DEVELOPMENT OF RURAL CIRCUIT MALANAD MALABAR CRUISE TOURISM PROJECT PHASE 11 MUTHAPPAN and MALABARI CUISINE CRUISE -KOLACHERY ISLAND-under Swadesh Darshan Scheme

Amount

Providing Bioshield near the banks with length of 300m

od80395/2019_2020 : Planting bamboo at 1 feet interval from existing Kaitha layer towards Land and tying together using bamboo rails of 4 inch diameter in size. The size of plant should be 2-4 feet (including all conveyance)

od80399/2019_2020 : Cultivation of Kaitha( screw pine) on the banks of shore and binding with 4inch bamboo rails. The size of plant should be 2-4 feet heigh. (including all conveyance)

od80404/2019_2020 : Cultivation of Mangrove saplings 6 feet (Rhizhophora mucronata) in mud filled Bamboo posts of size five inch diameter at a depth of two feet with an interval of one feet. Bind theese bamboo posts using 4 inch diameter bamboo rails. (including all conveyance)

Construction of Chinese net and rest room

60.64.1 : Coconut Pile - Supplying and stacking well matured straight coconut post for driving down throug various strata bellow bed level including cost coveyance labour charges etc complete. (Coconut tree available at island and conveyance will be paid if brought from outside).

60.64.4 : Coconut Pile - Driving down coconut pile to lines and levels through variuos strata including all hire charges and labour for fixing , staging platform and all other appliances necessary for pile driving down after pointing the bottom end.

60.64.6 : Cutting and removing the excess length of wooden piles to lines and levels and removing the cut end of piles and stacking within 150m

od80406/2019_2020 : Providing & fixing in position 6mm thick Bamboo ply wall cladding at all height with planks, as per specification and direction of engineer in charge (including all conveyance)

od80410/2019_2020 : Thatching roof with double new coconut cadjans over the roofing sheet with suitable arrangements as directed by the Architect The rate includes all cost of materials, labour charges, conveyance etc., complete in all leads and lifts for all floors complete. (including all conveyance)

50.9.13.1 : Supplying and fixing Anjily wood wrought and put up for roof members including cost and conveyance of materials etc. complete .

50.9.14.1 : Supplying and fixing Anjily wood reapers of size 50x25 mm with wire nails including cost and conveyance of materials etc. complete.

od80420/2019_2020 : Chinese net of specified nylon/required quality and quantity of mesh size 15mm to 100mm of width 20 to 30ft etc.complete (including all conveyance).

Construction of Rain water pits

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

26.18.3 : Supplying and laying high strength flexible geogrids (HSFG) as soil reinforcement / basal reinforcement as per MORTH 3100 and IRC 113, made of high tenacity polyester core with polyethylene coating with Minimum Long Term Design Strength (LTDS) of more than 50% of ultimate tensile strength at 30 degree Celcius corresponding to 12 % strain .Ultimate tensile strength- 200 kN/m. (Prior sample approval required).

Construction of Biotoilet and Septic tank

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.(If only, earth is not available at site.)

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size). Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size. Assessment of strength of concrete by cube test in Govt. lab.

5.2.2 : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size). Assessment of strength of concrete by cube test in Govt. lab.

5.3 : Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15⁰ landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preferences

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.6.7.1 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.

od83393/2019_2020 : Exposed Laterite masonry in CM 1:6 (1 cement : 6 course sand) for superstructure with neatly dressed best quality laterite stones of approved size and quality. The rate includes pointing the joints with matching colour pigment with least thickness. The cost includes all cost of materials, labour charges, conveyance, curing etc. complete as per standard specification. (Observed ) (including all conveyance)

13.2.1 : 15 mm cement plaster on the rough side of single or half brick wall of mix:1:4 (1 cement :4 fine sand)

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

21.17 : Providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.(Only weight of grill to be measured for payment ).Make:INDAL,JINDAL or Eq.

9.121 : Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. Make: Sintex or eq. make with IS.

9.122.1 : Providing and fixing to existing door frames.30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS : 14856, including fixing to frames. Make: Sintex or eq. make with IS.

