Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L-1₹120.0 CrAccepted-AOC | ₹120.0 Cr Quoted ₹123.4 Cr | L-1 | Accepted-AOC L-1 Bidder. |
| 2 | L-2₹128.7 CrRejected-Finance 3A RAM MOHAN MULICK GARDEN LANE UNIT NO 6A 3RD FLOOR KOLKATA 700010 | KOLKATA | WEST BENGAL | 700010 | ₹128.7 Cr | L-2 | Rejected-Finance Rejected. Other Than L-1. |
| 3 | L-3₹137.7 CrRejected-Finance CITY TOWER BUILDING ROOM NO 306 CIRCULAR ROAD DIMAPUR 797112 NAGALAND | DIMAPUR | NAGALAND | 797112 | ₹137.7 Cr | L-3 | Rejected-Finance Rejected. Other Than L-1. |
| 4 | Rejected-Technical SITANI BUILDING DINBAZAR JALPAIGURI 735101 | JALPAIGURI | JALPAIGURI | WEST BENGAL | 735101 | - | - | Rejected-Technical Rejected by TSC. |
| 5 | Rejected-Technical NPCC LTD NORTH EAST ZONE HOUSE NO 10 HOUSING COLONY RANGAMANCHA PATH RUKMININAGAR GUWAHATI 781006 | GUWAHATI | KAMRUP METRO | ASSAM | 781006 | - | - | Rejected-Technical Rejected by TSC. |
Tender Value
₹120 Cr
EMD Value
₹15 L
Closing Date
30 Sept 2023, 6:00 pmClosed
HQ CE SILIGURI ZONE, MES, SEVOKE ROAD, PO SALUGARA
HQ CE SILIGURI ZONE, MES, SEVOKE ROAD, PO SALUGARA, DIST JALPAIGURI, PIN 734 008 (WB)
PROVN OF TECHNICAL BUILDING AND ALLIED WORKS (PH-I OF TWO PHASES) AT KATHAR UNDER GE (P) SILIGURI
2023_MES_613589_1
98759/BENG/SZ/E8
Open Tender
Civil Works
1095 days
KATIHAR
Please refer Tender documents.
7 documents required · 7 mandatory
₹3,000
GE (P) SILIGURI
₹15 L
Yes
HQ CE SILIGURI ZONE
24 Feb 2024
12 Aug 2023
7 Oct 2023
12 Aug 2023
30 Sept 2023
16 Sept 2023
12 Aug 2023 - 25 Aug 2023
28 Aug 2023
Amount
BUILDINGS & STRUCTURE (Sch 'A' PART-I)
Lump sum price worked out by the Contractor for “BUILDINGS & STRUCTURE” as listed in Schedule ‘A’ Part-I. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 94,10,65,000.00 inserted by the MES in Schedule ‘A’ Part-I.
EARTHWORK, SITE CLEARANCE AND SITE DEVELOPMENT (Sch 'A' PART-II)
Lump sum price worked out by the Contractor for “EARTHWORK, SITE CLEARANCE AND SITE DEVELOPMENT” as listed in Schedule ‘A’ Part-II. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 4,85,29,260.18 inserted by the MES in Schedule ‘A’ Part-II.
INTERNAL WATER SUPPLY (Sch 'A' PART-III)
Lump sum price worked out by the Contractor for “INTERNAL WATER SUPPLY” as listed in Schedule ‘A’ Part-III. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 2,88,488.08 inserted by the MES in Schedule ‘A’ Part-III.
INTERNAL ELECTRIFICATION (Sch 'A' PART-IV)
Lump sum price worked out by the Contractor for “INTERNAL ELECTRIFICATION” as listed in Schedule ‘A’ Part-IV. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 62,41,165.09 inserted by the MES in Schedule ‘A’ Part-IV.
ROAD, PATH, CULVERT AND HARDSTANDING (Sch 'A' PART-V)
Lump sum price worked out by the Contractor for “ROAD, PATH, CULVERT AND HARDSTANDING” as listed in Schedule ‘A’ Part-V. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 8,62,48,964.08 inserted by the MES in Schedule ‘A’ Part-V.
SEWAGE DISPOSAL (Sch 'A' PART-V(A))
Lump sum price worked out by the Contractor for “SEWAGE DISPOSAL” as listed in Schedule ‘A’ Part-V(A). Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 8,19,322.03 inserted by the MES in Schedule ‘A’ Part-V(A).
AREA DRAINAGE (Sch 'A' PART-VI)
Lump sum price worked out by the Contractor for “AREA DRAINAGE” as listed in Schedule ‘A’ Part-VI. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 1,88,67,583.79 inserted by the MES in Schedule ‘A’ Part-VI.
CHAIN LINK FENCING & STEEL GATE (Sch 'A' Part-VII)
Lump sum price worked out by the Contractor for “CHAIN LINK FENCING & STEEL GATE” as listed in Schedule ‘A’ Part-VII. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 22,40,330.70 inserted by the MES in Schedule ‘A’ Part-VII.
EXTERNAL WATER SUPPLY (Sch 'A' PART-VIII)
Lump sum price worked out by the Contractor for “EXTERNAL WATER SUPPLY” as listed in Schedule ‘A’ Part-VIII. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 46,68,023.90 inserted by the MES in Schedule ‘A’ Part-VIII.
EXTERNAL ELECTRIFICATION (Sch 'A' PART-IX)
Lump sum price worked out by the Contractor for “EXTERNAL ELECTRIFICATION” as listed in Schedule ‘A’ Part-IX. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 2,84,14,865.60 inserted by the MES in Schedule ‘A’ Part-IX.
SUMMER APPLIANCES & LV SERVICES (Sch 'A' PART-X)
Lump sum price worked out by the Contractor for “SUMMER APPLIANCES & LV SERVICES” as listed in Schedule ‘A’ Part-X. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 4,31,800.50 inserted by the MES in Schedule ‘A’ Part-X.
SECURITY LIGHT AND STREET LIGHT (Sch 'A' PART-XI)
Lump sum price worked out by the Contractor for “SECURITY LIGHT AND STREET LIGHT” as listed in Schedule ‘A’ Part-XI. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 1,04,43,671.10 inserted by the MES in Schedule ‘A’ Part-XI.
