SPL REP TO BLDG NO T/A-22, T-212, T/A, DRAIN AT BLDG NO P-39 TO P-42, PROVN OF 04X INDSTRL STANDING FAN FOR WKSP REP BAY, SPL REP TO BLDG NO P-01 AND PROVN OF 12 NOS CEILING FANS FOR BLDG NO T-110, T-117 AND T-118 AT DHARCHULA UNDER GE PITHORAGARH

Amount

DESCRIPTION OF ITEMS

Excavation in trenches n.exc. 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells cesspits, manholes, pier holes etc n exc 10 Sqm on plan getting out in hard/dense soil.

Demolition of cement concrete in ground floor,paving nexc 15mm thick(below or above GL) complete all as specified and directed

Demolition of precast cement concrete block /brick wall masonry built in cement mortar complete all specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n.exc 25 cm

Removing excavated soil exc. 250 m but n.exc 500m and depositing where directed.

M & L for Plain Cement concrete 1:4:8, type D2 using 40mm graded stone aggregate in foundation, filling and mass concrete complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B1 using 20 mm graded stone aggregates in surface channels and drains complete all as specified and directed.

M & L for Plain Cement concrete 1:2:4 type B1 using 20 mm aggregate in coping and the like including weathering, slightly rounded for chamfered angles and throating complete all as specified and directed.

M&L 15 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surface including finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick plain cement concrete, 1:3:6 type C-2, using 40 mm graded stone aggregate as in plinth protection complete all as specified and directed.

M&L for 25 mm th PCC 1:2:4 type B1 using 20 mm graded stone aggregate as leveling course, complete all as specified & directed.

Demolition of brick work, stone/boulder masonary built in cement mortar complete all speecified and directed.

M&L for precast cement concrete block masonary with PCC 1:3:6 type C-1, block exc 10cm in width and set in CM1:6 complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm and not exceeding 0.36 sqm, in floors over and including 15mm thick screed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified & directed.

M&L for coloured glazed ceramic tiles in verticla surface, 450x350x7mm thick set and jointed in neat sement slurry and pointed in white or colour cement to match over 10 mm thick plaster in CM 1:4 complete all as specified & directed.

M&L for Chequered cement concrete tiles 30cm x 30 cm x 25 mm thick set, jointed and pointed in neat cement slurry with grey cement and pigments in floor including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed

M&L Granite (of any type) tiles 18-20 mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 15mm thick screed in CM 1:6 etc complete all as specified and as directed

Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided, complete all as specified & directed.

M&L for RCC 1:2:4, type B1 using 20mm graded stone aggregate as in slab of shelve complete all as specified and directed.

Use & waste of Formwork to soffits of slabs, rough finished concrete surfaces complete all as specified and directed.

M&l TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Taking down chowkhats or frame n exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 sqm but nexc 4.00 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

M&L for 35 mm thick plain, framed pannelled shutters (any number of of panels), with panels with panels of timber flat on both sides (feather edged), or of venered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkhat complete all as specified and directed.

M&L for 35 mm thick glazed skelton shutters of 2nd class hard wood with or without sash bars edges of framing plain chamfered or rounded with cut and metered beads to secure glass of section as per ssr-I complete all as specified and directed.

M&L 2nd class hardwood plain solid straight chowkhats and frame wrought framed rebated on solid rounded or chamfered complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle and locking arrangement, and steel peg stay, complete with glazing bars, dovetailed or welded including wiremesh shutter all as spfd and as directed.

-ditto- but without glazing bar

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc .50 sqm in each panels complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F 100 mm mild steel but hinges medium weight,cold rolled complete all as specified and directed

ditto but75 mm in size complete all as specified and directed.

S&F 150 mm aluminium handles, cast type anodised complete all as specified and directed.

S&F 125 mm Mild steel barrel tower bolts, stove enammeled black with bright bolts complete all as specified and directed

S& F 250 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and fixed complete

Taking down cement plaster on brick or stone walls, of any description including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L 12 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces including finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surface of wall apply two coat of cement base paint over a coat of white wash complete all as specified and directed.