11.40 : Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of Ist quality conforming to IS: 15622 of approved make in all colours, shades, except white, Ivory, Grey Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete. Make: Khajaria, Johnson, RAK, NITCO, Cera or eq. in the order of pref and sample approval from KEL/client.

11.36 : Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Make: Khajaria, Johnson, RAK, NITCO, Cera or eq. in the order of pref and sample approval from KEL/client.(Additional 12 mm thick plastering required).

50.9.13.1 : Supplying and fixing Anjily wood wrought and put up for roof members including cost and conveyance of materials etc. complete .

50.9.14.1 : Supplying and fixing Anjily wood reapers of size 50x25 mm with wire nails including cost and conveyance of materials etc. complete.

od80410/2019_2020 : Thatching roof with double new coconut cadjans over the roofing sheet with suitable arrangements as directed by the Architect The rate includes all cost of materials, labour charges, conveyance etc., complete in all leads and lifts for all floors complete. (including all conveyance)

od80430/2019_2020 : Trellising thatched roof with 1/6th split new bamboo reepers 60 cm apart diagonally. (including all conveyance)

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer. Make: Asian, Berger, Nerolac or eq. in the order of pref.

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work. Make: Asian, Berger, Nerolac or eq. in the order of pref.

od80432/2019_2020 : Prepare the surfaces of exposed laterite/brick / RR wall and applying two or more polyurethane based coating of MRF tile garde or approved spray polish over a priming coat with approved shade as recommended by the manufacturer after rubbing, cleaning. The rate includes all cost of materials, labour, scaffolding etc. for all leads and lift at all levels. (including all conveyance)

8.10.2 : Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in Charge and finished smooth.Granite Stone of approved shade

17.2.1 : Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

17.7.4 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x400mm with single 15 mm C.P.brasspillar taps

17.31 : Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

17.60.1.1 : Providing and fixing trap of self cleansing design with screwed down or hinged grating without vent arm complete, including cost of cutting and making good the walls and floors:100 mm inlet and 100 mm outletSand cast iron S & S as per IS : 3989

17.70.1 : Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the center of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

17.80 : Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx.size 610x390x370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer - in-charge.

50.17.1.3 : Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

50.18.8.4.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 10Kgf/cm2

50.18.9.7.1 : Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 6Kgf/cm2

50.18.9.16.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10Kgf/cm2 - External work - Exposed on wall

50.18.9.19.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

18.17.3 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40 mm nominal bore

18.21.2.1 : Providing and fixing uplasticised PVC connection pipe with brass unions:45 cm length15 mm nominal bore

18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

18.48A : Providing and fixing rectangular high density polyethylene water storageloft tank with cover, conforming to ISI : 12701, colour of opaque white or asapproved by Engineer-in-charge. The rate includes making necessary holesfor inlet, outlet & over flow pipes. The base support i/c fittings & fixtures fortank shall be paid separately.Make : Sintex white 3 layer with IS.

19.4.1.1 : Providing and fixing square-mouth S.W. gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

50.18.9.18.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall

od80433/2019_2020 : Providing and fixing bend of required degree with access door, insrtion rubber washer 3 mm thick, bolts and nuts complete. ) :-110 mm dia. PVC 6Kgf/cm2 (including all conveyance)

od80434/2019_2020 : Providing and fixing bend of required degree with access door, insrtion rubber washer 3 mm thick, bolts and nuts complete. :-75 mm dia. PVC 6Kgf/cm2 (including all conveyance)

od80435/2019_2020 : Providing and fixing T or Y of required degree with access door, insrtion rubber washer 3 mm thick, bolts and nuts complete : :-110 mm dia. PVC 6Kgf/cm2 (including all conveyance)

od80436/2019_2020 : Providing and fixing T or Y of required degree with access door insrtion rubber washer 3 mm thick bolts and nuts complete 75 mm dia PVC 6 Kg f/cm2 (including all conveyance)

od80437/2019_2020 : Providing and fixing Vent coul : :-110 mm dia. PVC 6Kgf/cm2 (including all conveyance).

