CA NO CWE / HILLS /EWS/49 OF 2021-2022 ADDN/ ALTN TO CERTAIN OTM BLDGS AT HARSIL UNDER GE 871 EWS

Amount

Taking down chowkats or frames exc 1.50 sqm but n.exc 4.00sqm eachwith shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames n.exc 1.50 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specfied and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in unframed work complete all as specified and directed.

Dismantling of framed timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

M&L for bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F 35mm thick factory made glazed and skeleton shutters in 2nd class hardwood, open rebated and prepared to receive glass, gauze, etc. divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with particle board core and plywood face panesls, commercial type on bothe sides complete all as specified and directed.

M&L for preparation of new or previouly untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 100 mm long butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with haps, staple (bolt type) and fixing clips with sheet, cast and extruded section and fixing bolt and sliding bolt of extuded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F steel windows with side hung shutters including box type hinge with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded and making good disturbed surface as per existing surface complete all as specified and directed.

S&F steel windows with side hung shutters including box type hinge with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded and making good disturbed surface as per existing surface complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars barred iron doors, ladders, framed balusters, wlak ways, railings, fram work of water tanks and similar work etc complete conforming to Fe 290-0 grade-E-165 complete all as specified and directed.

S&F sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares n exc 0.5 Sqm in each pane complete all as specfied and directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

M&L for preparation of new steel surfaces any description, over 10cm in width or girth,not otherwise applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shspe required incl cranking, bending spirally for hooping for coloumns, hooking ends andbionding with (annealed) not less than 0.90 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over and including 10mm dia in stirrups, spacers and binders, bent to shspe required incl cranking, bending spirally for hooping for coloumns, hooking ends andbionding with (annealed) not less than 0.90 mm dia complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams, drain sides or similar works vertical or to batter for rough finished surface of concrete in flat complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat concrete surfaces complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges rough finished surface of concrete in flat complete all as specified and directed.

M&L for M-25 (20mm graded aggregates) reinforced cement concrete (design mix) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for M-25 (20mm graded aggregates) reinforced cement concrete (design mix) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for M-25 (20mm graded aggregates) reinforced cement concrete (design mix) as in Chajjas complete all as specified and directed.

M&L for providing cement concrete type B1 1:2:4 using 20 mm graded aggregate, as in coping including necessary form work complete all as specified and directed.

Excavating in trenchs, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in any type soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks type C1 1:3:6 (20 mm graded aggregate) exc 10 cm width and setting in cement mortar 1:4 complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks type C1 1:3:6 (20 mm graded aggregate) exc 10 cm width and setting in cement mortar 1:6 complete all as specified and directed.

Returning, filling including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil all as specified and directed.

Removing excavated material (soil) exc 250 mtr but n exc 500 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surfaces using WPC and finishing the surface even and smooth without using extra cement complete all as specified and directed. NOTE -WPC shall be measured and paid separetely.

M&L for preparation of newly plastered wall surfaces and applying two coats oil bound distemper over a coat of primer including making the surface truly smooth by a coat of wall putty complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

S&F in repair power coated decorative type mild steel curtain rods 32 mm dia including a pair of brackets for each curtain rod supplied and fixed including drilling holees/ plugging to wall etc, with PVC rawl plugs/ wooden gutties complete all as specified and directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F of false ceiling of everest designer boards of size 595 x 595 x 4 mm thick fixed on GI snap grid complete all as specified and directed.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for sand filling under floors including spreading, levelling and well ramming, watering and consolidation complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40 mm stone aggregate) as in sub base of PCC floor finished even and rough complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (12.5mm graded stone aggregate) as in floor finishing even and rough to receive floor finishes complete all as specified and directed.

M&L Non-skid joint free coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C2 using 40 mm aggregate in plinth protection including finishing even and smooth without using extra cement complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint treating ends of posts, backs of chowkats, etc., area tarred exc 0.1 sq. m but n exc 0.5 sq. m each complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area n exc 0.1 sq. m each complete all as specified and directed.

Surface dressing not exc 15 cm deep in hard /dense soil complete all as specified and directed.

M&L for hard core of broken stone or boulders gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface of broken bricks aggregate complete all as specified and directed.

