8701 SPECIAL REPAIRS TO BLDG No. P 02 AT AF STATION, BAREILLY

Amount

Removal to existing treatment from roof including brick tiles laid dry etc any thickness or description complete all as specified .

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed.

M&L for providing cement concrete type B0, 1:2:4 using 12.5mm graded aggregate as in leveling course on roof complete including necessary formwork all as specified.

M&L for providing 90-100 micron thick polymeric water proofing membrane over leveling coarse on approachable roof with following Specifications : 1. Average 10mm thick plaster in CM 1:3 mixed with polymer based water proofing compound when leveling coarse is still green. 2. After the surface is fully dried, apply a coat of bituminous primer @ 0.30 liters/Sq.m. 3. After primer, the entire roof surface shall be applied with hot, blown bitumen grade 85/25 confirming to IS-702 @ 1.2 Kg/Sq.m 4. Over hot bitumen, polymeric water proofing membrane consisting of 90 to 100 micron thick central core of HMHDPE film and standard weight 3 Kg/Sq.m shall be laid with 100mm side lap/end lap on prepared surfaces as per manufacture’s instruction. 5. Laying brick tiles laid over a bedding layer of 20mm screed in CM 1:4 mixed with polymer based liquid water proof additive @ 5% by weight of cement or as per manufacturer’s instructions and tiles joints shall be filled with polymer based cement proof joint filler of approved make complete all as specified and directed.

M&L for cutting out crack in V section in existing roof, chajjas or similar work up to 40mm deep and cleaning the same with water jet to get rid of any loose material and wetting, grouting with cement & sand mortar 1:3 mixed with liquid WPC all as directed.

M&L for providing cement concrete type B1, 1:2:4 using 20mm graded aggregate as in lintels up to 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, copings, bed plates etc complete including necessary formwork all as specified.

Demolition of cement concrete (un reinforced) of any description and in any position not otherwise specifically provided for all as specified and as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles all as directed.

M&L for brick work with fly ash bricks straight or curved on plan exc. 6m mean radius using old size bricks built in cement mortar (1:6) all as specified.

Taking up or down galvanized steel tubing 15mm bore with fittings.

Taking up or down galvanized steel tubing 20mm bore with fittings.

S&F GI tubes 15mm bore dia medium grade galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors complete including cutting chases for concealing the pipes and making good the disturbed surfaces all as specified and as directed.

S&F GI tubes 20mm bore dia medium grade galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors complete including cutting chases for concealing the pipes and making good the disturbed surfaces all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks, double layered of capacity 500 ltrs (cylindrical vertical with closed top) hoisted and fixed in position complete including necessary GI tank nipples, taking down existing unserviceable tank all as specified and as directed by Engineer-in-charge.

S&F in repairs Ball valves 20mm bore dia, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed [Minimum weight: 210gms] all as specified including taking down existing unserviceable valve.

S&F in repairs PVC (SWR) pipe 110mm bore, single socketed in any length with rubber ring joints fixed to walls complete all as directed.

S&F PVC (SWR) bends 110mm bore, any radius complete all as directed.

S&F Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) with dia of outlet 75mm complete all as specified.

S&F Cast iron soil, waste and vent pipes 75mm bore, sand cast in any length with or without ears, with cement joints, laid in trenches or in floors all as specified.

S&F Cast iron soil, waste and vent pipes 100mm bore, sand cast in any length with or without ears, with cement joints, fixed to walls all as specified.

S&F of 100mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) complete all as specified and directed.

S&F of 75mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) complete all as specified and directed.

S&F cast iron cowl 75mm

S&F 100mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed.

S&F Stack clamps for 75mm bore pipe out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified.

S&F Stack clamps for 100mm bore pipe out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified.

Dismantling of cast iron or reinforced concrete drain pipes 75/ 100mm dia, jointed in cement mortar and taking out of trenches, if required

S&F in repairs vitreous china ware wash down water closet pan (pedestal pattern) white including PVC seat cover with mild steel chromium plated or aluminised hinging device, fixing bolts jointing to flushing cistern and flush pipe anti syphonage pipe etc complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc. 15cm thickness (below or above ground level) all as specified and as directed.

M&L for 75mm thick cement concrete type C1, 1:3:6 (using 40mm graded stone aggregate) in plinth protection, laid in bay n.exc. 3.00 sq.m each, finished even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight) complete all as specified and directed.

