Construction of ICAI Bhawan- Gorakhpur situated at plot no-B-11, Taramandal, near circuit house, opp- Ramgarhtal lake, Gorakhpur (U.P.)

S.No. DESCRIPTION DSR AMOUNT in Rs

(A) CIVIL, INTERIOR AND EXTERNAL DEVELOPMENT

1 EARTH WORK 7,56,804.78 -

2 CONCRETE WORK 6,99,565.06 -

3 REINFORCED CEMENT CONCRETE 2,43,23,124.65 -

4 BRICK WORK 27,88,745.58 -

6 WOOD, UPVC AND FRP WORK 36,71,557.15 2,68,968.00

7 STEEL WORK 7,36,960.79 -

9 FINISHING WORK 26,08,638.29 -

10 FALSE CEILING WORK 8,53,864.41 20,32,129.10

11 ALUMINIUM WORK 9,37,257.50 -

12 WATER PROOFING WORK 6,99,559.89 -

13 SIGNANGE WORKS - 4,03,800.00

14 ENTRANCE GATE 7,64,474.19 -

17 GUARD ROOM 7,48,850.43 -

18 FURNITURE WORK - 63,07,320.98

20 SW DRAIN WORKS 21,87,696.00 -

21 INTERNAL PLUMBING 11,93,158.17 10,11,263.53

22 EXTERNAL SEWER & DEVELOPMENT 4,68,334.38 18,66,715.00

Total with correction factor 0.973 as per OM CPWD dated

Signature of Tenderer 1 Signature of NBCC

1 ELECTRICAL WORKS 47,41,489.30 4,27,531.88

2 CCTV & SURVEILLIANCE SYSTEM 9,21,839.00

6 EPBAX & NETWORKING - 16,08,561.17

7 EXTERNAL ELECTRICAL WORK 44,31,536.00 35,16,111.51

9 AUDIO-VISUAL WORK 23,79,400.00

TOTAL AMOUNT(CIVIL+ E&M) 7,35,48,511.10 2,18,38,727.25

TOTAL AMOUNT(CIVIL+ E&M) 7,35,48,511.10 2,18,38,727.25

GRAND TOTAL 9,53,87,238.35

GRAND TOTAL 9,53,87,238.35

GRAND TOTAL IN LAC 953.87

GRAND TOTAL IN LAC 953.87

Signature of Tenderer 2 Signature of NBCC

Bill of Quantities Based on DSR-2023 with Cost Index & Market Rate

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11, TARAMANDAL, NEAR CIRCUIT HOUSE, OPP. RAMGARHTAL LAKE,

GORAKHPUR (U.P.)

Name of Work- Civil Work

BILL OF QUANTITIES

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

SH-2.0 EARTH WORK

1 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over

areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting

out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-

incharge. All kinds of soil 1172.07 cum 177.50 208042.43 0.00

2 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc.

in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and

watering, lead up to 50 and for all lift. 1047.21 cum 196.00 205253.16 0.00

3 1.1.2 Earthwork is disposal upto 5km By Mechanlcal Transport lncludlng loadlng,unloadlng and

4 2.22.3 Open timbering over areas including strutting, shoring etc. complete. (Measurements to be

taken of the face area timbered): Depth exceeding 3 m but not exceeding 4.5 m 185.85 sqm 71.30 13251.11 0.00

5 2.27 Supplying and filling in plinth with sand under floors, including watering, ramming,

consolidating and dressing complete. 56.08 cum 2123.75 119099.90 0.00

6 2.34 Supplying chemical emulsion in sealed containers including delivery as specified

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 214.90 litre 234.75 50447.78 0.00

7 2.35 Diluting and injecting chemical emulsion for Pre-CONSTRUCTIONAL anti-termite

treatment (excluding the cost of chemical emulsion) :

2.35.3 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm

apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement

: 2 Coarse sand) to match the existing floor :

8 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 386.78 sqm 310.05 119921.14 0.00

Sub-Total 756804.78 0.00

SH-4.0 CONCRETE WORK

9 4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of

centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-

III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from

natural sources) 83.520 cum 6812.00 568938.24 0.00

Signature of Tenderer

3 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

10 4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone

- III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast

40 mm nominal size, well rammed and consolidated and grouted with fine sand, including

necessary excavation, levelling & dressing & finishing the top smooth.

11 4.13 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved

quality using 1.7kg per square metre on damp proof course after cleaning the surface with

brushes and finally with apiece of cloth lightly soaked in kerosene oil.

12 4.2.3 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness)

including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string

lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,

sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and

1 :2:4 (1 Cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from natural sources 7.630 cum 9895.20 75500.38 0.00

13 4.10 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2

coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 40.56 sqm 410.85 16664.08 0.00

Sub-Total 699565.06 0.00

SH-5.0 REINFORCED CEMENT CONCRETE

14 5.33 Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing

reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimumspecified cement content in design mix shall be

payable separately. In case the cement content in design mix is more than 1.10 times of the

specified minimumcement content, the contractor shall have discretion to either re-design the

mix or bear the cost of extra cement.

5.33.1 All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg

Signature of Tenderer

4 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

15 5.33 Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing

reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimumspecified cement content in design mix shall be

payable separately. In case the cement content in design mix is more than 1.10 times of the

specified minimumcement content, the contractor shall have discretion to either re-design the

mix or bear the cost of extra cement.

5.33.2 All works above plinth level upto floor V level Concrete of M25 grade with minimum

cement content of 330 kg /cum 546.57 cum 9860.40 5389398.83 0.00

16 5.9 Centering and shuttering including strutting, propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. for mass concre 53.10 sqm 392.15 20823.17 0.00

5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 Suspended floors, roofs, landings, balconies and access platform 1498.66 sqm 927.25 1389632.49 0.00

5.9.4 Shelves (Cast in situ) 50.00 sqm 927.25 46362.50 0.00

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantileve 1331.53 sqm 736.40 980538.69 0.00

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Strut 732.96 sqm 961.30 704594.45 0.00

5.9.16.1 Edges of slabs and breaks in floors and walls Under 20 cm wid 322.00 metre 208.55 67153.10 0.00

5.9.19 Weather shade, Chajjas, corbels etc., including edge 50.00 sqm 951.10 47555.00 0.00

17 5.22.A.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in

position and binding all complete upto plinth level & above plinth level. Thermo-Mechanically

Treated bars of grade Fe-500D or more.

18 5.30 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projection 1858.58 metre 78.40 145712.67 0.00

Signature of Tenderer

5 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

SH-6.0 BRICK WORK

19 6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

20 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar

1:6 (1 cement : 6 coarse sand)

21 6.13.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar

1:4 (1 cement : 4 coarse sand)

22 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of

half brick masonry. 547.12 sqm 104.80 57338.18 0.00

SH-8.0 CLADDING WORK

23 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness t

be specified by the manufacturer), of approved make, in all colours, shades except burgundy,

bottle green, black of any size as approved by Engineer-in-Charge,in skirting, risers of steps

and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing

with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with

pigment of matching shade complete.

Signature of Tenderer

6 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

24 8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of

required size, approved shade, colour and texture laid over 20 mm thick base cement mortar

1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matchingpigment,

epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss

finish etc. complete at all levels.

25 MR Providing and fixing factory-manufactured decorative PVC fluted (baffle) wall panelling of

approved make, colour, texture, profile and pattern, comprising premium quality rigid PVC

fluted panels of approved dimensions, fixed on walls using approved high-strength polymer

adhesive and mechanical fasteners wherever required, complete in all respects as per approved

drawings and directions of the Engineer-in-Charge.

SH-9.0 WOOD, UPVC, FRP WORK, FIRE DOOR WORKS

26 9.147.A Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead

free uPVC multi-chambered frame, sach and mullion/coupler (where ever required) extruded

profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 m

foe series R3 and R4 profiles conforming to EN : 12608 in any shape, colour and design duly

reinforced with galvanized mild steel section made of required shape & size as per CPWD

Specification, uPVC extruded glazing beads, interlocks and inline sash adaptor (where ever

required) of appropriate dimension, EPDm gasket , hardware, SS 304 grade fasteners of

minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade

sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic

caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required)

shall be mitred cut and fusion welded/mechanicallyjointed duly sealed at all corners, including

drilling of holes for fixing haedware and drainage of water etc.

After Fixing frame the gap between frame and adjacent finished wall shall be filled with

weather proof sillicon sealant over backer rod of approved size and quality, all complete as per

approved drawing conforming to CPWD specification & direction of Engineer-in-charge.

Section of steel reinforcement and cross sections of uPVC Profiles to be as per design

approved by Engineer-inCharge. Wire mesh/Glazing of plain/toughened/ laminated

/double glass unit with / without high performance coatings as per design requirements and

conforming to IS :3548 & IS : 16231 shall be paid separately. Notes:- Structural

design proof cheacked from a Government Engineering Institute, to be provided by the

manufacturer for : (i) Sites with basic wind

speed >45 m/Sec as per IS 875 - Part 3. (ii) Sites with structure height more than 20m for all

9.147.B4.1 Three track panels sliding door with Aluminiumchannel for roller track, wool pile, zinc alloy

(zamak) powder coated handle on two panels along with multi-point locking system,adjustable

nylon rollers with SS 304 body. Using R3 series with frame (98 mm & above)x (40 mm &

above) & sach (30 mm & above ) x (74 mm & above).(Height upto 2.5 metre).

Signature of Tenderer

7 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

27 9.1.1 Providing wood work in frames of doors, windows, clerestory windows and other frames,

wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia

& length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

28 9..53 Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm

diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150

mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

29 9.21.1 Providing and fixing ISi marked flush door shutters conforming to IS 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood and well

matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on

both faces of shutters: 35 mm thick including ISi marked Stainless Steel butt hinges with

necessary screws 118.44 SQM 2392.65 283385.47 0.00

30 9.127.2 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss /

matt/ suede finish with high density protective surface layer and reverse side of adhesive

bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved

31 9.23. Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all

edges of flush door shutters (over all area of door shutter to be measured).

32 9.9.1.1 Providing and fixing glazed shutters for doors, windows and clerestor windows using 4 mm

thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of

required size with necessary screws. 14.85 SQM 4940.20 73361.97 0.00

33 9.96.1 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not

less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with

nuts and screws etc. complete : 300x16 mm

34 9.97 Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic0 coating not less

than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with

necessary screws etc. complete :

35 9.100.1 Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than

grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary

screws etc. complete : :125 mm.

36 9.101.2 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic

coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and

shade, with necessary screws etc. complete. Twin rubber stopper

Signature of Tenderer

8 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

37 9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door

closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg

to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with

necessary accessories and screws etc. complete.

38 9.161 Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating

confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory

approved by Engineer-in-charge,with suitable mounting on door frame, consisting of vertical

styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out

of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool

insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing

hinges of size 100x89x3mm of approved make, including applying a coat of approved fire

resistant primer or powder coating not less than 30 micron etc all complete as per direction of

Engineer-in-charge (panelling to be paid for seperately

39 9.162 Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating

confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory

approved by Engineer-in-charge,with suitable mounting on door frame, consisting of vertical

styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out

of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool

insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing

hinges of size 100x89x3mm of approved make, including applying a coat of approved fire

resistant primer or powder coating not less than 30 micron etc all complete as per direction of

Engineer-in-charge (panelling to be paid for seperately

40 9.164 Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc. with

G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size

20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150

mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less

than 30 micron on G.I. beading, & special ceramic tape kerafix 2000 of 5 x 20 mm size etc

complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of

Engineer-incharge with glass of required thickness having 120 minutes of fire resistance both

integrity & radiation control (EW120) and minimum20 minutesof insulation (EI20). The glass

should be manufacturedin India. The manufacturer have to give test report/certification of fire

glass and the glass should be toughned in nature with Bi Directional Fire Protection and have

the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL

accredited lab or by any other accreditation body which operates in accordance with ISO/IEC

17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be

eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42

41 9.139 Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch &

Lock on back side of the Panic Latch of reputed brand and manufactureto be approved by the

Engineer- in- charge, all complete

42 MR Door Closer TS 71 V Std Arm 01 Nos Per Leaf

Signature of Tenderer

9 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

43 MR SS ball bearing of size 100 x89x3mm

44 MR Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand

and manufacture,including providing and fixing top & bottom pivot & double acting hydraulic

floor spring type fixing arrangement and making necessary holes etc. for fixing required door

fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and

stopper etc.to be paid separately).

45 MR Door Handle

46 MR Door Lock

47 MR Providing, supplying, and fixing manually operated roller blinds of approved make and shade,

suitable for installation on windows, glazed partitions, curtain walls, and other openings,

complete in all respects. The roller blinds shall consist of premium quality, anti-static, dust-

resistant, UV-stabilized, fire-retardant (where specified), 100% polyester fabric with

acrylic/PVC coating or equivalent, having a minimum fabric weight of 300 GSM (or as per

approved manufacturer'sstandard), capable of blocking solar glare while permitting adequate

daylight. The fabric shall be colour-fast, wrinkle-resistant, mildew-resistant, and resistant to

fading under prolonged exposure to sunlight

SH-10.0 STEEL WORK

48 10.30.2 Providing & fixing glass panes with putty and glazing clips in steel doors,

windows, clerestory windows, all complete with : 5.5 mm thick glass panes

49 10.28 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates

etc., including welding, grinding, buffing, polishing and making curvature (wherever required)

and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing

with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required

size, on the top of the floor or the side of waist slab with suitable arrangement as per approval

of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be

considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

50 10.5.1 Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and

3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including

applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal

Signature of Tenderer

10 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

Sub-Total 736960.79 0.00

SH-11.0 FLOORING WORK

51 11.56.1 Providing and laying Polished Granite stone flooring in required design and patterns, in linear

as well as curvilinear portions of the building all complete as per the architectural drawings

with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement

: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry

admixed with pigment of matching shade including rubbing , curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab

of colour Black, Cheny/Ruby Red or equivalent 273.11 sqm 4481.30 1223887.84 0.00

52 11.20.3 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with

neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and

cleaning etc. complete, on 20 mm thick bed of cement mortar 1 :4 (1 cement: 4 coarse sand).

Dark shade pigment using ordinary cemen 313.26 sqm 1119.50 350694.57 0.00

53 MR Supply & Installation of laminated wooden flooring of suitable thikness 12mm AC5 of suitable

grade category product of approved made out of core high density -890-900kg/m3

fiberboard(HDF) & other component it treated for

abrasion,scratch,moistureprotection,flameprotection,U.Vresistant.edgetype, 0.5mm smallv-

groove, Backing under layer on min 2mm thikness AC5 shall provide as sound absorbent and

moisture protection layer the seamless impregenated decorative layer of specified

size.1215x197x8/12mmDesign,colour and pattern, all bonded together under high temperature

sand pressure with ecofriendly resin sspecified by the manufacturer, the material shall be

applicable warranty formaldended free, ecofriendly, highly recommended for high traffic area

and fully recyclable and matching shed and excluding quantity of skirting and profile.

54 12.55 Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI

(solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof

and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1 :4 (1

cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in

ratio of 1 :1, including rubbing and polishing of the surface upto 3 cuts complete, including

providing skirting upto 150 mm height along the parapet walls in the same manner.