FIRE FIGHTING (Sch 'A' PART-XII)
Lump sum price worked out by the Contractor for “FIRE FIGHTING” as listed in Schedule ‘A’ Part-XII. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 50,18,797.90 inserted by the MES in Schedule ‘A’ Part-XII.
FIRE ALARM (Sch 'A' PART-XIII)
Lump sum price worked out by the Contractor for “FIRE ALARM” as listed in Schedule ‘A’ Part-XIII. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 36,81,109.37 inserted by the MES in Schedule ‘A’ Part-XIII.
LIGHTNING PROTECTION (Sch 'A' PART-XIV)
Lump sum price worked out by the Contractor for “LIGHTNING PROTECTION” as listed in Schedule ‘A’ Part-XIV. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 13,25,546.30 inserted by the MES in Schedule ‘A’ Part-XIV.
SOLAR HOT WATER (Sch 'A' Part-XV)
Lump sum price worked out by the Contractor for “SOLAR HOT WATER” as listed in Schedule ‘A’ Part-XV. Representing ** ___ % ______ percent *Above / Below the lump sum price of Rs. 5,00,105.68 inserted by the MES in Schedule ‘A’ Part-XV.
MISCELLANEOUS ITEMS REQUIRED FOR B/R & E/M SERVICES (Sch 'A' Part-XVI)
EARTHWORK, SITE CLEARANCE AND SITE DEVELOPMENT Supply of approved earth at Proposed site (Army area) at Katihar from out of MoD land including necessary excavation, loading, transportation, unloading, royalty and all taxes etc. complete all as specified and directed. NOTE :- (a) Earth required for the item shall be supplied by contractor from outside of MOD land of any lead, at his own arrangement. (b) All cost of procurement of earth including cost of transportation, compaction royalties, tax etc shall be deemend to be included in the unit rate quoted by the contractor. (c) Forming embankments / filling in low lying areas including raising (or lowering) earth, spreading in layers not exceeding 30 cm thick, watering ramming / rolling and finishing of required size, shape etc not exceeding 1.5 m high from base / natural ground level. (d) With reference to Clause 3.6 of MES Schedule Part-II on Serial Page NO. 21, it is clarified that measurement of the above item shall be of finished embankment / traverse of filled earth after consolidation / compaction and 5% deduction shall be made from measured and calculated volume to allow for increase in bulk.
INTERNAL WATER SUPPLY Supply & fixing two way bib cock with wall flange quarter turn (Low flow) 15/16 mm dia complete all as specified and directed.
Supply & fixing Pillar cock (Low flow) 15/16 mm dia complete all as specified and directed.
Supply & fixing bib cock with wall flange quarter turn (Low flow) 15/16 mm dia complete all as specified and directed.
Supply & fixing Hand shower (Health Faucet) with 1 meter long easy flex tube in chrome finish and wall hook with NRV (Back flow preventer) complete all as specified and directed.
Supply & fixing Angular Stop Cock 15 mm bore pf pipe (16 mm outer dia) with wall flange chromium plated stop valve complete all as specified and directed.
Supply & fixing Wall mixer with provision for overhead shower with 115mm long bend pipe on upper side, connecting legs & wall flanges complete all as specified and directed.
Supply & fixing Overhead shower140 mm dia round shape single flow with air effect (ABS body & face plate chrome plated) with rubit cleaning system 16mm dia complete all as specified and directed.
INTERNAL ELECTRIC SUPPLY M & L for point wiring with 2.5 sq mm (nominal area) 1100 Volts grade PVC insulated unsheathed multi stranded FRLSH multi stranded copper conductor cable, drawing through and including non metallic PVC rigid conduit medium grade, concealed in wall/ceiling/fixed to roof for 15 Amps switch socket outlet controlled by one switch along with PVC insulated multi stranded copper conductor FRLSH cable 2.5 sqmm for earth continuity conductor and connected to earth dolly including fixing of GI flush mounting box of suitable module and suitable inner plate and modular plate of suitable size. The modular plate shall be flushed to wall, fixed with SS screw, complete including necessary chase cutting and making good disturbed surfaces complete all as specified and as directed.
Supply & fixing of Modular type TV co axial socket outlet Modular in the modular MS/GI sheet box and cover plate including connections etc complete all as specified and directed.
Supply & fixing of Modular type RJ-11 telephone socket outlet Modular in the modular MS/GI sheet box and cover plate including connections etc double RJ-11 in one module complete all as specified and directed.
S&F LED light fitting 1x 10 W ,6500 K , 230 V, wall mounted Decorative ultra slim round profile LED lighting fixture with extruded polycarbonate diffuser, environmental friendly,ennergy efficient LED batten with integrated electronic driver, fixed on and including 02 Nos of PVC round/square block, screws etc complete with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.
S&F of GI pipe bracket up to 32 mm dia 0.9mm long and 2 set of clamps made out of 30x5 mm MS flat & fixed with anchor bolt suitable fo 1x35W LED security light fitting complete all as specified and directed.
Supply & fixing LED flood light fittings 210 watt 230 volt outdoor type with thermal management in multiple optics and equipped with IP 65 protection, with impact and corrosion resistant complete with driver and Lamp complete all as specified and directed.
Fabrication ,supply & fixing of GI pipe bracket up to 32 mm dia- 0.9m long & 2 set of clamps made out of 30x5mm ms flat & fixed with anchor bolt suitable for 1x210W LED flood light fitting complete all as specified and directed.
M & L for Flame proof point wiring controlled by one switch with 1.5 sq mm cable PVC insulated copper conductor multi stranded as per IS-694 FR cable controlled by one way switch, drawn with steel conduit concealed with all accessories incl 1.5 sqmm multi strand copper conductor cable (green colour) PVC insulated and unsheathed for earth continuity connected to common earth dolly and sunk cast pressed steel terminal box fixed flush to wall of not less than 1.6 mm thick for mounting of fittings such as switch complete all as specified and directed.
Supply and fixing of Flameproof LED lighting Glaze Pro 30 watt , 230 volt, wall mounted , screws etc complete with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.
Supply and fixing flame proof distribution board 8 way with MCBs complete all as specified and directed.
Supply and fixing Flame proof mettalic junction Box 4 way, Threaded type complete all as specified and directed.
Supply and fixing Flame proof flexible metalic Hose conduit 20 mm dia, 500 mm long complete all as specified and directed.
