PMMSY-Construction Of State Of Art Wholesale Fish Market-Aluva In Ernakulam, Kerala

Amount

Appendix A-Pile

2.32 : Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

20.2.5 : Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).600 mm dia piles

OD31037/2024_2025 : Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of<br>grade M-25 of specified diameter and length below the pile cap to carry a safe<br>working load not less than specified, excluding the cost of steel reinforcement but<br>including the cost of boring, with bentonite solution and temporary casing of<br>appropriate length for setting out and removal of same and the length of the pile to be<br>embedded in the pile cap etc. all complete, including removal of excavated earth with<br>all lifts and leads (Length of pile for payment shall be measured upto bottom of pile<br>cap).900 mm dia piles

OD31038/2024_2025 : Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M25 of specified diameter and length below the pile cap to carry a safe working load not less than<br>specified, excluding the cost of steel reinforcement but including the cost of boring, with<br>bentonite solution and temporary casing of appropriate length for setting out and removal of<br>same and the length of the pile to be embedded in the pile cap etc. all complete, including<br>removal of excavated earth with all lifts and leads (Length of pile for payment shall be<br>measured upto bottom of pile cap).800 mm dia piles

OD31039/2024_2025 : Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M25 of specified diameter and length below the pile cap to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).700 mm dia piles

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

20.6.1.1 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile upto 50 tonne capacityInitial test

20.6.1.2 : Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile upto 50 tonne capacityRoutine test

Appendix B: Earthwork and PCC

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1 : Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

OD25420/2024_2025 : Providing Z steel sheet pile of size 400x185x7.5/8.5 driving down vertically in lines and levels,<br>interlocking with adjacent piles with suitable pile driving unit and all accessories including all<br>labour hire charges etc ,complete as per the direction of departmental officers.

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

2.27 : Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming consolidating and dressing complete.

23.7 : Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.

2.34.1 : Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos / Lindane emulsifiable concentrate of 20%

2.35.1.1 : Diluting and injecting chemical emulsion for POST -CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion):Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete:With Chlorpyriphos /Lindane E.C. 20% with 1% concentration

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.2.3 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Appendix C: RCC works

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.34.1 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum).

5.34.2 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-35 grade concrete instead of M-25 grade BMC/RMC. (Note: Cement content considered in M-35 is @ 350 Kg/cum).

5.34.3 : Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable/ recoverable separately.Providing M-40 grade concrete instead of M-25 grade BMC/RMC.(Note : Cement content considered in M-40 is @ 360 kg/cum).

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.31 : Extra for laying reinforced cement concrete in or under water and /or liquid mud including cost of pumping or bailling out water and removing slush etc., complete. Note:- The quantity will be calculated by multiplying the depth measured from the subsoil water level upto the centre of gravity of the R.C.C. under subsoil water with the quantity of R.C.C. in cubic metre executed under subsoil water. The depth of centre of gravity shall be reconed correct to 0.1m. 0.05 m or more shall be taken as 0.1 and less than 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under subsoil water conditions.

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

Appendix D: Shuttering

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.21 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick.

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.19 : Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.11.1 : Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

5.28 : Providing and fixing in position 12 mm thick bitumen impregnated fibre board conforming to IS: 1838, including cost of primer, sealing compound in expansion joints.

5.29.2.2 : Providing and fixing sheet covering over expansion joints with iron screws as per design.200 mm wide

22.4.1 : Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:Serrated with central bulb ( 225 mm wide, 8-11 mm thick)

Appendix E: Solid Block Masonry

50.6.3.1 : Solid block masonry using pre cast solid blocks ( Factory made) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth for 10 cm thick wall in CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding etc complete

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

50.6.1.8 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 15cm in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

6.38 : Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above floor 2 level up to floorV level in cement mortar 1:4 (1 cement :4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

6.3.1 : Brick work with common burnt clay machine moulded perforated bricks of classdesignation 12.5 conforming to IS: 2222 in superstructure above plinth level up tofloor five level in cement mortar 1:6 (1 cement : 6 coarse sand):With F.P.S. ( non modular ) bricks

6.15 : Extra for providing and placing in position 2 Nos 6 mm dia M.S bars at every third course of half brick masonry.

19.33 : Constructing soak pit 1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

OD31517/2024_2025 : Honey-comb brick work with 10/11.4 cm thick with common burnt clay F.P.S. (non modular)<br>bricks of class designation 7.5 including grouting with cement mortar 1:6 (1 cement : 6 fine<br>sand). for foundation and plinth

Appendix F: Roofing works

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.10.2 : Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

OD25408/2024_2025 : Providing and fixing MS Trellis work, consisting of epoxy finished MS frame work , using<br>RHS 96x48x4 for vertical and horizontal supports and fixing weived stainless steel mesh (make<br>mesh tech or equivalent ) having wire thickness of 1mm with a weft 1.69mm and warp 1.509<br>mm and supported by frame with , all fixing arrangements etc. complete.

OD25409/2024_2025 : Providing and fixing Name board fixing epoxy finished MS frame work , using RHS 96x48x4<br>for vertical and horizondal supports and fixing weived stainless steel mesh make (mesh tech or<br>equivalent )having wire thickness of 1mm with a weft 1.69mm and warp 1.509 mm and<br>supported by frame , all fixing arrangements etc. complete

OD25411/2024_2025 : Providing and fixing Aluminium Tile profile sheets (Oralium - Novatile , size, shape and pitch<br>of corrugation as approved by Engineer-in-charge) 0.560 mm or nearest available thickness.<br>The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM<br>seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of<br>purlins, rafters and trusses and including cutting to size and shape wherever required.

OD25412/2024_2025 : Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in<br>0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO<br>designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet<br>and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm<br>with 3mm thick EPDM seal and SS plain washer complete :Precoated/mill finish aluminium<br>Ridges plain<br>(500- 600mm)

OD25413/2024_2025 : Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in<br>0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO<br>designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm<br>with 3mm thick EPDM seal and SS plain washer complete :Precoated/mill finish aluminium<br>Barge board<br>(Upto 200 mm)

OD25414/2024_2025 : Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in<br>0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO<br>designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet<br>and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm<br>with 3mm thick EPDM seal and SS plain washer complete :Precoated/mill finish aluminium<br>Flashings/ Aprons<br>(Upto 600 mm)

OD25415/2024_2025 : Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in<br>0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO<br>designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet<br>and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm<br>with 3mm thick EPDM seal and SS plain washer complete : 600mm overall girth Roof gutter

OD25416/2024_2025 : Supplying and fixing 18mm thick colured Multi layer Polycarbonate Panels of<br>(SUNPAL® – PALRAM make or equivalent ) of size 1000 mm width x 11800mm<br>length.The panel shall have fire rating as per rating as per EN13501 B,s1,d0.The polycarbonate<br>system shall have weight not less than 3.11 kgs/m2.and a U value <= 1.5<br>watts/m2/°C.The whole system shall be secured with Aluminium end profile using Tfasteners of thickness not less than 2mm having minimum three points for fastening with selfdrilling Hex Headwith EPDM seal. Screws to have proper fixing with the existing structural<br>framework which is fabricated in accordance to the requirement.

OD25417/2024_2025 : Under deck Insulation on Roof sheet using Cross linked PE Sheet One side foil<br>(Sliplop)13mm X 1.25 mtr X 25mtr .Unroll the INSUshield insulation from the ridge to eave<br>end that means from higher level to lower and the foil must face toward the roofing<br>sheet.Stretch and fix the INSUshield insulation sheet with self drilling screw on ridge end and<br>eave end so that the saggy is not visible between the purlins.Put the metal roofing sheet and<br>screw as usual .Place the next roll of INSUshield alongside the earlier roll side by<br>side.Complete the entire roof by repeating this process.

OD25418/2024_2025 : Supplying and fixing Stainless steel rain chain gutter 100mm OD with 2mm thick chain for<br>roof down water with necessary fittings etc complete<br>

OD25419/2024_2025 : Providing leak proof on roof sheet to wall joints using 1mm thick aluminium sheet inserted in<br>wall and sealed properly as per the direction of Engineer in charge<br>

Plastering

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.11 : 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 ( 1 cement : 6 fine sand).