55 11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to 15:15622, of

approved brand & manufacturer,in all colours and shade, laid on 20 mm thick cement mortar 1

:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting

the joints with white cement and matching pigments etc. The tiles must be cut with the zero

chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge,

clips of required thickness, leveling system and rubber mallet for placing the tiles gently and

11.41A.1.1 Double Charge Size of Tile 600 x 600mm 8.43 sqm 1453.65 12254.27 0.00

Signature of Tenderer

11 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

56 11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to 15:15622, of

approved brand & manufacturer,in all colours and shade, laid on 20 mm thick cement mortar 1

:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting

the joints with white cement and matching pigments etc. The tiles must be cut with the zero

chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge,

clips of required thickness, leveling system and rubber mallet for placing the tiles gently and

11.41A.1.3 Double Charge Size of Tile 600 x 1200 mm 639.38 sqm 1577.15 1008398.17 0.00

57 11.26.1 KOta stone slab flooring over 20 mm (average) thick base laid over and jointed with grey

cement slurry mixed with pigment to match the shade of the slab, including rubbing and

polishing complete with base of cement mortar 1 : 4 (1 cement: 4 coarse sand): 25mm Thick

58 11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm

(average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement

slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing

59 11.41A.3.1 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to 15:15622, of

approved brand & manufacturer,in all colours and shade, laid on 20 mm thick cement mortar 1

:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting

the joints with white cement and matching pigments etc. The tiles must be cut with the zero

chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge,

clips of required thickness, leveling system and rubber mallet for placing the tiles gently and

easily. Glazed Vitrified tiles Matt Size of Tile 600 x 600 mm 77.90 sqm 1464.85 114111.82 0.00

60 11.13.1 Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4

SH-13.0 FINISHING WORK

61 13.4.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand 1648.31 sqm 343.65 566441.73 0.00

62 13.15 20 mm cement plaster 1:2 (1 cement : 2 stone dust).

Signature of Tenderer

12 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

63 13.82.2 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content

less than 50 grams/ litre, of approved brand and manufacture, including applying additional

coats wherever required, to achieve even shade and colour. In two or more coats

64 13.47.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of

required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and

including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

65 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved

brand and manufacturer,over the plastered wall surface to prepare the surface even and smooth

66 13.48.3 Finishing with Deluxe Multi surface paint system for interiors and exteriors using

Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi

Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm

over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and

Signature of Tenderer

13 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

SH-12.0 FALSE CEILING WORK

67 12.52.1 Providing and fixing tiled false ceiling of specified materials of size

595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped

galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of

main 'T runner with suitably spaced joints to get required length and of size 24x38 mm made

from 0.30 mm thick (minimum)sheet, spaced at 1200 mm center to center and cross ꞏr of size

24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T"

at 600 mm center to center to fonn a grid of 1200x600 mm and secondary cross "T" of length

600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at

middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size

24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required

cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke

detectors etc. Main ~" runners to be suspended from ceiling using GI slotted cleats of size 27 x

37 x 25 x1 .6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI

adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200

mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be

pre-painted with polyester paint, all complete for all heights as per specifications, drawings

and as directed by Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge Global

white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of GI sheet

having galvanizing of 100 gms/sqm

(both sides inclusive) and electro statically polyester powder coated of thickness 60 microns

(minimum), including factory painted after bending.

Signature of Tenderer

14 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

68 MR Providing & Fixing of Fibre Glass Acoustical Suspended Ceiling System with 15 mm thick

Sierra OP Tegular 15/90 Edge Tiles with Knauf Silhouette 15mm face exposed grid.

The tiles shall have smooth laminated visual with Humidity Resistance (RH) of 95%, NRC

0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz

and 2000 Hz) as per ASTM C423 standard, CAC of 25db as per ASTM E1414, Light

Reflectance ≥86% as per ASTM E-1477, Thermal Conductivity λ = 0.040 W/mK, Colour

Global White, Fire Performance of class A2-s1, d0 according to EN 13501-1 with 15mm

Tegular 15/90˚ edge and 8mm drop in module size of 600 x 600mm. The scrim on the face of

the tile shall be cleanable and classified as ISO 14644-1 cleanroom class 5. It shall be suitable

for Green Building application, with Recycled content of 43% and VOC Emissions (French)

class of A+. The tile shall have Environmental Product Declaration as per ISO 14025 and EN

15804+A2. The tile shall have certifications from GRIHA and GreenPro thereby confirming

that it is an environment friendly product.

To ensure specification of tiles, ManufacturersTest Certificate is required having complete site

address & duly signed by Manufacturer.

SUSPENSION & INSTALLATION:- The tile shall be laid on KCS Silhouette 38 profile grid

system with 15mm white flanges incorporating a 6mm central reveal in white/black colour wit

mitred ends & “bird’s mouth” notches to provide mitred cruciform junctions colour global

white (Matching to tile color).Grid shall have double stroke rotary stitching on all T sections

i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all

sections). The end details of the cross tee shall be made of pre hardened steel clip fixed to the

ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee

to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a

pull out strength of more than 100kg. The T Sections shall be made of 90 gsm as per IS 277

(2003) pre-painted steel with baked polyester paint of 0T bending capability.

Perimeter trim to be Knauf wall angles of size 3000x19x19mm, secured to walls using screws

at 450mm centre to centre maximum. Installation should be carried out as per Knauf

recommended procedure using appropriate suspension system and designs as approved by the

Architect/ Engineer-in-Charge 247.19 sqm 2290.00 0.00 566065.10

69 12.53 Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium

silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level,

suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising@

120 grams per sqm including both side) consisting of main 'T runner suitably spaced at joints

to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet,

spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm

(Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a

grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24 x28 mm made

of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to

from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle

pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the

help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm

interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved

texture in the grid, including, cutting/ making opening for services like diffusers, grills, light

fittings, fixtures, smoke detectors etc., wherever required. Main 'T' runners to be suspended

from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5

mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level

clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main 'T. Bottom

exposed with 24 mm of all T-sections shall be pre-painted with polyster baked paint, for all

heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Signature of Tenderer

15 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

70 MR Providing and Fixing horizontal level suspended metal ceilings comprising of Metalworks V-P

500 Hook-on baffle systemwith Rectangular vertical baffle blades made of Aluminium(Grade

AA 3xxx, H14 temper) in coated thickness of 0.7mm ± 0.08mm as per IS:2676 (1981), post

coated to Wooden colour, suitable for architectural finishes and Interior applications, with

single grid systemand suitable spacing between baffles. The baffle width shall be 25mm, height

shall be 100mm, length shall be 3000mm. The on-center spacing of baffles shall be 125-150mm

(clear space between baffles 100-125mm respectively). The baffles shall have plain

unperforated finish with square edge, hook-on edges with suitable upturns. The baffles shall be

electrostatically powder coated using RoHS compliant pure polyester powder to achieve

coating thickness ranging from 60-80 microns. The powder coating shall pass Salt Spray Test

for 750 Hours as per ASTM B117, QUV –A Test for 1000hours as per ASTM G-154 – (Cycle

– 1) and Humidity test for 1000hours as per DIN 50017. The powder coating shall have an

adhesion of GT0 as per EN ISO 2409. The shade variation across batches shall be delta E<1

using Excite/BYK Gardner instrument and gloss level of 25±5% at 60˚ as per ASTM D523.

The grids shall comprise primary U-shaped slotted carrier bars of 120gsm galvanised steel (GI)

of 3000mm L x 43mm H x 30mm W x 1.5mm T. Accessories shall include baffle connector

(GI), baffle face cover (GI) – RAL shade, carrier bar splice (GI), carrier spring (SS), wall

SH-21.0 ALUMINIUM WORK

71 21.1.1.3 Providing and fixing aluminium work for doors, windows, ventilators and partitions with

extruded built up standard tubular sections/ appropriate Z sections and other sections of

approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia

and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with

required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free,

straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium

snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer in-charge. Polyester powder coated

aluminium (minimum thickness of polyester powder coating 50 micron)

72 21.10' Providing and fixing double glazed hermetically sealed glazing in

aluminium windows, ventilators and partition etc. with 6 mm thick clear

float glass both side, having 12 mm air gap, including providing EPDM

gasket, perforated aluminium spacers, desiccants, sealant (Both primary

and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge

Sub-Total 937257.50 0.00

SH-22.0 WATER PROOFING WORK

Signature of Tenderer

16 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

73 22.7.1 Providing and laying integral cement based water proofing treatment

including preparation of surface as required for treatment of roofs,

balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement

admixed with water proofing compound conforming to IS. 2645 and

approved by Engineer-in-charge over the RCC slab including adjoining

walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm

to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse

sand) admixed with water proofing compound conforming to IS : 2645

and approved by Engineer-in-charge over 20 mm thick layer of cement

mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-charge

to required slope and treating similarly the adjoining walls upto 300 mm

height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry

using 2.75 kg/ sqm of cement admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix

1:4 (1 cement :4 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge including

laying glass fibre cloth of approved quality in top layer of plaster and

finally finishing the surface with trowel with neat cement slurry and making

pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum

period of two weeks for curing and for final test. “All above operations to be

done in order and as directed and specified by the Engineer-in-Charge”:

22.7.1 With average thickness of 120 mm and minimum thickness

at khurra as 65 mm.

Signature of Tenderer

17 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

Signature of Tenderer

18 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

74 22.5 Providing and laying water proofing treatment in sunken portion of WCs,

bathroom etc., by applying cement slurry mixed with water proofing

cement compound consisting of applying.

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed

to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water

proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to

air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all

joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Sub-Total 699559.89 0.00

SH-23.0 SIGNAGE WORK

75 MR Providing, supplying, and fixing interior office room identification signages and directional

signages of approved size, design, colour, typography, and graphics as per approved signage

schedule and the directions of the Engineer-in-Charge, complete in all respects. The signages

shall be manufactured using minimum 3 mm thick acrylic sheet/ACP/aluminium composite

panel with laser-cut acrylic letters, UV-printed graphics, vinyl graphics, or equivalent

approved material, complete with matte or glossy finish as approved. The lettering, symbols,

arrows, room numbers, departmental names, accessibility symbols, pictograms, and other

graphics shall be produced using high-resolutionUV printing, laser engraving, or computer-cut

vinyl application with colour-fast inks resistant to fading, scratching, moisture, and normal

cleaning agents. Standard Office Room Name Plate (150 × 300 mm to 200 × 400 mm) 30.00 NOS 810.00 24300.00

76 MR Providing, fabricating, supplying, transporting, erecting, testing, commissioning and fixing

externally illuminated backlit building signage of approved design, shape and dimensions(16'-

0" × 4'-0" with approximately 3'-0" high letters or 20'-0" × 5'-0" with approximately 4'-0" high

letters, or as indicated in the drawings), comprising individually illuminated three-dimensional

letters, Institute logo/emblemand all associated components,complete in all respects as per the

approved drawings and directions of the Engineer-in-Charge. The item shall include

fabrication and installation of 3D illuminated channel letters and logo, ACP backing panel,

complete mild steel supporting framework, structural supports, mounting brackets, base plates,

anchor bolts, grouting, welding, cutting, drilling, alignment,levelling, anti-corrosive treatment,

primer and finish painting of all exposed steel members, complete LED illumination system

including LED modules, drivers/SMPS, timer, internal wiring, junction boxes, conduits,

weatherproof electrical accessories, cable management,electrical connections from the nearest

available power point, waterproof sealing at all fixing locations, testing, commissioningand

trial operation

Signature of Tenderer

19 Signature of NBCC

S.No DSR Item DESCRIPTION OF ITEM TOTAL DSR Amount in NON-DSR Amount in

. No. QTY UNIT Rs. Rs.

77 MR Providing, Carving, Supplying, Transporting and Fixing White Makrana Marble Statue of

Goddess Saraswati (Approx. 7 Quintals). Providing, hand-carving, supplying, transporting,

unloading, handling and fixing a 4'-0" (1200 mm) high statue of Goddess Saraswati carved

from Premium Grade-A Pure Makrana White Marble, free from cracks, veins, stains, cavities

and other visible defects. The statue shall be carved from a single or suitably jointed marble

block by skilled artisans with intricate detailing of facial features, ornaments, garments,Veena,

lotus pedestal and other traditional elements, maintaining perfect symmetry, proportion and

aesthetic appearance. The statue shall have an overall size of approximately 1200 mm height

(including base), 600 mm width and 550 mm depth, with an approximate finished weight of 7

quintals (700 kg). The exposed surfaces shall be machine and hand polished to achieve a

smooth, glossy, premium white finish while preserving all carved details.

78 MR Providing, fabricating and fixing a 300 mm high raised wooden stage over the finished floor

level for the Multipurpose Hall, comprising a rigid framework of MS square/rectangular

hollow sections of suitable sizes, duly welded, ground smooth, treated with one coat of zinc-

rich primer and two coats of synthetic enamel paint. The framework shall be adequately braced

and anchored to ensure rigidity, load-bearing capacity and vibration-free performance. The

stage top shall be formed with 19 mm thick BWP grade plywood fixed over treated timber/MS

joists as required, finished with approved 12 mm thick laminated wooden flooring having

matchingskirting, edge trims and nosing to exposed edges. The stage shall include all necessary

internal framing, stiffeners, anchor fasteners, levelling arrangements, cutting, finishing, edge

protection, concealed fixing accessories, and provisions required for a complete and durable

installation. The work shall also include providing access steps, making good all junctions,

polishing/finishing exposed members, cleaning, testing and handing over complete in all

respects as directed by the Engineer-in-Charge. Stage Height: 300 mm above finished floor

Sub-Total 0.00 403800.00

Say In Lacs. 422.87 38.26

Signature of Tenderer

20 Signature of NBCC

Bill Of Quantities Based On DSR-2023 With Cost Index & Market Rate

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11, TARAMANDAL, NEAR CIRCUIT

HOUSE, OPP. RAMGARHTAL LAKE, GORAKHPUR (U.P.)

Name of Work- Entrance Gate

DSR Amount NON-DSR

S.N. Ref. No. DESCRIPTION OF ITEM Qty Unit Rate In Rs.

in Rs. Amount in

SH-2.0 EARTH WORK

Earth work in excavation by mechanical means (Hydraulic

excavator)/ manual means over areas (exceeding 30 cm in

depth, 1.5 m in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth lead upto 50 m

and lift upto 1.5 m, as directed by Engineer-incharge. All

Sub-Total 6622.53 0.00

SH-4.0 CONCRETE WORK

Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All

work up to plinth level : 1:4:8 (1 Cement : 4

coarse sand (zone-III) derived from

natural sources : 8 graded stone aggregate 40 mm

nominal size derived from natural sources)

Sub-Total 13487.76 0.00

SH-5.0 REINFORCED CEMENT CONCRETE

Centering and shuttering including strutting, propping etc.

and removal of form for :

Foundations, footings, bases of columns, etc. for mass

concrete 20.74 sqm 392.15

Lintels, beams, plinth beams, girders, bressumers and

cantilevers 42.00 sqm 736.40

Signature of Tenderer 21 Signature of NBCC

DSR Amount NON-DSR

S.N. Ref. No. DESCRIPTION OF ITEM Qty Unit Rate In Rs.

in Rs. Amount in

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 36.40 sqm 961.30 34991.32 0.00

Suspended floors, roofs, landings, balconies and access

platform 10.50 sqm 927.25

Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived

from natural sources, Portland Pozzolana / Ordinary

Portland /Portland Slag cement, admixtures in recommended

proportions as per IS: 9103 to accelerate / retard setting of

concrete, to improve durability and workability without

impairing strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the cost of

centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for

the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified

cement content in design mix shall be payable separately. In

case the cement content in design mix is more than 1.10

times of the specified minimum cement content, the

contractor shall have discretion to either re-design the mix or

bear the cost of extra cement.