S&F in repairs vitrous china wash basin,white flat back size 550X400mm including pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks, 32mm in size Waste fittings, brass, chromium plated and brackets fixing in position complete all as specified and directed.

S&F in repair sink made of stainless steel 1 mm th kitchen or laboratory with plugs, washers & waste coupling, incl bedding in CM to dwarf wall or incl fixing cantilever brackets & connecting union to pipe over all size 495x420mm bowl size 410x330 mmx160 mm complete all as specified & directed.

S&F 15 mm Stop valves, cast copper alloy, screwed down, high pre-ssure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repairs complete all as specified & directed.

M&L for 32/40 mm in size Waste fittings, brass, chromium plated for stainless steel sinks, glazed ware basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed in reapirs

S&F PVC connections 15 mm size with PTMT nuts of length 600mm long fixed in repairs all as specified and as directed.

S&F PVC waste pipe 32/40 mm dia for wash basin/kitchen sink in repairs complete all as specified and as directed.

S&F 15 mm bore GI tubing with all fittings medium grade fixed to wall or laid in floor etc including taking up or down 15 mm GI tubing complete all as specified & directed

S&F in repairs bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass furrel and fixed 15mm dia complete all as specified and directed.

Supply and fix 500 Ltr rotational moulded polyethylene water stotage tanks ( cylinderical vetrticle with closed top) hoisted & fixed in position including Dismantling water tank capacity exc 250 ltrs but nexc 500 ltrs and removing to stores complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc all as specified and as directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and gastenings and heavy brackets framing (beam, tee, angle channel or flat sections) (Fe-290 Gde E-165) inicluding distance pieces, cleats etc.

M&L for mild steel framed wk as in doors or gates of angle iron or other section complete drilled for fixing of steel sheeting or other covering doors, etc to be prepared for hanging or sliding with & incl either hooks & hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rail sand suides) & hanging, also fastening & fixing Fe-290, Gde-165 complete all as specified & directed.

S&F 1 mm thick plain mild steel sheet to door shutters covering to door chowkats fixed to steel memebers with plain 40 mm lap joints or welded or riveted etc all as specified.

Dismantling of wall and celing boards/AC sheets in any thickness & any position including cover fillets complete all as specified and directed.

M&L for 6mm thick Plywood, grade BWR, type BB, fixed in ceiling and walling with screws to timber frame work complete all as specified and directed.

Dismantling of timber scantling 40 sqcm and over in section in any position for unframed works complete all as specified and directed.

M&L for 2nd class hard wood as in scantling clean sawn framed & fixed as in ceiling and walling wks, complete all specified & directed.

Dismantling of timber scantling 40 Sqcm under in section in any position, fixed with nails unframed work complete all as specified & directed.

M&L for II nd class hard wood plain fillets square or rectangular in section clean sawn secured with nails sectional area exc 13 sqcm and n.exc 25 sqcm complete all as specified and directed.

M&L II nd class hard wood plain fillets square or rectangular in section cleansawn but bullnosed chamfared or rounded on one edge or face sectional area exc 3 sqcm and nexc 6 sqcm secured in nails complete all as specified and directed.

M&L for one coat of creasote oil to wooden surfaces new or old of any description including prepration of surfaces complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting of any guage/thickness in roof covering/wall clading complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F 0.63 mm Galvanised, corrugated mild steel sheeting with two corrugations side lap fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275. complete all as specified and as directed .

M&L for two coat of synthtic enamel paint over a coat of pink primer to new wooden surface of any description exc 10 cm girth or width including prepration of new wooden surfaces complete all as specified and directed.

M&L for one coat of synthtic enamel paint on old wooden surface of any description exc 10 cm girth or width including prepration of surfaces complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer to new steel surfaces of any description over 10 cm in width or girth incl preparation of new steel surfaces complete all as specified and directed.

M & L preparing old previously treated surfaces of corrugated/plain sheets as in roof covering /wall over 10 cm girth or width by cleaning straightening if any removing rust and making good where required and applying one coat of synthetic enamel paint on old steel surfaces complete all as specified and directed.