13.22 : Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

50.13.1 : 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

5.30 : Add for plaster drip course / groove in plastered surface or moulding to R.C.C. projections.

OD31830/2024-2025 Providing Plaster art of required pattern , applying 18mm thick two coat plastering and<br>providing plaster art on required pattern etc as per design<br>

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

OD31831/2024-2025 Providing and fixing Fibre mesh in the joints of concrete and brick masonry, electrical and<br>plumbing conduits chasing area etc. wherever necessary racked and grouted /pointed on joints ,<br>covered by 150mm wide fibre net fixing before plastering . Cost including all materials &<br>labour charges all lead and lift scaffolding curing etc. complete for walls.

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

22.16 : Providing and laying in situ five course water proofing treatment with APP (Atactic Polypropylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd & 4th courses of bonding material @ 1.20 kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd layer of roofing membrane APP modified Polymeric membrane 2.0 mm thick of 3.00 Kg/ sqm weight consisting of five layers prefabricated with centre core as 100 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 5th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately).

22.23.1 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For vertical surface two coats @0.70 kg per sqm

22.23.2 : Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm.

Flooring

11.5 : 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufactures specification. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

OD31832/2024-2025 (Ref: 11.26.1)Kota stone (prepolished) slab flooring of size 600x600mm over 20 mm ( average)<br>thick base laid over and providing 3mm spacer gap on both direction and filling epoxy approved<br>by Engineer-in-charge, including rubbing and polishing complete with base of cement mortar<br>1:4 (1 cement : 4 coarse sand)25 mm thick

OD31833/2024-2025 (Ref: 11.26.1)Kota lapotra finish stone slab flooring of size 600x600mm over 20 mm ( average)<br>thick base laid over and providing 3mm spacer gap on both direction and filling epoxy approved<br>by Engineer-in-charge, including rubbing and polishing complete with base of cement mortar<br>1:4 (1 cement : 4 coarse sand)25 mm thick

OD31835/2024-2025 (Ref: 11.32)Extra for Kota lapotra finish stone / sand stone in treads of steps and risers using<br>single length up to 1.20 metre.

OD31836/2024-2025 (Ref: 7.37.1.1 & 7.38.1.1)Stone work (machine cut edges veneer work) for wall lining upto<br>10 m height,with special adhesive over 12 mm thick cement mortar 1:3 (1 Cement :3 coarse<br>sand), providing 3mm spacer gap on both direction and joined with cement mortar 1:2<br>(1cement:2 stone dust), including rubbing and polishing complete. (To be secured to the<br>backing and the sides by means of cramps and pins which shall be paid for separately<br>Kota lapotra finish stone slabs exposed face dressed and rubbed.25 mm thick

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

OD33194/2024-2025 (Ref: 11.49.3)Providing and laying Vitrified tiles in walls with different sizes (thickness to be<br>specified by the manufacturer), with water absorption less than 0.08% and conforming to IS :<br>15622, of approved brand & manufacturer, in all colours and shade, laid with cement based<br>high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in<br>average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made<br>separately).Size of Tile 800x800 mm<br>

Joineries

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.2 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

OD31840/2024-2025 (Ref: 21.3.3)Providing and fixing glazing in aluminium door, window, ventilator shutters and<br>partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural<br>drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be<br>paid in basic item): With Toughened glass 12 mm thickness.

10.29.2 : Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

OD31841/2024-2025 (Ref: 21.3.2)Providing and fixing glazing in aluminium door, window, ventilator shutters and<br>partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural<br>drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be<br>paid in basic item):With 6 mm thick clear heat strengthened glass<br>

21.2.1 : Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

OD31844/2024-2025 (Ref: 10.31)Supplying and fixing MS Grill doors using MS angle 35x35x5mm for door frame ,<br>25x25x4mm for shutter frame and 12mm square rod @ 100mmC/C for shutter as per approved<br>design and drawing . The rate shall include all materials, labour and hire charges for fabrication,<br>all hardware , fixtures and applying one coat epoxy primer etc. complete as directed by<br>Engineer in charge.

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

10.8.2 : Extra for providing mechanical device chain and crank operation for operating rolling shuttersExceeding 16.80 sqm in area

10.9 : Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer -in-Charges, (area of grill to be measured).

OD31845/2024-2025 Door frame fixing with anchor bolt - Supplying, drilling/cleaning hole and fixing appropriate<br>length of ETA Approved HRD H 10 anchor suitable for fastenings both on concrete &<br>masonry/aerated blocks. Length of anchor should be decided on the basis of embedment depth<br>in base material, total frame thickness & gap between frame and base material. Anchor<br>comprises of 10 mm diameter Polyamide PA 6 grade sleeve and of 7 mm diameter double<br>threaded 6.8 grade Hex head double threaded screw made of carbon steel galvanized to<br>minimum 5 microns. Fixing methodology to be followed as per manufacturers guidelines.<br>

OD31846/2024-2025 Providing and fixing tiled false ceiling of 8mm PVC laminated gypsum board Tile of size<br>595x595 mm ( Gyproc Gyprex due d rop or equivalent) in reveal edge , true horizontal level,<br>suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized<br>@120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably<br>spaced joints to get required length and of size 24x32mm made from 0.30 mm thick (minimum)<br>sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of<br>0.30mm thick (minimum) sheet, 1200mm long spaced between main "T" at 600<br>mm center to center to form a grid of 1200x600 mm and secondary cross "T" of<br>length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked<br>at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size<br>24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required<br>cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke<br>detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats<br>of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 8mm dia and 45 mm long dash fasteners, 4<br>mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at<br>1200 mm center to center along main T, bottom exposed width of 24mm of all T-sections shall<br>be pre-painted with polyester paint, all complete for all heights as per specifications, drawings<br>and as directed by<br>Engineer-in-charge.

PAINTING

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.47.1 : Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

13.83.2 : Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour.Two coats

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

OD31827/2024-2025<br>(Ref: 13.52.1)Finishing with PU paint (two or more coats) at all locations prepared and applied<br>as per manufacturer's specifications including appropriate priming coat, preparation of<br>surface, etc. complete. On steel work

OD31828/2024-2025<br>Supplying and fixing rubber corner safe guard 120cm height of size 100x100x30mm with<br>60mm reflective tape 8nos of size fixed on parking area column corners.

16.48.1 : Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS: 164, on bituminous surface in white / yellow shade, including cleaning the surface of all dirt, scales oil, grease and foreign material etc. complete.New work (Two or more coats)

Water Supply and Sanitary Installation

17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

17.8 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

17.5.1 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required:Single half stall urinal with 5 litre PVC. automatic flushing cistern

8.10.2 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in Charge and finished smooth.Granite Stone of approved shade

17.73.2 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighting not less than 190 gms

17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms

50.17.1.4 Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge

18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

17.10.1.3 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board510x1040 mm bowl depth 200 mm

17.10.2.2 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink without drain board610x460 mm bowl depth 200 mm

OD26430/2024-2025 Supplying & Fixing sink mixer cock for sink by making good the walls wherever required.with accessories like teflon tape ,shellac, waste and silicone sealant. (based on 18.49.1)

OD26431/2024-2025 Supplying & Fixing sink cock for sink by making good the walls wherever required.with accessories like teflon tape ,shellac, waste and silicone sealant. (based on 18.49.1)

18.52.1 Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

18.22.2 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:150 mm diameter

18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

17.34.1 Providing and fixing toilet paper holder:C.P. brass

OD25421/2024-2025 Providing and Fixing Wall mounted stainless steel Grab bar 600mm long with anti slip coating including the cost of carriage and fixing as specified as per the direction of engineer in charge

17.70.1 Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the center of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

OD26434/2024-2025 Supplying & Fixing electrically operated horizontal storage heater with M.S. steel glass lined vessel with 1.5-2 Kw heating element, auto-thermostatic switch, neon indicator lamp, pressure relief valve etc. as specified in the specifications, complete in all respects

Internal Drainage

OD26453/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type B (IS:13592) including injection moulded fittings with bosses where required eg tees, bends, clamps couplings and adapters & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete.and jointing with adhesive approved by manufactures including cutting and making good the walls or surface mounted with clamps as required at site 160mm pipe (based on 50.18.8.9.2)