All works upto plinth level Concrete of M25 grade with

minimum cement content of 330 kg /cum

All works above plinth level upto floor V level Concrete

5 5.33.2.1 of M25 grade with minimum cement content of 330 kg /cum 6.26 CUM. 9,860.40 61726.10 0.00

Signature of Tenderer 22 Signature of NBCC

DSR Amount NON-DSR

S.N. Ref. No. DESCRIPTION OF ITEM Qty Unit Rate In Rs.

in Rs. Amount in

Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all complete

6 5.22.6 above plinth level Thermo-Mechanically Treated bars of 2133.00 Kg 107.85 230044.05 0.00

grade Fe-500D or more.

Sub-Total 424223.91 0.00

SH-10.0 STEEL WORK

Structural steel work in single section, fixed with or without

connecting plate,includingcutting, hoisting, fixing in position

and applying a priming coat of approved steel primer all

Sub-Total 268262.10 0.00

SH-13.0 FINISHING WORK

12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand)

Finishing walls with Premium Acrylic Smooth exterior paint

with Silicone additives of required shade: New work (Two

9 or more coats applied @ 1.43 ltr/10 sqm over and including 101.71 SQM. 171.10 17402.58 0.00

priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Signature of Tenderer 23 Signature of NBCC

DSR Amount NON-DSR

S.N. Ref. No. DESCRIPTION OF ITEM Qty Unit Rate In Rs.

in Rs. Amount in

Finishing with Deluxe Multi surface paint system for

interiors and exteriors using Primer as per manufacturers

specifications : Painting Steel work with Deluxe Multi

10 13.48.3 Surface Paint to give an even shade. Two or more coat 36.00 SQM. 170.70 6145.20 0.00

applied @ 0.90 ltr/10 sqm over an under coat of primer

applied @ 0.80 ltr/10 sqm of approved brand and

Sub-Total 58500.42 0.00

COST FOR TWO GATE Say In Lakh 7.64 0.00

Signature of Tenderer 24 Signature of NBCC

Bill Of Quantities Based On DSR-2023 With Cost Index & Market Rate

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11, TARAMANDAL, NEAR CIRCUIT HOUSE,

OPP. RAMGARHTAL LAKE, GORAKHPUR (U.P.)

Name of Work- Boundary Wall

BOUNDARY WALL FOR 30.28 MTR

S. No. 2023 DESCRIPTION

UNIT Rate In Rs.

DSR Amount DSR

Item QTY in Rs. Amount

SH-2.0 EARTH WORK

1 Earth work in excavation by mechanical means (Hydraulic

excavator)/ manual means over areas (exceeding30 cm in depth,

1.5 m in width as well as 10 sqm on plan) including getting out

2.6.1 and disposal of excavated earth lead upto 50 m and lift upto 1.5 143.32 Cum 177.50 25439.30 0.00

m, as directed by Engineer-incharge. All kinds of soil

Sub-Total 25439.30 0.00

SH-4.0 CONCRETE WORK

2 Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All work

4.1.8 up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) 13.60 Cum 6812.00 92643.20 0.00

derived fromnatural sources : 8 graded stone aggregate 40

mmnominal size derived from natural sources)

3 Providing & applying a coat of residual petroleum bitumen of

grade of VG-10 of approved quality using 1.7kg per square

4.13 metre on damp proof course after cleaning the surface with 24.21 sqm 146.15 3538.29 0.00

brushes and finally with apiece of cloth lightly soaked in

Signature of Tenderer 25 Signature of NBCC

2023 TOTAL DSR Amount DSR

S. No. DESCRIPTION UNIT Rate In Rs.

Item QTY in Rs. Amount

Sub-Total 96181.49 0.00

SH-5.0 REINFORCED CEMENT CONCRETE

4 Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommendedproportions

as per IS: 9103 to accelerate / retard setting of concrete, to

improve durability and workability without impairing strength;

including pumping of concrete to site of laying, curing, carriage

for all leads; but excluding the cost of centering, shuttering,

5.33 finishing and

reinforcement as per direction of the engineer-in-charge;for the

following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement

content in design mix shall be payable separately. In case the

cement content in design mix is more than 1.10 times of the

specified minimum cement content, the contractor shall have

discretion to either re-design the mix or bear the cost of extra

All works upto plinth level Concrete of M25 grade with

minimum cement content of 330 kg /cum

Signature of Tenderer 26 Signature of NBCC

2023 TOTAL DSR Amount DSR

S. No. DESCRIPTION UNIT Rate In Rs.

Item QTY in Rs. Amount

5 Providing and laying in position ready mixed or site batched

design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommendedproportions

as per IS: 9103 to accelerate / retard setting of concrete, to

improve durability and workability without impairing strength;

including pumping of concrete to site of laying, curing, carriage

5.33 for all leads; but excluding the cost of centering, shuttering,

finishing and reinforcement as per direction of the engineer-in-

charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement

content in design mix shall be payable separately. In case the

cement content in design mix is more than 1.10 times of the

specified minimum cement content, the contractor shall have

discretion to either re-design the mix or bear the cost of extra

All works above plinth level upto floor V level Concrete of

M25 grade with minimum cement content of 330 kg /cum

6 Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all complete

5.22.6 above plinth level Thermo-MechanicallyTreated bars of grade 5266.00 Kg 107.85 567938.10 0.00

Fe-500D or more.

7 Centering and shuttering including strutting, propping etc. and

5.9 removal of form for :

A Foundations, footings, bases of columns, etc. for mass concrete

Signature of Tenderer 27 Signature of NBCC

2023 TOTAL DSR Amount DSR

S. No. DESCRIPTION UNIT Rate In Rs.

Item QTY in Rs. Amount

B Lintels, beams, plinth beams, girders, bressumers and

C 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 150.14 Sqm 961.30 144329.58 0.00

SH-6.0 BRICK WORK

Brick work with common burunt clay F.B.S. (non modular)

bricks of class designation 7.5 in superstructure above plinth

8 6.4.2 level up to floor V level in all shapes and size in: Cement mortar 20.62 Cum 9105.95 187764.69 0.00

1:6 (1 cement: 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in superstructure above

9 6.13.1 plinth level up to floor V level. Cement mortar 1:3 (1 cement: 3 81.05 Sqm 1150.50 93248.03 0.00

Sub-Total 281012.72 0.00

SH-13.0 FINISHING WORK

10 13.4.2 12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand 338.57 Sqm 343.65 116349.58 0.00

11 15 mm cement plaster on rough side of single or half brick wall

12 Finishing walls with Premium Acylic Smooth exterior paint with

Silicone additives of required shade :

13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over 587.85 Sqm 171.10 100581.14 0.00

and priming coat of exterior primer applied @ 0.90 litre / 10

Signature of Tenderer 28 Signature of NBCC

2023 TOTAL DSR Amount DSR

S. No. DESCRIPTION UNIT Rate In Rs.

Item QTY in Rs. Amount

13 Providing and applying white cement based putty of average

13.80 thickness 1 mm, of approved brand and manufacturer, over the 587.85 Sqm 156.05 91733.99 0.00

plastered wall surface to prepare the surface even and smooth

15 Finishing with Deluxe Multi surface paint system for interiors

and exteriors using Primer as per manufacturers specifications :

Painting Steel work with Deluxe Multi Surface Paint to give an

13.48.3 even shade. Two or more coat applied @ 0.90 ltr/10 sqm over 47.37 Sqm 170.70 8086.06 0.00

an under coat of primer applied @ 0.80 ltr/10 sqm of approved

brand and manufacture

Sub-Total 415303.62 0.00

SH-10.0 STEEL WORK

14 Steel work welded in built up sections/ framed work, including

cutting, hoisting, fixing in position and applying a priming coat

10.25.2 of approved steel primer using structural steel etc. as required.In 568.44 Kg 156.05 88705.06 0.00

gratings, frames, guard bar, ladder, railings, brackets, gates and

Sub-Total 88705.06 0.00

Signature of Tenderer 29 Signature of NBCC

Bill of Quantities Based on DSR-2023 with Cost Index & Market Rate

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11, TARAMANDAL, NEAR CIRCUIT HOUSE, OPP.

RAMGARHTAL LAKE, GORAKHPUR (U.P.)

Name of Work- INTERLOCKING PATHWAY

BILL OF QUANTITY

S. No. DSR-2023 DESCRIPTION TOTAL QTY UNIT

DSR Amount in Rs. NON-DSR Amount in Rs.

SH-2.0 EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator)/

manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well

1 2.6.1 as 10 sqm on plan) including getting out and disposal of excavated earth 17.61 Cum 177.50 3125.78 0.00

lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Sub-Total 3125.78 0.00

SH-4.0 CONCRETE WORK

Providing and laying in position cement concrete of specified grade

4.1 excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8

2 4.1.8 graded stone aggregate 40 mm nominal size derived from natural sources) 4.07 Cum 6812.00 27724.84 0.00

Sub-Total 27724.84 0.00

SH-6.0 BRICK WORK

3 Brick work in foundation

6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class

(a) designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 192.53 Cum 7132.25 1373172.09 0.00

SH-13.0 FINISHING WORK

12 mm cement plaster : 1:4 (1 cement : 4 Coarse sand) mortar etc.

Sub-Total 35163.24 0.00

SH-16.0 ROAD WORK

Signature of Tenderer 30 Signature of NBCC

S. No. DSR-2023 DESCRIPTION TOTAL QTY UNIT

DSR Amount in Rs. NON-DSR Amount in Rs.

Providing and laying factory made chamfered edge Cement Concrete paver

blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of

required strength, thickness & size/ shape, made by table vibratory method

using PU mould, laid in required colour & pattern over 50mm thick

compacted bed of sand, compacting and proper embedding/laying of inter

5 locking paver blocks into the sand bedding layer through vibratory 429.09 Sqm 1045.65 448677.96 0.00

16.91 compaction by using plate vibrator, fillingthe joints with sand and cutting of

paver blocks as per required size and pattern, finishing and sweeping extra

sand. complete all as per direction of Engineer-in-Charge.

60 mm thick C.C. paver block of M-35 grade with approved color

design and pattern

Sub-Total 448677.96 0.00

Signature of Tenderer 31 Signature of NBCC

Bill of Quantities Based on DSR-2023 with Cost Index & Market Rate

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11, TARAMANDAL, NEAR CIRCUIT HOUSE, OPP.

RAMGARHTAL LAKE, GORAKHPUR (U.P.)

Name of Work- Civil Work- Guard Room

TOTAL Rate In DSR Amount in NON-DSR

S.No. DSR Item No. DESCRIPTION OF ITEM UNIT

QTY Rs. Rs. Amount in Rs.

SH-2.0 EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual

means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm

on plan) including getting out and disposal of excavated earth lead upto 50 m

and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil 39.97 cum 177.50 7094.68 0.00

Supplying and filling in plinth with sand under floors, including watering,

2 2.27 ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 10.35 litre 234.75 2429.66 0.00

Diluting and injecting chemical emulsion for Pre-CONSTRUCTIONAL anti-

4 2.35 termite treatment (excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre per

hole, 300 mm apart including drilling 12 mm diameter holes and plugging with

cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :

2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 18.62 sqm 310.05 5773.13 0.00

Sub-Total 18100.82 0.00

SH-4.0 CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding

the cost of centering and shuttering - All work up to plinth level :

5 4.1.8 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8

graded stone aggregate 40 mm nominal size derived from natural sources)

Signature of Tenderer 32 Signature of NBCC

TOTAL Rate In DSR Amount in NON-DSR

S.No. DSR Item No. DESCRIPTION OF ITEM UNIT

QTY Rs. Rs. Amount in Rs.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of

approved quality using 1.7kg per square metre on damp proof course after

cleaning the surface with brushes and finally with apiece of cloth lightly soaked

in kerosene oil. 5.45 sqm 146.15 796.52 0.00

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4

(1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3

coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over

75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and

8 4.17 consolidated and grouted with fine sand, including necessary excavation,

levelling & dressing & finishing the top smooth.

Sub-Total 55155.87 0.00

SH-5.0 REINFORCED CEMENT CONCRETE

Providing and laying in position ready mixed or site batched design mix cement

concrete for reinforced cement concrete work; using coarse aggregate and fine

aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103

to accelerate / retard setting of concrete, to improve durability and workability

without impairing strength; including pumping of concrete to site of laying,

9 5.33 curing, carriage for all leads; but excluding the cost of centering, shuttering,

reinforcement as per direction of the engineer-in-charge; for the following grades

Note: Extra cement up to 10% of the minimum specified cement content in

design mix shall be payable separately. In case the cement content in design mix

is more than 1.10 times of the specified minimum cement content, the contractor

h ll h di ti t ith d i th i b th t f t t

All works upto plinth level Concrete of M25 grade with minimum cement

Signature of Tenderer 33 Signature of NBCC

TOTAL Rate In DSR Amount in NON-DSR

S.No. DSR Item No. DESCRIPTION OF ITEM UNIT

QTY Rs. Rs. Amount in Rs.

Providing and laying in position ready mixed or site batched design mix cement

concrete for reinforced cement concrete work; using coarse aggregate and fine

aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103

to accelerate / retard setting of concrete, to improve durability and workability

without impairing strength; including pumping of concrete to site of laying,

curing, carriage for all leads; but excluding the cost of centering, shuttering,

10 5.33 finishing and

reinforcement as per direction of the engineer-in-charge; for the following grades

Note: Extra cement up to 10% of the minimum specified cement content in

design mix shall be payable separately. In case the cement content in design mix

is more than 1.10 times of the specified minimum cement content, the contractor

shall have discretion to either re-design the mix or bear the cost of extra cement.

All works above plinth level upto floor V level Concrete of M25 grade with

minimum cement content of 330 kg /cum 4.41 cum 9860.40 43484.36 0.00

Steel reinforcement for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete upto plinth level & above plinth

11 5.22.A.6 level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete 10.92 sqm 392.15 4282.28 0.00

5.9.3 Suspended floors, roofs, landings, balconies and access platform 13.21 sqm 927.25 12248.97 0.00

5.9.4 Shelves (Cast in situ) 1.82 sqm 927.25 1687.60 0.00

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers 33.51 sqm 736.40 24676.76 0.00

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 22.39 sqm 961.30 21523.51 0.00

5.9.16.1 Edges of slabs and breaks in floors and walls Under 20 cm wide 20.65 metre 208.55 4306.56 0.00

5.9.19 Weather shade, Chajjas, corbels etc., including edges 2.88 sqm 951.10 2739.17 0.00

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C.

13 5.30 projections.

Sub-Total 275559.77 0.00

SH-6.0 BRICK WORK

Signature of Tenderer 34 Signature of NBCC

TOTAL Rate In DSR Amount in NON-DSR

S.No. DSR Item No. DESCRIPTION OF ITEM UNIT

QTY Rs. Rs. Amount in Rs.

Brick work with common burnt clay F.P.S. (non modular) bricks of class

14 6.1.2 designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6

Brick work with common burnt clay F.P.S. (non modular) bricks of class

15 6.4.2 designation 7.5 in superstructure above plinth level up to floor V level in all

shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) 13.32 cum 9105.95 121291.25 0.00

Brick work with common burnt clay F.P.S. (non modular) bricks of class

16 6.13.2 designation 7.5 in superstructure above plinth level up to floor V level in all

shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) 9.29 sqm 1123.80 10440.10 0.00

Sub-Total 158334.64 0.00

SH-9.0 WOOD, UPVC AND FRP WORK

Providing and fixing ISi marked flush door shutters conforming to IS 2202

(Part I) non-decorative type, core of block board construction with frame of 1st

17 9.5.1.1 class hard wood and well matched commercial 3 ply veneering with vertical

grains or cross bands and face veneers on both faces of shutters: 35 mm thick

including ISi marked Stainless Steel butt hinges with necessary screws

35 mm thick including ISI marked Stainless Steel butt hinges with necessary

18 9.127.2 Providing & Fixing decorative high pressure laminated sheet of plain / wood

grain in gloss / matt/ suede finish with high density protective surface layer and

reverse side of adhesive bonding quality conforming to IS : 2046 Type S,

including cost of adhesive of approved quality.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum

depth on all edges of flush door shutters (over all area of door shutter to be

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic

coating not less than grade AC 10 as per IS : 1868), transparent or dyed to

20 9.96.1 required colour or shade, with nuts and screws etc. complete : 300x16 mm

Signature of Tenderer 35 Signature of NBCC

TOTAL Rate In DSR Amount in NON-DSR

S.No. DSR Item No. DESCRIPTION OF ITEM UNIT

QTY Rs. Rs. Amount in Rs.

