EXECUTION OF CERTAIN SANCTIONED WORKS OF AGE B/R-I UNDER GE (ARMY) NO 2 JODHPUR

Amount

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in in cement mortar (1:6) complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry Type C-1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:6 complete all as specified and directed.

Taking down cement plaster of any description and in any position of brick/concrete surfaces on walls/celing etc. including racking out joints, hacking for key, scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed.

S&F GI chicken wire mesh of 0.71mm dia wire & 12mm mesh size fixed with nails & screws around RCC chajjas/fascias etc complete all as specified & as directed.

M&L for rendering 15 mm thick in CM (1:6) on fair faces of stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L 15 mm thick rendering on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished fair and even without using extra cement in CM 1:4.

M&L for rendering 5 mm thick in Cement Mortar (1:4) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces on stone masonry surface, applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) and top layer mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement complete all as specified and as directed.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L vitrified ,coloured and printed tiles of size 600 mmx600 mm x 10 mm thick as in flooring over and including 15 mm thick cement screed in (1:6 ) CM set and jointed in neat cement slurry set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L vitrified ,coloured and printed tiles of width as directed and 8 to 9 mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. over and including 15 mm thick cement screed in (1:6) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match and pointed in white or coloured cement to match the colour of tile complete all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tile colour laid over and including 10 mm thick screed / rendering in CM (1:4) complete all as specified and directed.

Taking down existing chowkats or frames of any description and in any position not exceeding 1.50 sqm each with shutter (w/o taking off shutter from the frames) complete all as specified and directed.

Taking down existing chowkats or frames of any description and in any position exceeding 1.50 sqm but not exceeding 4 sqm each with shutter (w/o taking off shutter from the frames) complete all as specified and directed.

Taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each.

S&F pressed steel frames of size 165x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

M&L for PCC 1:2:4 type B0 (using 12.5 mm crushed stone aggregate) as in concrete filling in pressed steel door frame complete all as specified and directed.

S&F 35mm thick factory made Plain, framed, 1st class softwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, both faces is covered with commercial type and including S&F 0.9mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instruction with lipping/frame to match complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed.

S&F Powder coated (minimum thickness of powder coating 50 micron ) aluminium frame for doors , windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified by Engr-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings & specified & directed at site.

S&F in repair hydraulic door closer aluminum body fixed in repair design No 3 universal type, suitable for door shutter all as specified and approved sample.

S&F 4 levers brass mortice lock, vertical type, size 100 mm complete all as specified.

S&F 150 mm long aluminium anodised , barrel tower bolt of extruded section and fixed all as specified and directed.

S&F aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S & F butt Hinges, medium weight, stainless steel,100 mm size complete all as specified.

S&F 200 mm long aluminium anodised , barrel tower bolt of extruded section and fixed all as specified and directed.

S&F 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

Taking down steel windows/ ventilators and making good & sorting of materials & remove from site complete all as specified.

M&L for factory made box type steel window ( Glazed Steel Window) with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer (with or without cooler opening) complete all as specified and directed.

M&L for factory made box type steel window ( Fly Proof Steel Window) with pintel hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer(with or without cooler opening) complete all as specified and directed.

M&L for factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed.

Supply and fabrication of framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, cooler stand and similar work conforming to Fe.290.Gde-E-165

S&F 3mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed.

S & F 3 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as directed.

Preparation of new surface of wood and wood based material any description and in any position over 10 cm width or girth and M&L for applying two coats of synthetic enamel paint over a coat pink primer all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surfaces and apply two coats of synthetic enamel paint over a coat of red oxide primer over 10 cm in width or girth of surfaces complete all as specified and directed.

Supplying and fixing stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, wooden beads etc complete all as specified and directed

Dismantling water tanks of any description in any position exceeding 250 & not exceeding 500 lit capacity complete all as specified and directed.

Dismantling water tanks of any description in any position exceeding 500 & not exceeding 1000 lit capacity complete all as specified and directed.

S&F Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 500 litres capacity, of any colour hoisted and fixed in position with and including all fittings and fixtures in repairs complete all as specified and directed.

S&F Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 1000 litres capacity, of any colour hoisted and fixed in position with and including all fittings and fixtures in repairs complete all as specified and directed.