S&F in repair vitreous china white flat back wash hand basin 550 x 400mm size including CP waste coupling, 32mm dia PVC waste pipe, CI/MS brackets including cutting for and pinning in brackets or fixed with brass screws all as directed.

S&F in repairs PVC valve less, syphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle, brackets complete including PVC connection and outlet pipe all as directed. [Make: 'Slim line' of M/s Parry ware/ 'Champion' of M/s Hindustan Sanitary ware/ 'Sleek+' of M/s Hindware]

S&F in repairs Stop valves/ Angle valves, 15mm bore, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as specified and as directed

S&F PVC connection 15mm size 450mm long with PTMT nuts on both sides.

S&F in repairs basin mixer cast copper alloy, chromium plated with central hole for WHB, fancy type 15mm bore with 450mm long braided hose complete all as directed. [Cat No. CON-167KNB of make: Jaquar or equivalent in Kajaria/ Cera]

S&F in repairs Bib taps, 15mm bore, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F corner shelf, fancy type three tier with 5.50mm thick glass mounted on CP brass frame fixed with brass screw & plug, size not less than 450mm complete all as specified. [Make: Jaguar/ Marc/ Plumber]

S&F in repairs brass chromium plated grating doom 100 mm dia complete all as directed.

S&F in repairs brass chromium plated Towel rail 'D' type, 600mm long complete all as specified and directed. [Make: Jaquar/ Marc/ Plumber]

S&F in repair brass chromium plated Soap dish complete all as directed. [Make: Jaquar/ Marc/ Plumber]

S&F in repairs 20mm bore gun metal globe or gate valve with iron wheel heads Class-II, screwed both ends for iron pipe all as specified.

Taking down cement plaster on brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc. to receive plaster

M&L for rendering 15mm thick in CM (1:4) on brick or concrete surfaces finishing even and smooth without using extra cement complete including mixing water proofing compound all as specified. [Note: Supply only water proofing compound shall be measured and paid separately]

M&L for rendering 15mm thick in CM (1:6) on brick or concrete surfaces, finishing even and smooth without using extra cement complete all as specified.

Supply only liquid water proofing compound. [Make: Conplast X421 IC of make: M/s Fosroc Chemicals India (P) Ltd. or equivalent in M/s Pidilite Industries Ltd./ M/s Sika India Pvt. Ltd./ M/s Structural Water Proofing Co. Pvt. Ltd./ M/s BASF India Ltd.]

M&L for rendering 10mm thick in CM 1:3 on surfaces of ceiling finished even and smooth without using extra cement complete including brushing neat cement slurry with 3 kg of cement per sq.m. preparatory to rendering complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying white cement based putty for 1.5 to 2mm thick, sand papering to obtain smooth and even finish and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as directed.

M&L for preparation of new plastered surfaces of walls and applying white cement based putty for 1.5 to 2mm thick, sand papering to obtain smooth and even finish and applying two coats of exterior acrylic emulsion over a coat of exterior primer complete all as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified.

Taking down chowkats or frames with shutters (with out taking off shutters from frames) n. exc. 1.5sq.m. each all as specified.

Taking down chowkats or frames with shutters (with out taking off shutters from frames) exc. 1.5sq.m. but n. exc. 4sq.m. each all as specified.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, supplying & fixing in opening as per specification & drawing shown on Sl. Page No. 180 of SSR Part-II-2020.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing shown on Sl. Page No. 176 of SSR Part-II-2020.

S&F powder coated aluminium (minimum thickness of powder coating 50 microns) work for doors, windows, ventilators and partitions (fixed portion) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. complete all as specified and as directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 microns) door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified and as directed. [Note: 1. Weight of builders hardware & rubber beading shall not be considered for payment, however rate quoted shall be deemed to be included for the same. 2. Panel inserts like glass, prelaminated particle board & gauge shall be measured & paid separately]

S&F powder coated aluminium (minimum thickness of powder coating 50 microns) sliding type three track (02 glazed shutters and 01 gauzed shutter) window with sliding shutter and frame with and including aluminium grill, 5 mm thick tinted glass and mosquito proofing net as detailed below complete all as specified and directed: - (i) Frame section 91.85 X 31.75 X 1.30 mm, section No. 8758 for top and sides rails and 91.85 X 31.75 X 1.20 mm for bottom rail, section No. 8687. (ii) Shutter for top, bottom and side rails 40 X 18 X 1.50 mm, section No. 8820. (iii) Glass 5.00 mm thick one side reflective glass and other side visible fixed with rubber gasket and aluminium clips bearing section No. 4407 and necessary handles, tower bolt etc. as directed. (iv) Stainless steel wire cloth (v) Filling of gap between wall and aluminium frame with silicon putty to make it proper water tight. (vi) Locking arrangement and providing Namda rope to make the frames air tight.