OD26454/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type B (IS:13592) including injection moulded fittings with bosses where required eg tees, bends, clamps couplings and adapters & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. and jointing with adhesive approved by manufactures including cutting and making good the walls or surface mounted with clamps as required at site 110 mm pipe (based on 50.18.8.9.2)

OD26452/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type B (IS:13592) including injection moulded fittings with bosses where required eg tees, bends, clamps couplings and adapters & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. and jointing with adhesive approved by manufactures including cutting and making good the walls or surface mounted with clamps as required at site 75 mm pipe (based on 50.18.8.8.2)

OD26451/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type B (IS:13592) including injection moulded fittings with bosses where required eg tees, bends, clamps couplings and adapters & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete. and jointing with adhesive approved by manufactures including cutting and making good the walls or surface mounted with clamps as required at site 50 mm pipe (based on 50.18.8.8.2)

OD31029/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type B(IS:13592 upto 200 mm dia and IS:4985 for above 200 mm dia pipes) including SWR fittings with bosses where required eg.tees, bends, clamps, couplings and adapters and cowls with sealing grooves and clamping with Position & jointing with 'O' rings including cutting and making good the walls and floors as required at site (For Vertical Shaft piping). 200 mm (based on 50.18.9.19.2)

OD31030/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type B(IS:13592 upto 160 mm dia and IS:4985 for above 160 mm dia pipes) including SWR fittings with bosses where required eg.tees, bends, clamps, couplings and adapters and cowls with sealing grooves and clamping with Position & jointing with 'O' rings including cutting and making good the walls and floors as required at site (For Vertical Shaft piping). 160 mm (based on 50.18.9.19.2)

OD31031/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type B(IS:13592 upto 110 mm dia and IS:4985 for above 110 mm dia pipes) including SWR fittings with bosses where required eg.tees, bends, clamps, couplings and adapters and cowls with sealing grooves and clamping with Position & jointing with 'O' rings including cutting and making good the walls and floors as required at site (For Vertical Shaft piping). 110 mm (based on 50.18.9.19.2)

OD31028/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type B(IS:13592 upto 75 mm dia and IS:4985 for above 75 mm dia pipes) including SWR fittings with bosses where required eg.tees, bends, clamps, couplings and adapters and cowls with sealing grooves and clamping with Position & jointing with 'O' rings including cutting and making good the walls and floors as required at site (For Vertical Shaft piping). 75 mm (based on 50.18.9.19.2)

OD31032/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type A(IS:13592 upto 160 mm dia and IS:4985 for above 160 mm dia pipes) including SWR fittings with bosses where required eg.tees, bends, clamps, couplings and adapters and cowls with sealing grooves and clamping with Position & jointing with 'O' rings including cutting and making good the walls and floors as required at site (For vent and rainwater pipes ). 160 mm pipe (based on 50.18.9.19.2)

OD31033/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type A(IS:13592 upto 110 mm dia and IS:4985 for above 110 mm dia pipes) including SWR fittings with bosses where required eg.tees, bends, clamps, couplings and adapters and cowls with sealing grooves and clamping with Position & jointing with 'O' rings including cutting and making good the walls and floors as required at site (For vent and rainwater pipes ). 110 mm pipe (based on 50.18.9.19.2)

OD31191/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type A(IS:13592 upto 75 mm dia and IS:4985 for above 75 mm dia pipes) including SWR fittings with bosses where required eg.tees, bends, clamps, couplings and adapters and cowls with sealing grooves and clamping with Position & jointing with 'O' rings including cutting and making good the walls and floors as required at site (For vent and rainwater pipes ). 75 mm pipe (based on 50.18.9.19.2)

OD31193/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (SWR) of Type A(IS:13592 upto 63 mm dia and IS:4985 for above63 mm dia pipes) including SWR fittings with bosses where required eg.tees, bends, clamps, couplings and adapters and cowls with sealing grooves and clamping with Position & jointing with 'O' rings including cutting and making good the walls and floors as required at site (For vent and rainwater pipes ). 63 mm pipe (based on 50.18.9.19.2)

OD31197/2024-2025 Supplying, Installing & Testing at site in position uPVC Deep seal Floor trap (ht 7") supporting on G.I. slotted rails (1.6 mm thick), Full threaded rod , Anchor Fasteners etc at site. 110 X 75mm dia out let (Multiple Floor Trap)

OD31203/2024-2025 Supplying, Installing, Testing & Commissioning at site in position 110mm dia deep seal PVC 'P' trap without boss tee and access cap Including all necessary fittings & supports complete

OD31205/2024-2025 Supplying, Installing, Testing & Commissioning at site in position 110mm dia deep seal PVC 'P' trap without boss tee and access cap Including all necessary fittings & supports complete

OD26625/2024-2025 Supplying, Installing & Testing at site in position low noise 3 layered Poly Propylene pipes & push fit fittings(PP) of sound level 13 dB @ 4L/sec for non pressurized domestic drainage in accordance with system standards of DIN 4102, the density of the pipe & fittings material should be 1.9 g/cm3 including cutting and making good the walls and floors as required at site (For Vertical & Horizontal Shaft piping of Kitchen Waste). 160 mm dia

OD26626/2024-2025 Supplying, Installing & Testing at site in position low noise 3 layered Poly Propylene pipes & push fit fittings(PP) of sound level 13 dB @ 4L/sec for non pressurized domestic drainage in accordance with system standards of DIN 4102, the density of the pipe & fittings material should be 1.9 g/cm3 including cutting and making good the walls and floors as required at site (For Vertical & Horizontal Shaft piping of Kitchen Waste). 110 mm dia

OD26627/2024-2025 Supplying, Installing & Testing at site in position low noise 3 layered Poly Propylene pipes & push fit fittings(PP) of sound level 13 dB @ 4L/sec for non pressurized domestic drainage in accordance with system standards of DIN 4102, the density of the pipe & fittings material should be 1.9 g/cm3 including cutting and making good the walls and floors as required

OD26628/2024-2025 Supplying, Installing & Testing at site in position low noise 3 layered Poly Propylene pipes & push fit fittings(PP) of sound level 13 dB @ 4L/sec for non pressurized domestic drainage in accordance with system standards of DIN 4102, the density of the pipe & fittings material should be 1.9 g/cm3 including cutting and making good the walls and floors as required at site (For Vertical & Horizontal Shaft piping of Kitchen Waste). 50 mm dia

OD26629/2024-2025 Supplying, Installing & Testing at site in position Polypropylene P Trap (sound level 13 dB @ 4L/sec) of size 110 mm dia of approved make for Drainage, complete with all necessary fittings of approved make, as per drawings

OD31210/2024-2025 Supplying, Installing & Testing at site in position Deep seal Polypropylene Floor trap (ht 7") (sound level 13 dB @ 4L/sec) supporting on G.I. slotted rails (1.6 mm thick), Full threaded rod , Anchor Fasteners etc at site.110 X 75mm dia out let (Multiple Floor Trap)

OD31213/2024-2025 Supplying, Installing & Testing at site in position Polypropylene Rodding eye (sound level 13 dB @ 4L/sec) supporting on G.I. slotted rails (1.6 mm thick), Full threaded rod , Anchor Fasteners etc at site. 110 mm dia

OD31241/2024-2025 Supplying, Installing & Testing at site in position Polypropylene Rodding eye (sound level 13 dB @ 4L/sec) supporting on G.I. slotted rails (1.6 mm thick), Full threaded rod , Anchor Fasteners etc at site. 75mm dia

OD26550/2024-2025 Installing at site in position Floor Drain Lock type (SS304) of 1.2 mm thick. 125 x 125mm Square

OD26555/2024-2025 Supplying & Installing at site in position SS (SS 316) Drain Trough With Grating of following size having silt basket fits inside gratings frame to trap debris and particles . 300 X 300 mm

OD26556/2024-2025 Supplying & Installing at site in position SS (SS 316) Drain Trough With Grating of following size having silt basket fits inside gratings frame to trap debris and particles . 1000 X 300 mm

OD31249/2024-2025 Supplying, Installing & Testing at site in position PVC Rodding Eye (6 kg/cm2) complete in all respects. 160 mm dia