S&F 20mm ball valves high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed/fixed to pipes/ferrules .

S&F in repair vitreous china squatting pan, Orissa pattern, size 580 x 440 mm white with integral foot rests and connection to trap and to flushing pipe, anti syphonege pipe etc complete including taking down existing WC & fixed new WC in repair including making good the disturbed surfaces to match with existing surfaces complete all as specified and directed.

S&F in repair Vitreous China, wash down water closet pan "Pedestal pattern" white including connection to drain and to flush pipe and anti syphonic pipe including all joints and making good the disturbed surfaces complete all as specified.

S&F in repair PVC valve-less, syphonic action type, flushing cistern, low level, 10 litre capacity (ISI marked) white with inlet, ball valve, float and handle including brackets & flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed.

S & F vitreous china wash basin,white flat back , size 550mmx450mm with and including Waste fittings, brass, chromium plated for basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with and including Supplying and fixing cast copper alloy chromium plated, fancy type, pillar tap, 15mm bore, scrwed down high pressure with or without lettereed hot or cold with long shanks, screwed for iron pipe complete all as specified and directed as in repair.

S&F bib tap in repair, cast copper alloy, screwed down high pressure with crutch of butter fly handle fancy type CP for 15 mm bore dia. complete all as specified and directed.

S&F chromium plated concealed type stop valves in repair, ISI marked , cast copper alloy, screwed down high pressure for 15 mm bore dia GI tubing pipe, high pressure, with crutch butter fly handle complete all as specified

S&F chromium plated angular type valves in repair, ISI marked , cast copper alloy, screwed down high pressure for 15 mm bore dia GI tubing pipe, high pressure, with crutch butter fly handle complete all as specified

S&F in repair for Swivel shower rose of PTMT , any colour , for fixing with 15 mm dia pipe ,( minium weight 40 gm. ) with and including Shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of PTMT any colour (Min wt 40gms) , fixed in repairs , complete all as specified and directed .

S&F grating doom 100 mm dia of PTMT Min wt 25 grams etc

S&F as in repairs Corner Glass shelf 250mm superior quality with CP tubular framing & brackets complete all as per sample kept in GE's office.

M&L for 18-20 mm thick Black granite stone as in cooking platforms, slabs for oval type WHB,sinks/window & door cills etc & the likes complete laid over 15 mm thick in CM 1:4 incl mirror polishing complete & providing necessary holes for gas pipe / water supply pipes etc and rounding of the edges of stone slabs as in cooking platforms all as directed at site.

Taking up or down steel tubing and connection of 20 mm bore tube of any description & in any position complete all as specified and directed.

Ditto as above but 25 mm bore tubing.-ditto-

Supply and fixing 20 mm dia (nominal)3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed

Supply and fixing 25 mm dia (nominal)3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed

S&F tubular towel rail of brass chromium plated , 20 mm dia, D type, 60 cm long betweem flanges complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size 75mm to 110mm of any pattern) ,of any description and in any position, including all fittings , heads, shoes, bends, swan necks, etc., (measured overall as fixed along the centre line over fittings and accessories)complete all as specified.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed on walls complete all as specified and directed

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed on walls complete all as specified and directed

Supply and fixing in repairs decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia with best quality knob metal as per sample kept in GE's office.

Supply and fixing in repair purpose made brackets trade pattern for decorative type curtain rods suitable for holding 22 to 25 mm dia as per sample as in repairs kept in GE's office.

Supply and fixing in repair of decorative fincals (round type with mirror optic finish) trade pattern for decorative type curtain rods suitable for 22 to 25 mm dia curtain rods as per sample kept in GE's office.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets

M&L Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

M&L for 12mm thick perforated particle board/ tiles for insula-tion and accoustic purposes, 60x60 cm in size, fixed in ceiling in GI frame work or with staples on snap grid complete all as specified & directed.

M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for preparation of newly plastered surface and apply a coat of primer and over including two coats of distempering consist of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. including a layer of 1mm thick birla white putty to make the surface become smooth complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfacescomplete all as specified and directed.