S&F powder coated aluminium (minimum thickness of powder coating 50 microns) grill of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

S&F 5.50 mm thick sheet glass (tinted/ reflective type) of any size complete fixed to aluminium frames

S&F 12mm thick prelaminated particle board, interior grade, prelaminated on both sides with decorative choice lamination, fixed with screws to timber frame work all as specified.

S&F 100mm long Butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodized and fixed, type C-21 all as specified.

S&F extruded aluminium handle 150mm long fabricated type anodized all as specified.

S&F standard EPDM rubber beading for fixing of glass partition

S&F Veneered particle boards interior grade 18/19mm thick, solid core, faced with decorative veneer on both faces general purpose type, with face veneers of type 'BB', fixed with screws to timber frame work

M&L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, cross sectional area exc. 13sq.cm but n.exc. 25sq.cm, clean sawn, secured with nails or brads to timber frame all as specified.

S&F Teak wood beading 18/19mm X 4mm fixed with headless nails complete all as specified and as directed

S&F 40mm dia cupboard knobs fixed with nut, screw and washer of mild steel, bright finished

S&F Continuous (piano) hinges, mild steel, bright finish or electro-galvanised, width of flaps (when open) in 40mm complete.

S&F 75mm Extruded brass handles, fabricated type polished

S&F Full extension drawer slider 450mm with plastic rollers, width 12.5mm complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F 125mm Extruded aluminium alloy handles, fabricated type, anodized

S&F 150mm long aluminium, anodized, barrel tower bolts of extruded section and fixed complete all as specified and directed

M&L 140mm length of Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for 25mm thick cement concrete PCC 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for flooring all as specified

M&L for glazed digitally printed ceramic tiles of size 300x450mm, 6 to 7mm thick in vertical surfaces of wall, set and jointed in neat cement slurry and pointed in coloured cement to match laid over and including 10mm thick backing coat in CM 1:4 complete all as specified.

M&L for non skid coloured ceramic joint free tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.11sq.m but n.exc. 0.18sq.m, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match laid over and including 15mm thick screed bed in CM (1:6) complete all as specified.

M&L for double charged, vitrified tiles, coloured, first quality of size 600x600mm, 9 to 10mm thick as in Floors/ skirting, set and jointed in cement slurry, finished with flush pointing in coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:6 complete all as specified and as directed. [Note: The colour / shade / design of tiles shall be as approved by GE.]

S&F in repairs fancy type Stainless steel medium grade curtain rods 20mm dia of AISI 304 Gde including suitable brackets, globes and rings @ 10 Nos per metre complete all as specified and as directed by Engineer-in-Charge.

S&F high strength deformed TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia all as specified and as directed.

S&F high strength deformed TMT steel bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia all as specified and as directed.

Use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surface of concrete all as specified

M&L for reinforced cement concrete 1:1½:3 type A1 (using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like concrete all as specified.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets and frame work.

M & L for providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of size 595x595mm of approved texture, design and pattern having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225: 1987, Light reflectance of 85% (minimum). Non combustible as pe BS:476 (Part-4), fire performance as per BS:476 (Part 6&7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518 : 1991, in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanized @ 120 grams per sq.m including both sides) comprising of main T runners of size 24x32mm of length 1200mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x600 mm susupended from ceiling using galvanised mild steel items (galvanizing @ 80grams per sq.m) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level aduster of size 85x25x25x2mm. Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450mm c/c and 40mm long dry wall/ partition with the help of plastic rawl plugs at 450 mm c/c and 40mm long dry wall S screws. The work shall be carried out as per specifications, drawing and as per directions of Engineer-in-Charge.

Taking down carefully aluminium/ copper point wiring for light, fan, socket or power point etc. complete with all fittings and fixtures such as switch piano, ceiling rose, switch socket, pendants etc including making good surface of wall, ceiling etc complete all as specified.

Taking down carefully existing sub-main wiring of any description complete all as specified.

Taking down distribution board of any type including cutout, MCBs etc.complete all as specified and as directed.