M&L 100mm thick cement concrete 1:4:8 type B2, using 40mm graded stone aggregate as in path/hardstanding complete all as specified and directed.

S&F of 100 mm size aluminium handles cast type anodised complete all as specified and directed.

S&F 200mm mild steel sliding door bolts,plate type ,stove enamelled black ,with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate all as specified and directed.

S&F 200mm long mild steel barrel tower bolts stove enamelled black with bright bolt and fixed to frame all as specified and directed.

S&F in repair steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and directed.

S&F 12mm thick perforated tiles for insulation purpose 60x60cm in size ,fixed with staples or snap grid complete all as specified and directed.

S&F anodised aluminium snap grid of size 606 x605mm frame work for false ceiling complete all as specified and directed.

S&F hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 type C-2, (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for rendering 15mm thick cement plaster on external surface of wall in two layers, 10mm thick in CM 1:6 and 5mm thick in CM 1:4 with water proofing compound complete all as specified and directed. Note: Water proofing compound to be measured and paid separately.

Supply only Integral waterproofing compound.

M&L for preparation of old steel surfaces of any description and applying one coat of synthetic enameled paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying three coat of white wash complete all as specified and directed.

E&M Portion: Taking down carefully copper/aluminium point wiring (light, fan, socket or power ) complete and making good disturbed surfaces of walls, floors etc all as specified and directed.

M&L point wiring with 1.5 Sqmm (Nominal cross sectional area) single core PVC insulated with PVC unsheathed multi stranded copper conductor FRLS cable in open/ surface PVC conduit of suitable size, complete with all accessories/fitting and heavy duty PVC terminal switch board for mounting switches, sockets, regulators of suitable size with plastic module surface sheet top cover open recessed on all and brass screw and washer including unsheathed single core PVC insulated cable green in colour 1.5 Sqmm multistranded copper conductor as contineous earth wire and connecting to earth dolly complete all as specified and directed: (a) One light point/Fan point controlled by one way switch of 5/6 Amps

(b) One 3/5 pin socket outlet point on same board controlled by one way switch of 5 Amps but with cables 1.5 sqmm size

(c) One 3/5 pin socket outlet point on independent board controlled by one way switch of 5 Amps but with cables 1.5 Sqmm size

(d) One 3/5 pin socket outlet point on below board controlled by one way switch of 5 Amps but with cables 1.5 Sqmm size

M&L power point wiring with 2.5 Sqmm (Nominal cross sectional area) single core PVC insulated with PVC unsheathed multi stranded copper conductor cable in open/surface PVC conduit of suitable size, complete with all accessories /fitting and heavy duty PVC terminal switch board for mounting switches, sockets of suitable size with plastic module sheet top cover open recessed on all and brass screw and washer including unsheathed single core PVC insulated cable green in colour 2.5 Sqmm multistranded copper conductor cable as earth wire and connecting to earth dolly complete all as specified and directed for 3/5 pin, 15/16 Amps power socket controlled by one no, one way switch of 15/16 Amps complete all as specified.

S&F in repair switch piano flush button single pole one way 5 Amps complete all as specified and directed.

S&F in repair switch piano flush button single pole one way 15 Amps complete all as specified and directed.

S&F in repair socket out let 3 pin 5/6 Amps flush type complete all as specified and directed.

S&F in repair socket out let two in one 3 pin 5/6 Amps and 3 pin 15/16 Amps, flush type, non shutters, non interlocking complete all as specified and directed.

S&F in repair ceiling rose, surface bakelite, AC, 60x30mm, 3 terminals complete all as specified and directed.

S&F in repair lamp holder PVC /poly carbonated type with back plate suitable for pendants /angular /batten fittings complete all as specified and directed

S&F in repair stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and directed

S&F sheet metal enclosure for DB SPN 4 way with 200 Amps rated busbar 240 Volts, double door suitable for housing MCBs and isolators complete all as specified and directed.

S&F sheet metal enclosure for DB SPN 8 way with 200 Amps rated busbar 240 Volts, double door suitable for housing MCBs and isolators complete all as specified and directed.