Providing and fixing aluminium tower bolts, ISI marked, powder coated

(minimum thickness of powder coating 50 micron) transparent or dyed to

21 9.97 required colour or shade, with necessary screws etc. complete : 250x10 mm.

Providing and fixing aluminium handles, ISI marked, powder coated (minimum

thickness of powder coating 50 micron) transparent or dyed to required colour or

22 9.100.1 shade, with necessary screws etc. complete :125 mm.

Providing and fixing aluminium hanging floor door stopper, ISI marked,

anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent

23 9.101.2 or dyed to required colour and shade, with necessary screws etc. complete. Twin

Providing and fixing aluminium die cast body tubular type universal hydraulic

door closer (having brand logo with ISI, IS : 3564, embossed on the body, door

24 9.83 weight upto 35 kg and door width upto 700 mm), with necessary accessories and

screws etc. complete.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-

section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive

shutter of 30 mm thickness. The laminate shall be moulded with fire resistant

25 9.121 grade unsaturated polyester resin and chopped mat. Door frame laminate shall be

2mm thick and shall be filled with suitable wooden block in all the three legs.

The frame shall be covered with fiber glass from all sides. M.S. stay shall be

provided at the bottom to steady the frame 6.00 meter 570.95 3425.70 0.00

30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of

required colour and approved brand and manufacture, made with fire - retardant

grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for

26 9.122.1 forming hollow rails and styles, with wooden frame and suitable blocks of

seasoned wood inside at required places for fixing of fittings, cast monolithically

with 5 mm thick FRP laminate for panels conforming to IS: 14856, including

fixing to frames

Sub-Total 25416.76 0.00

Signature of Tenderer 36 Signature of NBCC

TOTAL Rate In DSR Amount in NON-DSR

S.No. DSR Item No. DESCRIPTION OF ITEM UNIT

QTY Rs. Rs. Amount in Rs.

SH-10.0 STEEL WORK

Providing and fixing M.S. Tubular frames and shutters for doors, windows,

ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm

thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of

27 10.15 required size, including fixing of necessary butt hinges and screws and applying

a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block

10.15.1 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate

20 mm nominal size)

Steel work welded in built up sections/ framed work, including cutting, hoisting,

28 10.25 fixing in position and applying a priming coat of approved steel primer using

structural steel etc. as required.

In grill, gratings, frames, guard bar, ladder, railings, brackets, gates and similar

Providing & fixing glass panes with putty and glazing clips in steel

29 10.30 doors,windows, clerestory windows, all complete with :

Sub-Total 22973.72 0.00

SH-13.0 FINISHING WORK

30 13.4.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) 56.72 sqm 343.65 19492.52 0.00

31 13.5 15 mm cement plaster on the rough side of single or half brick wall of mix :

Distempering with 1st quality acrylic distemper (ready mixed) having VOC

content less than 50 gram/litre, of approved manufacturer and of required shade

and colour all complete to achieve even shade and colour :

New work (two or more coats) over and including water

13.41.1 thinnable priming coat with cement primer having VOC content less than 50

Signature of Tenderer 37 Signature of NBCC

TOTAL Rate In DSR Amount in NON-DSR

S.No. DSR Item No. DESCRIPTION OF ITEM UNIT

QTY Rs. Rs. Amount in Rs.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone

additives of required shade: New work (Two or more coats applied @

1.43 ltr/10 sqm over and including priming coat of exterior primer applied @

Providing and applying white cement based putty of average thickness 1 mm, of

34 13.80 approved brand and manufacturer, over the plastered wall surface to prepare the

surface even and smooth Complete.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two

35 13.48.3 or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @

0.80 ltr/ 10 sqm of approved brand and manufacture 8.46 sqm 170.70 1444.12 0.00

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or

36 13.48.2 more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75

ltr/10 sqm of approved brand and manufacture

Sub-Total 104219.39 0.00

SH-16.0 ROAD WORK

Providing and laying factory made 80 mm thick rubber moulded Interlocking

cement concrete tiles (30mpa) including 25 mm thick compacted bed of fine sand

compacting and proper embedding/laying of Interlocking tiles leveling and

37 16.68 dressing of surface to required level and slope, filling joints with fine sand

including the cost of material, labour T&P etc. required for proper completion of

work as directed by Engineer-in-Charge.

Sub-Total 8748.00 0.00

SH-11.0 FLOORING WORK

Providing and laying vitrified floor tiles in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS: 15622, of approved make, in all colours and shades, laid on

38 11.41 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement

and matching pigments etc., complete.

Signature of Tenderer 38 Signature of NBCC

TOTAL Rate In DSR Amount in NON-DSR

S.No. DSR Item No. DESCRIPTION OF ITEM UNIT

QTY Rs. Rs. Amount in Rs.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by

manufacturer), with water absorption less than 0.08 % and conforming to I.S.

15622, of approved make, in all colours & shade, in skirting, riser of steps, over

39 11.46.2 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with

grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement

& matching pigments etc. complete. 0.99 sqm 1623.05 1606.82 0.00

11.41A.3.1 Providing and laying Vitrified tiles in floor in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and

conforming to 15:15622, of approved brand & manufacturer, in all colours and

shade, laid on 20 mm thick cement mortar 1 :4 (1 cement: 4 coarse sand) jointing

40 with grey cement slurry @3.3 kg/sqm including grouting the joints with white

cement and matching pigments etc. The tiles must be cut with the zero chipping

diamond cutter only. Laying of tiles will be done with the notch trowel, plier,

wedge, clips of required thickness, leveling system and rubber mallet for placing

the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size.

Size of Tile 600 x 600 mm

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40

41 11.13.1 mm wide and 4 mm thick

Sub-Total 28254.22 0.00

SH-8.0 CLADDING WORK

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:

15622 (thickness to be specified by the manufacturer), of approved make, in all

colours, shades except burgundy, bottle green, black of any size as approved by

42 8.31 Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed

of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement

slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment

of matching shade complete 18.48 sqm 1267.95 23431.72 0.00

Sub-Total 23431.72 0.00

SH-22.0 WATER PROOFING WORK

Signature of Tenderer 39 Signature of NBCC

TOTAL Rate In DSR Amount in NON-DSR

S.No. DSR Item No. DESCRIPTION OF ITEM UNIT

QTY Rs. Rs. Amount in Rs.

43 22.7.1 Providing and laying integral cement based water proofing treatment

including preparation of surface as required for treatment of roofs,

balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement

admixed with water proofing compound conforming to IS. 2645 and

approved by Engineer-in-charge over the RCC slab including adjoining

walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm

to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse

sand) admixed with water proofing compound conforming to IS : 2645

and approved by Engineer-in-charge over 20 mm thick layer of cement

mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-charge

to required slope and treating similarly the adjoining walls upto 300 mm

height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry

using 2.75 kg/ sqm of cement admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix

1:4 (1 cement :4 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge including

laying glass fibre cloth of approved quality in top layer of plaster and

finally finishing the surface with trowel with neat cement slurry and making

pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum

period of two weeks for curing and for final test. “All above operations to be

done in order and as directed and specified by the Engineer-in-Charge”:

22.7.1 With average thickness of 120 mm and minimum thickness

at khurra as 65 mm.

Signature of Tenderer 40 Signature of NBCC

TOTAL Rate In DSR Amount in NON-DSR

S.No. DSR Item No. DESCRIPTION OF ITEM UNIT

QTY Rs. Rs. Amount in Rs.

22.5 Providing and laying water proofing treatment in sunken portion of WCs,

bathroom etc., by applying cement slurry mixed with water proofing

cement compound consisting of applying.

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water

proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed

to air cure for 4 hours.

44 (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water

proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to

air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all

joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Sub-Total 28655.52 0.00

Signature of Tenderer 41 Signature of NBCC

Bill of Quantities Based on DSR-2023 with Cost Index & Market Rate

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11, TARAMANDAL, NEAR CIRCUIT HOUSE,

OPP. RAMGARHTAL LAKE, GORAKHPUR (U.P.)

Name of Work- UG TANK

Rate In DSR Amount

S. N. Item No. DESCRIPTION OF ITEM TOTAL QTY UNIT Amount in

SH-2.0 EARTH WORK

1 2.6.1 Earth work in excavation by mechanical means (Hydraulic

excavator)/ manual means over areas (exceeding 30 cm in depth,

1.5 m in width as well as 10 sqm on plan) including getting out

and disposal of excavated earth lead upto 50 m and lift upto 1.5

m as directed by Engineer incharge

Sub-Total 37901.58 0.00

SH-4.0 CONCRETE WORK

2 4.1.8 Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All work

up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III)

derived from natural sources : 8 graded stone aggregate 40 mm

nominal size derived from natural sources)

Sub-Total 29155.36 0.00

SH-5.0 REINFORCED CEMENT CONCRETE

Signature of Tenderer 42 Signature of NBCC

Rate In DSR Amount

S. N. Item No. DESCRIPTION OF ITEM TOTAL QTY UNIT Amount in

3 5.33 Providing and laying in position ready mixed M-25 grade

concrete for reinforced cement concrete work, using cement

content as per approved design mix, manufactured in fully

automatic batching plant and transported to site of work in

transit mixer for all leads, having continuous agitated mixer,

manufactured as per mix design of specified grade for reinforced

cement concrete work, including pumping of R.M.C. from transit

mixer to site of laying , excluding the cost of centering,

shuttering finishing and reinforcement, including cost of

admixtures in recommended proportions as per IS : 9103 to

accelerate/ retard setting of concrete, improve workability

without impairing strength and durability as per direction of the

Engineer-in-charge.

(Note :- Cement content considered in this item is @ 330 kg/

cum Excess/less cement used as per design mix is

5.33.1 All works upto plinth leve 52.32 cum 9504.75 497288.52 0

4 5.33 Providing and laying in position ready mixed M-25 grade

concrete for reinforced cement concrete work, using cement

content as per approved design mix, manufactured in fully

automatic batching plant and transported to site of work in

transit mixer for all leads, having continuous agitated mixer,

manufactured as per mix design of specified grade for reinforced

cement concrete work, including pumping of R.M.C. from transit

mixer to site of laying , excluding the cost of centering,

shuttering finishing and reinforcement, including cost of

admixtures in recommended proportions as per IS : 9103 to

accelerate/ retard setting of concrete, improve workability

without impairing strength and durability as per direction of the

Engineer-in-charge.

(Note :- Cement content considered in this item is @ 330 kg/

cum Excess/less cement used as per design mix is

5.33.2 All works above plinth level upto floor V leve 2.93 cum 9860.40 28890.97 0

Signature of Tenderer 43 Signature of NBCC

Rate In DSR Amount

S. N. Item No. DESCRIPTION OF ITEM TOTAL QTY UNIT Amount in

5 5.9 Centering and shuttering including strutting, propping etc. and

removal of form for

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

5.9.2 Walls (any thickness) including attached pilasters, butteresses,

plinth and string courses etc 192.00 sqm 842.50 161760 0

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Strut 36.00 sqm 961.30 34606.8 0

5.9.3 Suspended floors, roofs, landings, balconies and access platform

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers

6 5.22.6 Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all complete

upto plinth level & above plinth level. Thermo-Mechanically

Treated bars of grade Fe-500D or more 94.61 qtl. 10785.00 1020368.85 0

SH-13.0 FINISHING WORK

7 13.4.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand 133.92 sqm 343.65 46021.61 0

Sub-Total 46021.61 0.00

SH-19.0 DRAINAGE WORK

8 19.19.2 Supplying and fixing C.I. cover without frame for manholes :50

mm diameter C.I. cover (medium duty) the weight of the cover t

be not less than 58 kg 3.00 each 3441.20 10323.6 0

9 19.15.1 Providing M.S. foot rests including fixing in manholes with

20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse

sand : 6 graded stone aggregate 20 mm nominal size) as per

standard design : With 20x20 mm square bar 51.00 Nos. 544.70 27779.7 0

Sub-Total 38103.30 0.00

SH-22.0 WATER PROOFING WORK

Signature of Tenderer 44 Signature of NBCC

Rate In DSR Amount

S. N. Item No. DESCRIPTION OF ITEM TOTAL QTY UNIT Amount in

10 22.23 (AR) Providing and applying integral crystalline slurry of hydrophilic

in nature for waterproofing treatment to the RCC structures like

retaining walls of the basement, water tanks, roof slabs,

podiums, reservior, sewage & water treatment plant, tunnels /

subway and bridge deck etc., prepared by mixing in the ratio of

5 : 2 (5 parts integral crystalline slurry : 2 parts water) for

vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1

part water) for horizontal surfaces and applying the same from

negative (internal) side with the help of synthetic fiber brush.

The material shall meet the requirements as specified in ACI-

212-3R-2010 i.e by reducing permeability of concrete by more

than 90% compared with control concrete as per DIN 1048 and

resistant to 16 bar hydrostatic pressure on negative side. The

crystalline slurry shall be capable of self-healing of cracks up to

a width of 0.50mm. The work shall be carried out all complete

as per specification and the direction of the engineer-in- charge.

The product performance shall carry guarantee for 10 years

22.23.1 For vertical surface two coats @ 0.70 kg per sqm

22.23.2 For horizontal surface one coat @1.10 kg per sqm 21.11 sqm 362.80 7658.71 0

11 22.26 Providing and applying of swellable type water stop tape, 19 mm

x 25 mm thick in linear metre (expansive nature) for

construction joints treatment of RCC structure such as raft slab,

retaining walls, water storage tank and at the junctions of raft

slab with the retaining walls etc.. After cleaning the surface, one

coat of required primer for swellable water stop tape shall be

applied throughout the length of the joint @3.78 litre per 240

running metre. Over the primed surface swellable type water

stop tape shall be placed. The work shall be carried out all

complete as per specification and the direction of the Engineer-I

Charge. The product performance shall carry guarantee for 10

years against any leakage. 38.05 Rm 573.45 21819.77 0

Signature of Tenderer 45 Signature of NBCC

Rate In DSR Amount

S. N. Item No. DESCRIPTION OF ITEM TOTAL QTY UNIT Amount in

12 22.7.1 Providing and laying integral cement based water proofing

including preparation of surface as required for treatment of

balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of

admixed with water proofing compound conforming to IS. 2645

approved by Engineer-in-charge over the RCC slab including

walls upto 300 mm height including cleaning the surface before

(b) Laying brick bats with mortar using broken bricks/brick bats

(d) Finishing the surface with 20 mm thick jointless cement

1:4 (1 cement :4 coarse sand) admixed with water proofing

conforming to IS : 2645 and approved by Engineer-in-charge

laying glass fibre cloth of approved quality in top layer of plaster

finally finishing the surface with trowel with neat cement slurry

pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for

period of two weeks for curing and for final test. “All above

operations to be

done in order and as directed and specified by the Engineer-in-

22.7.1 With average thickness of 120 mm and minimum 26.46 sqm 1684.60 44574.52 0

Signature of Tenderer 46 Signature of NBCC

Rate In DSR Amount

S. N. Item No. DESCRIPTION OF ITEM TOTAL QTY UNIT Amount in

Sub-Total 128795.90 0.00

Signature of Tenderer 47 Signature of NBCC

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11,

TARAMANDAL, NEAR CIRCUIT HOUSE, OPP. RAMGARHTAL

LAKE, GORAKHPUR (U.P.)

