Building Work

Repairing and renovation of Stamp Duty Office at 3rd floor collector office Kaliyawadi ,Di.Navsari

BILL OF QUANTITIES

Percentage Rate Tender

Item Description of Item Quantity Unit Rate In Amount

1 Providing and Fixing Decorative Composite Half partiton 27.00 Sqm 3199.68

of wooden, glass and gap as per drawing or as directed by

engineer-in-Charge, Using 8 mm thick ISI marked Ply on

both side fixed on a teakwood framing grid of teakwood

member Size 65 mm x 38 mm at 450 mm C/C on Vertical

side and on horizontal side as per design or as directed by

Engineer -in -Charge. Wooden portion consists of both

side 12 mm thick ply with 1 mm thick lamination on

outer side of ply Colour & Design of Lamination is as per

Drawing or as directed by Engineer-in-Charge. Glass

portion consist of 5 mm thick toughned glass with

wooden framing. . Rates includes all Labour, Material,

Screw, Khilli, Fevicol, PU finish on outer side of ply

including all taxes Etc. complete. All Material to be used as

approved by Engineer-in-Charge.

2 Providing and Fixing Wooden Partiton Using 8 mm thick 32.67 Sqmt 3879.41

ISI marked Ply on both side fixed on a teakwood framing

grid of teakwood member Size 65 mm x 38 mm at

mm C/C on Vertical side and on horizontal side as per

design or as directed by Engineer -in -Charge. Wooden

portion consists of both side 12 mm thick ply with 1 mm

thick lamination on outer side of ply Colour & Design of

Lamination is as per Drawing or as directed by Engineer-

in-Charge.. The Partion also includes door When

necessary as per drawing by using 8mm ply on both side

with 1 mm thick lamination including frame of

25mmx75mm included,beading on outer side, good

quality door closer, godrej lock, SS hinges etc. Rates

includes all Labour, Material, Screw, Khilli, Fevicol, PU

finish on outer side of ply including all taxes Etc.

complete. All Material to be used as approved by Engineer-

Item Description of Item Quantity Unit Rate In Amount

3 Providing and Arranging CLERK TABLE Overall Size : (L) 4.00 No. 9266.75

1200 X (W) 600 (H) 750 mm.TABLE TOP : 25mm THK. ISI

Marked Pre Laminated MDF Board IS-14587-1998. With

up to date amendment. LIPPING : Teak wood half round

50mm wide, supported from inside by Jungle wood

mm x 25 mm. PANNEL : Two folded edge CR sheet

0.80mm thick Confirming to IS-513. DRAWER BOX : CR

sheet 0.80mm thick Confirming to IS-513. CUBOARD size

600(D) x 350(W) x 450mm(H). DRAWER SIZE :

500(L)X100mm(D) Minimum. (3 Nos) FRAME &

STRUCTRUE : ERW Square pipe 25x25x1.25mm in

size1375(L) x 750(W) x 732(H)mm. as per Diagram

CUPBOARD SHUTTER : BOX TYPE made of 0.80mm CR

sheet Confirming to IS-513. FOOT REST : ERW square

pipe 25x25x1.25mm in full length and gap between two

pipes approx. 85.mm Including all materials and labours

etc. complete as per drawing and instruction of Engineer-

4 Providing and Arranging EXECUTIVE CHAIR Overall size : 4.00 No. 11170.60

Width 650mm Without castors, Depth 650mm, Height

1050 to 1140mm, Adjustability of seat height 440 to

530mm. Seat size : 500x500mm approx. Back size :

500x610 (H) approx. Material : Seat and back should be

made up of 12mm thick hot pressed plywood upholstered

with fabric and molded Polyurethane foam (60mm thick.

With density 50-55), together with molded ABS seat and

back covers. The back foam is designed with contoured

lumbar support for extra comfort. The armrest should be

one piece and made of black integral sikin polyurethane

and reinforced with MS insert and scratch and weather

resistant. Castors : The twin wheel castors should be

injected molded in black Nylon. Pedestal Assy. : The

pedestal should be injection mounded in black 30% glass

filled Nylon with gas lift mechanism. Upholstery : The

seats and backs are to be covered with superior quality

fabric. Finish : All steel components are to be painted

after proper anti corrosion pretreatment of surface

Including all materials and labour etc. complete as per

drawing and instruction of engineer-in-charge.