S&F in repair MCB SP 6 to 40 Amps, 240 volts 10KA complete all as specified and directed.

S&F in repair MCB SPN 40 Amps, 240 volts 10KA complete all as specified and directed.

Taking down carefully sheet metal enclosure DB SPN 4/8 way with 200 Amps rated busbar 240 Volts, single/double door complete including MCBs and isolators complete all as specified.

S&F in replacement LED tube light 4' long along with all fixtures and fittings, internally pre wired and including connecting up to ceiling rose with twin core twisted flexible copper conductor cable with suitable size, 20W complete all as specified and directed.

S&F in repair LED Bulb/LED retrofit 'T' bulb 12 watts, complete all as reqd at site and directed.

S&F in repair 1x35 watt LED building security light fitting, with and including GI bracket made out of 1.5 mtr GI pipe bent to shape light grade of 40mm dia, bracket clamps nut bolts and washers etc and making electric connection with 3 core 1.5 sqmm PVC insulated copper conductore cable complete all as specified and directed.

Taking down ceiling fan, sealing cable end, dismantling blades and refixing the same complete with three blade, down rod, accessories and connecting up with twin core twisted flexible cable from ceiling rose complete all as specified.

M&L for taking out burnt copper winding from ceiling fan of 1200 mm size and rewinding with existing /same guage of super enammeled copper winding wire including replacing ball bearing complete all as specified and directed.

Taking down exhaust fan, sealing cable end, dismantling blades and hanging the same complete with blades, accessories and connecting up with twin core twisted flexible cable from ceiling rose complete all as specified.

M&L for taking out burnt copper winding from exhaust fan 300/450 mm size and rewinding with existing /same guage of super enammeled copper winding wire complete all as specified and directed.

Taking down old ceiling fans and S&F Ceiling fans complete with three blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE and making necessary connection to ceiling rose complete all as specified.

M&L for dismantling old earthing and providing new earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick, buried directly in ground (earth pit not less then 2.25 metres deep below ground level) with top edge of the plate not less then 1.5 metres below normal ground level, conneted to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, cheek nuts and washers of galvanised or iron protected by 15 mm bore GI pipe (medium grade) and connected to main switch board as directed including concrete pit in PCC (1:3:6) type C1 precast RCC (1:2:4) type B1 cover slab 40x40 Cm x 6Cm reinforced with 8 mm dia deformed bar @ 5 cm c/c with one handle for lifitting made out of 8 mm dia MS bar, funnle, wire mesh, 20 mm bore GI pipe (medium grade) for watering including charcoal and salt in alternative layers necessary excavation and earth work in any type of soil and testing complete all as shown on electrical plate No-3 of SSR part-I, 2009.

S&f in repair 1100 volts grade heavy duty 2 core x 10 sqmm cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular

S&f in repair for house service bracket (hook type) complete with 3.0m long G.I. pipe 40mm dia Med. grade, two nos 90 degree bends. M.S. hook and stay or guy complete all as specified.

S&f in repair LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S&F in repair bracket made out of GI tubing 1.5 mtr long of 40 mm dia light grade bent to shape with suitable size MS clamps, nut, bolts and washers including one coat of anti corossive primer and two coats aluminium paints with 3 core 1.5 Sqmm multistranded copper cable from LED light to pole box complete all as specified.

S&F Ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE and making necessary connection to ceiling rose complete all as specified.

S&F fan hook, made of Fe-290 Gde E-165 iron round bar 10mm in size for hanging ceiling fan as per site requirement complete all as specified.

S&F of switch piano flush type 5 amps single pole one way complete all as specified and directed by Engr-in-Charge.

S&F of ceiling rose surface type 65 mm x 50 mm, 2 to 3 terminal complete all as specified and as directed by Engr-in-Charge.

Supply and install 450mm, 220 Volts, AC, 50 Hz heavy duty oscillator type propellor fan (industrial standing fan) with impeller consisting of three blades in pedestal type with air delivery not less than 7500 cum/hr, comprising adjustable height feature and robust base to ensure absolute stability including wire of suitable size for connection with plug top and conforming to IS: 2997-1964 complete all as specified.

SK Traders Sons