Name of Work- Drain

COST OF RCC DRAIN (600 TO 1500)MM X (1200 TO 1500) MM

S.No. DESCRIPTION No. L B D/H QTY

LENGTH OF DRAIN

Along the Boundary 1 120.000 120.00

SAY IN LAC 21.88

Signature of Tenderer 48 Signature of NBCC

Detailed Estimate Based On DSR-2025 With Cost Index & Market Rate

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11, TARAMANDAL, NEAR CIRCUIT HOUSE, OPP. RAMGARHTAL LAKE, GORAKHPUR (U.P.)

Name Of Work -External Electrical Work

Rate as per D.S.R. 2025 MARKET BASED

Sr.No. Sch. No. Particulars Qty Unit Amount Rate Amount

A Subhead-I HT Work

1 11 KV DOUBLE POLE STRUCTURE

Supply, erection, testing and commissioning of 2 pole structure for providing 1

MR No. 11KV,200A GOS in accordance with IE rules, & local authority 1.00 Set 1,25,000.00 1,25,000.00

specification and drawings and comprising of the following.

a. 2 Nos. 11 mtr. long MS STEEL poles complete with, pole excavation, MS

STEEL foundation, and back filling complete MS steel channel/angle iron etc.

b. 1 Set of cross arms, branching, clamps and painting complete with GI nut,

bolts & washers as required (for GO & DO), LA connection.

c .1 set 11KV Insulator complete with spindles & hardware complete as

d .1 No. 11KV 400A TP Gang operated Air break switches complete with

25mm dia GI pipe operating machanism, handle & locking arrangement.

e. 1 set of 3 nos.11KV single pole drop out fuse complete with barrel fuses, an

mounting arrangement.

f. 1 set (3 nos.) 11KV lightning arrestor and connecting to all phases. - -

g. 4 No. 150 mm dia 6 meter long GI pipe class 'B' (for XLPE cable

protection) as required.

h. 2 Set 50mm dia 3m long GI pipe earting with 25 x 6 mm GI earth strip

complete as required (for GO & DO & LA)

i 1 nos. 11KV HT danger boards and 2 set of anticlimbing devices. - -

11 KV Double Pole Structure described below - -

Supply of 3 core standered aluminium conductor XLPE (Cross linked

polyethylene) insulated PVC bedded, Galvanised flat steel strip armoured

cables confirming to I.S. 7098 (Part-II with latest amendments) II KV grade as

per requirement.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable

3 22.3 of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe - - -

supplying and making indoor cable end termination with heat

shrinkable jointing kit complete with all accessories including lugs suitable for

following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as

Signature of Tenderer

49 Signature of NBCC

Supplying and making outdoor cable end termination with heat shrinkable

jointing kit complete with all accessories including lugs suitable for following

5 23.5 size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : - - -

Supply and laying of 1800mm x 900mm x 12mm thick chequered rubbbber

matting of tested quality.

Supply and fixing of shock treatment chart (prescribed under I.E. rules) duly

7 MR framed with glass and supported from back with hard board or soft board with 3.00 Each - 247.98 743.93

supply of all material labour T&P for proper completion of work.

Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked

IS : 2878 & TAC approved) complete with initial charge and wall bracket,

along with supply of all materials and labour for proper completion of work.

Supply and laying of PVC Insulated, FRLS Round Sheathed Multi Core

Industrial Flexible Cable conforming to IS 694:2010 with Flexible Bright

9 Annealed Copper Conductor for Voltage Grade 1100 Volts as per direction of - - -

engineer incharge.

HT Panel - - -

Supply, erection, testing and commissioning of 1 panel, 630A ,11 kV, 3 Phase,

50 Hz., metal clad, dead front, 350 MVA rupturing capacity Vacuum Circuit

Breaker Incoming & Outgoings as per the detailed specifications and drawings

Outgoings as per the detailed specifications and drawings including

10 connections etc. complete with following in-comers including connections etc. - - -

complete with following in-comers and out-goings including door interlocking

panel should be expendable type complete as per technical specifications and a

A. INCOMER 1nos.: -

i) 1 No. VCB having following -

1 No. 630A, 11kV, 3 Phase, 50Hz., metal clad, dead front, 350 MVA

rupturing capacity, Fully Drawout type, Vacuum Circuit Breaker (VCB)

1 set of 11kV/110V Potential Transformers with MCB -

1 Set of Phase indicating lamps with MCB -

1 No. 0-11 kV Digital voltmeter with selector switch -

1 set of indicating lamps to indicate OPEN, CLOSE, TRIP,SPRING

CHARGED, TRIP CIRCUIT HEALTHY

Push button for ON, OFF,TRIP&TRIP circuit healthy -

1 set of 80/5-5A Current Transformer for metering and protection -

1 No. 0-100 digital Amps ammeter with selector switch -

1 Set of CDG 31 (2 No. O/C, 1 No. E/F) relay -

Digital frequency meter,Digital Tri vector meter. -

I Set of undervoltage relay and Overvoltage relay -

Trip circuit supervision relay,Auxiliary relays with shunt trip coil -

Signature of Tenderer

50 Signature of NBCC

I No. Master Trip relay -

1 No. Digital Power factor meter -

Total For Subhead-I HT Work 1,73,394.00 12,13,580.47

B Subhead-II Transformer

1 TRANSFORMER - -

11/0.433 KV, 3 Phase, 50 Hz outdoor/ indoor mounting(Mineral oil

Supply, installation, testing and commissioning of following capacity

(continuous loading) BEE 5 Star rated (Corresponding Level as per BIS

amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase, 50

Hz, Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound

transformer (Electrolytic grade 99.9% pure copper, Core made of first

grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better,

suitable for out door/indoor applications with On Load Tap Changer (OLTC)

on HV side having AVR relay and Remote Tap Changer Control (RTCC) for

automatic sensing of incoming voltage, automatic operation of OLTC and

facility for remote and manual operation of OLTC HV side in range of +5% to

-15% in steps of 2.5%, having cable end boxes on HV side suitable for -

3x300 sqmm XLPE cable of 11 KV grade, including bus trunking

arrangement on LV side including supplying and laying of copper conductor

multicore control cable from transformer to HT breaker/panel for safety

tripping, complete with all accessories and safety provisions as per relevant

IS Code including first filling of filtered dehydrated oil, i/c supplying and

grouting of suitable M.S. Channel with all accessories and transformer shall

be confirming to IS : 2026 (Part 1 to Part 5), IS : 1180 and duly ISI Marked

as per CPWD specifications complete in all respects etc as required at site.

The maximum flux density in any part of the core and yoke at rated voltage

and frequency shall be such that the flux density with + 12.5 percent

combined voltage and frequency variation from rated voltage and frequency

does not exceed 1.9 Tesla. The permissible temperature-rise shall not

exceed 35 dg.C for oil and 40 dg. C up to 200 KVA and 40 dg.C for oil and 45

dg. C for above 200 KVA for winding. Inside of tank shall be painted with

varnish or liquid resistant paint. For external surfaces one coat of thermo

setting powder paint or one coat of epoxy primer followed by two coats of -

polyurethane base paint shallbe used. IS: 1180 (Part 3) shall be referred to

for paint thickness for normal to medium corrosive atmosphere. For highly

polluted atmosphere and special application external paint work shall be as

per direction of Engineer-in-Charge. Design ambient condition : a) air

temperature 50 deg C, b) Relative Humidity 90 % Max, c) Seismic Zone as

Signature of Tenderer

51 Signature of NBCC

per location of site, d) Altitude as per location/site. Noise level Shall not

exceed limits as per NEMA TR-1 with all accessories running measured as

per IEC 551 / NEMA standard. The transformer should have QR code which

should contain drawing, test report OEM manual,Geo- Tag of manufacturing

location etc. Marking Each transformer shall be provided with rating plate -

made of anodized aluminum/ stainless steel material securely fixed on the

outer body, easily accessible,as per IS: 1180 Part-3. The entries on the rating

plate shall be indelibly marked.

Fitting and Accessories : The following fittings shall be provided:- a) Two

earthing terminals with the earthing symbol b) Oil level gauge indicating oil

level at minimum, 30°C and maximum operating temperature; c) Air release

device (for non-sealed type transformers) d) Rating and terminal marking

plates; e) Silica gel breather f) Drain-cum-sampling valve (¾ ″ nominal size -

thread, IS 554) preferably steel with plug for three phase transformers; g)

Thermometer pocket with cap; h) Oil filling holes having (1¼ ″ nominal size

thread) with cover (for sealed type transformers without conservator); i)

Lifting lugs for the complete transformer as well as for core and winding

assembly; j) Pressure relief device or explosion vent above 200 kVA; k) One

filter valve on the upper side of the tank (for transformers above 200 kVA); l)

Unidirectional flat rollers (for transformers above 200 kVA); m) Inspection -

hole (for transformers above 200 kVA); n) HV side neutral grounding strip

(where one of the HV bushing terminal is connected to earth);

o) Buchholz relay for transformers above 800 kVA. p) Arcing horns or

suitable rating lightning arrestors for HT side – 3 Nos. q) Bird guard; r) Oil

temperature indicator and winding temperature indicators for transformers

above 200 kVA with suitable tripping mechanism above permissible limit s)

Jacking pads (for transformer above 1600 kVA); t) Additional Neutral

separately brought out on bushing for earthing. u) Magnetic oil level gauge

24.9 (for transformer above 1600 kVA) with low oil level alarm contact; v) Non -

return valve (for conducting pressure test); w) Pressure relief device or

explosion vent x). Monogram Plate y) Inspection cover z). Detachable type

radiators with top and bottom shutoff valve. aa) Oil Conservator with Oil level

indicator, minimum level marking and drain plug for all transformers of

capacity 50 KVA and above. bb) Necessary hardware, clamps, lugs etc. for

termination on HV/MV etc. for all transformers.

Total For Subhead-II Transformer 9,95,660.00 -

C Subhead-III DG Set

Supply, installation, Testing & Commissioning of 'Silent Type Diesel

Generating set as per CPCB IV + or better norms along with having Prime

Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power

factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor,

29.1 including testing at factory and site with fuel, load for test and other - -

necessary arrangements Complete as per CPWD specifications, should

have QR code which should contain drawing, test report OEM manual,Geo-

Tag of manufacturing location, rating plate as per relevant IS Code etc. and

consisting of the followings:

Signature of Tenderer

52 Signature of NBCC

(A) Diesel Engine:

Turbocharged Diesel engine 4 stroke water cooled, multi cylinder,

dynamically balanced fly wheel, electric start of suitable BHP at 1500 RPM

suitable for above output of alternator at 40 Degree C, 50% RH & at 1000

Meter MSL , capable of taking 10% over loading for one hour after 12 hours

continuous operation. The engine will be with Electronic governor, Dry type

Air filter with service indicator, first filling of engine fuel (after

lubricating Oil, Coolant and other consumables complete with all the

required accessories, the Electronic governor shall be as per ISO 8528.The

engine shall comply to the latest CPCB norms (CPCB IV + or better) and

Conforming to BS 5514, BS 649, IS 10000, IS 10002, IS 13018 and as per

CPWD specifications.

(B) Engine mounted Instrument Panel fitted with and having digital display

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication and Voltage indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lubricantion Oil trip indication

(ix) Engine Running Hours indication

(C) Alternator:

Synchronous alternator rated of appropriate KVA, 415 volts at 1500 RPM, 3

phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50%

RH & at 1000 Meter MSL. The alternator shall be having Screen Protected

Drip Proof (SPDP) enclosure IP23, brushless, continuous duty, dynamically

balanced rotor, capable of taking 10% over loading for one hour after 12

hours of continuous operation, self cooled,self-excited and self-regulated

through AVR conforming to IS13364(Part 2)/IS: 4722/BS 2613 suitable for

tropical conditions and with class- H insulation.

(D) Base Frame & Foundation:

Both the engine and alternator shall be mounted on suitable base frame

made of MS channel with necessary reinforcement which shall be installed

on suitable cement concrete foundation and vibration isolation arrangement

as per recommendations of manufacturer.

Signature of Tenderer

53 Signature of NBCC

Daily service fuel tank of suitable liters capacity as per CPWD Specifications,

fabricated out of 3 mm thick M.S. sheet complete with all standard

accessories and fuel piping between fuel tank and diesel engine with MS

class 'C' pipes of suitable dia. Complete with valves, level indications &

accessories as required as per specifications.

(F) Exhaust System:

Dry exhaust manifold with hospital type exhaust silencer and catalytic

(G) Starting System:

12V/24V DC starting system comprising of starter motors: voltage

regulator and arrangement for initial excitation complete with suitable

numbers of batteries (180 AH capacity lead acid SMF type) as required as

per specifications. The battery shall be housed inside the acoustic enclosure

(H) Acoustic and weather proof enclosure with arrangement for fresh air

intake for cooling of the engine & alternator, extraction, discharging hot air in

to the atmosphere and the temperature rise inside the enclosure, noise level

outside enclosure. The acoustic enclosure should be suitable for cable

connection/connection through bus-trunking. Such arrangements on

acoustic enclosure should be water proof & dust-proof conforming to IP-65

protection. The enclosure shall be as per CPCB IV + or better norms etc. and

as per CPWD specifications.

Free standing floor mounted IP 42 automatic mains failure control panel

including auto by-pass, suitable for KVA as below for silent type DG set

complete with relays, timers, set of CTs for metering & protection and energy

analyser to indicate currents, phase and line voltages, frequency, power

factor, KWH, Kilo Volt Ampere Reative Hour (KVARH), KVA (Phase &

KW & provision for overload, short circuit, restricted earth fault, under

frequency, power (aluminum) and control (copper ) cabling of suitable size

upto 15 meter between AMF panel, LT Panel and DG Set including

connection interconnection etc. as required, all complete and inter locking

and communication/ Ethernet /RS485/SNMP port open protocol for BMS

integration including suitable software, the panel shall be of DG Set OEM

make etc. as per approved by Engineering in charge and including the

Signature of Tenderer

54 Signature of NBCC

1. Suitable numbers and appropriate capacity 4 pole motorised

electrically operated draw out with cradle type 3 position ACB/ MCCB

with electronic release for O/C & E/F and shunt trip.

2. Auto/Manual/Test/Off selector switch

3. Protection for under and over voltage phase reversal (2 nos Over

voltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage

4. 3 Sets of current transformers 15 P 10 accuracy for protection and 15

VA class-I for metering

5. Energy analyser unit to indicate current, Voltage( L-N & L-L), kW, kVA

(Phase & Total), Frequency, KWH, PF.

6. LED Indicating lamps for load on mains and load on set.

7. Fuse/ MCB for instruments.

8. Battery charger, complete with transformer/ rectifier, D.C. voltmeter

and ammeter, selector switch for trickle, off and boost and current

9. Main supply failure monitor.

10. Supply failure timer.

11. Restoration timer

12. Control unit with three impulse automatic engine start/stop and failure

to start lockout.

