metre of Cat 6 OFC and one running metre of HDPE conduit shall be measured as one unit.

Supply and fix 6 Core OFC Cable , Voltage 220V Single Mode , Overall diameter 6.2mm, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix 20 mm HDPE Pipe, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix 20 mm PVC Casing / Caping, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing Laying Charges for OFC in HDPE pipe , cat 6 cable PVC, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix ATN Matrix Unit which includes the ATEN Matrix Display Switcher Scaler along with connects upto 10 displays , HDMI Input/Output and user friendly multiple view Configuration complete all as specified and as directed by the Engineer-in-Charge.

All as per item No. 6.18 here-in-above but including the Work station having Core 6 processor of 16 GB Ram, 500GB HDD 4GB 2*2 or 4 Graphic card with wireless KB+M and 21" Display(03Nos) Model No. Precision Tower 3630 of Make Dell or equivalent in HP/ Lenovo complete.

All as per item No. 6.18 here-in-above but including the HDMI Cable (5 mtr) complete.

SUB TOTAL OF SCHEDULE "A" Part - VI

SCHEDULE "A" PART - VII [EXTERNAL WATER SUPPLY]

Material and Labour for cutting the existing 150mm CI/DI pipe and inserting reducer/tee etc of suitable size as required at site including earth work, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for 50mm bore `Medium grade` galvanised tubes with all fitting, laid in trenches, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for 40mm bore `Medium grade` galvanised tubes with all fitting, laid in trenches, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for 25mm bore `Medium grade` galvanised tubes with all fitting, laid in trenches, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix gun metal gate valve, painted finish, with forged brass spindle and iron wheel head, screwed both ends internally IS-778 marked, Class-2, for iron pipe of size 25mm bore, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix gun metal gate valve, painted finish, with forged brass spindle and iron wheel head, screwed both ends internally IS-778 marked, Class-2, for iron pipe of size 50mm bore, complete all as specified and as directed by the Engineer-in-Charge.

Material and Labour for Valve chamber of size 1500mm x 1500mm x 1000mm internal dimensions, with and including excavation in any type of soil, spreading, levelling and refilling etc. PCC (1:4:8) type D2 for foundation, Fly ash brick work of one brick thick wall in CM (1:4) including internal plaster 15mm thick in CM (1:4) external plaster 15mm thick(1:4) upto 150mm below GL and providing coping in PCC (1;2:4) type B1, angular iron frame of size 50x50x6mm with 6mm thick MS plate cover complete including locking arrangements and having FRP coating of 2mm thick on both inside and outside surfaces, complete all as specified and shown in TD drawing.

SUB TOTAL OF SCHEDULE "A" Part - VII

SCHEDULE "A" PART - VIII [External Electric Supply]

Material and labour for Galvanized Steel High mast light 16m height, mast shaft with hot dip galvanized, suitable for wind velocity of 198Km/hour and soil bearing capacity of 20 TON/Sqm as per IS-875, 3mm section thickness with top 150mm dia and bottom 340mm dia, suitable for 8 lantern symmetrically fitted along with their control gear and having two point suspension system with stainless steel wire rope of 6mm dia, 97/19 gauge and double drum winch with luminaire mounting arm, pulley assembly, galvanised carriage arrangement for 8 lights, 3 phase integral power tool with motor for lifting and lowering, lightning arrester spike, with foundation bolts manufactured from special steel along with nuts, washers, anchor plates, control panel with control cable, outdoor standard feeder pillar with 32A TPN MCB incomer, single dial time switch, 25A TP Contactor for automatic operation of luminaries, power tool control with 2 Nos Contacts and raise lower push button, switch gears and templates, with all accessories, including excavation, earth work, RCC M30 foundation as per OEM recommendations, complete all as specified and as directed. Note: Light fittings will be measured and paid for separately. Make: Cat No. BHMRL 16E of Bajaj or Equivalent model of Philips / Crompton Greaves / Havells

Supply and fix LED street light fitting 120 Watt 230 V AC outdoor type with high pressure diecast aluminum hosing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete withIP 65/66 protection, complete all as specified and as directed by the Engineer-in-Charge. Model No. ENDURAPEARLPLUSSL120WLED757PASYTOPC of Make Havells or equivalent approved make given in Particular Specification in tender documents.

Supply and laying GI tubing light grade of size 40mm bore for cable protection, complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying tubing light grade of size 80mm bore for cable protection, complete all as specified and as directed by the Engineer-in-Charge.

Supply, laying and testing of cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor in ground/gallery/surface, of 1100 volts grade, of 120 Sqmm 3.5 core complete all as specified and as directed by the Engineer-in-Charge. Note : 1. Quoted rate includes cost of cable glands, ferrules and other connecting accessories if any. 2. Excavation and earthwork and protection of cable, etc., if required, shall be measured and paid separately under relevant items of BoQ.

All as per item No.8.05 here-in-above but 95 Sqmm 3.5 core complete.

All as per item No. 8.05 here-in-above but 25 Sqmm 4 core complete.

All as per item No. 8.05 here-in-above but 16 Sqmm 4 core complete.

