WELCOME MAINT, DAY TO DAY MAINT AND REPAIR TO JOINERY, PLUMBING, SANITARY, ROOF, PLASTERING, CERTAIN E/M WORKS AND OTHER CONNECTED BLDG REPAIR WORKS IN MD OFFRS-I ACCN AND OTHER AREA OF AGE B/R-I UNDER GE (NORTH) AMBAL

Amount

Schedule 'B' Part-I (itmes) M & L taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge.

M&L rendering 10 mm thick on fair faces of brick work or concrete ceiling or chajjas surfaces in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:4 and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rough cast plaster 15 mm thick in cement motar 1 :3 complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:3 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new plastered/ unplastered surfaces of brick/concrete ceiling and applying three coats of white lime wash complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of newly plastered surfaces of wall and applying two coats of acrylic distemper using painting roller over and including 2 to 3mm thick wall care putty white cement based in two or more coats to achive smooth surface complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of newly plastered surfaces of wall and applying two coats of cement based paint complete all as specified and as directed by the Engineer-in-Charge.

M & L complete removal of existing treatment on wall by scrappers or any other means and washing , rubbing down and stopping and applying two coats of Acrylic (oil bound) distemper using painting roller over and including 2mm thick wall care putty white cement based in two or more coats to achive smooth surface complete all as specified and as directed by the Engineer-in-Charge.

M & L complete removal of existing treatment on wall by scrappers or any other means and washing , rubbing down and stopping and applying two coats of acrylic distemper using painting roller complete all as specified and as directed by the Engineer-in-Charge.

M & L complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, wasing down with water to remove loose particles etc and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including one mm thick wall care putty white cement based in two or more coats to achive smooth surface complete all as specified and as directed by the Engineer-in-Charge.

M & L complete removal of existing treatment on wall by scrappers or any other means and washing , rubbing down and stopping and applying two coats of cement base paint complete all as specified and as directed by the Engineer-in-Charge.

M&L preparing old decorated plastered wall surfaces and applying one coat of cement base paint on surfaces of walls complete all as specified and as directed by the Engineer-in-Charge.

M&L preparing old decorated plastered wall surfaces and applying two coats of white lime wash on surfaces of walls complete all as specified and as directed by the Engineer-in-Charge.

M&L preparing old decorated plastered ceiling surfaces and applying two coats of white lime wash on surfaces of ceiling complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old steel and iron surfaces of any description, not otherwise dscribed, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old steel and iron surfaces of any description, not otherwise dscribed, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old wooden surfaces of any description, not otherwise dscribed, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

M & L preparation of old wooden surfaces of any description, not otherwise dscribed, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Taking down eaves gutters, rainwater pipes and sewage/plumbing pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified & directed by the Engr-in-Charge.

S&F as in repair grating doom 100mm dia of PTMT (min weight 25gms) complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair mild steel PVC coated of approved quality curtain rod 25mm dia having wall thickness 1.60 mm with and including decorative brackets ,stop roller at the end etc, fixed with stainless steel screws complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair stainless steel of approved quality curtain rod 25mm dia having wall thickness 1.60 mm with and including decorative stainless steel brackets ,stop roller at the end etc, fixed with stainless steel screws complete all as specified and as directed by the Engineer-in-Charge.

S&F bib taps 15mm bore fancy type brass chromium plated with long body screwed down, screwed for iron pipe and fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair brass chromium plated wall/sink mixer for mixing hot & cold water for 15mm bore pipes including all connecting fittings, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair brass chromium palted WHB mixer for mixing hot & cold water for 15mm bore pipes including all connecting fittings, screwed down for iron pipe and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

M & L 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 15mm bore cast copper alloy fancy type chromium plated stop valves screwed down, high pressure with crutch or butterfly handle, scrwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge.

S & F 15mm bore cast copper alloy fancy type chromium plated stop valves with long shank and cup (concealed type), screwed down, high pressure with butterfly handle, scrwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china wash hand basin white, flat back of size 550mmx400mm with pedestal fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china squatting pan, Orissa pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device and brass chromium plated Jet spray with PVC pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets, of approved make including all connections & flush pipes for WC as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F brass chromium plated toilet paper holder complete fixed to wall as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F brass chromium plated shower rose 100mm size with or without swivel joint with arm of standard size as per site as in repair complete all as specified and as direced by the Engineer-in-charge.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 mm wide with chromiun plated brackets guard and railing 60 cm long as in reapir complete all as specified and as direced by the Engineer-in-charge.