M& L for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including 01 no. 10 W LED bulb complete all as specified and directed.
SEWAGE DISPOSAL M&F for RCC Septic tank with conventional designed to carry sewage and silage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls , Base Slab , Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter for 150 users complete all as specified and directed.
M&F for RCC Septic tank with conventional designed to carry sewage and silage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design Mix in Walls , Base Slab , Baffle walls and Roof Slab including beams etc with Vent shaft , manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter for 50 users complete all as specified and directed.
M&L for on site Hume Pipe septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC (1:4:8) below foundation, Vent shaft, connection etc., complete for 10 users all as specified and directed.
M&L for Soakage wells excavation of size 2.4 M dia X 3 M deep, in any type of soil, foundation in PCC (1:3:6), walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M-25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size complete all as specified and directed.
M&L for Soakage wells excavation of size 1.8 M dia X 3 M deep, in any type of soil, foundation in PCC (1:3:6), walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M-25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size complete all as specified and directed.
M&L for Soakage wells excavation of size 1.2 M dia X 1.5 M deep, in any type of soil, foundation in PCC (1:3:6), walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M-25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size complete all as specified and directed.
EXTERNAL WATER SUPPLY S&F ductile iron fitting/ flange/ SS /bend/ reducer 80 to 200 mm dia of different size as required at site complete all as specified and directed.
Supply & Laying duclite iron (DI) pipe S/S class K-9 laid in trenches under floor / walls / columns etc. of bore size 150 mm, including rubber gasket push on joints complete all as specified and directed.
Supply & Laying duclite iron (DI) pipe SS class K-9 laid in trenches under floor / walls / columns etc. of bore size 100 mm, including rubber gasket push on joints complete all as specified and as directed.
Supply & Laying duclite iron (DI) pipe SS class K-7 laid under floor / walls / columns etc. of bore size 80 mm, including rubber gasket push on joints complete all as specified and as directed.( Note: Flange end from borewell to OHR)
M&L for construction of brick masonary valve pit of intemal dimensions 1000mm x 1000 mm x 1000 mm complete with PCC foundation 1:3:6, 100mm thickness full brick wall with CM 1:6, PCC coping 1:2:4 100 mm thickness on the top of brick wall and fixing hole fast of MS cover, rendering with CM 1:6 15mm thickness of internal surface and external surfaces upto 15 cm below GL and two coats of white wash, fabrication of 3.0 mm thick MS Sheet cover and angle iron frame made out of 40mm x 40mm x 6 mm MS angle iron and one side provided with hinge with locking arrangement with one no 50mm size lock with two nos keys and provision of lifting arrangement of cover & duly painted with two coats of black bituminous paint over a coat of red oxide primer induding necessary earth work and PCC work complete all as specified and directed.
M&L for construction of brick masonary valve pit of intemal dimensions 900mm x 900 mm x 900 mm complete with PCC foundation 1:3:6, 100mm thickness full brick wall with CM 1:6, PCC coping 1:2:4 100 mm thickness on the top of brick wall and fixing hole fast of MS cover, rendering with CM 1:6 15mm thickness of internal surface and external surfaces upto 15 cm below GL and two coats of white wash fabrication of 3.0 mm thick MS Sheet cover and angle iron frame made out of 40mm x 40mm x 6 mm MS angle iron and one side provided with hinge with locking arrangement with one no 50mm size lock with two nos keys and provision of lifting arrangement of cover & duly painted with two coats of black bituminous paint over a coat of red oxide primer induding necessary earth work and PCC work complete all as specified and directed.
M&L for construction of brick masonary valve pit of intemal dimensions 600mm x 600 mm x 600 mm complete with PCC foundation 1:3:6, 100mm thickness full brick wall with CM 1:6, PCC coping 1:2:4 100 mm thickness on the top of brick wall and fixing hole fast of MS cover, rendering with CM 1:6 15mm thickness of internal surface and external surfaces upto 15 cm below GL and two coats of white wash fabrication of 3.0 mm thick MS Sheet cover and angle iron frame made out of 40mm x 40mm x 6 mm MS angle iron and one side provided with hinge with locking arrangement with one no 50mm size lock with two nos keys and provision of lifting arrangement of cover & duly painted with two coats of black bituminous paint over a coat of red oxide primer induding necessary earth work and PCC work complete all as specified and directed.
S&F Cast Iron Air Valves 50 mm bore with double air Outlets, conforming to IS 14845 and fixing up in Cast Iron Water supply mains of size 50 mm bore complete all as specified and directed.
S&F Cast Iron Air Valves 80 mm bore with double air Outlets, conforming to IS 14845 and fixing up in Cast Iron Water supply mains of size 50 mm bore complete all as specified and directed.
S&F Cast Iron Air Valves 100 mm bore with double air Outlets, conforming to IS 14845 and fixing up in Cast Iron Water supply mains of size 50 mm bore complete all as specified and directed.
M & L for trial bore of 200 mm dia upto 200 mtr depth below ground level in any kind of soil strata including hard stone/boulder including electrc logging, MS cap, MS flat iron clamps, reducering socket etc. complete all as specified and directed. NOTE : Considering depth 80 RM, for 3 Nos Borewell as per CGWB report.
M & L development of trial bore by reaming upto 525 mm in following step upto 80 RM depth of each borewell from ground level by any suitable method as per soil condition and CGWB Report including disposal of spoil from the site complete all as specified and directed. (a) From 200 to 350 mm (b) From 350 mm to 450 mm (c ) From 450 mm to 525 mm
M&L for Electric logging of bore for precise delineation of granular zones & also the quality of ground water including report interpretation complete all as specified and directed. NOTE: Electric logging shall be carried out by any approved Govt Agency.
S&F MS centralising guide made out of 40x6 mm and 30 cm length MS flat iron all as specified in IS : 2800 (Part – 1) : 1991 complete all as specified and directed.
S&F well cap suitable for 200 mm bore housing pipe made out of 6 mm thick steel plate complete all as specified and directed. NOTE : After completion of the work well cap will be used to keep the bore well closed until the submersible pumping set is installed.
Supply only strata sample box with glass cover 3mm thick having internal dimension 1000x600x100mm made out of 20mm thick wrought Ist class hard wood shisham with hinges, hasp and staple including polishing complete with samples at various depth evenly 2 mtr interval met in boring including strata chart in duplicate complete all as directed and specified.