od80438/2019_2020 : Providing and fixing Vent coul : :-75 mm dia. PVC 6Kgf/cm2 (including all conveyance)

od80439/2019_2020 : Providing and fixing plain bend of required degree. (without door), :-110 mm dia. PVC 6Kgf/cm2 (including all conveyance)

od80440/2019_2020 : Providing and fixing plain bend of required degree. (without door) :-75 mm dia. PVC 6Kgf/cm2 (including all conveyance)

19.7.1.1 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

19.32.1 : Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

od83480/2019_2020 : Supplying and fixing C.I. cover with frame for manholes : 610x610 mm rectangular C.I. cover (medium duty) the weight of the cover & frame to be not less than 58 kg. (including all conveyance)

51.19.ST4 : Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately)4. 35 to 50 flush capacity. Make: Sintex,United,Ocean or eq. in the order of pref.

Note: Make of water supply and sanitary items: Best branded ISI make Jaquar, Cera, Hindware, Parryware or eq. in the order of pref. Water pipe: Supreme, Finolex or eq. with IS and all fittings with IS.

Construction of Reverse Osmosis plant with well

od80392/2019_2020 : IRON REMOVAL FILTER -1865 Model (Pentair -Make/Equivalent make) 4000 LPH Maximum capacity,size of Filter Chamber 473 mm Dia.x 1645 mm Ht. with 40 NB Multiport Valve, 10.0 Bar Maximum Operating Pressure, and 2.0 Bar Minimum infeed Pressure (including all conveyance)

od80397/2019_2020 : Automatic Sensor as per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

od80401/2019_2020 : Automatic CHEMICAL DOSING PUMP - 5 LPH @ 4 kg/cm Capacity (Chemi dose -make/Equivalent make) as per approved design and specification , approval of KEL/Client and direction of Engineer at site (including all conveyance)

od80408/2019_2020 : FILTER FEED PUMP WITH STARTER KDS 1.522 Model (Kirloskar- make/Equivalent make) as per approved design and specification , approval of KEL/Client and direction of Engineer at site (including all conveyance)

od80411/2019_2020 : ACTIVATED CARBON FILTER - 1865Model (Pentair-Make/Equivalent make)4000 LPH Maximum Capacity,size of Filter Chamber 473 mm Dia.x 1645 mm Ht.with 40 NB Multiport Valve, 10.0 Bar Maximum Operating Pressure, and 2.0 Bar Minimum infeed Pressure as per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

od80414/2019_2020 : PRESSURE SAND FILTER - 1865 Model(Pentair - Make/Equivalent make) 4000 LPH Maximum Capacity,Size of Filter Chamber 473 mm Dia.x 1645 mm Ht with 40 NB Multiport Valve, 10.0 Bar Maximum Operating Pressure, and 2.0 Bar Minimum infeed Pressure. (including all conveyance)

od80416/2019_2020 : REVERSE OSMOSIS SYSTEM- 2000 lits/hr.Capacity, GE/Equivalent make 2 Nos.of Spiral wound TFC polyamide Membrane and UKL/Equivalent 2 Nos.of FRP-MOC of membrane housing(8" dia x 40" long) and 1 No of SS 304 Lubi/CRI/EqvntHigh pressure pump with 3 HP Motor, Imported PVC Interconnecting piping, 2 Nos.of Pressure Gauge, 2 Nos.of Flow meter, 1 No Digital TDS meter,Valve 1 No of Solenoid, 1 set (2 Nos.) Low & High pressure switch and 1 No Automatic Control Panel as per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

od63681/2019_2020 : Plumbing &Electrical Materials including fixing etc. complete as per the direction of Engineer at site. Including preperation of estimate based on PRICE/PWD schedule, preperation of drawing and getting approval from KEL/client and payment after deducting tender below:

Note: Make of water supply and sanitary items: Best branded ISI make Jaquar, Cera, Hindware, Parryware or eq. in the order of pref. Water pipe: Supreme, Finolex or eq. with IS and all fittings with IS.

Electrical items :As per approved list Enclosed.

Construction of Plastic waste Collection points

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge (If earth is not available at site).

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size). Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

11.40 : Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of Ist quality conforming to IS: 15622 of approved make in all colours, shades, except white, Ivory, Grey Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete. Make: Khajaria, Johnson, RAK, NITCO, Cera or eq. in the order of pref and sample approval from KEL/client.