S&F as in repair brass chromium plated jet sprey (fusset) including PVC pipe of standard length for EWC complete all as specified and as direced by the Engineer-in-charge.

S & F sinks with drainage board made out of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, waste pipe, brass chromium plated coupling and wastes; in-cluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connect-ing union to pipe overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F brass chromium plated corner glass self (set of three) with bracket as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device complete all as specified and as directed by the Engineer-in-Charge.

S&F kitchen plate rack of stainless steel sheet 1mm thickness of size 900mm x 900mm x250mm and fixed with stainless steel screws as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F cabinet type looking mirror size 450 mm x 600 mm box type including all as necessary items as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F 32 mm dia PVC waste pipe for wash hand basin / Kitchen sink etc of standard length complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair heatlh faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S & F 500 Litres rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) 100% UA stablised, rust proof, hoisted and fixed in position all as specified in SSR Part-I complete all as specified and as directed by the Engineer-in-Charge. Note:- Tank shall be in white colour.

S & F 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) tripple layer body, 100% UA stablised, rust proof, hoisted and fixed in position all as specified in SSR Part-I, complete all as specified and as directed by the Engineer-in-Charge. Note : Water storage tank shall be White in colour.

S & F 20 mm dia ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls as in repair complete all as specified and as directed by the Engineer-in-Charge

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls etc as in reapir complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC(SWR) bends of any radius, for 110mm bore pipes, with access doors, complete all as specified and as directed by the Engineer-in-Charge.

S & F 75mm bore PVC (SWR) bends of any radius with access doors complete all as specified and as directed by the Engineer-in-Charge.

S & F GI tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

S & F GI tubing 20 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

Demolition of concrete in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

M & L 25mm thick plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in sub base, finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L Non Skid coloured ceramic tiles premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and inculding 15mm thick screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M&L glazed ceramic coloured tiles premium/1st quality in vertical surfaces/skirtings/dados of size 300x600 x7mm/ 450x 350x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L vitrified ceramic light shade tiles 1st quality (square/rectengular), 10mm thick, area of each tile exc 0.42 sqm but not exc 1.00 sqm as in floor, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed by the Engineer-in-Charge.

M&L vitrified ceramic light shade tiles 1st quality (square/rectengular), 10mm thick, area of each tile exc 0.42 sqm but not exc 1.00 sqm as in skirting/dado, set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including rendering 10 mm thick in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engr-in-charge.

M&L brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M & L 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

S & F factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on boths face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

S & F factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

S & F flush shutters 35 mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete all as specified and as directed by the Engr-in-charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet on single side used instead of plain colour PVC sheet reinforced with MS square tube, edges will be painted to match with prelam sheet and fixed in opening complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made solid PVC moulded door shutters with partical board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

Cutting holes in brick walls built in cement mortar exc half brick thick and not exc one brick wall for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed by the Engineer-in-Charge.

M & L 2nd class hardwood (Malyasian Sal ) plain , solid ,straight chowkhats and frames ,wrought , framed rebated on the solid ,rounded or chamfered put together with glue pinned at joints complete all as specified and as directed by the Engineer-in-Charge.

M&L 18 mm thick prelaminated particle board exterier grade (grade-1) confirming IS 14587, fixed with screws for kitchen cupboard and cabinet ,shelves for cupboard , including 6mm thick 1st class teak hardwood leeping patti on cut edge of boards as in repair complete all as specified and as directed by the Engineer-in-Charge.

M&L 12 mm thick prelaminated partical board interior grade prelaminated both side with decorative choice lamination fixed with screw to timber frame work/aluminium frame work complete all as specified and as directed by the Engineer-in-Charge.

S & F continuous (pino) hinges , width of flaps 30mm (when open) mild steel bright finish or electro galvanished complete all as specified and as directed by the Engr-in-charge.

S&F 100 mm long fancy type stainless steel handle complete all as specified and as directed by the Engineer-in-Charge.