S&F bail plug of 200 mm internal dia threaded of minimum thickness 6 mm and 3 mtr long made up of mild steel and continuous welded by electric arc welding at both ends complete all as specified and directed.
M & L for yield test for the bore well by continuously pumping for 16 hours to determine safe pumping yield complete all as specified and directed.
M&L for development of tube well with air compressor of suitable capacity till sand/mud free water of potable quality is obtained & to achieve minimum discharge capacity of 36000 LPH (Compressor with accessories & tube etc. shall be arranged by the contractor) complete all as specified & as directed. .(Note: For 48 Hr for each borwell)
M&L for Development of tube well by over pumping 25% using suitable size diesel engine driven turbine pump after completion of item above, including yield testing for tube well as per IS requirements complete all as specified and directed. (24 Hrs for each borewell) NOTE :- Yield test of bore well shall be carried out in the presence of rep of Accepting Officer.
Supply, lowering and fixing / jointing 200 mm bore low carbon galvanised (LCG) strainer 3 mtr/ 6 mtr long min 6 mm thickness each conforming to IS 8110:2000 including mild steel socket threaded by electric arc welding both sides all as specified and directed with aperture 0.75 mm to 1 mm as per requirement complete all as specified and directed.
M&L for Testing of raw water & treated water from approved Govt lab for potability by doing chemical and bacteriological anaiysis as per norms of WHO and submission of test reports to the entire satisfacion of Engineer-in-Charge complete all as specified and directed.
S&F chain pulley block, triple spur gear, 2 ton capacity with 3 mtr lift, manually operated complete with hooks high tensile forged steel confirming to IS : 3815 and load confirming to IS: 6216 and hand chain to IS: 2429 (Part-I) complete all as specified and directed.
S&F steel rope flexible 8 mm dia with GI clamps, nuts,bolts, washer etc for fixing of submersible pump set complete all as specified and directed.
Supply, installation, testing and commissioning of liquid chlorine dozing system consisting of 40 ltr to 100 ltr PE/FRP tank with lid and level guage alongwith agitator, shaft and blades in SS-316 (FRP/Epoxy coated) / plastic mounted on tank complete all as specified and directed.
S&F flat submersible cable 3 core multi stranded copper conductor PVC insulated, water proof, ISI marked of size 10 sqmm for connecting from starter to bore well submersible pump sets complete all as specified and directed.
Supply, installation, testing and commissioning of multi stage submersible pump set vertical type (Open well type ) of suitable capacity with bronze impeller, directly coupled with motor, suitable for minimum head 60 meter and discharge min 1250 LPM operated on AC 3 phase, voltage range 300V-440V, 50 Hz. The motor casing shall be of stainless steel, pump shaft / motor shaft shall be of stainless steel, pump bowls shall be of high graded cast iron complete all as specified and directed. NOTE : The pump and motor shall comply to all the requirements of relevant IS.
S&F for Star delta starter three phase 20 HP or suitable capacity fully automatic in sheet metal enclosure for submersible pump with MCB, TPN, 32 A, 415 V,10 KA including single phase preventer, phase reserved protection, multi-functional meters, 3 Nos indicator Red, Yellow & Blue etc complete all as specified and directed.
Supply, installation, testing & commissioning of Iron Removal cum Pressure Filtration plant of 8000 GPH capacity complete with pressure filter,catalytic media,oxidation chamber, air compressor,back washing facility,pipelines, valves, pressure gauges. sampling clocks etc. including civil platform with RCC foundation complete all as specilied and directed.
Supply only CHLORINE TEST KIT with coloured sample & test-tubes complete with all testing fitments and OT solution in Rexene finish box complete all as specilied and directed.
Supply only PH test kit with coloured sample covered under BTB (range 6.0 to 7.0) or phenol red (range 6.8 to 8.4) & test-tubes with necessary fitments and 100 ml testing solution in rexene finish wooden box compleie all as specified and directed.
Supply only IRON Test Kit & test-tubes with necessary fitments and testing solution in rexene finish box complete all as specified and directed.
S&F LED Based Aviation Light, 7-11 watt nearest available in market including fixing on the roofup the over head water reservoir controlled by and including a digital timer complete all as specified and directed.
SECURITY LIGHT / STREET LIGHT S&F steel tubular swaged poles type 410 SP-31(9.0 meter long) Swan Neck Type complete with CI base plate and finial and single swan neck complete all as specified and directed. NOTE : Pole shall be procured in single length. Welding will not be allowed at site.
S&F steel tubular swaged poles Type 410 SP-31(9.0 meter long) Swan Neck Type complete with CI base plate and finial and double swan neck complete all as specified and directed. NOTE : Pole shall be procured in single length. Welding will not be allowed at site.
S&F junction box made out of polycarbonate with IP 55/IP 65 protection of suitable size including - 04 Nos cable terminal, 02 Nos polycarbonate cable gland , 01 Nos DIN rail and 01 No. MCB SP, 10 KA 6 Amps complete all as specified and directed.
S&F Astro timer, single channel with incoming MCB-TPN 4 Pole 415 Amp Capacity, Power Contactor 36 hrs 40 Amp capacity and MCB SPN 230 V 16 KA 10 Amp capacity for Bypass arrangement of timer including necessary DIN rail and enclosure complete all as specified and directed.
Supply and laying PVC insulated FR Copper conductor cable 3 X 1.5 sqmm cross sectional area in PVC conduit medium grade 20mm dia for connection from Junction box to street light/garden light complete all as specified and directed.
FIRE FIGHTING Supply and laying MS Pipes 300 mm bore, heavy grade with all fittings laid in floors or fixed to walls and ceilings etc of sizes complete all as specified and directed.
Supply and laying pipe ductile Iron , S/S including specials, Class “K-9” ,150 mm (6”) dia, for Fire Hydrent system including rubber gaskit push on joint complete all as specified and directed.
Supply and laying pipe ductile Iron , S/S including specials, Class “K-9” ,100 mm (4”) dia, for SWT including rubber gaskit push on joint complete all as specified and directed.
Supply and laying pipe ductile Iron , S/S including specials, Class “K-7” ,80mm (3”) dia, for SWT including rubber gaskit push on joint complete all as specified and directed.