M&L for Point wiring complete as specified with 1100 volt grade 1.5sq.mm. (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade (IS:694) drawn through and including rigid non-metallic PVC conduit of suitable size not less than 20mm dia, with all fittings, concealed in wall/ roof / floor including pressed steel concealed terminal boxes of required size with top cover of 3 mm thick of plastic laminated sheet of required colour suitable for housing switches/ sockets/ regulators etc. duly earthed with same cable as for wiring above but green in colour as continuous earthing wire complete all as specified for one light/ fan/ bell point controlled by one switch 6 Amps 1 way. [Note:- M&L for cutting chases for concealed conduit wiring on any surfaces and making good disturbed surfaces to match with the existing surfaces in cement mortar 1:3 and finishing with existing finishes shall be deemed to be included in the quoted rate.]

All as per Item No. 92 herein before but for one 3 pin 6 Amp socket out let point on independent board.

All as per Item No. 92 herein before but for one 3 pin 6 Amp socket out let point on same board with other switches.

All as per item No. 92 herein before but point wiring with 1100 volt grade 2.5sq.mm. (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade (IS:694) duly earthed with same cable as for wiring above but green in colour as continuous earthing wire suitable for one 3 pin 16 Amps socket out let on independent board.

S&F switch piano, flush type SP, one way 5/6 Amps, 230V AC

S&F switch piano, flush type, SP, one way, 15/ 16 Amps, 250 V, ISI marked.

S&F socket outlet 6 Amp, 2 in 1, 5 pin, 230V AC

S&F socket outlet 6/16 Amp, 2 in 1, 6 pin, 230 V AC

S&F ceiling rose PVC/ Poly carbonate isolated body, three terminal complete all as specified.

S&F electronic fan speed regulator, suitable for single phase AC 240 volts, 50 Hz, 100 watts complete all as specified and as directed by Engineer-in-Charge.

M&L for sub main wiring concealed complete with two runs of 1100 Volts grade 4 sq.mm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade drawn through and including 25mm dia non metallic rigid PVC conduit and conduit accessories concealed in walls/ roofs/ floors etc. with one run of 1100 Volts grade 4 sq.mm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade as earth continuity conductor all as specified. [Note:- M&L for cutting chases for concealed conduit wiring on any surfaces and making good disturbed surfaces to match with the existing surfaces in cement mortar 1:3 and finishing with existing finishes shall be deemed to be included in the quoted rate.]

M&L for sub main wiring concealed complete with two runs of 1100 Volts grade 6 sq.mm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade drawn through and including 25mm dia non metallic rigid PVC conduit and conduit accessories concealed in walls/ roofs/ floors etc. with one run of 1100 Volts grade 6 sq.mm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade as earth continuity conductor all as specified. [Note:- M&L for cutting chases for concealed conduit wiring on any surfaces and making good disturbed surfaces to match with the existing surfaces in cement mortar 1:3 and finishing with existing finishes shall be deemed to be included in the quoted rate.]

S&F recess mounted direct lighting LED Luminaire 34-36W of size 2'x2', with powder coated CRCA housing, seamless front frame, flat white high transmission acrylic cover fixed to Modular/ Gypsum/ POP ceiling complete including connecting up with three core twisted flexible copper conductor cable of suitable size from ceiling rose to fitting all as directed including taking down existing unserviceable light fitting. [Cat No. PLUTONEO2X2PLR34WLED857S of make: Havells or Cat No. RC380B LED36S-6500 G5 L60W60 PSU OD of make: Philips or Cat No. LCTLRNE-36-FO-CDL of make: CG/ Cat No. CRCO10S038HP57GL of make Wipro with frame of Cat No. 9180P01089 LP]

S&F Wall/surface mounted type LED light fitting batten type complete with LED 1x 20 watt (4 feet long), extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with 3 core twisted flexible copper conductor cable complete all as specified and as directed. Make :- Philips Cat Part No : BN100C LED20S-6500 PSU L120 GR S4, Havells Cat Part No : STOUT PLUS 600BS 20W LED 857SPCWH, Wipro Cat Part No : Wipro Garnet 20W LED Batten (White) D532065

M&L for Angle Holder, insulated body with back plate with & including LED Lamp 12 Watt suitable for batten fittings complete all as specified and directed by Engr-in-Charge.

