GENERAL District Court Kozhikode USR Renovation work in additional sub courts and

Amount

Repair work

OD3025/2021-2022:Chipping and removing spalling/defective concrete and exposing the defective/ corroded reinforcement, joint the additional bar wherever 1/3 diameter of the bar is corroded. Removal of the defective concrete across the bar should be at least 2 mm beyond the defective bar so that the reinforcing bar can be cleaned with emery ribbon,wire brush etc.After cleaning the bar wash the bar with clean water and collect all the spalled/fallen concrete. Applying corrosion inhabitant, one coat of nitro zinc primer to make an unbroken continuous film on the bars and after cleaning the bar applying one coat of bonding agent Nitobond A R/SBR. Measurement is calculated for whole exposed area. Rate includes cost and conveyance of materials and labour etc complete.

OD3026/2021-2022:Providing and applying two component high build polymer modified cementitious reinstatement mortar Rendroc HB2 preferable with hand using wet on wet method to make sure that high strength polymer mix covers the corrosion inhabitant (nitrozinc primer and nitobond A) applied reinforcing bar on all sides and cover the acidic concrete. All including cost and conveyance of materials and labour charge etc complete

OD3027/2021-2022:Plastering the chemical treated surfaces in spalled/defective RCC structure with Polymer modified mortar to an average thickness of 10 mm Including cutting the patch in proper shape, raking out joints and preparing and plastering the surface complete and disposal of rubbish to the dumping ground, all complete as per direction of Engineering-Charge

14.1.1:Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 meters lead:With cement mortar 1:4 ( 1 cement : fine sand)

15.12.1:Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

50.9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

50.9.3.1:Providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows, 30 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction 0f Engineer in- charge. using Anjili/ Jack wood

50.9.4.1:Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood

50.9.6.1:Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Using Anjili wood / jack wood 30 mm thick shutters

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.2:Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.2:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

9.113:Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in- charge.

10.25.2:Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

OD3459/2021-2022:Providing and fixing hard drawnGI wire fabric mesh 25x25 mm or nearest size to openings including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.

50.14.1.1:Removing and refixing door shutters after necessary repairs for easy opening and closing etc complete as per the direction of site Engineer-in-charge.

50.14.1.2:Removing and refixing window shutters after necessary repairs for easy opening and closing etc complete as per the direction of site Engineer-in-charge

OD3275/2021-2022:Providing and fixing ISI marked Stainless steel tower bolt, (Barrel type) with necessary screws etc. complete: 100x10 mm

OD3276/2021-2022:Providing and fixing ISI marked Stainless steel tower bolt, (Barrel type) with necessary screws etc. complete: 150x10 mm

OD3277/2021-2022:Providing and fixing Stainless steel IS: 12817 marked pressed butt hinges bright finished with necessary screws etc, complete: 75x50x2.5 mm

OD3278/2021-2022:Providing and fixing Stainless steel IS: 12817 marked pressed butt hinges bright finished with necessary screws etc, complete: 125x64x2.5 mm

50.9.15.5:Providing and fixing iron hooks and eyes: 100 mm

OD3381/2021-2022:Supplying and fixing 300 mm stainless steel aldrop

14.43:Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

14.53.1:Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work

14.54.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to an give even shade:One or more coats on old work

14.70:Melamine polishing on wood work ( one or more coat)

OD3396/2021-2022:Supplying, stitching and fixing best quality clothe curtain for doors and window openings hoisted with 25mmStainless steel rods, brackets (304 grade), rings, end balls including cost and conveyance of all material and labour complete

OD3377/2021-2022:Supplying, laying and gluing best quality clothe type floor carpet in platforms including cost and conveyance of all material and labour complete

OD4551/2021-2022:Engaging Plumbing labour for miscellaneous works.

OD5158/2021-2022:Engaging labour for dismantling and re fixing of steel works and other repair works in grills, gates, and handrails, etc.

OD3379/2021-2022:Engaging labour for roof cleaning, material stacking and other miscellaneous works.

OD3380/2021-2022:Carriage and disposal of building rubbish and other waste materials upto 5.0 km lead by Mechanical Transport including loading, Unloading, payment for each load (aprox. 3.5cum/Load)

MADHUKARAN V

Bidder Name

SAJI P

MADHUKARAN V