OD31248/2024-2025 Supplying, Installing & Testing at site in position PVC Rodding Eye (6 kg/cm2) complete in all respects. 110 mm dia

OD31247/2024-2025 Supplying, Installing & Testing at site in position PVC Rodding Eye (6 kg/cm2) complete in all respects. 75 mm dia

OD31259/2024-2025 Supplying & Installing at site in position 125 X 125 mm square cast SS (304 grade) cleanout with Teflon gasket & SS key for opening, complete in all respects

Water Supply

OD31275/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make 20mm dia pipe

OD31277/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings 25 mm pipe ( based on 18.7.3)

OD31278/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings 32mm dia uPVC pipe (based on 18.7.4)

OD31279/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings 40mm dia uPVC pipe (based on 18.7.5)

OD31309/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings 50mm uPVC pipe (based on 18.7.6)

OD31311/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make 63mm uPVC pipe (based on 18.7.6)

OD31315/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make 80mm uPVC pipe (based on 18.7.6)

OD31319/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete for Sch 40 pipes concealing through the walls / floors including cutting and making good the wall to line and level wherever required as per drawings 20 mm uPVC pipes ( based on 18.8.2)

OD31320/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) for Sch 40 pipes concealing through the walls / floors including cutting and making good the wall to line and level wherever required as per drawings 25 mm uPVC pipe (based on 18.8.3)

OD31329/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 80 mm (based on 18.3.6)

OD31330/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 65 mm (based on 18.3.6)

OD31331/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 50 mm (based on 18.3.4)

OD31332/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 40 mm (based on 18.3.4)

OD31333/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 32 mm (based on 18.3.4)

OD31334/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 25 mm (based on 18.3.2)

OD31335/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 20 mm (based on 18.3.2)

OD25591/2024-2025 Supplying, Installing & Testing at site in position full way lever operated Forged Brass Ball valve of brass body with forged brass hard chrome plate (PN 25) of approved make with necessary Male Adapter (Brass Threads) fittings in position as per drawings. 15mm dia valve

OD25590/2024-2025 Supplying, Installing & Testing at site in position full way lever operated Forged Brass Ball valve of brass body with forged brass hard chrome plate (PN 25) of approved make with necessary Male Adapter (Brass Threads) fittings in position as per drawings. 20mm dia valve (based on 18.17.1)

OD25589/2024-2025 Supplying, Installing & Testing at site in position full way lever operated Forged Brass Ball valve of brass body with forged brass hard chrome plate (PN 25) of approved make with necessary Male Adapter (Brass Threads) fittings in position as per drawings. 25 mm dia valve (based on 18.17.1)

OD25588/2024-2025 Supplying, Installing & Testing at site in position full way lever operated Forged Brass Ball valve of brass body with forged brass hard chrome plate (PN 25) of approved make with necessary Male Adapter (Brass Threads) fittings in position as per drawings. 32 mm valve

OD25587/2024-2025 Supplying, Installing & Testing at site in position full way lever operated Forged Brass Ball valve of brass body with forged brass hard chrome plate (PN 25) of approved make with necessary Male Adapter (Brass Threads) fittings in position as per drawings. 40mm valve (based on 18.17.3)

OD25586/2024-2025 Supplying, Installing & Testing at site in position full way lever operated Forged Brass Ball valve of brass body with forged brass hard chrome plate (PN 25) of approved make with necessary Male Adapter (Brass Threads) fittings in position as per drawings. 50mm valve (based on 18.17.4)

OD25618/2024-2025 Supplying, Installing & Testing at site in position Butterfly valve (PN 16) wafer type of approved make with necessary PVC flanges, gaskets, nuts and bolts etc complete within position as per drawings.65 mm dia

OD25617/2024-2025 Supplying, Installing & Testing at site in position Butterfly valve (PN 16) wafer type of approved make with necessary PVC flanges, gaskets, nuts and bolts etc complete within position as per drawings. Butterfly valve (PN 16) 80mm

OD25616/2024-2025 Supplying, Installing & Testing at site in position Butterfly valve (PN 16) wafer type of approved make with necessary PVC flanges, gaskets, nuts and bolts etc complete within position as per drawings. 100 mm dia valve

OD25615/2024-2025 Supplying, Installing & Testing at site in position Butterfly valve (PN 16) wafer type of approved make with necessary PVC flanges, gaskets, nuts and bolts etc complete within position as per drawings. 150 mm dia valve

18.19.3.2 Providing and fixing gun metal non-return valve of approved quality (screwed end): 40 mm nominal boreVertical

18.19.4.2 Providing and fixing gun metal non-return valve of approved quality (screwed end): 50 mm nominal boreVertical

18.19.5.2 Providing and fixing gun metal non-return valve of approved quality (screwed end): 65 mm nominal boreVertical

OD25678/2024-2025 Supplying, Installing & Testing at site in position spring loaded vertically mounted brass Air Release Valves of approved quality and make on the top of the vertical water supply pipes as per specification and drawings. 20 mm dia

OD25679/2024-2025 Supply,Installation,Testing and Commisioning of C I Y-type stainer PN 10 with drain plug, SS screen 304 complete in all respects.(For upto 50 mm dia Brass Y -type stainer) 80mm

OD25683/2024-2025 Supplying, Installing & Testing at site in position Brass Float valve (PN 14) of approved make with PP float & nipple with brass threaded insert, brass back nuts, piston and bolts etc complete in all respect 40 mm dia (based on 18.18.3)

OD25711/2024-2025 Supplying, Installing, Testing & Commissioning at site in position IP 68 type Static water meter based on ultrasonic technology to eliminate measuring deviations caused by air pockets, suspended particles & sand. It should posss higher performance than Class-D requirements complete.Device should be BMS ompactable. 20mm

OD25712/2024-2025 Supplying, Installing, Testing & Commissioning at site in position IP 68 type Static water meter based on ultrasonic technology to eliminate measuring deviations caused by air pockets, suspended particles & sand. It should posss higher performance than Class-D requirements complete.Device should be BMS ompactable. 50 mm

External Sewerage and Storm Water Drain

OD26574/2024-2025 Supplying, Installing & Testing of pipes and conveying to position; and jointing to true lines and gradients, PVC pipe of IS 4985(6kg/cm2), jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure including Supplying, Supplying, Installing specials like bends, couplers, sockets, connections etc. as per provisions of IS: 1742-1983 (Code of practice for building drainage) complete.75 mm pipe (based on 50.18.9.19.2)

OD26575/2024-2025 Supplying, Installing & Testing of pipes and conveying to position; and jointing to true lines and gradients, PVC pipe of IS 4985(6kg/cm2), jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure including Supplying, Supplying, Installing specials like bends, couplers, sockets, connections etc. as per provisions of IS: 1742-1983 (Code of practice for building drainage) complete. 110mm pipe (based on 50.18.9.19.2)

OD31349/2024-2025 Supplying, Installing & Testing of pipes and conveying to position; and jointing to true lines and gradients, PVC pipe of IS 4985(6kg/cm2), jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure including Supplying, Supplying, Installing specials like bends, couplers, sockets, connections etc. as per provisions of IS: 1742-1983 (Code of practice for building drainage) complete. 160mm pipe (based on 50.18.9.19.2)

OD26584/2024-2025 Supplying & Laying of uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) wherever necessary, and conveying to position, cleaning, laying and jointing to true lines and gradients, ,jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure etc. complete.(for external water supply) 20 mm pipe (based on 50.18.9.12.1)

OD26585/2024-2025 Supplying & Laying of uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) wherever necessary, and conveying to position, cleaning, laying and jointing to true lines and gradients, ,jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure etc. complete.(for external water supply) 25 mm pipe (based on 50.18.9.12.1)

OD26586/2024-2025 Supplying & Laying of uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) wherever necessary, and conveying to position, cleaning, laying and jointing to true lines and gradients, ,jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure etc. complete.(for external water supply) 32 mm pipe (based on 50.18.9.12.1)

OD26587/2024-2025 Supplying & Laying of uPVC unthreaded pipes (As per ASTM D - 1785, ,Sch.40) of approved make for water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) wherever necessary, and conveying to position, cleaning, laying and jointing to true lines and gradients, ,jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure etc. complete.(for external water supply) 40 mm pipe (based on 50.18.9.12.1)