M&l for chequered cement concrete tiles 20cm x 20cm x 25mm/30cmx30cmx25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment including 20 thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

Removing excavated material (soil) not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

E/M Portion:- Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc and making good disturbed surfaces of wall, roof etc to match with existing surface complete all as specified and directed.

M&L for point wiring for one light/ bell/ fan point controlled by one, one way switch with 1.5 Sqmm size, PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) PVC cable drawn into & including medium grade PVC conduit (not less than 20mm outer dia) with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/colouring the external surface and matching the same with existing surface) and sunk cast iron or pressed steel terminal boxes for mounting fittings like switches, sockets & fan regulators etc with 3 mm thick plastic laminated sheet covers fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.5 Sqmm multistranded copper conductor cable earth wire and connected to earth dolly complete all as specified and directed.

All as per item No.65 herein before but one 3 pin socket outlet 5 Amps independent board controlled by one, one way switch.

All as per item No.65 herein before but one 3 pin socket outlet 5 Amps on the same board.

All as per item No. 65 above but with 4 Sqmm two single core and 2.5 Sqmm one single core as earth wire for 15/16 Amps socket out let, 3 pin on independent board.

S&F switch piano flush type single pole, one way 5/6 Amp complete all as specified and directed.

Fixing only switch piano flush type single pole, one way 5/6 Amp complete all as specified and directed.

S&F switch piano, flush type single pole 15/16 Amp complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin, 5/6 Amp flush type complete all as specified and directed.

Fixing only socket outlet 2 in 1, 3 pin, 5/6 Amp flush type complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin, 5/6 and 15/16 Amp flush type complete all as specified and directed.

S&F ceiling rose surface bakelite 2/3 terminal 65 x 25 mm dia poly carbonate isolated with base plate complete all as specified and directed.

Fixing only ceiling rose surface bakelite 2/3 terminal 65 x 25 mm dia poly carbonate isolated with base plate complete all as specified and directed.

S&F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed.

S&F LED Bulb 10 Watt, cool day light 230/240V AC supply complete all as specified and directed.

S&F LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core 23/0.0076 flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core 23/0.0076 flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED bulkhead light fitting 10W luminaires including LED driver holder connceting up with three core flexible copper conductor cable sutaible size complete all as specified and directed.

S&F in replacement building security light fitting complete with 35 watt LED type IP 66 pressure die cast aluminium housing and heat resistance toughened glass with frame protection and better optics for uniform distribution etc complete with twin core copper conductor cable 1.5 sqmm from ceiling rose to fittings complete all as specified and directed.

Dismantling and taking down of unserviceable distribution boards and change over switch any type complete all as specified and directed.

S&F sheet metal enclosure for DBs double door type single pole and neutral 8 way including blanking plate as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed.

Dismantling and taking down of unserviceable MCBs any type any capacity complete all as specified and directed.

S&F MCB SP with thermal over load as well as magnetic short circuit tripping device quick, break trip free mechanism, robust design and terminals having heat resistance moulding suitbale for single phase circuit of 6 to 40 Amps complete all as specified and directed.

S&F MCB SPN with thermal over load as well as magnetic short circuit tripping device quick, break trip free mechanism, robust design and terminals having heat resistance moulding suitbale for single phase circuit of 63 Amps, 240 volts complete all as specified and directed.

S&F in repair 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, with two single core cable 10 sqmm solid conductor complete all as specified and directed.

M&L in replacement of earthing complete with galvanised steel earth plate electrode 600 x 600 x 6mm thick, buried directly in ground vertically to a earth pit not less than 2.25 metres deep below ground level with top edge of the plate not less than 1.5 metres below normal ground level, connected to and including galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron and connected to test point all s shown in electrical plate No. 3 of SSR Part-I 2009 and as specified or indicated and testing on completion including excavation and earth work in any type of strata available at site, PCC (1:3:6) type C1 earthing chamber pre cast RCC slab 50mm thick in cement concrete 1:2:4 type B1 using 20mm graded aggregate reinforced with welded steel wire fabric (XRM) weight not less than 4 Kg/Sqm funnel with GI watering pipe of 20 mm bore meduim grade, wire mesh and lugs, GI protection pipe of 15mm bore light grade up to 7.50 mtr long etc complete all as specified and directed Note:- GI earth wire and protection pipe beyond 7.50 mtr will be measured and paid separately)

Surendra Engineers

M/s J P Traders

Prem singh kuwarbi and co