SPECIAL REPAIRS TO BLDG NO NP 52 2 AND CERTAIN MINOR WORKS AT MIL STN DHRANGADHRA

Amount

Surface excavation not exceeding 30cm and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and directed.

M&L for excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. and getting out hard/dense of soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layer not exc 25 cm with soil obtained from excavation complete all as specified and directed.

M&L for providing dry river sand as in sand as in floors or foundation including watering and consolidation (50mm thick sand cushioning) all as directed. Note: Depth after punning shall be measured and paid.

Removing excavated material to a distance exc. 1.5 Km but not exc. 5.0 KM from starting point out side MD land complete all as specified and directed.

M&L for hard core of gauge not exc. 63mm deposited spread and levelled in layers not exc. 15 cm thick, spread, levelled and rammed to a true surface including watering complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-2, using 40 mm graded stone aggregate as in bed blocks complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D-2, as in foundation filling and mass concrete complete all as specified and directed.

M&L for cement concrete (1:3:6), type C-1, using 20mm graded stone aggregate in coping and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry Type B1 1:2:4 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry Type B1 1:2:4 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar 1:4 complete all as specified and directed.

M&L for precast reinforced cement concrete, type B1, 1:2:4 (20mm graded stone aggregate) as in beams, cantilevers, RCC bands, bressummers, lintels over 1.5m span set in cement mortal 1:6 complete all as specified and directed.

Cutting chases in stone concrete blocks of slab walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

M&L for walling of random rubble stone masonry, uncourced, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified and directed.

M&L for walling of random rubble stone masonry, uncourses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) but except stone complete all as specified and directed.

M&L for form work to sides and soffit of floor beams, beams haunchingss, girders, brussummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc and rough finished surfaces of concrete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood factory made, plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F, factory made, 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Taking down chowkats or frames of any description n.exc 1.5sq.m each (without taking off shutters from the frames) removing to store complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5sq.m but not exc. 4sq.m each complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, PVC insulation panels 10mm thick with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium /G.I./M.S. as per specification and drawing complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 250mm and fixed complete all as specified and directed.

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300mm and fixed complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

M&L for 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F, 100mm double action spring hinges, mild steel with steel wire spring, stove enamelled, black complete all as specified and directed.

S&F, extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel springcomplete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F, in repair, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F, in repair, 25mm dia, powder coated, fancy type, aluminium decorative tubular curtain rod with decorative ball type side brackets complete all as specified and directed.

S&F, 20mm dia, stainless steel, fency type, tubular curtain rod fix on decorative brackets with decorative globe at both end complete all as specified and directed.

S&F in repair, stainless steel, fancy type Brackets decorative with fancy type globe at both end curtain rod for 20mm dia curtain rod complete all as specified and directed.

S & F in repairs of anodised aluminium grill made with 6 mm bars made to shape, DG-104 including U/F/H aluminium channel/sections complete all as specified and directed (Make :- Jindal / Hindalco / Ajit India) Note :- (i) Fabrication work shall be got done from approved fabricator of manufacturer of alluminium sections. (ii) Sample of grill shall got approved by the GE in writing.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars, shouldered and/or riveted, or forged into spikes, framed guard bars etc and similar work conforming to Fe-290 (Gde-E-165) including applying one shop coat of red oxide primer complete all as specified and directed.

Febrication only, Mild steel bolts, purpose made with hexagonal or square head one end and screwed the other, or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut. exc 30cm long dia of neck in exc 12mm but n.exc 20mm complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S&F mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, inclding cranking, bendiing spirally for hooping for columns, hooking ends and biinding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

S&F, mild steel, rolled sections (Fe 410-W (Gde-E-250) quality-A) as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates including one shop coat of zinc chrome primer complete all as specified and directed.

S&F mild steel work in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment conforming to (Fe 410-W (Gde-E-250) quality-A) complete all as specified and directed.

S&F, MS angle iron Fe-410-W (Gde-E-250) quality A in framed work for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc and including applying one shop coat of red oxide primer complete all as specified and directed.

M&L for rolled mild steel angle iron work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

S&F, Aluminium anodised windows/ ventilators with one or more rebates including joining cleat for fixing etc complete with frames, shutters and grills of size directed by Engineer-in-charge including handles, tower bolts, grills, etc complete all as specified and directed. Note:- sheet glass, wire cloth, lock, etc shall be measured and paid seperately.

S&F, anodised aluminium snap grid frame work for false ceiling complete all as specified and directed.

S&F, pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, pre-painted galvalume aluminum zinc coating GI based manglore pattern corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, in repair, false ceiling, at any height, 600 x 600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH - 99 Classic lite' with suspension system complete all as specified and per manufacturer's instruction. Make : Armstrong or equivalent as approved by GE.

M&L for 16-18mm thick black granite stone slab (one slab in size) machine cut as in skirting/dado, cooking platform, jams, pillars, windows cills and the like laid over and including 10mm thick screed bed or backing coat in cement mortar (1:4) and jointed with grey cement alurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement,complete all as specified and as directed.

M&L for 75mm thick cement concrete 1:4:8 type D2, using 20mm graded stone aggregate as in subbase floor finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete as specified and directed.