OD26588/2024-2025 Supplying & Laying of uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) wherever necessary, and conveying to position, cleaning, laying and jointing to true lines and gradients, ,jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test press

OD26589/2024-2025 Supplying & Laying of uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40) of approved make for water supply, complete with all necessary Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) wherever necessary, and conveying to position, cleaning, laying and jointing to true lines and gradients, ,jointing the pipe line as per specification, testing the pipe line after installation to the specified hydrostatic test pressure etc. complete.(for external water supply) 50 mm pipe (based on 50.18.9.12.1)

OD26618/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 20 mm (based on 18.3.2)

OD26617/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 25 mm (based on 18.3.2)

OD26616/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 32 mm (based on 18.3.4)

OD26615/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 40 mm (based on 18.3.4)

OD26614/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 50 mm (based on 18.3.4)

OD26613/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 65 mm (based on 18.3.6)

OD26612/2024-2025 Supplying, Installing & Testing at site in position uPVC unthreaded pipes (As per ASTM D - 1785 ,Sch.40, for reclaimed water-purple colour) of approved make for water supply, complete with all necessary Sch-40 Fittings (elbows, unions, tees, reducers, couplings, nipples etc.) complete with clamping in position with G.I. "U" bolts (8 mm thick) on G.I. slotted rails (1.6 mm thick) , Rail legs (2.5 mm thick) or with split clamps of approved make as per drawings to the satisfaction of the Project Manager.(For flush water supply only) 80 mm (based on 18.3.6)

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1 Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.11 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)

OD26603/2024-2025 80 X 80 cms (31" X 31") of approx ,upto 0.90 m depth, having 60 X 60 cms (24" X 24") self pigmented type double seal (air & water tight) DI manhole cover and frame (EHD) with closed bottom (not thru & thru) lifting key holes & load tested as per IS:1726 & BS EN:124. along with steps inside the manhole.

OD26604/2024-2025 120 X 90 cms (40" X 49") of approx 2.5 m depth, having 90 X 60 cms (36" X 24") self pigmented type double seal (air & water tight) DI manhole cover and frame (EHD) with closed bottom (not thru & thru) lifting key holes & load tested as per IS:1726 & BS EN:124. along with steps inside the manhole

OD26605/2024-2025 150cm X 150cm manhole for above 2.5 m depth having 90 X 60 cms (36" X 24") self pigmented type double seal (air & water tight) DI manhole cover and frame (EHD) with closed bottom (not thru & thru) lifting key holes & load tested as per IS:1726 & BS EN:124.

OD26606/2024-2025 120 X 90 cms of approx 1.5 m depth, self pigmented type double seal (air & water tight) DI manhole cover and frame (EHD) with closed bottom (not thru & thru) lifting key holes & load tested as per IS:1726 & BS EN:124.

OD26607/2024-2025 Supplying, Installing & Testing at site in position best quality PVC gully trap of size 160 X160 mm outlet embedded in plain cement concrete 1:4:8 (20mm metal), all the above encased in a chamber of 300 X 300 mm built with 15 cm thick RCC over a bed of CC 1:4:8 using 40mm size metal 100mm thick ,plastering with CM1:3,13mm thick inside, outside, exposed top surfaces and internal and top exposed surface finished smooth with a floating coat of neat cement, providing and fixing DI manhole cover and frame (MD) with closed bottom (not thru & thru) lifting key holes & load tested as per IS:1726 & BS EN:124 fixing the frame in PCC 1:2:4 using 20mm stone metal including painting the frame and cover with 2 coats of anticorrosive black bitumastic painting etc. complete all as specified and directed.

OD26608/2024-2025 Supplying, Installing & Testing at site in position best quality PVC gully trap of size 160 X160 mm outlet embedded in plain cement concrete 1:4:8 (20mm metal), all the above encased in a chamber of 300 X 300 mm built with 15 cm thick RCC over a bed of CC 1:4:8 using 40mm size metal 100mm thick ,plastering with CM1:3,13mm thick inside, outside, exposed top surfaces and internal and top exposed surface finished smooth with a floating coat of neat cement, providing and fixing DI manhole cover and frame (MD) with closed bottom (not thru & thru) lifting key holes & load tested as per IS:1726 & BS EN:124 fixing the frame in PCC 1:2:4 using 20mm stone metal including painting the frame and cover with 2 coats of anticorrosive black bitumastic painting etc. complete all as specified and directed. with self pigmented type double seal (air & water tight) DI manhole cover and frame of size 450 X 450 mm weighing not less than MD.

Miscellaneous items

OD31648/2024-2025 Supplying, Installing & Testing at site in position Fabricated UPVC SCH 40 Puddle flanges in the underground and overhead water tanks as per the drawings. 150mm OD

OD31647/2024-2025 Supplying, Installing & Testing at site in position Fabricated UPVC SCH 40 Puddle flanges in the underground and overhead water tanks as per the drawings. 100mm OD

OD31646/2024-2025 Supplying, Installing & Testing at site in position Fabricated UPVC SCH 40 Puddle flanges in the underground and overhead water tanks as per the drawings. 80mm OD

OD31645/2024-2025 Supplying, Installing & Testing at site in position Fabricated UPVC SCH 40 Puddle flanges in the underground and overhead water tanks as per the drawings. 65mm OD

OD31644/2024-2025 Supplying, Installing & Testing at site in position Fabricated UPVC SCH 40 Puddle flanges in the underground and overhead water tanks as per the drawings. 50mm OD

OD31643/2024-2025 Supplying, Installing & Testing at site in position Fabricated UPVC SCH 40 Puddle flanges in the underground and overhead water tanks as per the drawings. 40mm OD

OD31642/2024-2025 Supplying, Installing & Testing at site in position Fabricated UPVC SCH 40 Puddle flanges in the underground and overhead water tanks as per the drawings. 32mm OD

OD31655/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (IS:13592 & IS 4985) including injection moulded fittings with bosses where required eg tees, bends, clamps couplings and adapters & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete.and jointing with adhesive approved by manufactures including cutting and making good the walls or surface mounted with clamps as required at site (For AC Drain). 50 mm OD (6kg/cm2)(For shaft)

OD31656/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (IS:13592 & IS 4985) including injection moulded fittings with bosses where required eg tees, bends, clamps couplings and adapters & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete.and jointing with adhesive approved by manufactures including cutting and making good the walls or surface mounted with clamps as required at site (For AC Drain). 32 mm OD(10kg/cm2)- for AC drain (For ceiling)

OD31657/2024-2025 Supplying, Installing & Testing at site in position uPVC pipe (IS:13592 & IS 4985) including injection moulded fittings with bosses where required eg tees, bends, clamps couplings and adapters & clamping with Universal clamps, Anchor fastners(8mm), Threaded Rod(8mm), nuts, washers etc complete.and jointing with adhesive approved by manufactures including cutting and making good the walls or surface mounted with clamps as required at site (For AC Drain). 50 mm OD (10kg/cm2)- for FCU drain (For ceiling)

OD31708/2024-2025 Supply, installation & testing of Thermal Insulation of condensate drain piping using closed cell elastomeric nitrile rubber / closed cell cross linked polyethylene foam having a density of 50 +/- 10 Kg/m3 and with built-in vapor barrier, etc having 9 mm thickness .50 mm dia pipes

OD31709/2024-2025 Supply, installation & testing of Thermal Insulation of condensate drain piping using closed cell elastomeric nitrile rubber / closed cell cross linked polyethylene foam having a density of 50 +/- 10

OD31736/2024-2025 Supplying, Installing, Testing & Commissioning at site in position DI man hole load tested as per IS:1726 for under ground sump and over head tank. Load Bearing Capacity 600x600mm -Heavy Duty for UGS (HD) FOR STP

OD31737/2024-2025 Supplying, Installing, Testing & Commissioning at site in position DI man hole load tested as per IS:1726 for under ground sump and over head tank. Load Bearing Capacity 900x600mm -Heavy Duty for UGS (HD) FOR STP

OD31738/2024-2025 Supplying, Installing, Testing & Commissioning at site in position DI man hole load tested as per IS:1726 for under ground sump and over head tank. Load Bearing Capacity 600x600mm -Heavy Duty for UGS (EHD)

OD31739/2024-2025 Supplying, Installing, Testing & Commissioning at site in position DI man hole load tested as per IS:1726 for under ground sump and over head tank. Load Bearing Capacity 900x600mm -Heavy Duty for UGS (EHD)

OD31740/2024-2025 Supplying, Installing, Testing & Commissioning at site in position DI man hole load tested as per IS:1726 for under ground sump and over head tank. Load Bearing Capacity 600x600mm -Light Duty for OHT (LD)

OD31741/2024-2025 Supplying, Installing, Testing & Commissioning at site in position DI man hole load tested as per IS:1726 for under ground sump and over head tank. Load Bearing Capacity 600x600mm -Heavy Duty for UGS (EHD) COLLECTION PIT

OD31743/2024-2025 Supply & Laying connecting of cat-6, UTP cable through 25mm ISI rigid PVC conduit with medium grade and necessary fixing accessories as required for automatic level controller system.