S&F magnet catcher fixed in cabnet shutter (one portion) and wooden frame (other portion) with screw complete all as specified and as directed by the Engineer-in-Charge.

M & L 2nd class hardwood plain fillets square,rectangular or triangular in section of sectional area exceeding 6 sqcm and not exceeding 13 sqcm , clean sawn, secured with nails or brads complete all as specified and as directed by the Engineer-in-Charge.

S&F 150 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

S & F 100mm long mortice lock with two levers (vertical type), mild steel body complete all as specified and as directed by the Engineer-in-Charge

S&F powder coated aluminium section (minimum thickness of powder coating 50 micron) for doors,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge. Note : (a). Glazing shall be measured and paid separately; (b). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight; (d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel alround contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and as directed by the Engineer-in-Charge.

M&L rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-410-(Gde E-250) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs, guard bars and painting etc. all as shown on drawing No. TD-219 sheet 1/3 to 3/3 and TD-220 sheet 1/3 to 3/3 as applicable complete all as specified and as directed by Engineer-in-charge. Note: (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill made from 10 mm mild steel square bar as shown on drgs. (iii) Glazing, wire mesh shall be measured and paid for separately.

Supply and fixing 300mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

S & F rubber strips 3 to 4 mm thick and 65 to 75 mm wide on bottom rail of door for covering gaps between door and floor to avoid entry of insects, dust etc and fixed with screws complete all as specified and as directed by the Engineer-in-Charge.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F stainless steel butt hinges 100 mm long medium weight and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F aluminium(die cast) body hydraulically regulated designation No 3 universal type, suitable for shutter of 851 to 1000mm in width and weight between 61 to 80 kg and fixed complete all as specified and as directed by the Engineer-in-Charge.

M & L sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge

M & L sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple to old steel/wooden frame complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, chajjas, staircases, landings and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and as directed by the Engineer-in-Charge.

M & L RCC 1:1.5:3 type A-1 using 20mm graded crushed stone aggregate as in shelves and the like complete all as specified and as directed by the Engineer-in-Charge.

M&L TMT mild steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.

M & L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., work in rough finished flat surfaces of concrete complete all as specified and as directed by the Engineer-in-Charge.

S & F 5mm PVC hollow sheet (the thicknees of inner wall 0.7 to 1.00mm) wall panelling inclusive of solvent cement and fixing at site with U clip or PVC frame as per specifications and drawing complete all as specified including dismantling of existing wall paneling.complete all as specified and as directed by the Engineer-in-Charge.

M&L cleaning and removing all scale and dirt etc from PVC/RCC tanks and mouths of circulating pipe of capacity 500 litre and upto and including 1000 litre & writing on the tank with synthetic enamel paint not less than 70mm long and 2mm wide of words in shape like cleaned on : 15.06.2018 complete all as specified and as directed by the Engineer-in-Charge. NOTE :- unit rate shall be included to make small fittings such as elbow, socket, reducer, tee, union etc .

M&L cutting of trees including removal roots, cleaning of bushes , removel of trees , vegetation from wall/roof not exc 30 cm girth and making good the distrubed surfaces with the existing finishes complete all as specified and as directed by the Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc or for shafts, wells, manholes etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed by the Engineer-in-Charge.

Returning, filling in, including spreading, levlling ,watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by the Engineer-in-Charge.

Removing surplus excavated material to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M & L concrete bed in PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate to drain pipes including packing under and haunching against the sides of pipes, after they are laid and tested for 110 mm dia (internal) pipes complete all as specified and as directed by the Engineer-in-Charge. (Pipes shall be measured & paid separately).

M&L for cleaning of sewage line up to first man holes blockage of WC, EWC,bathroom,floor trap of WHB/kitchen pipe etc complete all as specified and as directed by the Engineer-in-Charge.

Cleaning of sludge from Ist main hole by mechanical or any other mean and removal of sludge exc 50m but not exc 100m complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china table top wash hand basin white, of size 565mmx420mmx140mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc complete all as specified and as directed by the Engineer-in-Charge.