5 Providing and Arranging VISITOR CHAIR Overall Size: 10.00 No. 3292.60

(W) 500 x (D) 550 x (H) 820 mm with P type handle, Non

revolving oval shape with metal steel powder quoted

visitor chair Including all materials and labours etc.

complete as per drawing and instruction of Engineer-in

6 Provinding & supplying of Stainless Steel Chair (three 3.00 No 7676.00

seater) made out totally of S.S. pipe/ sheets as approved

or directed by the architect and approved by the Engineer

Item Description of Item Quantity Unit Rate In Amount

7 Providing and fixing eco-friendly light weight calcium silicate false 71.06 Sqm 1648.96

ceiling tiles having Tegular edge & 15 mm Thick Densified edges on

the Tile Periphery for Extra Strength The Light weight calcium silicate

ceiling tiles shall have , light reflection 85% noncombustible as per

B.S. 476 part IV, 100% humidity resistance and also having thermal

conductivity0.043° w/m KC.for the best thermal Insulation . The Light

weight calcium Silicate tile shall be of approved texture Fine fissured/

Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value

of 0.75 NRC or equivalent of size 595 X 595 mm to be laid on true

horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including

both side) consisting of main ‘T’ runner suitably spaced at joints to get

required length and size of 24X38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size

24X28mm made out of 0.33mm (Minimum) sheet spaced 1200mm

along spaced between main ‘T’ at 600mm centre to centre to form

agrid of 1200X600mm and secondary cross ’T’ of length 600mm and

size 24x28mm made of 0.30 mm thick (Minimum) sheet to be

interlocked at middle of the 1200X600mm panel to form grid of size

600X600mm resting on periphery walls/partitions on a perimeter

wall angle pre-coated steel of size (24X24X3000mm made of 0.40mm

thick (minimum) sheet with the help of rawl plugs at 450mm centre to

centre with 25mm long dry wall screws @ 230mm interval and laying

15mm thick Densified edges light weight calcium silicate ceiling tiles

of approved texture (Fine Fissured/Cosmos/Spintone) in the grid

including, cutting /making opening for services like diffusers, grills,

light fittings, fixtures, smoke detectors etc., wherever required, Main

‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size

25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash

fasteners, 4mm G.I. adjustable rods with galvanized steel level clips of

size 85X30X0.8mm, spaced at 1200mm centre to centre long main ‘T’

bottom exposed with 24mm of all T-sections shall be pre-painted with

polyester baked paint, for all heights, as per specifications, drawings

and as directed by engineer-incharge.Note:- Only calcium silicate

8 Applying two coats of (white cement based) or (acrylic 83.08 Sqm 40.59

lappy (putty)) or equivalent and two coats of primer of

approved brand and manufacture on new wall surface to

give an even shade including thoroughly brushing the

surface free from mortar dropping and other foreign

matter and sand papered smooth. for All floor.

9 Wall and Ceiling painting (two coats) with plastic 197.01 Sqm 81.31

emulsion paint of approved brand and manufacture on

undecorated wall and ceiling and slopping roofs surface

to give an even shade including throughly brushing the

surface free from mortar droppings and other foreign

matter and sand papered smooth.

10 Providing and fixing 15mm-18 mm thick Polished 32.27 Sqm 1579.64

Marble with full round edge and double side polished of

any required and fixing with 12 mm (av.) thick bases of

cement mortar 1:3 (1-cement : 3-coarse sand) & adhesive

including All exposed edges cut and Smooth Finished as

directed by engineering in charge etc. complete.

Item Description of Item Quantity Unit Rate In Amount

11 Providing & fixing Cupboard shutter having 25mm thick 25.75 Sqm 3717.81

block board & including with frame 25 mm x 50 mm size

as directed etc. complete including necessary both side

lamination 1 mm thick outer side & 0.80mm thick inner

side fixing by necessary 6" SS hinges, 8" handles, magnet,

stoppers, etc. as directed including fevicol, and other

hardware material required. Plywood and all fixture shall

be of ISI quality and as approved by engineer-in-charge

including cost of teak wood beading, one coat of primer

and two coats of oil painting or polishing as directed.

