SRMO Ind. Road and road side drain (Metalling and tarring) at Industrial Area, Bhambla Distt. Mandi (HP).

Amount

Providing and laying spreading and compacting stone aggregate of specific sizes of water bound Macadam specification i/c spreading in uniform thickness hand packing rolling with three wheel 80-100 kN static roller in stages to proper grade and camber applying and brooming crushable Screening to fill-up the interstices of coarse aggregate watering and compacting to the required Density Grading -1 as per Technical Specification

Providing and applying primer coat with bitumen emulsion (SS-I) on prepared surface of granular Base i/c cleaning of road surface and spraying primer at the rate of 0.70-1.0 Kg/ sqm using Mechanical means as per Technical Specification .

P/L bituminous macadam with hot mix plant using crushed agg. Of grading as per Table 500.4 premixed with bituminous binder transport to site up to a load of 1000m laid over a preously prepared surface with paver finished to the required grade level and achieve the desired compaction as per Tachnical Specification

Providing and applying tack coat with bitumen emulsion (RS-I) using emulsion pressure distributor At the rate of 0.30 to 0.35 kg per sqm on the prepared non-bituminous surfaces ( cement concrete Pavement) cleaned with Hydraulic broom as per Technical Specification.

Providing, laying and rolling of open graded premix carpet of 20mmcompacted thickness, composed of Type-B 13.2mm to 5.6mm aggregate at rate of 0.27 cum , mixed with Bitumen MS Cold at the rate 2.15 Kg per square metres of road surface to required line grade and level to serve as wearing course on a previously prepared base, including mixing and heating binder and aggregate in cold mix Plant 30/40Tonne per hour capcity, transporting mixed material with tipper and laying manualy to the required grade and camber and rolling with a three Wheel 80-100 kN static road roller, finished to required level and grades to be followed by a seal coat as per M.O.R.D. technical specifications clause 508

Providing and laying seal coat sealing the voides in a bituminous surface laid to the specified levele and Cross fall using type A type-B type-C as per technical specification clause 510 by manual means & 6.80kg 10m2 type-A -S-90.

Excavation in dumped stone or mulba i/c stacking of serviceable and un-serviceable material seprately and disposal of un-seviceable materail lead upto 20mtr. Disposed material to be neatly dressed

Cleaning jungle i/c uprooting of rank vegetation grass brush wood trees and sapling girth to 30cm measured at height of 1.00 mtr

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. Centre Line, Side Line, Zebra Crossing

Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide strips, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming toIRC-79 and the drawings.

Providing & erecting direction and place identification retro-reflectorised sign as per IRC-67 made of lens type reflective sheeting vide clause 1701.23, fixed over aluminium sheeting, 2mm vide area not exceeding 0.9 sqm. Supported on 2 inch dia GI pipe frimly fixed to the ground by mean of properly designed foundation with M-15 grade concrete 450x450x600mm below G.L as per approved drawings & technical specification clause-1701.

Painting two coat i/c prime coat with epoxy paint of approved brand on concrete/ steel surface after through cleaning of surface to give an even shade as per drawing & technical specification clause-1701.

Providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873 (Part 4) 1973 including carriage of material within all leads and lifts.

Providing and fixing 0.5HP round out door water fountain & waterfall arrangement as per drawing with all plumbing and electrical work, Lighting, pump for circulation of water as per the directions and model approved by the Engineer In charge. (i/c all Civil works )

Providing and fixing C.I. (Cast iron benches of approved design and specifications). Stand/legs made up of decorative cast iron material for mounting, 15inches in width and weighing approximately 85kg complete including the cost towards loading/ unloading transportation fixing if applicable at site complete all as per drawing and technical specifications and as directed by Engineer-in-charge.

Excavation in earth work and disposal of all excavated earth upto all lead and lift (disposed earth to be levelled and neatly dressed.

Providing from work with steel plates 3.15mm thick weled with angle iron in frame 30x30x5mm so as to give a fair finish including levelling centering, shuttering strutting and propping etc. With wooden battens and ballies, hight of propping and cenring below supporting floor two ceiling and removal of the same for instu- reinforced concrete and plain concrete work in:- (a) vertical surface sch as wall any thickness partition plaster and string course and like .

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge

Providing and laying cement concrete work 1:3:6 (1cement: 3sand: 6graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work

Providing and laying cement concrete 1:4:8 (1cement:4sand:8graded stone agregate 40mm nominal size) and curring complete excluding cost of form work in foundation and plinth.

Providing and laying heavy duty precast cement concrete inter locking paver blocks vibro compacted upto M- 30 grade i/c border or kurb block gray or coloured over sub-base of concrete with 25mm thick average thickness ofsand bed laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curring rubbing & polishing complete (sub base concrete floor to be paid for separately) 80mm thick inter locking blocks. as per IS specification 1506

Steel work welded in built up sections, trusses and framed work, i/c cutting, hosting, fixing in position and appling a priming coat of red lead paint:- (a) In Gratings and ledder ,railing & similar work

Demolition above G.L. up to floor two level including stacking of serviceable materials and disposal of un-serviceable meterials with in 20mtrs lead. In cement mortar. un-reinforced cement concrete upto 15cm thickness.

15mm cement plaster in singale coat on the fair side of brick/concrete/stone walls for interior plastring upto floor two level including arrrises, internal rounded angles, chamfers and/or rounded angle not exceeding 80mm in girth and finished evehn and smooth in cement mortar 1:6(1cement :6sand).

Filling in Plinth with sand under floor including watering ,ramming, consolidating & dressing complete.

Providing & laying cement concrete flooring 1:2:4(1cement: 2sand: 4graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement.40mm thick

Gaurav Singh