Single pieace water closet wtih PP soft close seat cover, hinges, fixing accessories and accessories set, cistern fittings S or P Trap complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No SLS -WHT-6855S / /CERA Cat part No.S10131095 /Hindware Cat Part No.92099 (S-30)

CP Brass wash hand basin mixer for mixing hot and cold water screwed down for 15mm dia pipe including waste popup with 450mm long braided hoses and all connecting fittings complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar Cat Part No QQP-7167BPM / Cera Cat Part No.F2007461 / Hindware Cat Part No.F 480011

Brass wall mixture 3-in-1 system with provision for both hand shower and overhead shower complete with 115 mm long bend pipe , connecting legs & wall flange without hand & overhead shower complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar Cat Part No QQT-7309 /Hindware Cat Part No.F 120019

Bib tap 15mm dia brass chromium plated fancy type with crutch or butterfly handle screwed down for iron pipe and fixed complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar Cat Part No : QQP-7037PM / Cera Cat Part No.F1003151 / Hindware Cat Part No.F 330041

15mm bore angular valves, fancy type brass chromium plated with long shank and cup (Concealed) type complete fixed as in rtepair complete all as specified and as directed by the Engineer-in-Charge. Make :Jaquar : Cat Part- QQP-7053PM / Cera Cat Part No.1003201 / Hindware Cat Part No.F 370006

Brass chromium plated tublar towel rail, 20mm dia, D type 60cm long between flanges complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No: ACN-1101S/Cera Cat Part No.F5002103

Brass CP Single towel rack 600 mm long between flanges including brackets complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1181FHS/Cera Cat Part No. F5007101 / Hindware Cat Part No.F 890012

Brass CP Towel ring round between flanges including fixing with brass screws complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1121BN/Cera Cat Part No.F5007105 / Hindware Cat Part No.F 880007

Brass CP toilet paper holder including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : AKP-35753PS/Cera Cat Part No.F5007109 / Hindware Cat Part No.F 840009

Brass CP SOAP DISH HOLDER including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1131N/Cera Cat Part No.F500716 / Hindware Cat Part No.F 840006

Corner glass slelf (with bracket) including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1173/Cera Cat Part No.F5005101 / Hindware Cat Part No.F 890009

Glass slelf (with bracket) including fixing with brass screws to wall complete fixed as in repair complete all as specified and as directed by the Engineer-in-Charge. Make : Jaquar Cat Part No : ACN-1171N/Cera Cat Part No.F5005301/ Hindware Cat Part No.F 840011

S&F 5 to 6mm thick mirror including ingraved any pattern, with wooden beading of any size fixed to wall with chromium plated brass screws and cup washers and all connected fitting as in repair complete all as specified and as directed by the Engr-in-charge.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridges complete all as specified and as directed by the Engineer-in-Charge.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick having zinc coating 150 grams per Sqm (Az 150) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

S & F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa having zinc coating 150grams/Sqm (Az-150) as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wooden scantling of any description not otherwise provided for complete all as specified and as directed by the Engineer-in-Charge.

S & F rolled mild steel sections as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates of Fe-410-W (Grade E-250) quality A complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete in existing sunken floor etc and removal of the same to a distance exceeding 250 mtr and not exceeding 500 mtr, depostied where directed complete all as specified and as directed by the Engineer-in-Charge.

S&F medium grade GI tubing of size 40mm dia as in spouts complete all as specified and as directed by Engineer-in-Charge

M&L PCC 1:5:10 type E-2, using 40 mm graded crushed stone aggregate as in filling in sunken floor, rounded or chamfered on edges complete all as specified.as directed by the Engineer-in-Charge.

M&L providing sunken floor water proofing treatment comprising of the following :- (a) Scrapping the surface with wire brush and cleaning with water and alloy to dry. (b) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound @ 2% by weight of cement or as per manufacturer's instructions. (c) 15 mm thick cement plaster (1:3) mixed with water proofing compound @ 2% by weight of cement or as per manufacturer instruction ( the corners will be made round in concave shape) and finished even and fair without using extra cement. (d) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound @ 2% by weight of cement or as per manufacturer's instruction. (e) Applying one coat of hot blown bitumen grade 85/25 confirming to IS-702 @1.20kg/sqm (f) Providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt using butane gas torch and ceiling all joints. (g) Applying one coat of hot blown bitumen grade 85/25 confirming to IS-702 @1.20kg/sqm.