9.1.2 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal wood

50.9.2.1 : Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge.using Anjili/ Jack wood

50.9.4.1 : Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood

9.97.2 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:250x10 mm. Make with IS.

od80423/2019_2020 : Providing & fixing in position 6mm thick Bamboo ply wall cladding at all height with planks, as per specification and direction of engineer in charge (including all conveyance)

50.9.13.1 : Supplying and fixing Anjily wood wrought and put up for roof members including cost and conveyance of materials etc. complete .

50.9.14.1 : Supplying and fixing Anjily wood reapers of size 50x25 mm with wire nails including cost and conveyance of materials etc. complete.

od80425/2019_2020 : Thatching roof with double new coconut cadjans and Trellising thatched roof with Arecanut 1/3 split reepers at 60cm apart both ways including laying straw over cadjans and covering with fibre net neatly with suitable arrangements as directed by the Architect The rate includes all cost of materials, labour charges, conveyance etc., complete in all leads and lifts for all floors complete. . (PWD Data witlh LMR) (including all conveyance)

Waste Bins

od80402/2019_2020 : Design,supplying and fixing one meter height bamboo cane waste bin of 50 cm diameter as per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

Construction of Projected Organic Balconies

60.64.1 : Coconut Pile - Supplying and stacking well matured straight coconut post for driving down throug various strata bellow bed level including cost coveyance labour charges etc complete. (Coconut tree available at island and conveyance will be paid if brought from outside).

60.64.4 : Coconut Pile - Driving down coconut pile to lines and levels through variuos strata including all hire charges and labour for fixing , staging platform and all other appliances necessary for pile driving down after pointing the bottom end

60.64.6 : Cutting and removing the excess length of wooden piles to lines and levels and removing the cut end of piles and stacking within 150m

50.9.13.1 : Supplying and fixing Anjily wood wrought and put up for roof members including cost and conveyance of materials etc. complete .

od80409/2019_2020 : Supplying and fixing Anjili wood plained planks of 25cm width screwed with 80mm size brass screws in suitable spacings, including cost and conveyence of materials etc. complete. (including all conveyance)

od80413/2019_2020 : Supplying fixing Bamboo balusters and railings for handrails using treated bamboo fixing in position etc complete including cost conveyence and all labour charges etc complete as per drawing and design, 50mm dia bamboos @10cm c/c, top railings etc. as directed by the architect as per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

od80417/2019_2020 : Supplying and fixing SS Nut & bolts for fixing planks bressummers etc including cost conveyance and all labour charges etc complete (including all conveyance)

od80421/2019_2020 : Polyurethane based Melamine spary polishing : -Two or more coats on new works including a coat of wood filler, melamine primer. Melamine sealer etc.(14.70.1 (derived)) (including all conveyance)

Providing Solar lamp

od80394/2019_2020 : Supply of Solar LED Lamp of 75W of havells or equivalent brand etc.completeas per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

od80398/2019_2020 : Supply of 100W Solar Panel of Havells or equivalent brand etc.complete as per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

od80403/2019_2020 : Battery - 60Ah Solar c10 as per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

od80405/2019_2020 : Pole with Battery Box - 4 METER LENGTH GI COATED as per approved design and specification , approval of KEL/Client and direction of Engineer at site as per approved design and specification , approval of KEL/Client and direction of Engineer at site (including all conveyance)

od80412/2019_2020 : Cables and charge controller (6 Meters of DC Cables ) as per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

od80415/2019_2020 : Installation &Supervision of Erection for one set of solar lamps with all accessories as per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

Construction of Play area

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size). Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

4.1.2 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size).

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.6.7.1 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.

2.27 : Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming consolidating and dressing complete.