OD31744/2024-2025 Supplying, Installing, Testing & Commissioning at site in position Water Saving Aerators for common area wash basin

OD31745/2024-2025 Supplying, Installing & Testing at site in position PDI certified Water Hammer Arrestor with copper body,Polypropylene piston, Brass Threaded Adapter, EPDM which is factory air charged and permanently sealed to operate on all plumbing lines at 10Kgf/cm2 complete in all respect.20 mm dia

OD31746/2024-2025 Supplying & Installing at site in position Roof Drain Doom model with CI body and aluminium ring.160 mm dia outlet

OD31747/2024-2025 Supplying & Installing at site in position Roof Drain Parapet model with CI body and Aluminium Grate. 160 mm dia outlet

OD31750/2024-2025 Supplying & Installing at site in position Roof Drain Parapet model with CI body and Aluminium Grate. 160 mm dia outlet

Point Wiring

1.10.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group A

1.10.2 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group B

1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.11 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

1.55.1 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A

1.55.2 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B

1.55.3 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

1.17.3 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.12 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.21 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.24.1 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.4 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.2 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.24.3 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.5 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

1.56 Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings)

1.57 Supplying & fixing suitable size Gl box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. lCD

1.27.1 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

OD32138/2024-2025 Supply, Installation, Testing and Commissioning of 200A 4 pole ATS (Automatic transfer switch) in the existing panel board with all control wiring with necessary equipments

OD32139/2024-2025 Supply, Installation, Testing and commissioning of 63A 4 pole ATS (Automatic Transfer Switch) in the existing panel board with necessary control wiring and other accessories.

OD32140/2024-2025 Supply, Installation, Testing and commissioning of 100A 4 pole ATS (Automatic Transfer Switch) in the existing panel board with necessary control wiring and other accessories.

OD32141/2024-2025 Supply, Installation, Testing and commissioning of 125A 4 pole ATS (Automatic Transfer Switch) in the existing panel board with necessary control wiring and other accessories.

MCB, DB and RCCB

90.11.1.11 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - three phase double cover (IP 42/43)

2.10.1 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

2.13.1 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.1 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

2.15.2 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.18 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth,metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

2.13.2 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.3 Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.3.2 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator8 way, Double door

2.12.1 Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.14.1 Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 amps

90.11.1.14 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.11.1.15 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+18) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

90.11.1.16 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required8 way (8+18) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/TP MCB as outgoing (IP 42/43)

90.11.1.19 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required6 way (8+12) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43)

OD32146/2024-2025 Supply, Installation, testing and commissioning of 40 A to 63 A, MCB (C curve), 10 kA breaking capacity Three pole/four pole with reputed brands.

2.10.4 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

90.14.8.12 1000 A, 4 pole, manual draw out type, microprocessor based ACB with overload , instantaneous SC , delayed SC and ground fault protection 50kA

90.14.10.1 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 16 kA (Ics=100%Icu), 3 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

90.14.10.4 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16 A-100A, 25/35 kA (Ics=100%Icu), 4 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

90.14.10.5 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.16A -100A, 35/36 kA (Ics=100%Icu), 3 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SC

90.14.10.6 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.125A, 35/36 kA (Ics=100%Icu), 3 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SC

90.14.10.8 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.200A, 35/36 kA (Ics=100%Icu), 3 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SC

90.14.10.15 Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.320A/400A, 50/55 kA (Ics=100%Icu), 3 pole, current limiting type MCCB with microprocessor based release with overload setting of 50 - 100% having adjustable OL & SC

2.2.5 Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.200 Amp, 25 KA,TPMCCB

2.2.10 Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.500 Amp, 35 KA,TPMCCB

2.2.14 Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.125 Amp, 36 KA

2.2.15 Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.200 Amp, 36 KA

2.2.8 Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.315 Amp., 35 KA,TPMCCB

2.10.5 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

Earthing

90.16.1.10 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.25 mm GI conductor (10 SWG)

90.16.3.8 Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)20 x 3 mm copper strip

90.16.5.3 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

OD32131/2024-2025 Earthing with G.I. earth plate 1200 mm X 1200 mm X 12.5 mm thick CI/GI including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 4 metre long etc. with charcoal/ coke and salt as required.

5.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Cable and Termination

90.12.40.33 Supply & laying of one No. PVC insulated and PVC sheathed armoured copper power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.4 core 10 sq mm

90.12.40.34 Supply & laying of one No. PVC insulated and PVC sheathed armoured copper power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.4 core 16 sq mm

90.12.41.33 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured copper power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp

90.12.41.34 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured copper power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp

9.1.32 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

90.12.6.27 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 25 sq mm

90.12.7.27 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 25 sq mm with factory made clamp

9.1.20 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

90.12.6.12 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3 core 4 sq mm

90.12.7.12 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3 core 4 sq mm with factory made clamp

9.1.2 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 10 sq. mm (19mm)

90.12.6.28 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 35 sq mm

90.12.6.29 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 50 sq mm

90.12.7.28 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 35 sq mm with factory made clamp

90.12.7.29 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 50 sq mm with factory made clamp

9.1.21 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.22 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 50 sq. mm (35mm)

90.12.5.41 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.4 core 16 sq mm

90.12.10.3 Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation63/50 mm or nearest size

90.12.6.39 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.4 core 6 sq mm

90.12.7.39 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 6 sq mm with factory made clamp

9.1.7 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 X 10 sq. mm (22mm)

90.12.6.31 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 95 sq mm

90.12.7.31 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 95 sq mm

9.1.24 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

90.12.5.27 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3.5 core 25 sq mm

90.12.10.4 Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation77/63 mm or nearest size

90.12.6.37 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 400 sq mm

90.12.6.32 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 120 sq mm

90.12.6.33 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 150 sq mm

90.12.6.34 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 185 sq mm

90.12.6.35 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 240 sq mm

90.12.6.36 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 300 sq mm

90.12.5.36 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3.5 core 300 sq mm

90.12.5.37 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3.5 core 400 sq mm

90.12.6.30 Supply & laying of one No. PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing masonry open duct as required.3.5 core 70 sq mm

9.1.23 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.25 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

9.1.26 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

9.1.27 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.29 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.30 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 300 sq. mm (70mm)

9.1.31 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 400 sq. mm (82mm)

Safety Equipments

OD32125/2024-2025 Charge for creating proper identification marks on the DB, TPN DB, VDB and panel board. as per the standards of KEI,KSEB,KSCADC

OD32126/2024-2025 Providing and Fixing of Electrical ISI Grade Rubber Mat suitable for 440Volts Switchboards.

OD32127/2024-2025 Supply and installation of fire bucket with stand

OD32128/2024-2025 S/F DCP fire extinguisher (5Kg): supply and installation of 5kg Dry chemical power type (DCP) fire extinguishers having ISI mark along with mounting supports etc.as required.