M & L 40mm thick plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in floor, laid in panels and surface finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

S&F Glass dividing strips, 38 mm wide and 3 mm thick inserted in position to confirm to design complete all as spd and directed by Engineer-in-Charge.

S & F as in repair PVC tank lid/cover suitable for capacity 500 ltr and upto and including 1000 ltrs with and including locking arrangments such as nuts, bolts etc complete all as specified and as directed by the Engineer-in-Charge.

M & L 75 mm thick PCC 1:4:8 Type D-1 using 20mm graded crushed stone aggregate as in sub base of floor/ hard standing etc and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Dismantling Brick tiles or terracing tiles, single layer on roofs complete all as specified and as directed by the Engineer-in-Charge.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and as directed by the Engineer-in-Charge.

M & L roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, complete all as specified and as directed by the Engineer-in-Charge.

M & L brushing neat cement slurry @ 3.0 kg cement per sqm, complete all as specified and as directed by the Engineer-in-Charge.

M & L providing cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in roof kerbs, mud stops, padding on roof and finished even and smooth complete all as specified and as directed by the Engineer-in-Charge.

Material & Labour for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3, complete, all as specified and as directed by the Engineer-in-Charge.

M & L carring out roof treatment consisting of following:- (a) Cleaning of roof surface by sweeping and washing down with water to remove dust etc, (b). Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bitumious primer @ 0.40 ltr /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temprature and viscosity 70-160 cps over the primer coat with overlap of 100mm at the side and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc after preparing the surface complete as per standred practice as per manufacture's instructions . The vital physical and chemical parameters of the membrane shell be under ;- (i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms (ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d-5147) (iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane only complete all as specified and as directed by the Engineer-in-Charge.

M & L 40 mm thick brick tiles laid on screed bed and joints grouted flush in CM (1:3) mixed with 5% crude oil by weight of cement including screed bed 15 mm thick in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Description same all as per item No 145 here-in-above but using old servicable brick tiles obtained from item No. 138 here-in -above including cleaning old brick tiles complete all as specified and as directed by the Engineer-in-Charge.

M &L 10mm thick vitrified coloured paver tiles (Endura Tiles) of size 300 x 300mm in floors etc set and jointed in neat cment slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1 :4 ,complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 250 ltr and not exc. 500 ltrs and removing from site complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 500 ltr and not exc. 1000 ltrs and removing from site complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge.

S&F 100mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frames) area n. exc 1.5 Sqm each and removal from site complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exc 1.5 sqm but not exc 4 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-charge.

Taking down shutters of any description area not exc 1.00 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge.

Schedule 'B' Part-II (E/M itmes) Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, regulators, socket outlet, ceiling rose etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall surfaces and on surface on ceiling surfaces and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. and making smooth the disturbed surfaces as per existing for one light/fan/exhaust fan point controlled by one way switch, complete all as specified and as directed by Engineer-in-Charge. Note :- a) .All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately .

Description same all as per item No. 158 here-in-above but for One 3 pin, 5 Amps, socket outlet controlled by one switch on independent board, complete all as specified and as directed by Engineer-in-Charge.

Description same all as per item No. 158 here-in-above but for One 3 pin 5 Amps socket outlet controlled by one switch on same board, complete all as specified and as directed by Engineer-in-Charge.

Description same all as per srl item No 158 here-in-before but for one socket outlet 15 Amp with 4 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fix modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply & fix modular socket outlet 2/3 pin, 5 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply & fix modular socket outlet 2/3 pin, 6/16 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

S&F electronic Fan step regulator modular 110 watt, 2 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified and as directed by the Engineer-in-Charge.

S&F modular bell push 6 Amp, 1 way, 1 module 230 volts complete all as specified and as directed by the Engineer-in-Charge.

Supply & fix as in repair calling bell ding dong AC 230 volt complete all as specified and as directed by the Engr-in-charge.

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified and as directed by Engineer-in-Charge.