2.28.1 : Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil

od81198/2019_2020 : Childrens Play Equipment 12 Feet Trampoline(Rate including shipping charges and conveyance to site).

od81199/2019_2020 : Childrens Play Equipment Adventure Net Rate including shipping charges

od81200/2019_2020 : Childrens Play Equipment Tyre maze (Rate including shipping charges and conveyance to site).

od81201/2019_2020 : Childrens Play Equipment Multi seater swing(Rate including shipping charges and conveyance to site).

od81202/2019_2020 : Childrens Play Equipment Slide including shipping charges (Rate including shipping charges and conveyance to site).

od81203/2019_2020 : Childrens Play Equipment Merry Go Round including shipping charges (Rate including shipping charges and conveyance to site).

od81204/2019_2020 : Childrens Play Equipment- Multiplay station including shipping charges (Rate including shipping charges and conveyance to site).

od81205/2019_2020 : Childrens Play Equipment Seesaw including shipping charges (Rate including shipping charges and conveyance to site).

od81206/2019_2020 : Childrens Play Equipment - Expression Swing including shipping charges (Rate including shipping charges and conveyance to site).

Note: 1.Make: Arihant, KHEL, Adithya Swastic or eq. in the order of pref.

2. Material: LLDP/FRP

3. As per approved design and specification , prior approval of KEL/Client and direction of Engineer at site.

od81217/2019_2020 : Retro reflective sign boards made up of 2 mm thick aluminium sheet with pole. As per approved design and specification , prior approval of KEL/Client and direction of Engineer at site. (including all conveyance)

od81218/2019_2020 : Supply and fixing garden pole lights with ms (medium/B class) - pole of 15-18ft height and 42-100mm diameter of type dual arm of micromega, Havells or equivalent brand (LED 20-30 W) with all acessories etc.complete including Civil work, Electrification, Cabling etc. complete (including all conveyance)

od81219/2019_2020 : Construction, Transportation and fixing Rough granite garden benches of size 120x60 cm with all finishings with granite top and side covering etc. complete (including all conveyance)

Construction of Cycle shop with repairing centre

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge (If only, earth is not available at site.)

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size).Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

11.40 : Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of Ist quality conforming to IS: 15622 of approved make in all colours, shades, except white, Ivory, Grey Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.Make: Khajaria, Johnson, RAK, NITCO, Cera or eq. in the order of pref and sample approval from KEL/client.

9.1.2 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal wood

50.9.2.1 : Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge.using Anjili/ Jack wood

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

od80711/2019_2020 : Providing and fixing 60x45x10 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1cement:4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. including sectioning, leveling and consolidation of ground etc. complete as per direction of engineer-in charge including all conveyances.

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes. Make: TATA, JSW, VIZAG, SAIL or eq.

50.9.13.1 : Supplying and fixing Anjily wood wrought and put up for roof members including cost and conveyance of materials etc. complete .

50.9.14.1 : Supplying and fixing Anjily wood reapers of size 50x25 mm with wire nails including cost and conveyance of materials etc. complete.

od80425/2019_2020 : Thatching roof with double new coconut cadjans and Trellising thatched roof with Arecanut 1/3 split reepers at 60cm apart both ways including laying straw over cadjans and covering with fibre net neatly with suitable arrangements as directed by the Architect The rate includes all cost of materials, labour charges, conveyance etc., complete in all leads and lifts for all floors complete. . (PWD Data witlh LMR) (including all conveyance)

od80743/2019_2020 : Providing and fixing in position ceiling work using 12mm thick board: bison board of Multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (high pressure steam cured) as per IS : 14862 with screws (LMR) including aluminium frame work 15 mm thick angle sections of appropriate size as per design and approval. Make with IS. (including all conveyance)

9.105.4 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness partition using 8 mm thick double skin non - asbestos multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (High pressure steam cured) as per IS : 14862 with suitable fibre cement screws.Make with IS as per approved design and specification , prior approval of KEL/Client and direction of Engineer at site.

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work. Make: Asian, Berger, Nerolac or eq. in the order of pref.

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer. Make: Asian, Berger, Nerolac or eq. in the order of pref.

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work. Make: Asian, Berger, Nerolac or eq. in the order of pref.

od80432/2019_2020 : Prepare the surfaces of exposed laterite/brick / RR wall and applying two or more polyurethane based coating of MRF tile garde or approved spray polish over a priming coat with approved shade as recommended by the manufacturer after rubbing, cleaning. The rate includes all cost of materials, labour, scaffolding etc. for all leads and lift at all levels. (including all conveyance)

9.147D.3 : Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Two track two panels sliding window made of (big series) frame 67 x 50 mm &sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazingbead / double glazing bead of appropriate dimension . (Area of window above1.75 sqm upto 2.50 sqm).Make: Sintex with IS or eq.