OD32129/2024-2025 Supply and providing Cable Route Marker

OD32130/2024-2025 Supply and fixing of 4.5 KG CO2 type fire extinguisher

Fittings

90.3.19.3 Supply conveyance, installation, testing and commissioning the light fittings of following types made from CRCA sheet 0.5mm thickness with all accessories and lamps directly on wall and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required1200 mm 1X20W LED Lamp with box type fixture

OD32132/2024-2025 Supply, Installation, Testing and Commissioning of 20 W LED round/Square surface or recessed down light with cool or warm light with standard accessories for fixing in the wall, ceiling, ACP, or other as per site condition. (Reputed brands LED down light, Brand approved by the Engineer incharge)

OD32133/2024-2025 Supply, installation, testing and commissioning of exhaust fan in the existing opening making good damage, connection, testing, commissioning etc. as required. (a) 230 mm metal body (Make:- reputed brands or brand approved by the site engineer- light duty)

OD32134/2024-2025 Supply, Installation, Testing and Commissioning of heavy duty exhaust fan

OD32135/2024-2025 Supply, Installation, Testing and commissioning of 1200 mm sweep ceiling fan (BLDC), 5 star rated with minimum 3 year on site replacement warranty suitable to work with regulator. The rate inclusive of 2 MD type fan regulator and 30 cm down rod of standard accessories and wiring. The fan should deliver 230 cm m air delivery capacity, 370 RPM speed. (Kulirma Josh or equivalent make)

Cable Tray

4.1.1 Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.100 mm width X 50 mm depth X 1.6 mm thickness

4.1.3 Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.225 mm width X 50 mm depth X 1.6 mm thickness

4.1.4 Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

4.1.6 Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.450 mm width X50 mm depth X 2.0 mm thickness

4.1.7 Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.600 mm width X 50 mm depth X 2.0 mm thickness

Panel Board

90.14.1.2 Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame)

90.14.2.1 Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

90.14.2.3 Supply and providing 4mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

90.14.3.2 Supply and providing heavy duty 'A' section neoprene gasket in the panel boardU' section rubber beeding suitable for 1.60/ 2.00 mm sheet

90.14.4 Supply and fabrication conveyance and installation of base frame of panel board using 75 x 40 mm rolled steel channel (ISMC)

90.14.5 Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

90.14.6 Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required.

90.14.7 Supply and providing copper earth bus in the panel board

OD32136/2024-2025 Supply, Installation of Digital Multi Function Meter (MFM) for monitoring the current, voltage and frequency etc, of the circuit in the existing panel board. with all necessary equipment's like CT and others.

OD32137/2024-2025 Supply, installation and commissioning of LED indicator light in the existing panel board of all respective color for EB/ DG supply indication, with necessary control wiring

HT work

OD32147/2024-2025 Supply, Erection, Installation, Testing and Commissioning of 11KV/433V, 630 KVA Indoor Dry type Cast resin type copper wound Air natural cooled Unitised Sub Station-Indoor-with VCB Panel-11 kv-630 kVA. Cast resin Transformer with offcircuit tappings from +5% to -10% in steps of 2.5%, changeable by tap links provided, with LT cable box with LT CT and NCT and HV terminals connected to 11KV, 26.3A, 630A VCB panel power pack with incoming suitable for XLPE cable and output connected to 11KV seal off bushing to the transformer. Type:TRP

OD32148/2024-2025 Supply, Erection, Testing and Commissioning of 11 KV, 630A, 21 KA Ring main unit as per KSEB specifications. 12 kV, SF6 Ring Main Unit complete MakeSchneider( HSN Code; 8537 ) one side (Extensible, Outdoor-(2 Isolator+1Breakers+FRTUFBX-E/12-20/CCT2+FRTU/Outdoor – Motorized+ Battery Charger.

OD32149/2024-2025 Supply, Erection, Testing and Commissioning of HT Multi Panel-11KV-IndoorVCBP-VCBMP-VCBP (HT Multi panel )with all standards to meet the KSEB and KSEI norms. Incomer : VCB Panel, Outgoing(1) : VCB Panel, Outgoing (2): VCBM Panel.

8.1.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 120 sq. mm and upto 400 sq. mm

8.4.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required.Above 120 sq. mm and upto 400 sq. mm

10.4.3 Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:240 sq. mm

10.4.4 Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:300 sq. mm

10.5.3 Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :240 sq. mm

10.5.4 Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :300 sq. mm

OD32150/2024-2025 Supplying of 11 KV HT Aluminium conductor XLPE insulation steel strip armoured PVC outer sheath (A2XFY) cable of size 3 core 300 sqmm

OD32151/2024-2025 Supplying of 11 KV HT Aluminium conductor XLPE insulation steel strip armoured PVC outer sheath (A2XFY) cable of size 3 core 240 sqmm

Lift work

OD32104/2024-2025 Supply, Erection, Testing and Commissioning of 20 (1360KG) passenger/ Bed (ICU Bed size) Machine room less (gearless) lift, with a speed of 1 m/s, Having SS (304) grade Hairline Finish material cabin and doors with 1000mm centre opening or 1200 mm automatic opening (Telescopic) with advance Door drive system. Normal travel height with G+3 Opening (four). The lift should have all modern features and facilities like Automatic Rescue Device (ARD), Overload Protective Device (OPD), Correction drive to next level, Emergency Alarm @ Main Floor, Car Call backwards, Overload function, constant indication/Buzzer, Bypass load Function, Auto Cut off Fan and Light, Manual Rescue Operation & Centralized Hoisting for lesser vibration and smooth travel, Pit Ladder, Micro movement Led Based Buttons, L.W.D. (Load Weighing Device), Direction & Position Indicator In Car & Landing, Advanced Car Position Indication, Automatic Brake Test function every 11hours<br>Every run brake supervision, Phase reversal functioning, Signal Fixtures, +10% to –10% Voltage Fluctuation Withstanding Capacity, & Door Close Button, Door Open Button, Car Emergency Light, Fireman Drive, Curtain of Light 169 Beams, Accurate Relevelling, Automatic, Closed Door, Panel Board and other device for the operation of lift and other necessary items as per the Kerala state electrical inspectorate standards. LED ceiling light in the SS false ceiling with fan, communication device like intercom etc. The rate inclusive of cabling from the existing panel board to lift panel board and The rate inclusive of approval charges from electrical inspectorate. (Approved Make : ATLAS, Jhonson, Infra )

16.12.2.4 Supply, Installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, etc as per approved drawings and specifications of following sheet thickness complete as required.Site fabricated GSS sheet metal rectangular ducting as per IS 655-2006 for 1.25 mm thick

2 16.12.1.1 Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 Thickness 0.63 mm sheet

16.12.1.2 Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 Thickness 0.80 mm sheet

16.12.1.3 Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006 Thickness 1.00 mm sheet

16.12.1.4 Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006 Thickness 1.25 mm sheet

16.19.1 Supplying, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regulator interval as per site requirement etc. complete as required as per specifications.Thermal insulated flexible duct (200 mm dia)

16.23.1 Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class "O") insulation on existing duct after applying two coats of cold setting adhesive (CPRX compound). The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.Nitrile rubber insulation - 25 mm

16.23.2 Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class "O") insulation on existing duct after applying two coats of cold setting adhesive (CPRX compound). The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.Nitrille rubber insulation - 25 mm

16.22.1 Supplying, fixing acoustic lining on wall and celling of AHU rooms with 50 mm thick, density 32 kg/cu.m resin bonded glass fiber insulation friction fixed in 610 mm x 610 mm frame work made of 25x50x50x50x25xmm made out of 0.6 mm thick GI sheet U shaped channel and covered with reinforced fiber glass tissues and finished with0.80 mm perforated aluminum sheet etc. complete as required and as per specifications.50 mm thick resin bonded glass wool having density of 32 kg/cum

16.13 Supply, Insulation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. GI volume control duct damper

16.20.1 Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/ main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.Fire damper

16.20.2 Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/ main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.Actuator

16.16.a Supplying and Fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

16.18 Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminum without volume control dampers with anti smudge ring and removable core.

16.15 Suppluying and Fixing of powder costed extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

16.17 Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminum with aluminum volume control dampers with anti smudge ring and removable core.

