CONSTRUCTION OF CHEMICAL STORAGE BUILDING, WATER SUMP AND RENOVATION OF QC LAB, GENTS RESTROOM AT KOLLAM DAIRY

Amount

Dismantling Brick wall, Structural roofing along with all at required level by manually/ by mechanically means, carefully without damaging adjacent structres including stacking of servicable materials and disposal of unservicable materials within 50m lead from site all as per specifications and directed by EIC.

Dismantling Terracotta Tiles at 4M level by manually/ by mechanically means, carefully without damaging adjacent structres including stacking of servicable materials and disposal of unservicable materials within 50m lead from site all as per specifications and directed by EIC.

Earth excavation for Foundation trenches and seivage water sump as directed in all kinds of soil including dressing of sides, compaction of base, disposing the surplus excavated materials within a distance of 50m lead from site and lift 1.50m complete as per specifications. (Disposed soil to be levelled by breaking clods if any and neatly dressed).

Providing and laying PCC(1:3:6) in foundation and plinth using 20mm nominal size graded hard granite stone aggregate including compaction, finishing top surface to level, inclusive of shuttering rate etc; complete all as per specifications.

Earth filling with earth brought from outside upto plinth and in flooring, watering, consolidating and levelling to the required depth as per direction including conveyance, cost of materials, loading and loading etc. complete.

Providing and constructing Cement Block Masonry in CM 1:8 using solid block size of 40cm x 20cm x 20cm and approved quality for outer wall at all levels including cost of materials, conveyance, charges for labours, hire charges for scaffolding etc. complete and as per directed by EIC.

Providing and laying in position RCC (1:1.5:3) thick for flooring, beams, slabs using 20mm nominal size aggregate obtained from approved quarry including mechanical mixing, form/shuttering work in correct level, vibrating, compaction, finishing, curing, etc in slope if needed as per site condition; complete all as per specifications.

Plastering for walls, beams, ceiling etc in CM 1:5 with 9mm thick using M-sand of approved quality including cost of materials, conveyance, charges for labours, hire charges for scaffolding etc. complete as per directed by EIC

Painting with plastic Emulsion paint of approved colour and quality two coats over two coats of wall putty applied over a priming coat of cement paint for Inside & Outside walls including cost and conveyance of all materials to site, labour charges, hire charges for scaffolding , etc. complete.

Providing & fixing the Aluminium Mesh at required height using 1 x 1½ vertical & horizontal section including cost of materials, labour charges etc. complete all as per technical specifications and direction by Engineer In Charge.

Providing Floor finish with vetrified floor tiles of Kjareria, RAK, Somany OR equivalent with approved quality and size and thickness 8 mm or nearest laying in cement mortar 1:6, 12mm thick with a neat cement flushing coat etc. and closing the joints with epoxy joint filler to correct lines and levels including cost and conveyance of all materials to site, labour charges, charges for cutting and finishing to the required level/slope etc including cleaning the surface with acid etc. complete for all floors.

Providing Floor finish with Antiskid granite tiles of approved quality and size and thickness 30 mm laying in cement mortar 1:6, 12mm thick with a neat cement flushing coat etc. and closing the joints with epoxy joint filler to correct lines and levels including cost and conveyance of all materials to site, labour charges, charges for cutting and finishing to the required level/slope etc including cleaning the surface with acid etc. complete for all floors. (Note: Granite stone tiles will be supplied by TRCMPU Ltd)

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete as per specification and as directed by EIC.

Full Height partition: Providing and fixing in position partly glazed full Partition at 3M ht, in frame work 2mm thick at 2’x2’ grid (horizontally and vertically) comprising of 2½”x1 ½” vertically, 4"x1½" bottom member, glazed aluminum medium section with 4.5mm thick ACP sheets(1200mm high, both sides) of required shade, texture and pattern and partly glazed with 6mm thick plain glass with frost film as per direction (Saint Gobain make, from 1200mm upto required height, as per directions at site) fabricated out of extruded sections confirming to BIS IS 733 including supplying and fixing handles, locking arrangement fixtures and fastenings of aluminum etc. complete as per site condition

Half Height partition: Providing and fixing in Partition work at 1.20M ht in frame work 2mm thick at 2’x2’ grid (horizontally and vertically) comprising of 2½”x1 ½” vertically, 4"x1½" bottom member, glazed aluminum medium section with 4.5mm thick ACP sheets(1200mm high, both sides) of required shade, texture and pattern fabricated out of extruded sections confirming to BIS IS 733 including supplying and fixing handles, locking arrangement fixtures and fastenings of aluminum etc. complete as per site condition

Steel reinforcement using TMT bars for all R.C.C items including decoiling, cutting, hooking, bending, cranking, fabricating to required shape, placing in position and tying the system with soft drawn annealed binding wire of diameter not less than 1.00mm with 2 strands etc complete

Providing and fixing Structural Steel sections of channel,angles,square and circular tubes etc welded/bolted, including cutting, hoisting, fixing in position and two coat synthetic enamal painting over a base coat of primer etc complete as per direction/ technical specification.

Supplying and fixing anodised Aluminium Door (1000mm*2100mm) partly panelled with 4.5mm thick ACP sheets(upto 1200mm height, both sides) and partly glazed(above 1200mm upto 2100mm height) single leaf doors, outer frame made out of 100mm x 45mm with threshold plates and shutter section out of 50mm x 45mm with sill section of 100mm x 45mm (wall thickness 2mm for all sections), door stopper, hinges of required number and size and all necessary accessories etc complete.

Supplying and fixing anodised Aluminium Sliding Window (1000*1500) fully glazed, outer frame made out of 100mm x 45mm with threshold plates and shutter section out of 50mm x 45mm (wall thickness 2mm for all sections), hinges of required number and size and all necessary accessories etc complete.

Providing and fixing GI Handrail at required level with 50mmX50mm squaretube including cutting, hoisting, fixing in position and two coat of synthetic enamel painting over a base a coat of primer et. Complete as per direction of EIC and Technical specification.

Providing and fixing PVC pipes of approved quality using 3/4 or 1 inch size with 6kg pressure including necessary fittings, bends, couplings, reducers etc. The rates shall includes cost of materials, labor charges, conveyance etc. complete as per specification and direction.

Providing and fixing Manhole Cover with using Cast Iron size of 45cm x 45cm on the top slab cover as per specification including frames and fittings, cost and conveyance of all materials and hire cahrges for labours etc. complete

Providing and fixing Hand wash sink of approved quality including necessary fittings cost of materials, labor charges, conveyance etc. complete as per specification and direction.

T G VARGHESE