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness. Make: Saint Gobain,Modiguard or Eq. with IS

od80750/2019_2020 : Polyurethane based Melamine spary polishing : -Two or more coats on new works including a coat of wood filler, melamine primer. Melamine sealer etc.(14.70.1 (derived)) including all conveyance to site.

Construction of toys selling organic kiosk

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge If only, earth is not available at site.

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size). Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

5.3 : Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15⁰ landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more. Make: Tata,Vaishak, SAIL, JSW or eq.

od80426/2019_2020 : Exposed Laterite masonry in CM 1:6 (1 cement : 6 course sand) for superstructure with neatly dressed best quality laterite stones of approved size and quality. The rate includes pointing the joints with matching colour pigment with least thickness. The cost includes all cost of materials, labour charges, conveyance, curing etc. complete as per standard specification. (Observed ) including all conveyance to site.

9.1.2 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal wood

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

50.9.2.1 : Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge.using Anjili/ Jack wood

50.9.4.1 : Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood

9.97.2 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:250x10 mm. Make:INDAL,JINDAL or Eq.

50.9.13.1 : Supplying and fixing Anjily wood wrought and put up for roof members including cost and conveyance of materials etc. complete .

50.9.14.1 : Supplying and fixing Anjily wood reapers of size 50x25 mm with wire nails including cost and conveyance of materials etc. complete.

11.41.2 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. Make: Khajaria, Johnson, RAK, NITCO, Cera or eq. in the order of pref and sample approval from KEL/client.

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

12.48 : Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately)

12.49 : Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ).

od81163/2019_2020 : Polyurethane based Melamine spary polishing : -Two or more coats on new works including a coat of wood filler, melamine primer. Melamine sealer etc.(14.70.1 (derived)) (including all conveyance)

od80432/2019_2020 : Prepare the surfaces of exposed laterite/brick / RR wall and applying two or more polyurethane based coating of MRF tile garde or approved spray polish over a priming coat with approved shade as recommended by the manufacturer after rubbing, cleaning. The rate includes all cost of materials, labour, scaffolding etc. for all leads and lift at all levels. (including all conveyance)

od81183/2019_2020 : Providing and fixing in position ceiling work using 12mm thick board: bison board of Multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (high pressure steam cured) as per IS : 14862 with screws (LMR) including aluminium frame work 15 mm thick angle sections of appropriate size as per design and approval. Make with IS. (including all conveyance)

50.13.1 : 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer. Make: Asian, Berger, Nerolac or eq. in the order of pref.

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).Make: Asian, Berger, Nerolac or eq. in the order of pref.

Construction of Handicraft corner

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge If only, earth is not available at site.

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.9.13.1 : Supplying and fixing Anjily wood wrought and put up for roof members including cost and conveyance of materials etc. complete .

50.9.14.1 : Supplying and fixing Anjily wood reapers of size 50x25 mm with wire nails including cost and conveyance of materials etc. complete.

od80428/2019_2020 : Thatching roof with double new coconut cadjans over the roofing sheet with suitable arrangements as directed by the Architect The rate includes all cost of materials, labour charges, conveyance etc., complete in all leads and lifts for all floors complete. including all conveyance to site.

od81183/2019_2020 : Providing and fixing in position ceiling work using 12mm thick board: bison board of Multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (high pressure steam cured) as per IS : 14862 with screws (LMR) including aluminium frame work 15 mm thick angle sections of appropriate size as per design and approval. Make with IS.(including all conveyance)

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer. Make: Asian, Berger, Nerolac or eq. in the order of pref.

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).Make: Asian, Berger, Nerolac or eq. in the ord

Construction of performing art gallery

60.64.1 : Coconut Pile - Supplying and stacking well matured straight coconut post for driving down throug various strata bellow bed level including cost coveyance labour charges etc complete.(Coconut tree available at island and conveyance will be paid if brought from outside).

