REPAIR AND REPLACEMENT OF DIESEL GENERATOR SETS AMF PANELS AND FIRE FIGHTING AND FIRE ALARAM SYSTEM UNDER GE I NAVY JAMNAGAR

Amount

M&L to attend 'B' check for DG set of capacity 63 kVA (Make:Greaves) at different locations to carry out maintenance/servicing as given below once during the contract period as ordered including testing on completion of the following all as directed:- (i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer,Contactors, Meters and others etc. (ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/ silencer, Repair if required. (vi) Check electrical connections of engine. The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging Repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning. (xii) Change of Air filter element with O ring. (xiii) Change of filter insert with O ring (xiv) Change of Lub oil filter. (xv) Change of Primary filter element. (xvi) Change of secondary filter element. (xvii) Change of greaves lub oil CI4- 10ltrs pack (xviii) Change of Radiator pre-mix greaves kOOL 10 ltrs, complete to the satisfaction of Engr -in-charge. (Note: Cost of New minor spares required for replacement to make the DG set fully functional is included in quoted rate.)

All same as per item No. 1 here-in-above, but DG set of capacity 100 kVA Make: Greaves

All same as per item No. 1 here-in-above, but change of greaves Lub oil CI4- 20Ltrs pack complete for DG set of capacity 160 kVA Make: Greaves

All same as per item No. 1 here-in-above, but change of greaves Lub oil CI4- 20Ltrs pack complete for DG set of capacity 250 kVA Make: Greaves

M&L and attend 'B' check for DG set of capacity 15 kVA (Make: Kirloskar) at different locations to carry out maintenance/servicing as given below twice during the contract period as & when ordered including testing on completion of the following all as directed (i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer, Contactors, Meters and others etc.(ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/ silencer, Repair if required. (vi) Check electrical connections of engine. The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging, Repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning (xii) Change of Spinon Lub oil filter (xiii) Change of air cleaner element (xiv) change of Belt- AVX 10 1500 (xv) Change of fuel filter element (xvi) Change of KOEL care premium genuine oil 7.5Ltrs Can, complete all as specified and directed by Engr-in-charge. (Note: Cost of New spares required for replacement is included and no seperate payment for minor spares if any reqd, will be made on this account to contractor.)

All same as per item No. 5 here-in-above, but change of V Belt cogged- AVX10 1265L blower pulley, Change of V Belt cogged-AVX10 1136 for alternator pulley and Change of KOEL care premium genuine oil 13Ltrs Can, complete for DG set of capacity 40 kVA Make: Kirloskar

M&L and attend 'C' check for DG set of capacity 100 kVA (Make: Greaves) at different locations to carry out maintenance/servicing as given below once during the contract period as & when ordered including testing on completion of the following all as directed: (i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer, Contactors, Meters and others etc. (ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/silencer, Repair if required. (vi) Check electrical connections of engine. The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging Repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning (xii) Change of Gskt set 4G11TA (w/o Hd gskt) (xiii) Change of cogged belt AX43-1143L (xiv) change of pipe turbo oil supply (xv) Change of pipe turbo drain (xvi) Change of set of hoses for 4G valve (xvii) Change of setting screw (xviii) Change of hex nut M8x1 DIN934 (xix) Change of gasket for PDC rocker cover (xx) Change of set of flex F/P (xxi) Change of push rod. (Note: Cost of New spares required for replacement is included and no seperate payment for minor spares if any reqd will be made on this account to contractor.)