12 Providing & Supplying ANGLE IRON RACK having Size- 5.00 No 16362.00

2000mm (H) x 900mm (L) x 600mm (W). The over all

design & appearance of this Angle iron rack shall be as

shown in fig. Angle iron 35x35x2.5/3.00 mm min. thick or

alternately slotted angle or same size 35x35x2mm can be

used Joints in angle iron shall not be allowed. Each shelf

shall be made from CR sheet. Shelf shall be formed such

that lengthwise edges are bent two times at right angles.

First bend shall be 30mm & second bend 8mm.

Widthwise edges are to be bent only one time. Press cut

shelf corner plate’s 8nos. in upper shelf and 8no. in lower

shelf, of 0.80 mm thick CR sheet. Galvanized nut both of

hexagonal hand 8mm dia x 10mm long. Bolting & pressing

where ever required. No sharp edges on angle iron ends

shall be allowed, four plastic shoes of appropriate size

shall be provided for legs. No. Minus tolerance is allowed

in angle iron thickness. The quoting price should be

inclusive of all types of taxes & duties packing,

forwarding, loading, unloading, installaion. Supplied

strictly as per our technical specifications and make. As

per the direction of the Architect / Engineer In charge.

13 Providing and Fixing Impulse Blackout Roller Blinds with 12.00 Sqm 1767.50

fabric of 0.53mm thickness and Top channel of non-

rusting aluminium alloy with 1.25mm thickness and

bottom channel of 1.50mm thickness & 21mm diameter.

Tilt channel of ABS plastic with 1.50mm polyster

Item Description of Item Quantity Unit Rate In Amount

14 Providing and Arranging CUPBOARD (WARDROBE) Size: 5.00 NO 11665.50

900mm x 450mm x 2130mm (H). The CR Sheet used shall

be of prime quality, Confirming to IS-513 and thickness

1.0 MM. Each shelf be formed such the edges are bend

two times at right angle, first bend 30mm and second

bend 8mm. Door stiffener frame inside to its full height in

top hat section size 100mm width. Lever rod shall be of

Ms 12mm round/square bar , or 10mm bright bar. Size of

hinges shall be 75mm length x 1.6mm thk. Brackets shall

be made of 1.6 mm of CR sheet, riveted or bolted on each

side of hinges. Machine made lever plate (patla)with

brass bush of good quality or machine made six lever type

patla. Patla shall be covered by box covered by box over

fitted with round head screws. For locking brass body

Godrej type cabinet lock or cabinet lock 6leaver die cast

zinc alloy body of size(h) 65 x (W) 50mm fitted on four

screws or “ GRACE” LOCK. Keys in duplicate with key

rings shall provided. Metallic key cover electroplated

nickel/chrome on front side of the door shall be provided.

For door, die cast chrome plated handle fitted with

washer and double nut. Leg height shall be 125 mm x

mm. Including all materials and labour etc. complete as

per drawing and instruction of engineer-in-charge.

15 Supplying and fixing Notice board made from teak wood 2.00 No 4787.40

size of board is 2.40 x 1.80 x 0.05 with 3mm plain glass

door including thrmocole coted inner side with wellvet

cloth upper side also including backside 9mm thick

allproof ply and polishing including necessary handles

locking arrgnte ment as directed by engineer-in-charge.

16 Providing and fixing Roller blinds of Imported Fabrics as 12.00 Sqm 1794.77

per approved shade and matching head rail with all

accessories , material & labour etc. complete.

17 Painting one coats (excluding priming coat) on previously 14.00 Sqm 86.42

painted steel and other metal surface with enamel paint,

brushing to give an even shade including cleaning the

surface of all dirt, dust and other foreign matter.

18 Removing, Repairing and Refixing existing Alluminium 4.00 Nos 929.20

window frame with glass of all size shutter/frame,

replacing all old fixtures with new locks, screws etc.

including repairing the shutter/frame with Rates includes

all labour charges for removing, repairing & refixing the

window, all materials, transport cost, taxes etc.and as

directed by engineer in charge etc complete.