Supplying and laying un-reinforced precast concrete cable cover, class LV, Type 1, flat size 250mm x 150mm x 40mm, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix Synthetic Insulating Mat of size 2m x lm x 19 mm suitable for 1100 Voltage as per IS , complete all as specified and as directed by the Engineer-in-Charge.

Supply,install, testing and commisioning at inside the watch tower of long range security search light with tripod stand of 1mtr long with castrol wheel high intensity weather proof flood light in aluminium body complete with highly polished parabolic stainless steel mirror back and inside reflector toughned front glass with operating arrangement of both vertical and horizontal control working at single phase 230V 400 watt MH(5Modes) operating range upto 1KM inclusive provision of all connected accessories like electric lead, MH lamp fixing arrangements etc., complete all as specified and as directed by the Engineer-in-Charge. Make : Philips / Havells / Sigma / Bajaj

Supply, installing, testing and commissioning of LT feeder pillar box, factory made, cubical, outdoor, double door (CPRI approved), fabricated out of 3.15mm thick MS sheet, board floor mounted, dust and vermin proof, suitable for voltage 415V, 3 phase, 4 wire, weather proof, with separate hinge door for each compartment with locking arrangement with back door common openable (screwed), grouted in PCC 1:2:4 complete including painting with two coats of synthetic enamel paint over a coat of red oxide primer and including 200A, solid copper busbar (TPN) suitable double compression aluminium cable glands, with and including the following accessories, complete all as specified and as directed by the Engineer-in-Charge. :- Location- High Mast Light Incoming- (a) MCCB 40 Amp 4Pole 10kA 415 Volts- 01 No Outgoing- (a) MCCB TPN 25 Amp 4Pole 10kA 415 Volts- 01 No (c) Aluminium busbar 100 Amps (set of three) - 01 set (d) Digital voltmeter -01 No (e) Digital Ammeter suitable CT's - 01 No (f) Timer switch - 01 No (d) LED indication lamp (R-Y-B) - set of three (e) Space for MCCB 25 Amp 4 pole - 01 No

Supply, installing, testing and commissioning of LT feeder pillar box, factory made, cubical, outdoor, double door (CPRI approved),fabricated out of 3.15mm thick MS sheet, board floor mounted, dust and vermin proof, IP 55 protection, suitable for voltage 415V, 3 phase, 4 wire, weather proof, with separate hinge door for each compartment with locking arrangement with back door common openable (screwed), grouted in PCC 1:2:4 complete incl painting with two coats of synthetic enamel paint over a coat of red oxide primer and including 200A, solid copper busbar (TPN) suitable double compression aluminium cable glands, with and including the following accessories, complete all as specified and as directed by the Engineer-in-Charge. :- Location- Power Fencing Incoming- (a) MCCB 40 Amp 4Pole 25kA 415 Volts- 01 No Outgoing- (a) MCCB TPN 32 Amp 4Pole 10kA 415 Volts- 01 No (c) Aluminium busbar 100 Amps (set of three) - 01 set (d) Digital voltmeter -01 No (e) Digital Ammeter suitable CT's - 01 No (d) LED indication lamp (R-Y-B) - set of three (g) Space for MCCB 32 Amp 4 pole - 01 No

Supply, installing, testing and commissioning of LT Panel board factory made, cubical, outdoor type (double door) as per IEC 61439 Part 1&2 (Switchgear OEM design), with following minimum thickness- load bearing member/doors- 3mm, non load bearing member/internal partitions- 1.5mm, gland plate/ base channel- 3mm, board floor mounted, dust and varmin proof IP-66 rating, 3 phase 4 wire with rated operational voltage 433V rated insulation voltage of 1000V and impulse with stand of 12kV and minimum internal arc withstand of 65kA, 500msec as IEC61641, weather proof with separate hinge door for each compartment wiith operating handle and locking arrangement with back door common openable (scrwed/lockable), grouted including suitable angle frame with PCC 1:2:4 complete painting as per OEM define 7 tank process with epoxy powder polymeriz at high temperature and 400A solid copper busbar (TPN) suitable double compression aluminium cable glands with the following accessories:- Location- Main Panel Board Incoming- (a) MCCB 200 Amp 4Pole 25kA 415 Volts- 01 No Outgoing- (a) MCCB 160 Amp 4Pole 25kA 415 Volts- 01 No (Bldg V TPN) (b) MCCB 40 Amp 4Pole 25kA 415 Volts- 03 Nos (c) MCB 40 Amp 4Pole 10kA 415 Volts- 02 Nos (d) Digital Ammeter including suitable CTs- 01 set (e) Digital Voltmeter- 01 No (f) LED indicator lamp (R-Y-B) 01 No set of three (g) Space for MCCB 40 Amp 4 pole - 02 Nos

SUB TOTAL OF SCHEDULE "A" Part - VIII

S A R CONSTRUCTIONS

Ruchira Associates

S R CONSTRUCTIONS

M/s.DSRK CONSTRUCTIONS

SETH GHANSHYAM DAS LAKHMAMI AND CO

SHELL REFRACTORIES and INSULATIONS