M&L for Non-skid joint free coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for coloured glazed ceramic tiles of size 450x350x7mm thick on vertical surface such as skirting/dado, incl highlighter patterns complete set and jointed in net cement slurry and pointed in colour cement to match ver 10 mm thick backing coat in CM 1:3 complete all as specified and directed.

M&L for joint free coloured glazed ceramic tiles of size 300x200/ 350x250x7mm/ 450 x 350 x 7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match ver 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed in CM 1:3 complete as specified and directed.

M&L for vitrified ceramic tiles light shade 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm but n.exc 0.42 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for vitrified ceramic tiles light shade 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm but n.exc 0.42 sqm in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed

M&L for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade including 25mm thick (compacted thickness) sand cushion below paver blocks including takingout old paver block floor complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish of the premisses complete all as specified and directed.

M&L for 10mm thick rendering in CM (1:3) to concrete surface of ceiling finished even and smooth all as specified and directed

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces or surface other than fair faces of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surface other than fair faces of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces or surface other than fair faces of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparing of new plastered or un-plastered wall surfaces and applying two coats of oil bound distemper over and including chalk whiting on plastered surfaces, preparatory to distempering complete all as specified and directed.

M&L for preparing of new plastered or un-plastered surfaces and applying two coats of oil bound distemper over a coat of primer over and including wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

S&F, 4.8 / 5 mm thick Sheet glass, ordinary quality ,in square exc. 0.5 Sqm in each pane with necessary rubber gaskets complete all as specified and directed.

S&F, 3 mm thick figured glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for anodised aluminium handles 75mm size of approved pattern for aluminium windows complete all as specified and directed.

M&L for anodised aluminium tower bolt 75mm size of approved pattern for aluminium windows complete all as specified and directed.

S&F, in repair, hot & cold wall mixer, brass chromium plated with complete fitting set, screwed for 15mm bore GI Pipe complete all as specified and directed as per Cat Part No CON-167 KNB of jaquar of equivalent make as approved by GE from the makes specified in Appx 'C'.

S&F, in repair, chromium plated, toilet paper holder complete all as specified and directed as per Cat Part No. CAN-1153N of jaquar or equivalent make as approved by GE from the makes specified in Appx 'C'.

S&F, in repair, chromium plated, towel rail 600mm long complete all as specified and directed as per Cat No. ACN-1111 of ESSCO or equivalent make as approved by GE.

S&F, in repair, 15mm brass chromium plated bib cock with wall flange, complete all as specified and directed as per Cat No. MQT-511 of ESSCO or equivalent make as approved by GE.

S&F, in repairs, stop valve angular, chromium plated for iron pipe or for unions and fixed to 15mm bore pipe, complete all as specified and directed as per Cat Part No. MQT-513A of ESSCO or equivalent make as approved by GE.

S&F, in repair, concealed stop cock heavy body casted cap 15mm chromium plated for iron pipe or for union and fixed to 15mm bore pipe, complete all as specified and directed as per Cat No. MQT-514A of ESSCO or equivalent make as approved by GE.

S&F, in repair, 8mm dia, brass chromium plated health faucet (hand shower) with 01 m long flexible tube and wall hook complete all as specified and directed as per Cat Part ALD-573 of Jaquar or equivalent make as approved by GE.

Taking up or down steel tubing and connections for 15mm bores of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bores of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bores of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bores of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bores of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bores of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) complete all as specified and directed for 25mm bores of pipe.

S&F, 40mm bore, low density polyethelene pipe (HDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

S&F, 40mm bore, high density poly ethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specifeid and directed.

Supply, hoisting, fixing in position and connecting, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed. Note- The water tank etc shall be contractor's supply.

Supply, hoisting, fixing in position and connecting, in repairs, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed. Note- The water tank etc shall be contractor's supply.

Supply, hoisting, fixing in position and connecting, in repairs, 1000 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed. Note- The water tank etc shall be contractor's supply.

S&F, bib taps, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

Supply only pillar taps cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F, stop valves, fancy type, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed.

S&F, 20mm bore dia of gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F, 25mm bore dia of gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

S&F, in repair, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight -210 Gms)

S&F, in repair, 25mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight -210 Gms)

S&F, towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all asa specified and directed.

S&F, PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F, PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

PVC (SWR)single T equal or unequal 75 mm bore with access door complete all as specified and directed.

S&F, 110 mm PVC (SWR) vent cowl complete all as specified and directed.

S&F, 75 mm outer dia PVC (SWR) floor trap, plain with Grating including joining with solvent complete all as specified and directed.

S&F, PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

M&L for cement concrete (1:3:6), type C-2, using 40mm graded stone aggregate in bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 200mm bore of pipe complete all as specified and directed.

M&L for 200mm bore reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed.

Cutting into existing manholes for connecting new drain pipes, making good to pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4, type B-1, smooth finished and reforming benching as required for 200mm bore of pipe complete all as specified and directed.

S&F, coloured vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F, in repairs, vitreous china wash down water closet pan (pedestal pattern) or white (excluding flushing cistern and flush pipe) but including trap, connection to drain pipe or outgoing pipe and to flushing pipe, antisyphonage pipe, seat and cover etc complete all as specified and directed .