60.64.4 : Coconut Pile - Driving down coconut pile to lines and levels through variuos strata including all hire charges and labour for fixing , staging platform and all other appliances necessary for pile driving down after pointing the bottom end

60.64.6 : Cutting and removing the excess length of wooden piles to lines and levels and removing the cut end of piles and stacking within 150m

50.9.13.1 : Supplying and fixing Anjily wood wrought and put up for roof members including cost and conveyance of materials etc. complete .

od80988/2019_2020 : Supplying and fixing Anjili wood planks of 25cm width screwed with 80mm size brass screws in suitable spacings, including cost and conveyence of materials etc. complete. (SI No: derived) (including all conveyance)

od81186/2019_2020 : Supplying and fixing Nut & bolts for fixing planks bressummers etc including cost conveyance and all labor charges etc complete (including all conveyance)

od81096/2019_2020 : Supplying fixing Bamboo balusters and railings for handrails using treated bamboo fixing in position etc complete including cost conveyence and all labour charges etc complete as per drawing and design, 50mm dia bamboos @10cm c/c, top railings etc. as directed by the architectas per approved design and specification , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

od81163/2019_2020 : Polyurethane based Melamine spary polishing : -Two or more coats on new works including a coat of wood filler, melamine primer. Melamine sealer etc.(14.70.1 (derived)) (including all conveyance)

Construction of open air Theatre

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.If only, earth is not available at site and by level calculation.

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size). Cement make: Use Malabar cement only as per Govt. direction and in case of non availabilty of Malabar cement use Ultra Tech, Dalmia, Ramco or eq. brand in the order of preference.

5.1.2 : Providing and laying in position specified grade of Reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size. Assessment of strength of concrete by cube test in Govt. lab.

5.3 : Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15⁰ landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.2.2 : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size). Assessment of strength of concrete by cube test in Govt. lab.

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more. Make: Tata,Vaishak, SAIL, JSW or eq primary make in the order of preferences

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.6.7.1 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.

od80426/2019_2020 : Exposed Laterite masonry in CM 1:6 (1 cement : 6 course sand) for superstructure with neatly dressed best quality laterite stones of approved size and quality. The rate includes pointing the joints with matching colour pigment with least thickness. The cost includes all cost of materials, labour charges, conveyance, curing etc. complete as per standard specification. (Observed ) including all conveyance to site.

9.1.2 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal wood

9.53 : Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

50.9.2.1 : Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge.using Anjili/ Jack wood

50.9.4.1 : Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood

9.97.2 : Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:250x10 mm. Make:INDAL,JINDAL or Eq.

11.20.3 : Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).Dark shade pigment using ordinary cement

13.7.1 : 12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand). (If change in specification, item will be treated as extra).

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer. Make: Asian, Berger, Nerolac or eq. in the order of pref.

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).Make: Asian, Berger, Nerolac or eq. in the order of pref.

14.70 : Melamine polishing on wood work ( one or more coat)

od80432/2019_2020 : Prepare the surfaces of exposed laterite/brick / RR wall and applying two or more polyurethane based coating of MRF tile garde or approved spray polish over a priming coat with approved shade as recommended by the manufacturer after rubbing, cleaning. The rate includes all cost of materials, labour, scaffolding etc. for all leads and lift at all levels.(including all conveyance)

MANGROVE CULTIVATION

od80395/2019_2020 : Planting bamboo at 1 feet interval from existing Kaitha layer towards Land and tying together using bamboo rails of 4 inch diameter in size. The size of plant should be 2-4 feet. (including all conveyance)

od80399/2019_2020 : Cultivation of Kaitha( screw pine) on the banks of shore and binding with 4inch bamboo rails. The size of plant should be at least 2 -4 feet heigh. (including all conveyance)

od80404/2019_2020 : Cultivation of Mangrove saplings 6 feet (Rhizhophora mucronata) in mud filled Bamboo posts of size five inch diameter at a depth of two feet with an interval of one feet. Bind theese bamboo posts using 4 inch diameter bamboo rails (including all conveyance)