S&F Ceiling fan complete with blades, white colour, with down rod, including all accessories, 230 V, 1200 mm sweep, minimum air delivery 210 CFM with service value 6.00, BEE 5 star rated with brushless direct current motor (BLDC) complete including taking down old u/s fan all as specified and as directed. Make :- Usha Model No: Usha Energia 32 1200mm, Havells Model No: Havells Efficiencia Neo 1200mm, Orient Model No: Orient Electric I Tome Plus 1200mm [Note: Old Ceiling fan shall be deposited in MES Store Yard]

S&F Wall mounted fan 400mm sweep, 230V, AC with built-in regulator and swing function including electric connection from ceiling rose to fan connector with PVC insulated 2 core copper cable of size 0.75 sq.mm complete including taking down existing fan and handing over to AGE E/M Store all as directed. [Model. 'Swing' of make: Havells or equivalent in Almonard/ Bajaj/ Crompton]

S&F Exhaust fan 300mm sweep, single phase 230V, AC metal body with louvers including electric connection from ceiling rose to fan connector with PVC insulated 3 core copper cable of size 0.75 sq.mm complete including taking down existing exhaust fan and handing over to AGE E/M Store all as directed. [Make: Model No. 'Ventil Air - DB' of make: Havells or equivalent in Almonard/ Bajaj/ Crompton]

S&F sheet steel powder coated distribution board Vertical type TPN 4 ways, 415 volts, with 200 Amps rated bus bar, neutral link, earth bar, IP 43 protection and double door (Metal), suitable for mounting MCCB as incomer and MCBs as out going all as specified and as directed. [Cat No. 5077 45 DBVTH004DD of Make: Legrand or equivalent in L&T/ Havells]

S&F MCCB 4 Pole, 63 Amps, 16 kA, 415 volts with thermal magnetic release, connecting up with necessary spreader links complete all as directed. [Make: Legrand/ L&T/ Havells]

S&F sheet steel powder coated distribution board SPN 8 ways, 240 volts, with 200 Amps rated bus bar, neutral link, earth bar, IP 43 protection and double door, IK-09 with metal door suitable for mounting MCBs all as specified and as directed.

S&F MCB SPN, 240 volts, 40 to 63 Amps, C curve 10 KA all as specified and as directed.

S&F MCB SP, 6 to 32 Amps, 230 V, C curve, 10 KA all as specified and as directed.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of earth plate not less than 1.5m below normal ground level, connected to 4mm dia GI earth continuity wire by means of bolts, nuts, check nuts and washers of galvanized iron or steel and connected from earth plate electrode to main switch board/ earthing test point including watering arrangement with PCC 1:3:6 type C1 chamber, MS funnel, wire gauge, 50mm thick precast RCC cover in Type B1, including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to a distance n.exc 50m, charcoal and salt complete all as shown in electrical plate No. 3 of Schedule Part-I 2009 and connected to earthing test point all as specified or indicated and testing on completion.

Excavating manually in trenches n. exc. 1.5m wide and n. exc. 1.5m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n. exc. 10sq.m. on plan and n. exc. 1.5m in depth and getting out in soft/ loose soil.

Returning, filling in including spreading leveling watering and well ramming in layers not exc. 25cm in any type of soil.

Removing excavated materials to a distance not exc. 50m and depositing where directed at a level n.exc 1.50m above the starting point.

Supply and spread river sand as in cushioning for UG cable all as specified in clause 19.75 of SSR Part I. [Note: Punned down thickness shall be considered for payment]

M&L for well burnt Sub class 'B', modular bricks laid dry, flat, over the cable abutting each other, complete all as specified and directed.

Making horizontal bore hole under the road suitable for drawing 50mm bore pipe at a depth not less than 1 Mtr below ground level for passing of LT underground cable complete all as specfied and as directed.

Supply and laying GI pipe of 50mm bore dia light grade for cable protection, laid in trenches for drawing cables complete all as specified and as directed . [Make: Tata/ Jindal/ Zenith]

Supply, lay, connect, test and commissioning of LT XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) with aluminium conductor 1100 volts grade of size 4 Core 25 Sq.mm complete including taking up existing unserviceable cable all as specified and directed. Note: (i) Contractor shall bring the entire cable in one length. (ii) Necessary test results like continuity test, megger tests shall be submitted to Engineer-in-Charge before the cable is laid. (iii) Excavation & earth work will be measured and paid separately.

S.K.Enterprises

ZAIGHAM ENTERPRISES

MOHINDER SINGH AND SONS

VINOD TRADING CORPORATION

JAI SRI RAM ASSOCIATE

M/s M Aali construction co