Construction of Govt. College at Raipur Rani in Panchkula Distt. (Pdg. Street Light Only).

Amount

1 ( c ) Moulded case Circuit breakers. (31.12)

1.1 15 Amp..to 60 Amp.. 415 V ,10 KA 3-phase. (31.12 c (i))

2 (L) Miniature Circuit Breaker and Isolator. (31.17)

Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections. ()

Miniature circuit breakers of 9 KA breaking capacity. ((a) )

2.1 TPN MCB of 9 KA breaking capacity 40 Amp.. to 63 Amp.. (31.17(a) (iii))

3 (Q) Earthing (31.22)

3.1 Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. (31.22(iii))

3.2 Extra for using salt and charcoal / coke for pipe earth electrode as required. (31.22(ii))

3.3 Pdg. and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode as required . (31.22(xi))

3.4 Pdg. and fixing 25 mm x 5 mm G.I. Strip on surface or in recess for connections etc. as required with all labour and material. (31.22(xv))

4 Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections . (31.26)

4.1 25 Sq. mm 4 Core Armoured Cable. (31.26 (xIi) )

5 (v) Pedestal . (31.33)

Supply and erection of Godrej Almirah type M.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S.sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- ()

5.1 M.S.pedestal of size 750 mm wide , 1200 mm high ,300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster , having a base of size 1050 mm x 600 mm x 250 mm below ground level . (31.33 (iii) )

6 Supply and erection of double door sheet steel enclosures distribution boards suitable for MCBs and ELCBs etc. recessed in wall including bonding to earth with all labour and material requared complete the job in all respect upto the entire satisfaction of the Engineer-in Charge of the work. (31.41)

6.1 4-way, TP & N (Horizontal) (8+12) (31.41 (iv))

7 S/E of mark double walled corrugated (DWC) HDPE pipe laid 1 Mtr. Below ground level including digging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer in charge of work. (31.67)

7.1 HDPE 63/50 mm outer dia / inner dia (( i ))

8 HIGH MAST POLE (31.83)

8.1 Supply, installation, Testing and commissioning of 16 Mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 9/12 Nos. Luminaire loading fully motorized (power tool) with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including coast of set of foundation nut and bolts, installation at site complete in all respect upto entire satisfaction of Engineer-in-Charge. Thickness of Top Section = 3mm (Minimum) Bottom Section =4mm (Minimum) Top Dia = 150mm Bottom Dia = 410mm Thickness of Galvanization = Top = 65micron (Min.) Bottom = 85micron (Min.) (31.83 (ii))

9 S/E/T/C of LED Flood light Make:Bajaj Model No. Amaze BJFL 200W LED I with die cast aluminium body & clear toughned glass diffuser i/c cost of all labour & material required to complete the job in all respect upto the entire satisfaction of Engineer- in Charge of work. (Make: Philips / Crompton ) (NS-1)

10 S/E of Enclosure for 63 Amp. MCCB with all labour & required material the job in all respect upto the entire satisfaction fo Engineer- in Charge of work. Make-Havell's (NS-2)

M/S Mohan Lal Gupta

M/S NATWADIA ELECTRICAL COMPANY