13. Impulse counter with locking and reset facility.

14. ON/OFF/Control circuit switch with indicator

15. Audio/Video annunciation for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

16. Protection for over/under Frequency, Loss of AC sensing, Over

Current, Unbalancing load with suitable number of relays and

17. Maintenance notification based on Engine Run Hour & due date.

18. Load Management through PLC to achieve auto opening and closing of

incomer breakers, bus coupler switching of essential panel ,

interlocking providing signal to AMF Panel for load status and AMF

shall give command to DG Set to auto start / auto stop depending upon

load status and requirement etc. and necessary hardware and

software required to perform the operation shall be provided by the

contractor including all control wiring.

Total For Subhead-III DG Set 12,49,613.00 -

D Subhead-IV Distribution Panel

Signature of Tenderer

55 Signature of NBCC

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz

power distribution system. The panel shall be Indoor, free standing, floor

mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type

compartmentalised design fabricated out of 14 SWG CRCA sheet steel,

complete with colour coded, heat shrinkable PVC insulated, aluminium bus

bars and separate earth bus bar of adequate cross section through out the length

of the panel. The incoming and outgoing feeders shall be accommodated in a

fully segregated, modular multitier arrangement with adequate size and distinc -

cable alley, bus bar alley/chamber. The panel shall be complete with name

plate, earthing, numbering, danger plate etc. as per specifications and drawings

as required. The panel shall withstand the fault level of 50kA as per Single

Line Diagram. The Panel shall also be capable to communicate status like

ON/OFF/ Trip through Modbus/Ethernet for major component like ACB,

MCCB, MCB & Multifunation meters.

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have

Buscoupler switching, auto operation of incommer and bus coupler, auto start

of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and -

having following incomming and outgoing Air Circuit

Breakers,microprocessor release for overload, short circuit, instantaneous &

earthfault protection with Current & Voltage metering & LCD display.

Air Circuit Breaker with microprocessor release ge metering & LCD display ,

with ready to clsoe indicator, should have capability to communicate ON

/OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of

ACB (Icu=Ics=Icw=65 KA (1 sec). MCCB, with microprocessor release with

LSIG protection functionand should not derate upto 50 decree Centrigrate as

per testing guideline as per IEC 60947-2 and all the ACB upto 2500Amp -

ACB should have same frame size LCD display for fault trip history, haivng

current limiting feature, double break mechanism & capability to communicat

ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics)

1 Nos. 800 Amp FP ACB 25KA LSIG having S/C, E/F O/C protection, LCD

Display having specs as per attached annexture From 400KVA Transformer

R,Y,B Phase indication Lamp with control MCB -

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 320 Amp FP MCCB 25KA LSIG having S/C, E/F O/C protection,

LCD Display having specs as per attached annexture From 160KVA DG Set

R,Y,B Phase indication Lamp with control MCB -

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

Signature of Tenderer

56 Signature of NBCC

1 Nos. 63 Amp FP MCCB 25KA LSIG having S/C, E/F O/C protection, LCD

Display having specs as per attached annexture From 20KWp On Grid Solar

R,Y,B Phase indication Lamp with control MCB -

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 320 Amp FP ATS 25KA -

1 Nos. 1000 Amp FP busbars of aluminium alloy as per SLD. -

1 Nos. 400 Amp FP busbars of aluminium alloy as per SLD. -

1 Nos. 320 Amp TP MCCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

APFC PANEL + SPARE

2 Nos. 400 Amp FP MCCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

2 Nos. 200 Amp FP MCCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

L+P PANEL + SPARE

2 Nos. 100 Amp FP MCCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

STP PANEL + SPARE

5 Nos. 63 Amp FP MCB 10 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

EX.LIGHT+PL+FF+SPARE

3 Nos. 32 Amp DP MCB 10 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

Short Circuit Breaking capacity should not less than 10KA. -

RELAYS AS PER SLD - -

Signature of Tenderer

57 Signature of NBCC

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz

power distribution system. The panel shall be Indoor, free standing, floor

mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type

compartmentalised design fabricated out of 14 SWG CRCA sheet steel,

complete with colour coded, heat shrinkable PVC insulated, aluminium bus

bars and separate earth bus bar of adequate cross section through out the length

of the panel. The incoming and outgoing feeders shall be accommodated in a

fully segregated, modular multitier arrangement with adequate size and distinc -

cable alley, bus bar alley/chamber. The panel shall be complete with name

plate, earthing, numbering, danger plate etc. as per specifications and drawings

as required. The panel shall withstand the fault level of 50kA as per Single

Line Diagram. The Panel shall also be capable to communicate status like

ON/OFF/ Trip through Modbus/Ethernet for major component like ACB,

MCCB, MCB & Multifunation meters.

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have

Buscoupler switching, auto operation of incommer and bus coupler, auto start

of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and -

having following incomming and outgoing Air Circuit

Breakers,microprocessor release for overload, short circuit, instantaneous &

earthfault protection with Current & Voltage metering & LCD display.

Air Circuit Breaker with microprocessor release ge metering & LCD display ,

with ready to clsoe indicator, should have capability to communicate ON

/OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of

ACB (Icu=Ics=Icw=65 KA (1 sec). MCCB, with microprocessor release with

LSIG protection functionand should not derate upto 50 decree Centrigrate as

per testing guideline as per IEC 60947-2 and all the ACB upto 2500Amp -

ACB should have same frame size LCD display for fault trip history, haivng

current limiting feature, double break mechanism & capability to communicat

ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics)

1 Nos. 200 Amp FP MCCB 16KA

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB -

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 250 Amp FP busbars of aluminium alloy as per SLD. -

5 Nos. 63 Amp FP MCB 10 KA

5 Nos. 32 Amp FP MCB 10 KA

3 Nos. 63 Amp FP MCCB 10 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

Signature of Tenderer

58 Signature of NBCC

2 Nos. 100 Amp FP MCCB 10 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

Short Circuit Breaking capacity should not less than 10KA. -

RELAYS AS PER SLD - -

3 MR UPS OUTPUT PANEL 1.00 Set 93,500.00 93,500.00

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz

power distribution system. The panel shall be Indoor, free standing, floor

mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type

compartmentalised design fabricated out of 14 SWG CRCA sheet steel,

complete with colour coded, heat shrinkable PVC insulated, aluminium bus

bars and separate earth bus bar of adequate cross section through out the length

of the panel. The incoming and outgoing feeders shall be accommodated in a

fully segregated, modular multitier arrangement with adequate size and distinc -

cable alley, bus bar alley/chamber. The panel shall be complete with name

plate, earthing, numbering, danger plate etc. as per specifications and drawings

as required. The panel shall withstand the fault level of 50kA as per Single

Line Diagram. The Panel shall also be capable to communicate status like

ON/OFF/ Trip through Modbus/Ethernet for major component like ACB,

MCCB, MCB & Multifunation meters.

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have

Buscoupler switching, auto operation of incommer and bus coupler, auto start

of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and -

having following incomming and outgoing Air Circuit

Breakers,microprocessor release for overload, short circuit, instantaneous &

earthfault protection with Current & Voltage metering & LCD display.

Air Circuit Breaker with microprocessor release ge metering & LCD display ,

with ready to clsoe indicator, should have capability to communicate ON

/OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of

ACB (Icu=Ics=Icw=65 KA (1 sec). MCCB, with microprocessor release with

LSIG protection functionand should not derate upto 50 decree Centrigrate as

per testing guideline as per IEC 60947-2 and all the ACB upto 2500Amp -

ACB should have same frame size LCD display for fault trip history, haivng

current limiting feature, double break mechanism & capability to communicat

ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics)

1 Nos. 100 Amp FP MCCB 16KA

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB -

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 125 Amp FP busbars of aluminium alloy as per SLD. -

Signature of Tenderer

59 Signature of NBCC

3 Nos. 63 Amp FP MCB 10 KA

2 Nos. 32 Amp FP MCB 10 KA

2 Nos. 32 Amp DP MCB 10 KA

Short Circuit Breaking capacity should not less than 10KA. -

RELAYS AS PER SLD -

4 25.1 Automatic Power Factor Correction (APFC) System

Supply, Installation, testing and commissioning of Automatic Power Factor

Correction (APFC) panel, indoor type floor mounted free standing totally

enclosed, extendable, IP 42, of following capacity for 3 phase, 415 V + 10 %,

50 Hz AC System for Ambient temperature -5°C to +40°C, fabricated in

compartmentalised designed made of CRCA sheet steel of 2.0mm thick for

framework & covers, 3 mm thick for gland plate i/c cleaning & finishing

complete with 9 tank process for powder coated of approved

shade having front section (switch gear

and control accessories) and rear section capacitor

and reactor, front and rear access, having suitable

current carrying capacity, extensible TPN Aluminium

alloy bus bar of high conductivity, DMC/SMC bus bar -

supports, bottom base channel of MS Section,

fabrication shall be done in transportable section,

entire panel shall have common copper earth bar of

minimum size of 25mm x 5mm with 2 nos. earth

studs, the earth terminals provided on the body of

capacitor bank shall also be bonded to the main

capacitor panel earth bus with 2 nos. 8 SWG or 6

SWG GI earth wires/ equivalent size of copper

conductor cable, forced ventilation for maintaining

temperature rise not more than 5°C from ambient,

Signature of Tenderer

60 Signature of NBCC

interconnections, connections with 14% detuned

reactor and heavy duty 525 V ISI marked Impregnated

MPP(Metalized Polypropylene) Capacitor (IS 13340

Part -1 & 2) APFC Panel shall be in compliance with

IS :16636 & CPWD Specifications etc.

as per below details.

Suitable capacity MCCB Microprocessor base with

O/C, S/C, E/L release of TPN 50KA breaking capacity

(Ics=Icu), ON, OFF, Trip, R, Y, B - LED Indicating

Lamp set along with required Instruments and

accessories with extended rotary handle and door

interlocking arrangement. Current rating of theIncomer in ampere shall be

APFC Panel rating in -

KVAR x 1.4 x 1.5 or Nearest higher standards rating.

(B) Instruments & Indications

i) 3-Phase current sensing APFC microprocessor

relay/controller , advance 8/12 stages (8 stages for

capacity below 100 KVAR and 12 stages 100 KVAR &

above) with Communication Ethernet/RS485/SNMP

port open protocol for BMS integration as per

approved by Engineering in charge and having

display of Phase wise V, A, PF, Cos-Phi, Kw, KVA,

KVAR, THD-V , THD-I, harmonics up to 31 level. 3

nos of dual core CT's accuracy class 1, 15VA at

incomer of PCC Panel for APFC relay.

Signature of Tenderer

61 Signature of NBCC

ii) Auto Manual Selector switch, auxiliary contactors

with timer for delay in manual mode.

iii) Digital Multi function meter with LED Display for V,

A, PF, KW, KVA, KVAR, THD-V & I, Frequency.

iv) Suitable rating control transformer shall be provided

for control and indication circuit.

v) All components like control transformer, meter, relay

and indicating lamp shall be protected by using

suitable rating individual MCB's.

vi) Wiring of the control circuit shall be done by using

2.5 sq mm, FRLS/HFFR 1100 V grade, PVC insulated

multi stranded copper control wire.

(C) Bus Bars 1.3 Amp per Sq.mm,TPN, Electrolytic

grade Aluminium bus bar of capacity 1.25 times of -

incomer rating as per CPWD specification.

(D) Outgoings (APFC Section) Selection of the

capacitors combinations shall be for continuous

rating and each capacitor bank shall have suitable

capacity Heavy Duty ISI Marked Capacitor, capacitor

duty contactor,the capacitor shall be mounted on

channel with base of perforated M S Powder coated

sheet, connections inter connections etc. and other

features as per CPWD Specifications and relevant IS

Code having following:

(i) Capacitor bank ratings & stages shall be as per the

technical specifications sheet of NIT.

(ii) Capacitor will be MPP self healing type with

discharge resistor, pressure release mechanism.

(iii) Since Capacitor Voltage is 525 Volts, thus higher

KVAR has to be considered to get rated output at 415

Volts.(iv) 14% Detuned Reactor of class H insulation &

150% linearity in series with Capacitor.

(Note: Technical specifications sheet for selection of

the capacitors combinations shall be provided by the

NIT Approving Authority with due consideration of

number of capacitors i.e. 1 KVAR, 2 KVAR, 3 KVAR, 5

KVAR, 10 KVAR.....for smooth correction).

Total For Subhead-IV Distribution Panel 3,20,033.00 5,97,500.00

E Subhead-V L.T Cable Work

Supply and laying of aluminium conductor PVC insulated armoured serve

sheathed cables 1100 Volts grade on cable tray as directed by engineer

incharge complete in all respect including The armouring of the cable shall be

properly connected with the earth conductor by clamps etc.

Signature of Tenderer

62 Signature of NBCC

Supply ofPower/Control Copper Cables,Solid Copper conductor,XLPE

Insulated,cores laid up, PVC tape innersheathed,Unarmoured/Armour

2 MR (Glavanised wire for cables up to 14x1.5 sqmm, 9x2.5 sqmm,2x16 sqmm, - -

3x10 sqmm,4x10sqmm balance all galvanised steel strip),extruded PVC Type

ST2 Sheathed, 650/1100 V grade as per IS 7098 (Part 1) 1988

Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

3 aluminium conductor cable of 1.1 KV grade as required. - -

Laying of one number PVC insulated and PVC sheathed / XLPE

4 10.5 power cable of 1.1 KV grade of following size in the existing -

RCC/ HUME/ METAL pipe as required.

b 10.5.2 Above 35 sq. mm and upto 95 sq. mm 30.00 Meter 72.00 2,160.00 -

d 10.5.4 Above 185 sq. mm and upto 400 sq. mm 150.00 Meter 170.00 25,500.00 -

Laying and fixing of one number PVC insulated and PVC

5 10.8 sheathed / XLPE power cable of 1.1 KV grade of following size -

on cable tray as required.

a 10.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) 100.00 Meter 53.00 5,300.00 -

b 10.8.2 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) 70.00 Meter 109.00 7,630.00 -

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat

d 10.8.4 Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clam 110.00 Meter 226.00 24,860.00 -

Providing, laying and fixing following dia RCC pipe NP2 class

(light duty) in ground complete with RCC collars, jointing with

cement mortar 1:2 (1 cement : 2 fine sand) including trenching

(75 cm deep) and refilling etc as required. 300mm Dia

Signature of Tenderer

63 Signature of NBCC

Supplying and laying of following size DWC HDPE pipe ISI marked along

with all accessories like socket, bend, couplers etc.

conforming to IS 14930, Part II complete with fitting and cutting,

jointing etc. in the existing trench, complete as required

Total For Subhead-V L.T Cable Work 2,01,582.00 7,06,001.51

F Subhead-VI External Lighting Work

EXTERNAL LIGHT FEEDER PILLAR -

Supply installing testing & commissioning of out door type IP66 with

additional canopy street light feeder pillar (Distribution Panel)

1 MR compartmentalised design, dust tight & vermin proof made out of 14 gauge 1.00 Each 90,000.00 90,000.00

M.S. sheet, stove powder coated complete as required with following

incomming & outgoing as per detail below.

63 Amp. 10 KA FP MCCB 1 No. -

Suitable digital contractor and timer for down & dusk -

100 Amp. TPN Alu. Bus bar -

32 Amp. 10KA DP MCB 9 No. -

40 Amp. 10KA FP MCB 2 No. -

Supply and laying of aluminium conductor PVC insulated armoured serve

sheathed cables 1100 Volts grade in existing RCC / Hume / metal pipe as

2 MR directed by the Engineer-Incharge, complete in all respect. The armouring of - -

the cable shall be properly connected with the earth conductor by clamps etc.

Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

3 aluminium conductor cable of 1.1 KV grade as required. - -

Supplying and laying of following size DWC HDPE pipe ISI marked along

with all accessories like socket, bend, couplers etc.

conforming to IS 14930, Part II complete with fitting and cutting,

jointing etc. in the existing trench, complete as required

Signature of Tenderer

64 Signature of NBCC

Supply and burying of 40mm dia x 4.5 metres long G.I. Pipe vertically for

earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre

from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I.

Pipe up to appron (and from appron to switch board the cost of G.I. wire and

5 5.2 pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover 2.00 each 7,658.00 15,316.00 -

masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at

least 150mm thick alround etc. as per directions of Engineer-in-charge

complete in all respects as per drawing.

Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for

earthing with its top at least 3 metres below ground level complete with 20mm

dia G.I. pipe and funnel for watering and one earthing lead of two no. 8 to 10

SWG GI wire in 15mm dia G.I. pipe up to switch board (from appron to

6 switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. 2.00 each 8,351.00 16,702.00 - -

frame with hinged cover masonry housing alternate layers of charcoal/coke an

salt at least 150mm thick alround etc. as per directions of Engineer-in-charge

complete in all respect.

Supply and laying of 25 mm X 3mm G.I. strip from earth electrode directly in

the ground as required complete in all respect.

Supply and fixing of 1 no. 8SWG GI wire in 15mm dia GI pipe for earthing,

laid in ground or in wall duly concealed including the cost of cement, sand,

labour, T&P other material required for proper completion of the work as

directed at site.

Supply & fixing of 3 mtr pu painted decorative pole alongwith foundation

work etc as required.

Supplying, Installation, Testing & Commissioning of LED Post Top Light

Fixture with powder coated pressure die cast aluminium housing and UV

stabilized polycarbonate diffuser, complete with high efficiency constant

current driver, suitable for outdoor applications. Driver efficiency>85%, input

voltage 140–270 Volt AC, frequency 50/60 Hz, operating temperature range -

5°C to +50°C, internal surge protection of 5 kV (L, N, E) as per IEC 61000-4-

5, THD <10% as per IEC 61000-3-2, Power Factor ≥0.95, IP66 protection,

IK08/IK10 impact resistance, CRI >70, under voltage and over voltage

protection, EMI/EMC as per CISPR-15, symmetric light distribution (IES

Type V) suitable for parks, pathways, landscaped areas and pedestrian zones.

Fixture suitable for top entry mounting on 76 mm O.D. pole (or up to 76 mm

spigot) complete with all mounting accessories.

MR Luminaire shall have a minimum life of 50,000 burning hours with L70 lumen -

maintenance as per LM-80 extrapolated through IES TM-21. Colour

Temperature 3000K / 4000K / 5700K / 6500K (as approved by Engineer-in-

Charge), SDCM <5, maximum power consumption shall not exceed the

specified rating. Fixture shall conform to relevant BIS standards complete in

all respects including external connections with 1.5 sq.mm FRLS/HFFR PVC

insulated copper conductor single core cable, earthing, glands, ferrules and all

accessories as required.

LM-79 & LM-80 Test Reports and all testing certificates required as per BIS

shall be submitted. Thermal management shall be through an aluminium heat

sink such that the LED junction temperature shall not exceed 90°C. The fixtur

shall be supplied with a minimum 5-year OEM warranty.

Signature of Tenderer

65 Signature of NBCC

Total For Subhead-VI External Lighting Work 59,212.00 4,83,079.52

G Subhead-VII Earthing Work

Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for

earthing with its top at least 3 metres below ground level complete with 20mm

dia G.I. pipe and funnel for watering and one earthing lead of two no. 8 to 10

SWG GI wire in 15mm dia G.I. pipe up to switch board (from appron to

1 switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. 6.00 each 8,351.00 50,106.00 - -

frame with hinged cover masonry housing alternate layers of charcoal/coke an

salt at least 150mm thick alround etc. as per directions of Engineer-in-charge

complete in all respect.

Supply and burying of 600mm x 600mm x 3mm copper plate vertically for

earthing with its top at least 3 metres below ground level complete with 20mm

dia G.I. pipe and funnel for watering and two earthing lead of two no. 8 SWG

copper wire in 15mm dia G.I. pipe up to switch board (from appron to switch

2 board the cost of G.I. pipe and copper wire will be extra) 30cm square C.I. 4.00 each 15,004.00 60,016.00 - -

frame with hinged cover masonry housing alternate layers of charcoal/coke an

salt at least 150mm thick alround etc. complete in all respect.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground

as strip earth electrode, including connection/ terminating with nut, bolt,

spring, washer etc. as required. (Jointing shall be done by overlapping and with

2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as

strip earth electrode, including connection/ terminating with G.I. nut, bolt,

spring, washer etc. as required. (Jointing shall be done by overlapping and

with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from

5 5.10 earth electrode including connection with brass nut, bolt, spring, washer 40.00 Meter 1,638.00 65,520.00 - -

excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from

6 5.11 earth electrode including connection with G.I. nut, bolt, spring, washer 60.00 Meter 755.00 45,300.00 - -

excavation and re-filling etc. as required.

Total For Subhead-VII Earthing Work 3,07,022.00 -

H Subhead-VIII Panel Protection System

2kg capacity seamless Alluminium cylinder Paso approved stored pressure

type clean agent fire extinguisher alongwith all necessary fitting filled with

clean agent FK-5-1-12 complete having operating pressure between 15 bar etc.

as required UL & FM listed gas.

SITC of Pneumatic Heat detection tube red color made by special modified polyamide

(PA), UL and LPCB standard, having burst temperature 100°C to 120°C, inner

diameter 4 mm, outer diameter 6 mm, pressurized with nitrogen at 15 bar pressure for

automatic detection and suppression system

Signature of Tenderer

66 Signature of NBCC

SITC of End of line adapter along with pressure gauge working pressure 25 bar. UL

SITC of End of Line Plug for automatic fire suppression System used for fitting at

5 MR tube end to terminate the point. Fitting made by brass nickel plated material. UL 4 Each 4,560.00 18,240.00

6 MR SITC of Pressure Switch at 15 bars. UL approved. 4 Each 7,990.00 31,960.00

SITC of T connection suitable for 4 / 6 mm. diameter pressurized tubes, brass nickel

plated material with maximum working pressure 25 bar. UL approved

SITC of Master Control Unit micro processor based 4 zone inbuilt GSM dialer audio

visual alarm control panel, 2NO/NC potential free relay contacts discharge LED

indicator, battery LED indicator, system status indicator and AC power ON LED

indicator with inbuilt battery backup 24h

Total For Subhead-VIII Clean Agent Suppression System - 5,15,950.00

I Subhead-IX Cable Tray Work

Supplying and installaton following size of perforated painted with powder

coating M.S. cable trays with perforation not more than 17.5%, in convenient

46 sections, joined with connectors, suspended from the ceiling with two numbers - - -

MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts & nuts, painting

suspenders, fastener etc as required

a 4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness 20.00 Meter 623.00 12,460.00 - -

c 4.1.10 450 mm width X 62.5 mm depth X 2 mm thickness 20.00 Meter 1,348.00 26,960.00 - -

Total For Subhead-IX Cable Tray Work 39,420.00 -

J Subhead-X On Grid Solar Power Backup System

On Grid Solar System Work

Signature of Tenderer

67 Signature of NBCC

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic

Power Plant conformington MNRE specifications as amended, consisting of

Mono Crystalline silicon solar cells, netmetering facility, necessary protection

earthing, mounted on Aluminium/GI structure of suitable strength with

following components complete as required:-a)Solar Photovoltaic Module of

1 17.1 capacity 330Wp or above, manufactured in India, conforming to 20.00 KWp 54,280.00 10,85,600.00 - -

IS14286/IEC61215, IS/IEC61730-Part-1, IS/IEC61730-Part-2. Solar

Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV

modules used in solar power plants/systems must be warranted for their output

peak watt capacity, which should not be less than 90% at the end of 10years

and 80% at the end of 25 years

b)Power Conditioning Unit (PCU) of 350-800VDC Input voltage range and

400VAC, three phase, 4wire, 50Hz+/-2.5Hz, out put voltage suitable to

generate AC Power with efficiency not less than 97%, total harmonic distortio

less than 3% and suitable for ambient temperature from 0to50degree C. The

PCU shall adjust the voltage and frequency level to suit the Grid Voltage

Frequency.c) Data Monitoring System complete with accessories.

d) Fixing of Array junction box & Main junction box with IP65 protection and

termination arrangement for in coming and outgoing cable alongwith glands,

lugs and other accessories etc. as required.

e) Lightning and surge voltage

protection.f)Connections&Interconnectionsbysupplying&fixingrequiredsizeXL

PEinsulatedcopperconductor1.1kVgradearmouredpowerandcontrolcablesbetwe

ensolarmodules,mainpowercabletogridsupplyPCUunitalongwithsupplying&fixi

ngofnecessarychannel/conduitlugsandotheraccessoriesetc.asrequired.

Subhead-X On Grid Solar Power Backup System 10,85,600.00 -

Grand Total (DSR+Market Based Item) 79,47,647.51

Grand Total (DSR+Market Based Item) 79,47,647.51

Grand Total (DSR+Market Based Item) In Lacs 79.48

Grand Total (DSR+Market Based Item) In Lacs 79.48

Signature of Tenderer

68 Signature of NBCC

Detailed Estimate Based On DSR-2025 With Cost Index & Market Rate

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11, TARAMANDAL, NEAR CIRCUIT HOUSE, OPP. RAMGARHTAL LAKE, GORAKHPUR (U.P.)

Name Of Work -Internal Electrical

Rate as per D.S.R. 2025 Rate as per Market Rate

Sr.No. Sch.No. Particulars Qty Unit Amount Rate Amount

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

1 1.10.3 conduit, with modular switch, modular plate, suitable GI box 185.00 Nos. 1,704.00 3,15,240.00

and earthing the point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

2 1.11 recessed medium class PVC conduit, 2 way modular switch, 4.00 Nos. 1,803.00 7,212.00

modular plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable

etc. as required. -

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single core

cable in surface/ recessed medium class PVC conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC

insulated annealed copper conductor, unarmored telephone

cable in the existing surface/ recessed steel/ PVC conduit as

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid

copper conductor PE insulated, shielded with fine tinned copper braid

and protected with PVC sheath in the existing surface/ recessed steel/

PVC conduit as required. -

Signature of Tenderer 69 Signature of NBCC

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required. -

Supplying and fixing following modular switch/ socket on the

7 1.24 existing modular plate & switch box including connections but -

excluding modular plate etc. as required. -

a 1.24.6 Telephone socket outlet 8.00 Each 168.00 1,344.00 -

b 1.24.7 TV socket outlet 5.00 Each 168.00 840.00 -

c RA-1 RJ45 socket cat 6 with shutter 78.00 Each - 421.58 32,883.09

d MR HDMI Socket 7.00 Each - 650.00 4,550.00

Supplying and fixing following size/ modules, GI box alongwith

9 1.27 modular base & cover plate for modular switches in recess etc. -

as required. -

Supplying and fixing suitable size GI box with modular plate and cover

in front on surface or in recess, including providing and fixing 3 pin 5/6

A modular socket outlet and 5/6 A modular switch, connections etc. as

Supplying and fixing suitable size GI box with modular plate and cover

in front on surface or in recess, including providing and fixing 6 pin 5/6

& 15/16 A modular socket outlet and 15/16 A modular switch,

connections etc. as required. -

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including connections

etc. as required. -

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required. -

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surface/ recessed Steel/ PVC conduit as required. -

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point ( without independent

15 1.55 switch etc.) with 1.5 sq. mm FRLS PVC insulated copper -

conductor single core cable in surface/ recessed PVC conduit,

and earthing the point with 1.5 sq. mm FRLS PVC insulated

copper conductor single core cable etc. as required. -

Supplying and fixing suitable size GI box with modular plate and cover

in front on surface or in recess, including providng and fixing 2 nos. 3

16 1.56 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, 91.00 Each 757.00 68,887.00

connections etc. as required. (For light plugs to be used in non

residential buildings). -

Signature of Tenderer 70 Signature of NBCC

Supplying & fixing suitable size GI box wih modular plate and

cover in front on surface or in recess including providing and

fixing 25 A modular socket outlet and 25 A modular SP MCB, "C"

curve including connections, painting etc. as required. -

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

18 2.3 complete with tinned copper bus bar, neutral bus bar, earth -

bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator) -

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

20 2.4 surface/ recess, complete with tinned copper bus bar, neutral -

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator) -

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve,

miniature circuit breaker suitable for inductive load of following poles

in the existing MCB DB complete with

connections, testing and commissioning etc. as required. -

c 2.10.5 Three Phase & Neutral 6.00 Each 1,301.00 7,806.00 -

Supplying and fixing 63Amp, four pole, (three phase

and neutral), 415 volts, residual current circuit breaker (RCCB),

23 RA-3 having a sensitivity current 300 mA in the existing MCB DB 2.00 Each - 4,116.94

complete with connections, testing and commissioning etc. as

required. 8,233.87

Supplying and fixing 40/63A rating, 415 V, 10 kA, "C" curve,

miniature circuit breaker suitable for inductive load of Four poles in

25 RA-4 the existing MCB DB complete with connections, testing and 5.00 Each - 1,925.19

commissioning etc. as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with

27 5.4 cover plate having locking arrangement and watering pipe of 8.00 Each 8,531.00 68,248.00

2.7 metre long etc. with charcoal/ coke and salt as required. -

Signature of Tenderer 71 Signature of NBCC

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre

below ground as strip earth electrode, including connection/

29 5.9 terminating with G.I. nut, bolt, spring, washer etc. as required. 40.00 Meter 160.00 6,400.00

(Jointing shall be done by overlapping and with 2 sets of G.I. nut

bolt & spring washer spaced at 50mm) -

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

recess for connections etc. as required. -

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

34 5.18 for loop earthing along with existing surface/ recessed conduit/ 300.00 Meter 50.00 15,000.00

submain wiring/ cable as required. -

LED Down lighter (SMD Type) (System lumen efficacy

≥120<135lm/Watt)

Supplying, installation, Testing & Commissioning of LED

Recessed/surface Down lighter (Round/ square/ Rectangular) SMD

type of following body material with PMMA and prismatic diffuser and

construction as per IS : 10322 with driver as per the requirement with

Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency

50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal

35 surge protection of 2.5 KV with Short & Open circuit protection ,THD -

< 10%, P. F.≥0.95, IP20, CRI >80, UGR (Unified GlareRating) <19,

Flicker free (flicker should be below 5%), life time (LED, Driver &

electrical circuitry), lifetime of minimum 50000 Burning Hours with

70%of initial Lumen maintained till life ends, CCT3000°K / 4000°K /

5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color

Matching) <3, Maximum power consumption should not more than the

specified rating and Fixture shall be of relevant BIS standard.