S&F, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repair, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repair, kitchen sink with out drainage board made of stainless steel 1mm thick including supply and fix 32mm CP waste coupling, plug, washer, 32 mm bore and 60cm long PVC waste pipe including cantilever brackets made of mild steel angle iron 30x30x4mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning in ends of brackets to errecting stand into wall and making good disturbed portion in cement mortar 1:2 or in PCC 1:2:4, type B-1 using 20mm graded stone aggregate and connecting union to pipe, over all bowl size 600mm x 600mm x 230mm to 260mm complete all as specified and directed.

S&F in repair, vitreous china bowl urinal flat back, of size 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing flush pipe grating and union for discharge pipe. (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F, Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F, in repair, vitreous china wash basin, white, flat back of size 550mm x 400mm including brackets 32mm bore brass CP waste coupling Inlet/outlet, PVC flexible pipe, 600mm size of 15mm bore pipe with brass nut and washers etc grouted in cement mortar 1:2 in wall complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

S&F, Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F, soap dish, vitreous China white, ap proximate size 160x 160x90mm

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Dismantling timber in fillets rails, posts, rafters, purlins etc over 40 Sqcm in section in framed work complete all as specified and directed.

Dismantling timber in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in unframed work complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling of cast iron , SGSW, PVC or reinforced concrete drain pipes of size 100mm jointed in neat cement mortar and taking out of trenches if required complete all as specified and directed.

Taking down carefully unserviceable copper/aluminium point wiring (Light, fan, socket or power) complete including unserviceable fittings and fixtures such as switches, ceiling roses, pendents, regulators, sockets, lamp holders, brackets, except ceiling fittings, bulk head fittings, tube light fittings etc. and making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed.

S&F, ceiling rose, 3 terminal , any shade, of PVC/Polycarbonate, isolated body complete all as specified and directed

S&F, sub-main wiring with 2 single core, 1.5 Sqmm PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper multi stranded conductor drawn in and including PVC casing and caping with drawing one run copper conductor multi stranded, 1.5 Sqmm size as continuous earth wire drawn through complete all as specified and directed.

Taking down carefully and refixing existing light fittings complete, and making good disturbed surfaces of walls, floors etc. complete all as specified and directed.

Taking down carefully and refixing existing ceiling fans complete, with connected accessories complete all as specified and directed.

Taking down carefully and refixing existing lamp holder/Angle holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Taking down old/unsv existing tube light fittings/security light etc. for taking credit connected items complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing LED building security light fitting 25 Watt 230 V AC outdoor type complete all as specified and directed.

Supply and fixing LED street ligtht fitting 45 Watt 230 V AC outdoor type complete all as specified and as directed.

Supply and fixing magnum grand neo 40 watt LED light for surface mounting and suspended throught 2 nos, SS clamps & screws, corrosion resistatn, impact proof, IP-66 luminaire with PC housing & opal finish cover suitable for wet location, electronic driver and made up of scratch resistant unbreakable polycarbonate icluding cable gland with power coated CRCA sheet as reflector cover complete all as specified and as directed by Engineer-in-Charge as per Cat Part No. MAGNUMGRANDNEOIP6640WLED840SPC of make Havells of equivalent make as approved by GE.

Supply and fixing LED street ligtht fitting 70 watt 230 V AC outdoor type including GI Bracket of suitable size and length, nut and bolts with all connected items complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing BLDC type ceiling fans, 230 V, 1200 mm sweep, BEE, 5 star rated complete with blades, down rods, and connecting accessories, complete all as specified and directed by Engineer-in-Charge.

S&F, Refrigerator, electri driven (single phase), capacity 300 Litres, double door, frost free, star rated suitable for operation on 230 volt AC supply including connecting and testing complete all as specified and directed.

S&F, Water cooler having gross capacity of 120 Ltrs and nominal cooling of 60 ltrs per/hr. suitable for operation on single phase electric driven, 230 volts AC 50 Hz duly connecting and testing complete all as specified and directed.

Supply of steel body evaporative desert cooler with fan motor (ISI marked to IS 996 latest), fan blade of 450mm sweep of aluminum material for 4000 cum/hr nominal air capacity, wood wool filter pads of thickness size is 15mm or above with non-corrosive wire guard for filter pads, float valve at the inlet, submersible pump generally conforming to IS 11951 latest, the material of filter panel, grill, top of the cooler body is made of galvanized steel sheet ( ISI Marked to IS 277 latest) of thickness not less than 0.8mm and sump/water tank of 80 liters capacity including sheet thickness not less than 1.00mm with zinc coating not less than 100 gms/sq.meter and all internal surface of steel body painted with water-resistant paint to IS 9862 latest and brass/ss material drain 3 pin molded plug top of 5/6 amps plug with a 2.5-meter length of ISI marked connecting cable with, commissioning complete all as specified and directed.

Haritwal traders

BHAVIK SUPPLY CORPORATION

Shreeganesh Construction

Shree Builders

ALBA AC AND REF SERVICES

Ramdev and Sons

Singh Engineer And Contractor