Item Description of Item Quantity Unit Rate In Amount

19 Providing and laying 2 mm thick anti static Poly vinyl 71.06 Sqmt 2121.00

flooring of laid over 25 mm thick leveling layer of cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 10 mm nominal size) to be paid separately,

coated with a thin layer of hot bitumen penetration

80/25 (blown type) @ 2.45 kg per sqm, including fixing

blocks in position after dipping in hot bitumen (blown

type) up to half depth, planed, levelled smooth and

finished complete.

20 Providing and fixing Expansion joint following items (a) 16.88 Sqmt 13891.24

expansion joint 100 mm thick expansion joint board of

best quality and approved make including cutting to

required size and shape at all levels . (b) the expansion

joint by 600 polymer or equivalent confirm to BS 4254-

1983 as per required shade and manufactured

specification by making groove of 50 mm x 12.5 mm

lather by cutting or by repairing groove and removing

mortar drop or any other foreign materials including

applying primer and filling required size (oversize of joint

PU foam). (C) Applying and providing Expansion joint

sealing System on 100 mm vide joint including cleaning of

exansion joint by mechanical means provision of adhesive

and flexible membrane with required bond length as per

menufracturer specification and 4mm thick alluminium

strip covering with one side sloted and bolted with

suitable system, inclusive of all manpower, machinery

and material as per specification and as directed.

(d)fixing 25 cm Wide & 3mm thick exterior composite

panel on existing expansion joint horizontally & vertically

with all material, hardware, acessories & fittings etc

completed.all items above a to b carry out as per directed

engineer incharge

21 Replacing old & u/s wiring by Point wiring for Light / Bell 13.00 Pt. 582.77

with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length , in below

type of pipe erected with 6A Modular type switch / bell

push & accessories and earth continuity of following

type, erected on PVC / Metallic/Wooden box, single

mounting base frame covered with

textured/metallic/white front plate modules erected on /

in wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed. (f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

Item Description of Item Quantity Unit Rate In Amount

22 Replacing old & u/s wiring by Point wiring for Tissino / 7.00 Pt. 200.99

Modular secondary light point with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (green) both are of ISI marked 1.1 kV

grade FRLS PVC insulated multi strand copper wires, in

below type of pipe to be erected complete with earth

continuity and necessary connection with primary light

with accessories erected on Metal / PVC / wooden box

covered with 3 mm thick PC(Polycarbonate) / Acrylic

sheet for open / concealed wiring. with necessary Lamp

holder / ceiling rose / H.D.Connector as directed. (f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

23 Replacing old & u/s wiring by Point wiring for FAN with 2- 10.00 Pt. 809.01

1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of

.ISI marked 1.1 KV Grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of

pipe erected with 6A Modular type switch and hum free

EME step type electronic fan regulator mounted and

accessories with earth continuity of following type

erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured/metallic/white front

plate modules erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose / H.D.Connector as

directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete

24 Replacing old & u/s wiring by Point wiring for on board 6.00 Pt. 309.06

Looped Plug with 6A Modular type switch & 5 pin socket

erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

plate modules erected on / in wall / ceiling with

following type accessories Cat. III

25 Replacing old & u/s accessories by Providing following 3.00 Ea. 151.50

type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (1)One No. SP

26 Replacing old & u/s accessories by Providing following 3.00 Ea. 151.50

type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (2) One No 5 pin

Item Description of Item Quantity Unit Rate In Amount

27 Replacing old & u/s accessories by Providing following 1.00 Ea. 160.59

type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (3) Two Pin/RJ-

11 Telephone Socket [A] For One Gang Cat.III

28 Replacing old & u/s accessories by Providing following 7.00 Ea. 25.25

type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (7) Blank Plate

29 Replacing old & u/s accessories by Providing following 17.00 Ea. 160.59

type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (8) Computer

RJ-45 socket Cat.III

30 Replacing old & u/s accessories by Providing following 2.00 Ea. 180.79

type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (9) 16 Amp. SP

one way switch Cat.III

31 Replacing old & u/s accessories by Providing following 3.00 Ea. 199.98

type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (10) 6/16Amp.