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen

printing on housing Complete in all respect i/c external connections

PVC insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy

≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing

required for LED fixtures as per BIS shall be submitted.. Shape size -

andCCT shall be as approved by Engineer-inCharge as per

requirement. (Thermal management: heat sink of aluminium housing

such that LED junction temperature shall not rise above 90°C). Powder

coated die cast /Extruded aluminium Body including trim

Signature of Tenderer 72 Signature of NBCC

LED Down lighter (SMD Type) (System lumen efficacy

≥120<135lm/Watt)

Supplying, installation, Testing & Commissioning of LED

Recessed/surface Down lighter (Round/ square/ Rectangular) SMD

type of following body material with PMMA and prismatic diffuser and

construction as per IS : 10322 with driver as per the requirement with

36 Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency -

50/60 hz, Operating temp range -5 0C to 40 0C centigrade, internal

surge protection of 2.5 KV with Short & Open circuit protection ,THD

< 10%, P. F.≥0.95, IP20, CRI >80, UGR (Unified GlareRating) <19,

Flicker free (flicker should be below 5%), life time (LED, Driver &

electrical circuitry), lifetime of minimum 50000 Burning Hours with

(As per iti l L Bin), SDCM(Standard

i t i d till lif Deviation

Color Matching) /

Maximum power consumption should not more than the specified

rating and Fixture shall be of relevant BIS standard. Manufactures

Word Mark/ Name Engraved/ Embossing/ Screen printing on housing

Complete in all respect i/c external connections with 1.5 sq mm

FRLS/HFFR, PVC insulated copper conductor single core cable and

earthing etc. as required with Minimum 5 year OEM warranty. System -

lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report

and all testing required for LED fixtures as per BIS shall be submitted..

Shape size andCCT shall be as approved by Engineer-

in_x005fCharge as per requirement. (Thermal management: heat

sink of aluminium housing such that LED junction temperature shall

not rise above 90°C). Powder coated die cast /Extruded aluminium

Signature of Tenderer 73 Signature of NBCC

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of Panel light 2x2

ft., of following body material and construction as per IS : 10322 with

driver as per the requirement with Driver efficiency >85%, Operating

voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5

0C to 40 0C, internal surge protection of 2.5 KV with Short & Open

circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80,UGR

(Unified Glare Rating) < 19, Flicker free, (flicker should be below 5

%), life time (LED, Driver & electrical circuitry), of minimum 50000

Burning Hours with , 70% of initial Lumen maintained till life ends

,CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin),

37 SDCM(Standard Deviation Colour Matching) <3, Maximum power -

consumption should not more than the specified rating and Fixture

shall be of relevant BIS standard. Manufactures Word Mark/ Name

Engraved/ Embossing/ Screen printing on housing. complete in all

respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy

>135 lm/Watt output . LM79 & LM80 Test report and all testing

required for LED fixtures as per BIS shall be submitted. Shape size and

CCT shall be as approved by Engineer-in_x005fCharge as per

requirement. (Thermal management: heat sink of aluminium housing

such that LED junction temperature shall not rise above 90°C). Powder

SITC of 12W Extruded aluminium batten available in 2ft run length

38 RA-5 with multiple lumen packages and suitable for surface, wall & conduit 18.00 Each - 430.34

ounting (with accessories). 7,746.04

Signature of Tenderer 74 Signature of NBCC

LED Batten light (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of LED surface

mounted Batten light of following body material and construction as

per IS : 10322 with driver (Replaceable) as per the requirement with

Driver efficiency >85% ,Operating voltage AC 140-270 Volt, frequency

50/60 hz, Operating temp range -5 0C to 40 0C, internal surge

protection of 2.5 KVwith Short & Open circuit protection ,THD < 10%

, P.F.≥0.95, IP20, CRI >80, Flicker free (flicker shouldbe below 5 %),

life time (LED, Driver & electrical circuitry), of minimum 50000

Burning Hours with 70% of initial Lumen maintained till life ends,

CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin),

39 SDCM(Standard Deviation Color Matching) <3, Maximum power -

consumption should not more than the specified rating and Fixture

shall be of relevant BIS standard. Manufactures Word Mark/ Name

Engraved/ Embossing/ Screen printing on housing complete in all

respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc. as

required with Minimum 5 year OEM warranty. System lumen efficacy

>135 lm/Watt output . LM79 & LM80 Test report and all testing

required for LED fixtures as per BIS shall be submitted.. Shape size

and CCT shall be as approved by Engineer-in-Charge as per

requirement. (Thermal management: heat sink of aluminium housing

such that LED junction temperature shall not rise above 90°C). Powder

Supply and fixing of water tight oblong 10 Watt LED bulkhead luminaire

having pressure diecast housing with driver set confirming to IP 65 and above

Protection, IK08, High purity / transmisivity UV stablized Non yellowish

41 MR diffuser/ Reflector for uniform light distribution, ditachable driver set, suitable 8.00 Each -

for 24hrs continuous operation complete in all respect.

1200 system lumen, >120lm/W, PF>0.95, CRI>70, >300V, over voltage

protection 4KV internal surge protection with 5 year warrenty CAT-AAA

Supply and fixing hexagonal Round G.P.fan box approved make made

up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight

DSR Civil holes for pipe entry of the box. Holes should be semi-shuttered type

2023 10.18 with 0.5 mm G.P. Sheet made upper & lower cover duly screwed.

Fixing with wiring conduit laid in the R.C.C. roof before concreting

alongwith supply of all material, labour, T&P etc. required for proper

completion of the work -

Supply Installation Testing and Commissioning of 400mm sweep

46 RA-2 1500RPM energy efficient BLDC fan with double ball bearing for 7.00 Each - 5,348.85

longer life. 37,441.94

Lightning Arrestor Work - -

Signature of Tenderer 75 Signature of NBCC

Lightning Arrestor: Supply, installation, testing and commissioning of

External Lightning wide area protection system based on Eaarly

Streamer Emission (ESE) technology. Device shall emit

electromagnetic impulse in the form of a streamer into the air

47 MR microseconds earlier than naturally formed streamers. Device confirmg 1.00 Each - 1,52,800.00

to NFC 17-102 and UNE 21186 Standards. Appropriate non

penetrating mounting arrangement. The device shall be mounted at

suitable clear to the highest point on the roof top. (Model selected shall

give coverage of 79 M radius @ min 5M height from terrace) 1,52,800.00

Down conductor:Supply, installation, testing and commissioning of 70

48 MR Sqmm twisted 19-Strand, bare Cu cable on surface/wall / as per site 50.00 Metre - 2,127.90

requirement and complete in all respect. 1,06,395.00

Lightning Counter :Supply and installation of counting the number of

lightning strikes without any power supply. 9,000.00

Earthing with copper earth plate 600 mm X 600 mm X 3 mm

thick including accessories, and providing masonry enclosure

with cover plate having locking arrangement and watering pipe

of 2.7 metre long etc. with charcoal/ coke and salt as required. -

Test Link :Supply and installation of test link in weather proof IP 65

Supply, installation, testing and commisioning of 2 x 25W LED

Aviation abstruction light medium bay type 62, complete with lamp,

lamp holder, Condenser necessary connecting wire, 1 X 25 AV with all

necessary hardware, accessories as required for complete installation.

Rate shall include the cost of necessary steel structures , fixing

arrangements in this item. Refer drawing. 10,406.00

Online UPS- Input supply: Three Phase, Output supply: Three

Supplying, installation, Testing & Commissioning of of following

capacity at full load (Unity Power Factor) at operating temperature 0 to

Relative humidity 0 to 95%, Online double conversion true sine wave

Uninterrupted hot swappable (allow for the replacement or addition of

battery modules without shutting down the entire system) modular

Supply (UPS) system with N+1 modules (N denotes total number of

moduels requird for rated capacity). The UPS shall include a Rectifier,

inverter, battery bank suitable for 30 minutes back up (Battery VAH

capacity shall not be less than 1600 VAH per KVA of UPS rating per

Hour backup time) on full load (Battery shall be VRLA, SMF in ABS

Container) and Static Bypass switch alongwith provision for manual

bypass, suitable isolation transformer for additional protection against

lf l UPS h ll h i b il

Signature of Tenderer 76 Signature of NBCC

phase sequence correction. The UPS systems offered are to be of the

technology with Digital Control Microprocessor based for reliable

operation using Insulated Gate Bipolar Transistor (IGBT)'s both for the

rectifier & inverter (3 Level) with PWM (Pulse Width Modulation).

The quality of design, manufacturing and inspection process should -

confirm to the relevant International standards such as IEC/EN/VDE.

The operating efficiency of the UPS systems shall be >96% while

operating on battery mode and delivering quality power to the 100%

non-linear loads. Current total harmonic effect(ITHD) on the input grid

shall be < 5% at 50 %load (The required LC (

inductor (L) and a capacitor (C)) filters shall be included in UPS cost),

extreme power factor kit to be included to limit the input power factor

(PF) to 0.99 and output power factor shall be unity (i.e. kw rating of

the UPS shall be kva rating x 1 ), however UPS shall be suitable to

take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be

suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5

Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload

capacity of 120% for 10 mins, Sine wave output. Non condensing, -

noise level less than 60db at 1 meter distance, protections: Input Under

voltage over voltage, abnormal out voltage, battery over charging,

output over current, short circuit protection, battery deep discharge

protection, 10KV surge. UPS must comply with low voltage

electromagnetic compatibility (EMC) achieved as per EN 6204,

EN6204 Part I and Part 2, it shall be a Voltage and Frequency

Independent (VFI)-type UPS. Communication RS232/RS485/SNMP

integration, t hardware

all l f BMS& software for iOT Communication as per

approved by Engineering in charge. Required battery racks and

interconnecting copper conductor cables of suitable size and connectors

and all required accoseries are inclusive of the cost). This system must

provide a means for logging and alarming of all monitored points plus

email notification. Forced air-cooling with integral inbuilt fans with

redundancy (if one fan fail UPS should be able to handle at least 80% -

of the load, Noise Level 65 DB at 1 meter distance. The system shall

be in compliance IEC 62040- 1,2 & 3, IS: 16242 and CPWD

Specification. Display Panel (minimum) (In-build 5 inch or more LC

Display / LED ) to display : a) Input: Voltage, current, Frequency. b)

Bypass: Voltage, Frequency. c) Output: Voltage, frequency, Current.

Signature of Tenderer 77 Signature of NBCC

d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage.

f)Temperature: STS, Inverter, PFC. g) Event Logging & Statistical

LCD/LED): UPS should capture and display up to 3000 events like:

temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-

26.2 Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) -

Statistical Data: No. of power failures / Transfers to Bypass / Total

Running time, etc. i) Mains Mode of Operation /Battery Mode of

Operation / Bypass feeding the load /UPS Fault /Battery charging and

discharging, overload, battery voltage and battery capacity. j) Audible

Alarms : Mains Failure, Battery Low Alarm, UPS Overload, Fault,

Shutdown, Input Over, Under Voltage, Output Over, Under Voltage,

Battery Over, Under Voltage, Over Load and short circuit, Over

a 26.2.3 30KVA (Each Power module shall be < 10 KVA) 1.00 Set 5,05,748.00 5,05,748.00 -

Grand Total (DSR+MARKET BASED ITEM) 51,69,021.18

Grand Total (DSR+MARKET BASED ITEM) 51,69,021.18

Grand Total (DSR+MARKET BASED ITEM) In Lac 51.69

Grand Total (DSR+MARKET BASED ITEM) In Lac 51.69

Signature of Tenderer 78 Signature of NBCC

Detailed Estimate Based On DSR-2025 With Cost Index & Market Rate

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11, TARAMANDAL, NEAR CIRCUIT HOUSE, OPP. RAMGARHTAL LAKE,

GORAKHPUR (U.P.)

Name Of Work - Fire Detection Alarm & PA System Work

Rate as per D.S.R. 2025 MARKET BASED

Sr.No. Sch.No. Particulars Qty Unit Amount Rate Amount

Fire Alarm System :

Supplying, installation, testing and commissioning of micro

processor based intelligent addressable main fire alarm panel,

central processing unit with the following loop modules and

capable of supporting not less than 240 devices (including

detectors) and minimum 120 detectors per loop and loop

length up to 2 km, network communication card, minimum

320 character graphics/ LCD display with touch screen or

other keypad and minimum 4000 events history log in the non

1 28.2.1 volatile memory (EPROM), power supply unit (230 ± 5% V,

50 hz), 48 hrs back-up with 24 volt sealed maintenance free

batteries with automatic charger. The panel shall have facility

to connect printer to printout log and facility to have seamless

integration with analog/digital voice evacuation system (which

is part of the schedule of work under SH: PA System) and

shall be complete with all accessories . The panel shall be

compatible for IBMS system with open protocol BACnet/

Modbus over IP complete as per specifications.

Supplying, installation, testing & commissioning of

2 28.2.4 intelligent analog addressable photothermal (Smoke) detector 48 NOS 3,004.00 1,44,192.00 -

complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response

3 28.2.5 indicator on surface/recessed MS Box having two LED, 40 NOS 306.00 12,240.00 -

metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of fault

isolator complete with base as required.

Signature of Tenderer 79 Signature of NBCC

Supplying, installation, testing & commissioning of intelligent

5 28.2.9 addressable thermal detector with rate of rise cum fixed 20 NOS 2,866.00 57,320.00 -

tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of

addressable fire control module complete as required.

Supplying, installation, testing & commissioning of

addressable phone control module complete as required.

Supplying, installation, testing & commissioning of

addressable manual call point complete as required.

Supplying, installation, testing & commissioning of

addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of fire fighter

telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter

phone jack complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured

cable, 600/1000V rated with annealed copper conductor

having glass mica fire barrier tape covered by an extruded

layer of Cross Linkable Ethylene Propylene Rubber (EPR)

insulation and LSZH inner bedding, steel wire armouring &

LSZH outer sheath complete as required.

Public Address System : -

Supplying, installation, testing & commissioning of 6 zone,

voice alarm controller with USB, MP3 player (including 6

13 28.3.1 zone button paging station) with seamless integration facility 1 each 1,32,115.00 1,32,115.00 -

with main fire alarm panel for voice evacuation complete as

Supplying, installation, testing & commissioning of 1.5/3/6W

ceiling speaker complete as required.

Signature of Tenderer 80 Signature of NBCC

Supplying, installation, testing & commissioning of digital

15 MR audio amplifier 500 Watt, 25V rms operating at 240 Volt AC 1 each 45,000.00 45,000.00

Supply complete as required.

Supplying, installation, testing & commissioning of Voice

16 28.3.9 command keypad 6 zone, with microphone assembly complete 1 each 85,450.00 85,450.00 -

Supplying and drawing of cable Fire Retardant PVC insulated

copper conductor cable in the existing surface / recessed steel

conduit of following pairs, cores and size including

connections and interconnections etc. as required.

a 28.5.3.1 17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm 507 metre 61.00 30,927.00 -

18 1.21.2 Same as in item 148, but 25mm dia PVC conduit. 507 Meter 168.00 85,176.00 -

GRAND TOTAL (DSR+MARKET BASED ITEM) 11,42,647.00

GRAND TOTAL (DSR+MARKET BASED ITEM) 11,42,647.00

GRAND TOTAL (DSR+MARKET BASED ITEM) IN LAC 11.43

GRAND TOTAL (DSR+MARKET BASED ITEM) IN LAC 11.43

Signature of Tenderer 81 Signature of NBCC

Detailed Estimate Based On DSR-2025 With Cost Index & Market Rate

ICAI BHAWAN- GORAKHPUR SITUATED AT PLOT NO-B-11, TARAMANDAL, NEAR CIRCUIT HOUSE, OPP. RAMGARHTAL LAKE, GORAKHPUR

Name Of Work - Lift Work

Rate as per DSR 2025 MARKET BASED

Sr.N Rate as per

Sch.No. Particulars Qty Unit Amount Rate Amount

Supplying, Installation, Testing & Commissioning of

following capacity passenger Machine room less (MRL)

lift with regenerative drive as per CPWD General

Specification for Electrical Works (Part-III Lift &

Escalator) 2003, BIS Codes, NBC 2016 as amended upto

1 21.1 date, having provision for barrier free access as per

Harmonised Guidelines & Standards for Universal

Accessibility in India – 2021 of MoHUA, serving

different floors in the lift shaft as per detailed

specifications enclosed and as under including all other