MISC REPAIR TO COMPOUND WALL SECURITY WALL AND DRAINS UNDER AGE BR II MAINT AT INA EZHIMALA

Amount

Demolition of brick work, PCC block or stone masonry built in cement mortar complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving n.exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate ) as in surface channel and any drain complete all as specified and as directed.

M&L for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in gola junction of wall and floor or for settings floor trap/ ‘P’ trap in position and PCC padding in floor complete (work in foul condition as in shaft) all as specified and as directed.

M&L for cement concrete 1:2:4, type B1 (20mm graded stone aggregate) ditto, in lintels upto 1.5m clearspan, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

Demolition of RCC n.exc 15cm thickness complete all as specified and as directed.

M&L for pre cast RCC 1:2:4 type B1( using 20mm graded stone aggregate) as in cover slabs including casting of necessary form work set in cement mortar 1:4 complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks, type B1, 1:2:4 using 20 mm graded aggregate exc. 10 cm in width and setting in mortar 1:6 complete all as specified and as directed.

M&L for laterite stone walling of rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

Taking down cement or cement lime plaster on brick or concrete surfaces including raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed.

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished fair and even complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar 1:6 on stone masonry surfaces finished even and smooth with out extra cement complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and as directed.

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, 'Y' section for barbed wire, framework of water tanks and similiar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F in repairs galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. (each line wire to be measured) complete all as specified and as directed.

M&L for complete removal of existing treatment by using water jet washer and applying and applying two coats of exterior emulsion paint over a coat of exterior primer with using mechanical sprayer to paint complete all as specified and as per manufacturers instructions and as directed.

M&L for preparation of old/new painted surfaces by using water jet washer and applying and applying two coats of exterior emulsion paint over a coat of exterior primer with using mechanical sprayer to paint complete all as specified and as per manufacturers instructions and as directed.

M&L for preparation of old/new painted steel/iron surfaces exc 10cm width or girth using sand paper, grinding machine, scrapers etc and applying two coats of anti corrossive synthetic enamel paint over acoat of anticorrosive primer complete all as specified and as directed.

M/s K V Ramachandran

KDR CONSTRUCTION

PADMANABHAN. K.V

Benchmark Engineers and Contractors

LAKSHMI BUILDERS

RS ENTERPRISES

SATHEESAN.T.K

Sreekrupa Enterprises