M&L and attend 'C' check for DG set of capacity 15 kVA (Make: Kirloskar) at different locations to carry out maintenance/servicing as given below once during the contract period as & when ordered including testing on completion of the following all as directed: (i) Check and clean engine,alternator battery,instrument panel,AMF panel,Timer,Contactors,Meters and others etc. (ii) Tightening of all nuts& bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension ,replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/silencer,Repair if required. (vi) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts,change AVM pads if found damaged. (viii) Check exhaust pipe,flange and lagging Repair if found damaged. (ix) Check output of alternator ,if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling,Greasing and checking for proper & smooth functioning(xii) Change of rocker cover gasket (xiii) Change of valve seat insert inlet & exhaust (xiv) change of valve pair inlet & exhaust (xv) Change of set of joints (xvi) Change of set of O rings HA294 (xvii) Change of intermediate ring 1.1mm (xviii) Change of valve guide (xix) Change of valve stem seal , complete all as specified and directed by Engr -in-charge. (note :- Cost of New spares required for replacement is included and no seperate payment for minor spares if any reqd, will be made on this account to contractor. )

All same as per item No. 8 here-in-above, but for DG set of capacity 40 kVA Make: Kirloskar

Overhauling of DG set of capacity 63 kVA (Make:Greaves) by Dismantling from foundation & transporting of Engine and alternator to work shop for complete servicing & repair. Dismantling the engine complete by taking out radiator, pump assembly, casing top cover, head assembly, piston, filters, hose pipes, fuel pipe, fuel pump assembly, exhaust etc for complete repairing/ servicing of engine and repair/ repalacement of unserviceable/ wornout parts, complete oiling, greasing and servicing of all the parts of DG set and reassembling complete and testing engine for proper functioning, transportation of DG set to site and fixing, connecting, commissioning and testing on load complete all as directed Note: (i) Supply only of new items required for replacement will be measured and paid seperately under respective items of schedule. (ii) Rate quoted by contractor includes the cost of small parts such as O rings, washers, nuts, bolts, gasket etc and repair such as oil cooler servicing, connecting rod grinding etc. as directed by Engr-in- Charge.

All same as per item No. 10 here-in-above, but for DG set of capacity 100 kVA Make:Greaves Note for Item Sr Nos. 1 to 11: All checks such as 'B', 'C' and overhauling has to be carry out only from authorised rep/ service engr / service technician of manufacturer or dealer/ stockist. No another mechanic is allowed to work on it. Service Engr / service technician has to submit his service report on each & every call / attendance/ service due dates as per schedule laid down by manufacturer as directed by Engr-in-charge. No extra payment will be made on this account.

Supply only Valve inlet for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Valve exhaust for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Valve guide for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Valve seat inlet for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Valve seat Exhaust for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Valve stem seal for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Piston for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Piston ring for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Cylinder liner for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Thermostat for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Main Bearing for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only C R Bearing for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Thrust washer for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Con rod bush for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Piston cooling nozzle for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Oil seal for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Cam bush for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only oil pump for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only water pump for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only set of gasket for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only set of o ring for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only set of hoses with clipsfor DG set of capacity 63/ 100 kVA Make: Greaves

Supply only set of fuel pipes for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only set of injector pipes for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only set of Belt for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Exhaust silencer for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only injector with nozzle for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only water manifold for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Pre mix coolant 10 ltrs pack for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Oil 10 ltrs pack for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Lub oil filter for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only fuel filter primary for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only fuel filter secondary for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Air filter outer for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Air filter inner for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only LOP switch 2.5kg/sqcm for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only W T switch 95+/-2degcel for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only 12V temp guage (40-120 deg cel) for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only 12V press guage, 0-10 bar for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only LOP sensor cum sw=010bar for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Temp sensor=150deg cel for DG set of capacity 63/ 100 kVA Make: Greaves

Servicing and caliberation of FIP (Fuel injection pump) & nozzles including replacement of minor parts like nuts,bolts,washers etc of following :-DG Set 63/100 KVA capacity

M&L for taking out Radiator of DG set 63 kVA/100 kVA Make: Greaves for repair, welding, brazing, leak testing & refixing to DG set to its original position and testing complete all as directed.

Servicing & repair to self starter of DG set of capacity 15/40 kVA (Make: Kirloskar) including replacement of parts such as washer, nut, bolts, bush, solenoid, rotor etc. assembling and testing complete.

All same as per item No 55 here-in-above, but for DG set of capacity 63/100 kVA Make: Greaves

All same as per item No 55 here-in-above, but for DG set of capacity 160/250 kVA Make: Greaves

S&F in replacement Solonid Switch & Relay card for 15/40 kVA DG set Make:kirlosakar and testing complete for proper functioning.