S&F Dual plates CI wafer type check valve, 80 mm bore tested to pressure of 15Kg/ Sqcm with complete set all as specified and directed.
S&F Dual plates CI wafer type check valve, 150 mm bore tested to pressure of 15Kg/ Sqcm with complete set all as specified and directed.
S&F pumping sets, centrifugal self-priming type, electric driven, supply and Install complete up to 5 HP inclusive of starter and PCC foundation for fire hose washing purpose complete all as specified and directed.
S&F brass primium pack brass flot valve with flexible rod and nitrile rubber seat screwed 25mm complete all as specified and directed.
EXTERNAL ELECTRIFICATION Supply and installation of 4 Way Ring Main Unit (RMU) (3V + IC), one incoming, three outgoing SF6 filled load break switch each of outdoor type of rating 630 Amp Aluminium bus bas with a fault clearing capacity of 21 KA for 3 sec, rated voltage 12 KV, operational voltage – 11 KV, frequency – 50 Hz totally enclosed ring main unit with IP 67 protection for SF6 tank and IP 55 protection for outdoor enclosure with self powered microprocessor based numerical relay with over current and earth fault protection. Entire RMU should be tested for internal arc test of 21 KA for Sec as per IEC-62271 -200 standards including installation and testing, PCC foundation as per OEM including the followings complete all as specified and as directed. (a) HT 11 KV, 630 Amps, 350 MVA, 21 KA for secs, SF6 insulated Non-extensible compact Switchgear consisting of 01 No. fixed manual Vacuum Circuit breaker as Incomer and 01 No manual load break switch as Outgoing and 02 No. fixed manual Vacuum Circuit Breaker as Outgoing with microprocessor based self powered relay in SF6 insulated stainless steel enclosure, with series trip, self powered microprocessor based numerical over current delay (IDMT + Inst) protection along with Class 1.0 Metering with interconnection between HT switchgear and transformer with Cable 240 Sqmm 3 Core aluminium unarmoured XLPE cable – 01 Set. (b) 11 KV single phase indoor resin cast PT of ratio 11 kv/rt 3/110 V/rt3,lass 0.5-3, Burden 5VA – 50VA, insulation level 28/75 kV, voltage factor 1.2 const and 1.9 for 30 sec, conforming to IS-3156 – 01 Set. (c) 11 KV single phase indoor resin cast CT of appropriate ratio as per manufacturer’s design, based on load, class 0.5, 5P10, Burden as per manufacturer’s design, insulation level 28/75, as per IS-2705 – 01 Set. NOTE : RMU shall be procured from the OEM only. Any franchising’s/ outsourcing of OEM’s manufacturer’s shall not be allowed.
Supply and installation of 5 Way Ring Main Unit (RMU) (4V + IC), one incoming, four outgoing SF6 filled load break switch each of outdoor type of rating 630 Amp Aluminium bus bas with a fault clearing capacity of 21 KA for 3 sec, rated voltage 12 KV, operational voltage – 11 KV, frequency – 50 Hz totally enclosed ring main unit with IP 67 protection for SF6 tank and IP 55 protection for outdoor enclosure with self powered microprocessor based numerical relay with over current and earth fault protection. Entire RMU should be tested for internal arc test of 21 KA for Sec as per IEC-62271 -200 standards including installation and testing, PCC foundation as per OEM including the followings complete all as specified and as directed. (a) HT 11 KV, 630 Amps, 350 MVA, 21 KA for secs, SF6 insulated Non-extensible compact Switchgear consisting of 01 No. fixed manual Vacuum Circuit breaker as Incomer and 01 No manual load break switch as Outgoing and 03 No. fixed manual Vacuum Circuit Breaker as Outgoing with microprocessor based self powered relay in SF6 insulated stainless steel enclosure, with series trip, self powered microprocessor based numerical over current delay (IDMT + Inst) protection along with Class 1.0 Metering with interconnection between HT switchgear and transformer with Cable 240 Sqmm 3 Core aluminium unarmoured XLPE cable – 01 Set. (b) 11 KV single phase indoor resin cast PT of ratio 11 kv/rt 3/110 V/rt3,lass 0.5-3, Burden 5VA – 50VA, insulation level 28/75 kV, voltage factor 1.2 const and 1.9 for 30 sec, conforming to IS-3156 – 01 Set. (c) 11 KV single phase indoor resin cast CT of appropriate ratio as per manufacturer’s design, based on load, class 0.5, 5P10, Burden as per manufacturer’s design, insulation level 28/75, as per IS-2705 – 01 Set. NOTE : RMU shall be procured from the OEM only. Any franchises/ outsourcing of OEM’s manufacturer’s shall not be allowed.
Supply, installation, testing and commissioning of Compact Package type sub-station (CSS) confirming to 15-14786 (2000) and IEC-1330 (1995), outdoor, plinth mounted type (rates, include for PCC foundation/ brick foundation as per manufacturers instructions) comprising following components interconnected with one another, including required interconnection with suitable size cable / bus bar and internal earthing connections complete as required as per following specifications:- 11 KV compact ready to use and factory fitted (No assembly at site) sub-station, outdoor type, designed for natural cooling / forced cooling as per requirement,having type tested equipment's, comprising distribution transformer and VCB and LT panels enclosed in suitable enclosure, interconnection between VCB & transformers using suitable size cable and transtormer to LT switch gear using copper bus bar /suitable size cables factory built ready for connection type, internal earthing, factory completed and other associated equipment's etc. complete as required conforming to detailed specifications as under :- The enclosure shall have modular construction using CRCA / Alu zinc/Gl Sheets not less than 2 mm thick, CPRI approved as per standard manuiacturing, intenal arc tested and shall be painted with suitable water Proof paint from the exterior. (a) The enclosure for HT and LT switchgear shall be provided with IP 54 as ingress protection. The transformer compartment will have IP-23 as ingress protection. The transformer compartment used shall be specially designed for low losses and hermetically sealed. The combination ot compact substation shall be as per details given below:- Item Continued as 16.77 to 16.78
TRANSFORMER :- One No. 11 KV / 433 V, 250 KVA. 3-Phase. DYN 11, +/- 7.5 in steps of 2.5% at line end of HV winding. off load tap changer, dry type. as per standard manufacturing as recommended by manufacturer with copper winding & standard fittings as specified, core type double wound. The transformer shall be manufactured as per latest IS 2026 and other relevant IS provisions and shall be mounted inside compact sub-station enclosure. The winding shall have class F insulation and the losses shall be within the tolerarnce limits as per relevant IS. (b) VCB BREAKER:- 11 KV, 630 Amps vacuum circuit breaker - 01 No. in stainless steel / metallized cast resin tank with microprocessor based numerically relay, dedicated to CTs for protection of transformer. This shall comprise of the following:- (i) Vacuum circuit breaker 630 Amp, 11 KV, 21 KA for 3 sec, 3 Phase. 50 Hz. (ii) Integral earthing switch with making switch. (iii) Energy trip push button. (iv) 230V / 110 AC shunt trip coil for external trip signal. (v) Live cable indicating LEDs energized through capacitive voltage dividers. (vi) Right angle terminal protectors / boots. (vii) Cable box for incoming shall be suitable for terminating, HT XLPE underground cable, 120 Sqmm, 3-Core (Earthed). (viii) Microprocessor based IDMT relay for over current, short circuit and earth fault protection including suitable power pack unit capable of 5 trips at a time and suitable battery charger. (ix) Required auxiliary relay for WRl (Winding Temperature indication), with alarms etc. (x) One No. Potential transformer (PT) three phase dry type (resin cast) draw out type 11 KV / 110 V, 2.5 VA burden accuracy class 0.5 with HT & LT HRC fuses for primary and secondary complete all as per IS -3156 - 01 Set.