Universal socket Cat.III

32 Replacing old & u/s accessories by Providing following 1.00 Ea. 410.06

type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (14) 6A/ 10A/

16A/ 20A/ 25A/ 32A Double Pole Modular MCB Switch

33 Replacing old & u/s mains by Providing and erecting 314.00 Mtr. 104.03

Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe

to be erected concealed in /flushed on wall/ceiling, with

1.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of

following size (A) With medium class Rigid PVC pipe and

accessories (b) 2 wire 2.5 sq. mm

Item Description of Item Quantity Unit Rate In Amount

34 Replacing old & u/s mains by Providing and erecting 20.00 Mtr. 140.39

Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe

to be erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) with

medium class Rigid PVC pipe and accessories (a) 2 wire

35 Replacing old & u/s mains by Providing and erecting 38.00 Mtr. 326.23

Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe

to be erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) with

medium class Rigid PVC pipe and accessories (h) 4 wire

36 Supplying and erecting Flexible PVC insulated multi 25.00 Mtr. 21.21

strand multi core 1.1 kV grade ISI marked copper wires of

following size to be erected as directed. (b) 1.00 Sq.mm

37 Supplying & erecting approved make LAN cable of 285.00 Ea. 47.47

following size in existing pipe as per direction [C] CAT -

38 Replacing old & u/s computer baord by Providing & 17.00 Ea. 1133.22

erecting Switch board for Computer or electric apparatus

consisting of following modular type accessories

mounted with PVC / Metallic concealed/open box with

single mounting base frame covered with

textured/metallic /white front plate,modules erected

with necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat.

39 Decorative call bell Ting-tong box type 250 volts complete 1.00 Ea. 71.71

Item Description of Item Quantity Unit Rate In Amount

40 Replacing old & u/s tubelight by Supplying and erecting 5.00 Ea. 535.30

LED indoor fittings with LEDs of wattage 0.2 Watt to

Watt assembled on single MCPCB, with housing used as a

heat sink shall be made of thick sheet Steel conforming to

IS: 513/CRCA/ aluminium die cast powder coated and

high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor more

than 0.95, THD < 15%,CCT 3000 K to 6500K, Luminaire

efficacy> 85 lumens/watt ,LED LED driver efficiency >

% ( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.) (A)

Tube Light with integral driver (v) 36-40 Watts, Surge-2

KV, IP-20, conventional 4 feet Cat-lll

41 Replacing old & u/s TL by Supplying and erecting LED 14.00 Ea. 1794.77

indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated

and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company

mark/name 160V to 270V,Power Factor more than 0.95,

THD < 15 %, CCT 3000 K to 6500K, Luminaire efficacy>

LED driver efficiency > 85 % ( fitting required LM-79 &

LM-80 Certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the

ranges shown.) (B) LED Panel Light with provision for

Plane front frame with translucent cover fixed to housing

complete.IP20 (vi) 36 watts, 24" x 24", Surge- 2kV Cat-lll

42 Providing and erecting Miniature circuit breaker single 12.00 Ea. 123.22

pole 6A to 25A suitable to operate on 240 V A.C. system

and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark

43 Providing & erecting 415V MCB Four Pole Switch for 2.00 Ea. 702.96

Lighting Load (B curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following

capacity (b)40 Amp. Cat.III

Item Description of Item Quantity Unit Rate In Amount

44 Providing and erecting Sheet Steel powder coated MCB 1.00 Ea. 2339.16

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for (B) three

phase incoming and single phase horizontal type

outgoing Per phase isolation type (PPI) (b) sheet steel

double door (i)4 way

45 Replacing old & u/s fan by Providing and erecting 10.00 Ea. 1596.81

Approved make Ceiling fan with double ball bearing ISI

mark with condenser A.C. 230V.50 Hz.1200 mm. sweep

complete, canopy erected on existing hook or clamp with

earthing. [Make shall be approved by Engineer in charge]

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures

and words) of the estimated rate mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

The Contractor shall exhibit a board with detailed specification and details of work as directed by the

1 Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items

4 where there is a change as per actual mix design the cost of difference of cement consumption have been

deducted from the rate of original item at the rate of input rate mentioned in all the tender.

Deputy Executive Engineer Executive Engineer

Navsari ( R & B ) Sub Division Navsari ( R & B ) Division

Navsari Navsari