S&F in replacement Solonid Switch & Relay card for 63/100 kVA DG set Make: Greaves and testing complete for proper functioning.

S&F in repair Solonid Switch for 160/250 kVA DG set Make: Greaves and testing complete for proper functioning.

S&F in repair AVR suitable for 15 kVA DG Set complete all as directed.

S&F in repair AVR suitable for 40 KVA DG Set complete all as directed.

S&F in repair AVR suitable for 63 KVA DG Set complete all as directed.

S&F in repair AVR suitable for 100 KVA DG Set complete all as directed.

S&F in repair AVR suitable for 160 KVA DG Set complete all as directed.

S&F in repair AVR suitable for 250 KVA DG Set complete all as directed.

S&F in repair battery auto cable copper PVC insulated unsheathed 35 Sqmm single core copper cable complete.

S&F in repair battery auto cable copper PVC insulated unsheathed 95 sqmm single core copper cable complete.

S&F 90AH 12Volt Lead acid battery (Maintenance free battery with min 2 years warranty) for DG set. Make: Exide Xpress

S&F 150AH 12Volt 12Volt Lead acid battery (Maintenance free battery with min 2 years warranty) for DG set. Make: Exide Gold

S&F battery lugs for DG set battery complete all as directed by Engr in charge.

S&F in repair Ignition Switch of DG Sets & complete all as directed.

S&F in repair No volt coil for contactor of capacity up to 200 Amp Capacity all as specified and as directed by EIC. Make : L&T /C&S/Schneider

S&F in repair LED type pilot lamp. Make: C&S / L&T

S&F in repair Volt meter 0-500 Volt in existing panel including wiring from bus bar to volt meter terminals iand fix the wiring wit existing control wiring all as directed. Make: L&T/ Meco/ HPL

S&F in repair Ammeter 0-100 Amp in existing panel with necessary wiring from CT to Ammeter and fix the wiring in existing set of control wiring all as directed. Make: L&T/ Meco/ HPL

S&F in repair Ammeter 0-200 Amp in existing panel with necessary wiring from CT to Ammeter and fix the wiring in existing set of control wiring all as directed. Make: L&T/ Meco/ HPL

S&F in repair electronic timer of 215/240/360/415 Volt 3 to 120 Sec all as directed. Make: L&T/C&S/Schneider

M&L for wiring loom of control panel of DG Set AMF panel from Relay and auxilliary contacts complete by using 2.5 sq.mm copper cable of colour code from auxilliary contacts to Realy including fault finding etc all as specified and as directed.

M&L for Overhauling of water pump with repairing kit for 15/40 kVA DG set complete all as directed.

M&L for Overhauling of water pump with repairing kit for 63/100 kVA DG set complete all as directed.

M&L for Overhauling of water pump with repairing kit for 160/250 kVA DG set complete all as directed.

M&L for complete checking of AMF panel,finding the fault, servicing complete including replacement of unserviceable spares and testing complete for manual & Auto operations all as directed. Note: Supply only of new items required for replacement will be measured & paid seperately under respective item of schedule.

Supply only AMF Relay.

Supply only single phase preventor.

Supply only PLA relay.

Supply only 3 pole power Contractor ML-4, 70 A, 415 V. Make: L&T/Legrand

S&F in repair HRC Fuse base of capacity 200 Amps.

Supply only 3 pole power Contractor ML-4, 163 A, 415 V. Make: L&T/Legrand

S & F Anti vibration pad set suitable for 63/ 100kVA DG set all as directed.

M&L for taking out alternator of DG set of capacity 15 kVA (Make: Kirloskar) by dismantling from engine pulley including disconnecting electrical connection complete & transporting to workshop. Opening the rotor and stator for rewinding with copper wire of existing guage and then revarnishing the stator & rotor with good quality varnish, Heating and baking complete upto requisite duration. Check bearing & shaft for machining if reqd. Re-assemble stator & rotor by replacing existing bearings with new bearings complete. Retransportation alternator to base and coupled with engine by using new rubber bushing spider, nutbolts complete. Testing the system for smooth functioning & checking current and load output by giving existing electrical load and to the entire satisfaction of engr in charge.