(xi) CT ring core type 50/1+1, and accuracy class 1.0 tor metering and class 5P10 for protection. (xii) Digital intelligent panel meter indicating line/phase current, line /phase voltage, power factor, KVAR, KVA, frequency, wave forms,THD etc with accuracy class 0.5 (c) LT PANEL (MOUNTED INSIDE COMPACT PACKAGE TYPE SUBSTATION ENCLOSURE) :- LT indoor 433 V panel with copper bus bar TPN, 800 Amps, 50KA with fabrication using 2 mm thick CRCA sheets with ingress protection IP 54 conforming to IS 5039/ IS 8623 and relevant IS standards, CPRI approved complete with wiring as follows:- INCOMING: - Air circuit breaker, 630 Amps, Microprocessor based, 4 Pole, 3-Phase, 440 V, 50 Hz, breaking capacity 50 KA, (1 sec) - 01 No. INDICATING PANEL:- The indicating panel of incomer shall be provided with the following :- (i) Digital type multi function meter to show KWH, KVA, PF, current, voltage etc including suitable CT. (ii) Three Nos phase indicating lamps LED type. OUTGOING:- (i) MCCB. 160 Amps, 3 Pole, 16 KA with thermal release, 415 V, 50C/S, AC - 01 No. (ii)MCCB, 200 Amps, 3 Pole, 25 KA with thermal release, 415 V, 50 C/S,AC-01 No. (iii)MCCB, 315 Amps, 3 Pole, 25 KA with thermal release, 415 V, 50 C/S, AC-02 No. NOTE : CSS shall be procured from the OEM only. Franchising / outsourcing manufacturer of OEM shall not be allowed.
Supply, installation, testing and commissioning of Compact package type sub-station (CSS) confirming to 15-14786 (2000) and IEC-1330 (1995), outdoor, plinth mounted type (rates, include for PCC foundation/ brick foundation as per manufacturers instructions) comprising following components interconnected with one another, including required interconnection with suitable size cable / bus bar and internal earthing connections complete as required as per following specifications:- 11 KV compact ready to use and factory fitted (No assembly at site) sub-station, outdoor type, designed for natural cooling / forced cooling as per requirement,having type tested equipment's, comprising distribution transformer and VCB and LT panels enclosed in suitable enclosure,interconnection between VCB & transformers using suitable size cable and transtormer to LT switch gear using copper bus bar /suitable size cables factory built ready for connection type, internal earthing, factory completed and other associated equipment's etc. complete as required conforming to detailed specilications as under :- The enclosure shall have modular construction using CRCA / Alu zinc/Gl Sheets not less than 2 mm thick, CPRI approved as per standard manuiacturing, intenal arc tested and shall be painted with suitable water Proof paint from the exterior. (a) The enclosure for HT and LT switchgear shall be provided with IP 54 as ingress protection. The transformer compartment will have IP-23 as ingress protection. The transformer compartment used shall be specially designed for low losses and hermetically sealed. The combination ot compact substation shall be as per details given below:- Item Continued as 16.80 to 16.81
TRANSFORMER :- One No. 11 KV / 433 V, 315 KVA. 3-Phase. DYN 11, +/- 7.5 in steps of 2.5% at line end of HV winding. off load tap changer, dry type. as per standard manufacturing as recommended by manufacturer with copper winding & standard fittings as specified, core type double wound. The transformer shall be manufactured as per latest IS 11171/1985 and other relevant IS provisions and shall be mounted inside compact sub-station enclosure. The winding shall have class F insulation and the losses shall be within the tolerarnce limits as per relevant IS. (b) VCB BREAKER:- 11 KV, 630 Amps vacuum circuit breaker - 01 No. in stainless steel / metallized cast resin tank with microprocessor based numerically relay, dedicated to CTs for protection of transformer. This shall comprise of the following:- (i) Vacuum circuit breaker 630 Amp, 11 KV, 21 KA for 3 sec, 3 Phase. 50 Hz. (ii) Integral earthing switch with making switch. (iii) Energy trip push button. (iv) 230V / 110 AC shunt trip coil for external trip signal. (v) Live cable indicating LEDs energized through capacitive voltage dividers. (vi) Right angle terminal protectors / boots. (vii) Cable box for incoming shall be suitable for terminating, HT XLPE underground cable, 120 Sqmm, 3-Core (Earthed). (viii) Microprocessor based IDMT relay for over current, short circuit and earth fault protection including suitable power pack unit capable of 5 trips at a time and suitable battery charger. (ix) Required auxiliary relay for WRl (Winding Temperature indication), with alarms etc. (x) One No. Potential transformer (PT) three phase dry type (resin cast) draw out type 11 KV / 110 V, 2.5 VA burden accuracy class 0.5 with HT & LT HRC fuses for primary and secondary complete all as per IS -3156 - 01 Set.