Supply and fix lamp holder,PVC/ polycarbonate type, with back plate for angular batten fittings complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing LED batten fitting 18-20 watt, 4 feet, 6500K aluminium housing and electronic driver including tube rod cool/warm type industrial model complete connecting with copper conductor flexible cable from ceiling rose to connector of the light as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing LED batten fitting 10-12 watt, 2 feet, 6500K aluminium housing and electronic driver including tube rod cool/warm type industrial model complete connecting with copper conductor flexible cable from ceiling rose to connector of the light as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing LED surface mounted bulk head luminaries 8-10 watt with min 800 lumen, industrial model, IP 65, auminum housing, surge protection including driver & LED lamp etc complete with all accessories connecting with copper conductor flexible cable from ceiling rose to connector of the light as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA 'C' curve as in repair complete all as specified and as directed by the Engr-in-charge.

Supply and fix sheet metal MCB DB SPN 8 way with 200 Amps rated bus bar single pole and neutral with acrylic double door IP-43 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge.

Supply and fix sheet metal enclosure Vertical triple pole & neutral (VTPN) with TPN MCCB 125 Amp for 415 volts 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and including lugs/thimbles duly crimped for connection, necessary PCC work and making smooth the disturbed after removing old Unserviceable MCB DB surface complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix MCB SP, 6-32 Amps, 240 volt,10 KA , 'B' / 'C' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix MCB SPN, 32/40 Amps, 240 volt,10 KA, 'B' / 'C' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge.

S & laying as in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall and surface on ceiling in PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Supply and laying XLPE insulated, armoured heavy duty electric cable 25 sqmm cross sectional area, 3.5 core with aluminium conductor, 1100 volts grade as in repair complete all as specified and as directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for laying of cables. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed by Engineer-in-Charge.

Removing excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed by Engineer-in-Charge.

M&L for sand cushoning under the cable for protecting the cable being damaged from external load complete all as specified and as directed by Engineer-in-Charge. Note: punned thickness shall be measured for payment.

Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1 flat, size 250 mm x 150mm x 40mm complete all as specified and as directed by Engineer-in-Charge.

S&F light grade GI Tubing of size 40mm dia for cable protection and fixed with clamp to pole and wall with nut bolts as in repair complete all as specified and as directed by Engineer-in-Charge

S&F LED Bldg Security Light Fittings of capacity 40 -45 watt made up of die cast aluminium housing with black epoxy powder coated with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including service bracket of GI pipe 32 mm bore medium grade of length 0.9 mtr with MS clamps, bolts, nuts, and washers and suitable reducer for connecting fitting to GI pipe as required at site and two coats of synthetic enamel paint over one coat of red oxide primer on mild steel work and making electrical connection, including disconnecting and taking down existing old U/S fitting complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing LED flat panel 2' x 2' size fully difused surface/ recess mounted fitting (grid/ gypsum type) 36-40 watt , 5700K, warm/cool white with powder coating and CRCA front cover including frame with provision of PVC flexible copper conductor cable to light fitting as in repair complete all as specified and as directed by the Engr-in-charge.

Supply and fixing indoor decorative LED tube light fitting box type 1x18/20 watt with opal diffuser, high efficient aluminium housing body in CRCA body suitable for LED tube, high efficient, AC 220-240 volts, 50 Hz and including 1x18/20 watt LED tube rod luminaries (Warm/Cool as per site requirement) environment friendly, high efficient, T8 with aluminium extrusion heat sink connecting with copper conductor flexible cable from ceiling rose to connector of the light including disconnecting and taking down existing light fitting and removal complete all as specified and as directed by the Engineer-in-Charge.

S & F LED post top luminaire 30W- 35W, 5700K, IP-65 made of pressure die-cast aluminium housing & clear glass 240 volt, 50HZ, AC supply complete with all accessories internally pre wired including connecting with fitting and including provision of 3 core PVC flexible copper conductor from electric supply source to connector of the light, including disconnecting and taking down existing light fitting and removing old unserviceable fitting complete all as specified and as directed by the Engr-in-charge.

Material & labour as in repair for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth lead of 4mm dia GI wire by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to main switch board or main control board as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/c both ways with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing complete all as directed by Engineer-in-Charge and earth testing on completion .

MAYANK ENTERPRISES

Durga Enterprises

bhagwandasswazirchand