All same as per item No. 92 here-in-above, but for DG set of capacity 40 kVA Make: Kirloskar

All same as per item No. 92 here-in-above, but for DG set of capacity 63 kVA Make: Greaves

All same as per item No. 92 here-in-above, but for DG set of capacity 100 kVA Make: Greaves

M&L for Readymade electrolyte having specific gravity 1.4 for DG set of any capacity all as directed.

M&L for Distilled water having specific gravity 1.0 for DG set of any capacity all as directed.

S&F in repair MCCB thermal magnetic protection unit rating 160 Amp, 4 pole, 25 kA type DPX3 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and ncluding necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items complete all as specified.Make:Legrand Cat No. 4200 57 or equivalent in ABB / Siemens/ L&T

S&F in repair MCCB thermal magnetic protection unit rating 100 Amp, 4 pole, 25 kA type DPX3 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and ncluding necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items complete all as specified. Make:Legrand Cat No. 4200 55 or equivalent in ABB / Siemens/L&T

Supply installation, commissioning and testing of Analogue Addressable Fire Alarm Control Panel including detector wise configuration facility 2000 Event Storage with Real Time Clock, Upto 192 grouping facility, Pre Alarm Action, Programmable detector sensitivity. Device type verification, Earth fault annunciation facility at 0 ohms, Double Address Sensing, Loop wise device test. 40 X 4 Characters LCD display 2 numbers of loop card and 200 devices in any combination per loop. Day / Night Mode facility. USB 2.0 Interface for PC connectivity. Rs. 485.00 Communication facility for Network / Repeater / MODBUS / BACnet. Programmable Auto Silence Facility. Programmable AC Loos Delay. Programmable Silence Inhibit. Two No’s of programmable inputs. Battery low audio, visual warning. Three programmable Form C relay for Fire, Fault and Supervisory. Primary Power 120 / 220VAC + 10% -15%, 60 / 50 Hz. Standby Power 24V D.C (2 No’s of 12V, 40 Ah (Max), Built in for 12Ah) Sealed Lead acid battery Operating Condition Operating Temperature 0 - 49° C / 32-120° F. Relative Humidity 93 ± 2% RH (non-condensing) at 32 ±2° C / 90 ±3° F including taking down old unserviceable Panel complete all as specified and as directed.

Supply commissioning and testing of Smoke detector Operating Voltage Range: 9 to 32 VDC Volts Non-polarized Standby Current: ≤100µA @ 24 VDC, Maximum Alarm Current (LED on ): ≤55mA @ 24 VDC, Operating Humidity Range: 10% to 93% Relative Humidity, Non-condensing, Operating Temperature Range: 14°F to 120°F (-10°C to 49°C), Adjustable Sensitivity: 1-2.5%/FT, Height: 2.2 (55 mm) installed in Base including taking down old unserviceable smoke detector complete all as specified and as directed.

S&F in repair of Batteries DC, 12V, 7 AH, lead acid duly initial charged complete all as specified and as directed. Make: Exide / Star Gold

Supply, commissioning and testing of Fire Alarm Hooter made out of iron, red colour operating voltage 24 DC supply Dimensions (L x B x H): 18.5cm x 13 cm x 7.5 cm including taking down existing fire alarm hooter complete all as specified and directed.

Supply, commissioning and testing of Addressable manual call point resettable type including taking down existing addressable maual call point complete all as specified and as directed.

S&F in repair of Hydrant valve single headed Gun metal landing valve (internal/external Fire-Hydrants) with oblique type single outlet complete with hose coupling adaptor of 63 mm size, instantaneous spring lock arrangement and blank cap with chain conforming to IS 5290 complete all as directed

S&F in repair of Flanged stand post CI of 80 mm dia 1.5 m height complete all as directed

M/s Balaji Enterprise

suvidhiconstruction

M/S Badri Electicals

Prime Decor

Nitesh Enterprise

Ravi enterprise