(xi) CT ring core type 50/1+1, and accuracy class 1.0 tor metering and class 5P10 for protection. (xii) Digital intelligent panel meter indicating line/phase current, line /phase voltage, power factor, KVAR, KVA, frequency, wave forms,THD etc with accuracy class 0.5 (c) LT PANEL (MOUNTED INSIDE COMPACT PACKAGE TYPE SUBSTATION ENCLOSURE) :- LT indoor 433 V panel with copper bus bar TPN, 800 Amps, 50KA with fabrication using 2 mm thick CRCA sheets with ingress protection IP 54 conforming to IS 5039/ IS 8623 and relevant IS standards, CPRI approved complete with wiring as follows:- INCOMING: - Air circuit breaker, 630 Amps, Microprocessor based, 4 Pole, 3-Phase, 440 V, 50 Hz, breaking capacity 50 KA, (1 sec) - 01 No. INDICATING PANEL:- The indicating panel of incomer shall be provided with the following :- (i) Digital type multi function meter to show KWH, KVA, PF, current, voltage etc including suitable CT. (ii) Three Nos phase indicating lamps LED type. OUTGOING:- (i) MCCB. 160 Amps, 3 Pole, 16 KA with thermal release, 415 V, 50C/S, AC - 01 No. (ii) MCCB, 200 Amps, 3 Pole, 25 KA with thermal release, 415 V, 50 C/S,AC-01 No. (iii) MCCB, 315 Amps, 3 Pole, 25 KA with thermal release, 415 V, 50 C/S, AC-02 No NOTE : CSS shall be procured from the OEM only. Franchising / outsourcing manufacturer of OEM shall not be allowed.
Supply only Electric rubber hand gloves 11 KV, ISI marked complete all as specified and directed.
Supply and fix outdoor type LT junction box with 4 Nos. aluminium busbar, 200 Amps capacity with sheet metal enclosure as specified and directed.
Supply, Installation, testing and commissioning of silent built in within an acoustic enclosure diesel engine driven generating set water cooled including AMF panel for standby power supply 415 volts, 03 Phase, 4 wire,50 cycles / sec, 50 KVA (40.0 KW) at 0.8 power factor complete with alternator directly coupled to diesel engine, mounted on common base frame & complete with alternator directly coupled to diesel engine, mounted on common base frame & battery 12 volts 150/180 AH lead acid type, battery leads, sound proof canopy etc. with feathers for automatic shutdown in the event of a circuit failure condition arising from low oil pressure, high coolant temperature, over speed etc. & PSO500 genset controller with the following undermentioned features complete all as specified and directed:- a) 16 character x 2 line alphanumeric b) LCD display with LED backlight. c) Operator interface. d) Suitable to provide a record of most recent fault conditions & fault history. e) Complete alternator data viz, voltage Ph-ph, ph-neutral, KVA, frequency etc. f) Complete engine date viz, starting battery voltage, engine temp, engine running hours, engine oil pressure etc. g) Control including provn of service adjustment & calibration of DG control functions. GENSET SPECIFICATIONS PRIME MOVER RATING : 50 KVA/40.0 KW CURRENT RATING : 70A NO OF PHASES ; 03 POWER FACTOR : 08 (LAG) Item Continued as 16.85
Supply, Installation, testing and commissioning of silent built in within an acoustic enclosure diesel engine driven generating set water cooled including AMF panel for standby power supply 415 volts, 03 Phase, 4 wire,50 cycles / sec, 150 KVA (120 KW) at 0.8 power factor complete with alternator directly coupled to diesel engine, mounted on common base frame & complete with alternator directly coupled to diesel engine, mounted on common base frame & battery 12 volts 150/180 AH lead acid type, battery leads, sound proof canopy etc. with feathers for automatic shutdown in the event of a circuit failure condition arising from low oil pressure, high coolant temperature, over speed etc. & PSO500 genset controller with the following undermentioned features complete all as specified and directed:- a) 16 character x 2 line alphanumeric b) LCD display with LED backlight. c) Operator interface. d) Suitable to provide a record of most recent fault conditions & fault history. e) Complete alternator date viz, voltage ph, ph-neutral, KVA, frequency etc. f) Complete engine date viz, starting battery voltage, engine temp, engine running hours, engine oil pressure etc. g) Control including provn of service adjustment & calibration of DG control functions. GENSET SPECIFICATIONS PRIME MOVER RATING : 150 KVA/120 KW CURRENT RATING : 222.64 NO OF PHASES ; 03 POWER FACTOR : 08 (LAG) Item Continued as 18.01
M&L for cable route indicator using RCC post 1.20 mtr long, top 100 x 100 mm & bottom 200 x 200 mm, with height not less than 50 cm above GL with engraved marking " LT CABLE " in bold letters during refilling of the trench complete all as specified and directed. NOTE : The spacing between two consecutive cable route indicators shall not be more than 50.0 meters & also shall be provided at each & every bend or corner.