OD32107/2024-2025 Supply, installation and testing of GSS, factory fabricated Round/Spiral ducts,120GSM Zinc coated, complete with necessary flanges as specified in the technical specification, necessary supports using thread roads and anchor bolts, supply air collars, vanes, splitters dampers duly painting of the ducts as per specification and as specified by the consultant/owner using 22 or 24 SWG . Note : No additional rates for wastage

OD32108/2024-2025 Supply, installation and testing of Acoustic Insulation of ducts using open cell processed elastomeric nitrile rubber having a density of 150 +/- 10 Kg/m3. The insulation should have Built-in Anti-Microbial Product Protection, and should pass Fungi Resistance as per ASTM G 21 and Bacterial Resistance as per ASTM E 2180.

OD32109/2024-2025 Supply, installation, testing and commissioning of GI powder coated round butterfly damper Frame Thickness shall be1.2mm, & Blade thickness to be 1mm of size with opposed blade and PVC gears for smooth operation of air volume control.

OD32110/2024-2025 Supply, installation, testing and commissioning of extruded Aluminium profile, anti corrosive, jet diffuser with control damper. Emblazon shall be as per architect's/client's advise

OD32114/2024-2025 "Supply, Installation, Testing and Commissioning of Inverter type DX Condensing unit with AHU Kit, Expansion Valve & Filter Drier 400/440V, 50/60Hz, Three phase, comprised of scroll driven compressor, condenser coil, low noise condenser fan, fan guard, motor protection, supporting stands, vibration isolators etc. Refrigerant shall be R410 A Unit shall be supplied with corded remote controller with LED/LCD display information. COP of the unit shall be > 3.5 " 11 TR

OD32116/2024-2025 Supply, Installation, Testing and Commissioning of Inverter type DX Condensing unit with AHU Kit, Expansion Valve & Filter Drier 400/440V, 50/60Hz, Three phase, comprised of scroll driven compressor, condenser coil, low noise condenser fan, fan guard, motor protection, supporting stands, vibration isolators etc. Refrigerant shall be R410 A Unit shall be supplied with corded remote controller with LED/LCD display information. COP of the unit shall be > 3.5

OD32118/2024-2025 Supply, Installation, Testing and commissioning of 25mm thick mineral wool insulated Double Skin Inline Exhaust. Outer skin shall be 0.8 mm pre plasticized or powder coated GSS sheet. Inner sheet shall be 0.8 mm plain GSS perforated. Extruded Aluminum corners. Complete with motor guard, cable entry, GSS base frame. Screw less construction with zero leakage in the panel joints. Inspection door for all the sections. Necessary MS Support with Two coats of epoxy primer and 1 coat epoxy painting to be considered where unit located outdoor. Fan: PLUG TYPE , IE - 3, Motor shall be suitable for Variable Frequency Drive along with spring Isolators and 415±10% volts, 3 phase AC supply, Frequency range shall be 10% to 100%. 3 phase AC supply with suitable Armored cable from starter panel to motor up to 7m including glanding at both ends through a local isolator near equipment. The harmonic levels in the VFD shall not exceed the the limits specified in IEEE 519 Standards. The Contractor shall submit the ESP calculation as per the site condition for approval. of AFR : 3040/3600 CFM, ESP : 300/200 Pa.

OD32119/2024-2025 Supply, Installation, Testing and commissioning of 25mm thick mineral wool insulated Double Skin Inline exhaust/fresh air fans. Outer skin shall be 0.8 mm pre plasticized or powder coated GSS sheet. Inner sheet shall be 0.8 mm plain GSS perforated. Extruded Aluminum corners. Complete with Glass view panel, motor guard, marine light, limit switch, cable entry, GSS base frame. Screw less construction with zero leakage in the panel joints. Inspection door for all the sections. Necessary MS Support with Two coats of epoxy primer and 1 coat epoxy painting to be considered where unit located outdoor. 1 phase AC supply with regulator for speed adjustment. The Contractor shall submit the ESP calculation as per the site condition for approval. with starter panel and other necessary equipment. of AFR : 700/950/1230/1280/1735 CFM, ESP : 200 Pa

OD32123/2024-2025 Supply , installation, testing and commissioning of ceiling suspended multi-speed jet fans with Al aero foil propeller, galvanized steel sheet casing, noise arrestors, inlet and outlet guards, IP 55 class H motor protection, tested according to EN 12101-3 300 DEG C for minimum 2 hours, complete in all aspects conforming to the technical specifications. with necessary equipment

OD32162/2024-2025 Supply, installation, testing and commissioning of seamless hard drawn Copper piping for following units duly insulated with 13 mm thick nitrile rubber insulation for gas line and liquid line, along with communication cabling through PVC conduit. Refrigeration piping to be taken in the piping rack / support individually connecting to all indoor units. Even necessary supports, fittings, valves & where ever required will be included. Outdoor piping shall be with polyshield coating and installed in a PVC pipe and ensure that refrigerant lines are weather protected with Foster mastic sealent or equivalent. of size 15.99mm

OD32163/2024-2025 Supply, installation, testing and commissioning of seamless hard drawn Copper piping for following units duly insulated with 13 mm thick nitrile rubber insulation for gas line and liquid line, along with communication cabling through PVC conduit. Refrigeration piping to be taken in the piping rack / support individually connecting to all indoor units. Even necessary supports, fittings, valves & where ever required will be included. Outdoor piping shall be with polyshield coating and installed in a PVC pipe and ensure that refrigerant lines are weather protected with Foster mastic sealent or equivalent.

OD32167/2024-2025 Supply, transportation, and fixing in position of rigid PVC (10 kg/sq.cm) condensate drain water piping with necessary supports and fittings like, U-traps, elbows, tees and reducers insulated with 9mm nitrile rubber and BOPP tape. 32 mm dia

Fire Alarm

17.1.1 FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning of heat detector operating at 54ºC / 57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.

17.1.2 FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning of smoke detector with built-in LED and mounting base complete with all connections etc. as required.

17.1.3 FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning of manual call boxes of MS Construction in surface/recess with stainless steel chain & hammer assembly Complete with glass and push button etc. as required

17.1.4 FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning of manual call box of ABS type in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

17.1.5 FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning response indicator on surface/ recess MS box having two LEDs metallic cover complete with all connections etc. as required.

17.1.6 FIRE DETECTION AND ALARM SYSTEM (CONVENTIONAL)Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required

17.5.2 CABLING & WIRINGSupplying & laying of 2x1.5 sq mm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

17.5.3.1 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.speaker cable Single pair, 2-core, 1.5 sq mm

17.5.4 Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.21.4 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.40 mm

90.14.28.7 S & F Motor starters of the following ratingsFully automatic star delta starter for 25HP motor

90.17.1.9 Electric driven Main Fire Pump: Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads.1620 lpm at 56 m Head

OD32142/2024-2025 Preparation of drawings/ schemes/ documents and getting final approval/ sanction/ NOC from statutory departments viz. Fire Force Department, Tvm etc. as per rules and regulations (statutory fees if any will be borne by the owner) & AMC charges for three years after DLP to be considered.

OD32143/2024-2025 Supplying and installing in position self glowing "FIRE EXTINGUISHER" and " MANUAL CALL POINT" sign boards of size (150 X 150 mm) made of luminescent safely, rigid sheet in green colour, photo luminescent ACP sheet in protective glass with two hanging chains & necessary supports to hang it on ceiling. Samples has to approved by the Architect before procuring the same.

OD32144/2024-2025 Supplying and installing in position self glowing "FIRE LIFT" and "FIRE ASSEMBLY POINT" sign boards of size (150 X 300 mm) made of luminescent safely, rigid sheet in green colour, photo luminescent ACP sheet in protective glass with two hanging chains & necessary supports to hang it on ceiling. Samples has to approved by the Architect before procuring the same.

OD32145/2024-2025 Supplying and installing in position self glowing "FIRE EXIT", "FIRE EXIST in stair case (up, down, left and right) sign boards of size (150 X 400 mm) made of luminescent safely, rigid sheet in green colour, photo luminescent ACP sheet in protective glass with two hanging chains & necessary supports to hang it on ceiling. Samples has to approved by the Architect before procuring the same.

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY (BID ID -1992006)

MARYMATHA INFRASTRUCTURE PVT LTD (BID ID -1992282)

Bidder Name

THE URALUNGAL LABOUR CONTRACT CO-OPERATIVE SOCIETY

MARYMATHA INFRASTRUCTURE PVT LTD

V P M PROJECTS