Beautification with gardening and landscaping

od81564/2019_2020 : Construction of butterfly garden with suitable landscapes with narrow footpaths 4ft wide with natural stone laying, preparation of land and planting butterfly attracting plants 2-4 ft size like Lantana,Marigold, purple cone flowers , yellow cone flowers, sunflowers, marigolds, poppies, cosmos, salvias, lilies, asters, coreopsis, daisies, verbenas, lantanas, liastris, milkweed, landscaping, grassing,kerb works etc complete including preparation of design and drawing , approval of KEL/Client and direction of Engineer at site. (including all conveyance)

30.2.33 : Providing and fixing Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and even, watering with sprinkler

Construction of granite stone paved cycle riding track

Construction of granite stone paved cycle riding track by providing and fixing 60x45x10cm Granite stone block hand cut and chisel dressed on top, for paving in floors, laid over 100mm thick compacted bed of Stone Aggregate 06 mm nominal size , filling the 10mm joints with fine sand etc. complete as per direction of engineer-in charge. including all conveyance.

Electrification works for balcony, bio toilet, play area, cycle shop, kiosk, handicraft, gallery, theatre, plastic waste etc.Including all conveyance charge and preperation of estimate based on PRICE/PWD schedule, preperation of drawing and getting approval from KEL/client and payment after deducting tender below.

Note: DSR Rate should be inclusive of preparation of schematic diagram and getting approval from KSEB/Electrical Inspectorate. Statutory fees paid to KSEB/EI shall be paid by us separately.

Make of Electrical equipments/materials

All electrical materials/equipments shall be of best branded items with ISI, strictly as per schedule specification

Panel Boards: CPRI certified reputed manufacturers make

MCB/ELCB/DB - L&T/LEGRAND/SCHNEIRDER or equivalent

Cables & wires - Finolex/KEI/POLYCAB/RPG/V-GUARD

Switches/Sockets/Regulators - SCHEIDER/ABB/HAVELS/LEGRAND or equivalent

Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

Cable Glands & Sockets - REPUTED MAKE , Cosmos

Indicating Lamps - TEKINIC/RISHUB/STC, L&T, Schneider or equivalent

Ceiling/Exhaust fan: Havells, Orient, Usha, Crompton Greaves, Bajaj

Push Button- L&T, Schneider, Rishabh

Detailed list of Electrical items attached.

Conveyance Charges by Boat up to 10 KM for Items with DSR only. (For less conveyance, rate shall be revised as per DSR).

Ashlar ,Split stones,Blasted Rubble size above 45dm3

Split stones, Rubble, Aggregates coarse and Fine etc below size of 45 dm3,Laterite, Earth, Gravel etc

Timber, Wood Items etc

Bricks,Roofing Tiles, Ridge,Hip, Flooring tiles (3000 nos / unit)

Cement, Iron Materials, Ac Sheets, Bitumen

Miscellaneous like electrical and plumbing materials etc

Conveyance Charges by Manual Head load up to 500 M. (For less conveyance, rate shall be revised as per DSR).

Ashlar ,Split stones,Blasted Rubble size above 45dm3

Split stones, Rubble, Aggregates coarse and Fine etc below size of 45 dm3,Laterite, Earth, Gravel etc

Timber, Wood Items etc

Bricks,Roofing Tiles, Ridge,Hip, Flooring tiles(3000 nos / unit)

Cement, Iron Materials, Ac Sheets, Bitumen

Miscellaneous like electrical and plumbing materials etc

Conveyance Charges by Lorry up to 10 KM. (Provide only if conveyance is paid by PWD/LSGD for works at Pamthuruthy Island).

Ashlar ,Split stones,Blasted Rubble size above 45dm3

Split stones, Rubble, Aggregates coarse and Fine etc below size of 45 dm3,Laterite, Earth, Gravel etc

Timber, Wood Items etc

Bricks,Roofing Tiles, Ridge,Hip, Flooring tiles(3000 nos / unit)

Cement, Iron Materials, Ac Sheets, Bitumen

Miscellaneous like electrical and plumbing materials etc

General Note:1. All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2.Rate should be inclusive of Transportation, delivery and installation cost for all items and insurance.

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD specification and direction of Engineer at site.

AAYKAYCONSTRUCTIONS

CUBIX INFRASTRUCTURES