Supply, installation, testing and commissioning of out door type LT feeder piller box of suitable size, pedastal mounted, CPRI type tested factory made totally enclosed, dust and vermin proof, double leaf shutter in front and single leaf shutter in rear side made of 3.15mm thick CRCA sheet, framing with 50 x 50 x 6 mm thick MS angle iron and legs of size 0.5m long . duly fabricated and having proper looking amangement in both front and rear door with 4 side slanting canopy duly projected and painted to both internal and Extemal surfaces with powder coating paint in heat process of sheet and suitable for 500 volts, 50 Hz, 3 phase 4 wire system and comprising with and induding following accessories and mounted on suitable PCC platform & necessary foundation complete with the following accessories all as spedtied and directed : Panel- 1 BUSBAR:- 200 Amps rated copper bus bar TPN duly insulated with coloured PVC sleeve as per standard colour code and rigidly mounted on bakelite/DMC insulator bus bar support (Square/round insulators of suitable size and good insulation resistance Item Continued as 16.90
Supply, installation, testing and commissioning of out door type LT feeder piller box of suitable size, pedastal mounted, CPRI type tested factory made totally enclosed, dust and vermin proof, double leaf shutter in front and single leaf shutter in rear side made of 3.15mm thick CRCA sheet, framing with 50 x 50 x 6 mm thick MS angle iron and legs of size 0.5m long . duly fabricated and having proper looking amangement in both front and rear door with 4 side slanting canopy duly projected and painted to both internal and Extemal surfaces with powder coating paint in heat process of sheet and suitable for 500 volts, 50 Hz, 3 phase 4 wire system and comprising with and induding following accessories and mounted on suitable PCC platform & necessary foundation complete with the following accessories all as spedtied and as directed : Panel-2 BUSBAR:- 200 Amps rated copper bus bar TPN duly insulated with coloured PVC sleeve as per standard colour code and rigidly mounted on bakelite/DMC insulator bus bar support (Square/round insulators of suitable size and good insulation resistance. Item continued as 16.92
Supply, installation, testing and commissioning of out door type LT feeder piller box of suitable size, pedastal mounted, CPRI type tested factory made totally enclosed, dust and vermin proof, double leaf shutter in front and single leaf shutter in rear side made of 3.15mm thick CRCA sheet, framing with 50 x 50 x 6 mm thick MS angle iron and legs of size 0.5m long . duly fabricated and having proper looking amangement in both front and rear door with 4 side slanting canopy duly projected and painted to both internal and Extemal surfaces with powder coating paint in heat process of sheet and suitable for 500 volts, 50 Hz, 3 phase 4 wire system and comprising with and induding following accessories and mounted on suitable PCC platform & necessary foundation complete with the following accessories all as spedtied and as directed : Panel-3 BUSBAR:- 200 Amps rated copper bus bar TPN duly insulated with coloured PVC sleeve as per standard colour code and rigidly mounted on bakelite/DMC insulator bus bar support (Square/round insulators of suitable size and good insulation resistance. Item Continued as 16.94
Supply, installation, testing and commissioning of out door type LT feeder piller box of suitable size, pedastal mounted, CPRI type tested factory made totally enclosed, dust and vermin proof, double leaf shutter in front and single leaf shutter in rear side made of 3.15mm thick CRCA sheet, framing with 50 x 50 x 6 mm thick MS angle iron and legs of size 0.5m long . duly fabricated and having proper looking amangement in both front and rear door with 4 side slanting canopy duly projected and painted to both internal and Extemal surfaces with powder coating paint in heat process of sheet and suitable for 500 volts, 50 Hz, 3 phase 4 wire system and comprising with and induding following accessories and mounted on suitable PCC platform & necessary foundation complete with the following accessories all as specified and directed: Panel-4 BUSBAR:- 200 Amps rated copper bus bar TPN duly insulated with coloured PVC sleeve as per standard colour code and rigidly mounted on bakelite/DMC insulator bus bar support (Square/round insulators of suitable size and good insulation resistance. Item Continued as 16.96
Supply, installation, testing and commissioning of out door type LT feeder piller box of suitable size, pedastal mounted, CPRI type tested factory made totally enclosed, dust and vermin proof, double leaf shutter in front and single leaf shutter in rear side made of 3.15mm thick CRCA sheet, framing with 50 x 50 x 6 mm thick MS angle iron and legs of size 0.5m long . duly fabricated and having proper looking amangement in both front and rear door with 4 side slanting canopy duly projected and painted to both internal and Extemal surfaces with powder coating paint in heat process of sheet and suitable for 500 volts, 50 Hz, 3 phase 4 wire system and comprising with and induding following accessories and mounted on suitable PCC platform & necessary foundation complete with the following accessories all as spedtied and directed: Panel-5 BUSBAR:- 200 Amps rated copper bus bar TPN duly insulated with coloured PVC sleeve as per standard colour code and rigidly mounted on bakelite/DMC insulator bus bar support (Square/round insulators of suitable size and good insulation resistance. Item Continued as 16.98
Supply, installation, testing and commissioning of out door type LT feeder piller box of suitable size, pedastal mounted, CPRI type tested factory made totally enclosed, dust and vermin proof, double leaf shutter in front and single leaf shutter in rear side made of 3.15mm thick CRCA sheet, framing with 50 x 50 x 6 mm thick MS angle iron and legs of size 0.5m long . duly fabricated and having proper looking amangement in both front and rear door with 4 side slanting canopy duly projected and painted to both internal and Extemal surfaces with powder coating paint in heat process of sheet and suitable for 500 volts, 50 Hz, 3 phase 4 wire system and comprising with and induding following accessories and mounted on suitable PCC platform & necessary foundation complete with the following accessories all as spedtied and directed: Panel-6 & 7 BUSBAR:- 200 Amps rated copper bus bar TPN duly insulated with coloured PVC sleeve as per standard colour code and rigidly mounted on bakelite/DMC insulator bus bar support (Square/round insulators of suitable size and good insulation resistance. Item Continued as 17.00
M & L for electric supply tripping system with remote manual operation of MCCBs Locted at Store area from the Master control panel located at main gate with the following including connection, testing complete all as specified and directed :- (a) Shunt release system, AC 230 Volts-01 No. (b) Sheet metal enclosure for Shunt Release system -01 No. (c) UG Control cable 2 Core Note :- Cable will be measured and paid seperately.
M&L for Boring hole under the existing road or PCC hard standing without damaging the surface of the road suitable for inserting upto 150 mm bore pipe at a depth 0.75 to 1.0 mtr complete all as specified and directed.
SUMMER APPLIANCES & LV SERVICES Supply and fix refrigerator, electric driven (single phase), capacity 190 Litres, BEE 5 star rated complete all as specified and directed.
Supply and fix Deep freezer hard top up to 320 litre capacity having single door, 5 star rating complete all as specified and directed.
Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity of 2 KVA complete all as specified and directed.
Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity of 3 KVA complete all as specified and directed.
PROVISIONAL LUMP SUM
Provn of following items complete all as directed by the Engineer-in-Charge. (i) RCC Dunnage Block of Size 300 mm x 300 mm x 200 mm - 10400 Nos. (ii) Provn of Fire Symbol Board - 08 Nos. (iii) Provn of Symbol Explanation Board - 01 Nos. (iv) Provn of Shed Number Board - 08 Nos. (v) Provn of Display Board - 08 Nos. TOTAL AMOUNT = ₹ 74,90,000.00 Add/deduct__________%(___________percent) ₹____________ Above/below Total cost is at par SSR-2020 rate, Bidder to quote total amount after considering percentage addition/deduction thereto to cover market variation over head and profit etc.
NARSINGH DEVELOPERS LLP
M/S ALLIED CONSTRUCTION
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid