Construction of Working Women Hostel at Ind. Area Chanour, Distt. Kangra (HP) SH- Providing Water Supply and Sanitary Installation, C/o Septic Tank with Soak Pit, Rain harvesting tank and site development.

Amount

Excavation in foundations, trenches etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work, pick jumper blasting work, blasting work in soft and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/ wedging out of rocks (where blasting is prohibited) and pumping or bailing watering /dewatering up to any lift stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in layers when required into plinth sides of foundations consolidation each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed within any leads including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in- Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to all floor level 1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size) including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Centering and shuttering including strutting, propping etc. and removal of form work for including carriage of material with in all leads and lifts :- (a) Lintels, beams, plinth beams, girders, bressumers and cantilevers

b) Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc

c) Suspended floors, roofs, landings, balconies and access platform

d) Edges of slabs and breaks in floors and walls Under 20 cm wide

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size) including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 Cement : 3 coarse sand) : 6 graded stone aggregate 20 mm nominal size) including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure in: Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and applying 15 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) on brick/stone masonry wall surfaces, including preparation of surface, scaffolding, curing, and finishing smooth and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including scaffolding, surface preparation, and all other incidental works, complete in all respects as per the direction of the Engineer-in-Charge.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade Two or more coats on new work including surface preparation, scaffolding, and all other operations required for proper completion of the work, complete in all respects as per the direction of the Engineer-in-Charge.

Providing and laying 80mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing weapholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Excavating, supplying, and filling of local earth (including royalty) by mechanical transport up to a lead of 5 km, including spreading, watering, and ramming the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation, etc., complete in all respects as per the direction of the Engineer-in-Charge.

15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm thick with 20 mm nominal size stone aggregate including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Making soak pit of size 2.5 metre diameter and 3.0 metre depth, with 45 cm x 45 cm dry brick honeycomb shaft constructed using common burnt clay F.P.S. (non-modular) bricks of class designation 7.5, including provision of 100 mm diameter S.W. drain pipe of 1.8 metre length, filling the surrounding space with brick bats up to full depth excavation, backfilling, and restoration of surface, complete in all respects as per the direction of the Engineer-in-Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China size 550x400 mm with a 15 mm CP Brass single hole basin mixer including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board 510x1040 mm bowl depth 250 mm including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing & fixing Sink Mixer with Swinging Casted Spout (Table Mounted Model) with 450mm long Copper Pipes & Braqss Nuts including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing toilet paper holder C.P. Brass including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing 600 x 400 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15mm nominal diameter including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge . (A) 20 mm nominal outer dia Pipes

(B) 32 mm nominal outer dia Pipes

Supplying & fixing CPVC ball valve, size 32 mm (1¼″), full-port, solvent-weld ends, lead-free, PTFE seats, EPDM/FPM seals, 100 psi @ 82 °C, with polypropylene lever handle, including cutting & jointing complete as per direction of Engineer-in-Charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes all necessary accessories such as overflow pipe connection, PVC float valve, tank nipple, etc., but without base support for tank including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing square mouth SW Gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing, laying and jointing 200 mm dia HDPE pipe, PE-100 grade, SDR-26 for underground non-pressure sewerage, including excavation, bedding, jointing, testing, and backfilling including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge , (i) Single socketed pipes. (A) 75 mm diameter

(B) 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge. (A) 75 mm bend

(B) 110 mm bend

© Single tee without door 75x75x75 mm

(D) Single tee without door 110x110x110 mm

(E) Single tee with door 110x110x110 mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge . (A) 75 mm

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing PVC Cowl 110 mm dia including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and Fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 75 mm including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing 100 mm sand cast Iron grating for gully trap including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws 750mm x 20mmm including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Constructing Manhole with RCC top slab 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) mixture foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing all complete as per standard design: with Pre-cast R.C.C. Cover and frame(heavy duty HD- 20 grade designation) 560mm internal diameter conforming to I.S.12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominalsize) including centering, shuttering all complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge . (A) Inside size 800 x 800mm and 500mm deep With 200 mm thick walls of RCC 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) including complete formwork and reinforcement with 10 mm bars not exceeding 150 mm C/C both Ways in walls, bed & Slab

(B) Inside size 800 x 800mm and 1000mm deep With 200 mm thick walls of RCC 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) including complete formwork and reinforcement with 10 mm bars not exceeding 150 mm C/C both Ways in walls, bed & Slab

A.R. Traders (BID ID -562368)