M&L for demolition of concrete of any description and in any position not otherwise specifically provided for complete all as spd

Taking down of existing damaged / loosened cement concrete/ brick tiles from roof / terrace to a depth of average 50 mm including taking down of existing APP membrance if any , cleaning with water and depositing of debris to a distance not exceeding 50m complete all as specified & as directed by Engineer-in-Charge

M&L for 15mm rendering in cement mortar 1:4 mixed with WPC @3% by weight of cement shall be provided at green concrete complete all as specified & as directed

M&L for Bituminious Primer confirming to IS 3384 @ 0.40Litre per Sqm complete all as specified and directed complete all as spd

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface of blown bitumen confirming to IS 702-1988 grade 85/25 @ 1.2kg per sqm by forced application complete all as specified

M&L for PCC 1:2:4 Type B-1 (using 20mm graded stone aggregate ) average 25mm thick in padding over old cleaned surface of any description on roof / terrace

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) etc.complete all as specified and directed.

S&F 5 cm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, & in plinth protection templates, etc n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed cement mortar 1:4. complete all as specifed.

M&L for 50 mm thick Cement concrete type C1 (using 1:3:6 using 20mm graded stone agg) as in plinth protection & finishing the surface even & smooth w/o using extra cement complete all as specified and as directed.

M&L for 75 mm thick PCC , (1:4:8) type D-2, (using 40mm graded stone aggregate) as in sub base for floor complete all as specified and directed.

Material and labour for 60 mm thick, machine made ,1st quality, precast cement concrete rubber moulded coloured interlocking paver blocks / tiles , of triangular / Zigzag / Haxagone/ I , in shape or shap and designe as approved, with grey cement and pigment , having crushing strength not less than 300 Kg / Sqcm and conforming to IS specifications , laid over and including a layer of 25 mm thick sand cushion including filling the joints with sand , as in floors/ paths/ pavings etc, complete all as specified and directed.

M &L in repair for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape incl two coats of synthetic enamel paint on internal surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete all as specified and directed. (Note:- Taking down of existing Cupboard /Almirah is deemed to be included in the quoted rates)

Supply only Integral waterproofing compound complete all as specified & as directed by Engineer-in-Charge

Surface execavation not exceeding 30 cm deep and averaging 15 cm deep.

Excavation over areas n.exc 1.5m deep and getting out in soft/loose soil.

M/L for PCC type D2 1:4:8 (using 40mm graded aggregate) as in foundation filling and mass concrete.

M&L for squared rubble stone wallingJodhpur type,regular coursed,well bonded, bedded and solidly hearted,built in CM(1:6) complete all as specified and directed.

Extra over stone masonry for hammer dressing to facestones with maximum depression on face from a straight edge held against the dressed surfaces not exc 20mm and dressing face beds and joints as specified to squared rubble walling, Jodhpur type, regular coursed complete all as specified and directed.

M&L for prep of old and new surfaces of walls & applying two coats of cement base paint over a coat of primer complete all as specified.

M&L forming embankments including raising earth spreading in layers n exc 30 cm thick , watering ramming /rolling and finishing to requied size , shape etc n exc 1.5 m ht from base

M/L for hardcore of gauge exc 63mm but n.exc 100mm, deposited, spread and levelled in layers n.exc 15cm thick watered and rolled/ rammed to a true surface.

M&L 150 mm thick PCC 1:4:8 type C2 using using 40mm graded stone aggreagte as in subabse.

M&L 150 mm thick PCC 1:2:4 type B2 using using 40mm graded stone aggreagte as in sub base.

M&L for Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ slab thickness 150 mm

Taking down carefully aluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site as directed.

M&L for taking down carefully of existing serviceable Old ceiling/Exhaust Fans and re-fixing the same with extension GI rod at appropriate locations including all electric connections, oiling & servicing ,pipe fittings with required accessories like clamps, nuts, bolts, fastners etc., complete all as specfied and directed by Engr-in-Charge.

M&L for point wiring complete for one light point / fan point / bell point controlled by one 1-way switch/ bell push, with 1.5 Sq mm (nominal area) FRLS PVC insulated un-sheathed and stranded copper conductor cable ISI marked and PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers with and including FRLS PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size for fixing modular switches / sockets etc and making good surface by wall panelling etc, complete all as directed.

All as per srl item No. 106 here-in-before but for one socket outlet 3 pin, 5 Amps on independent board.

All as per srl item No. 106 here-in-before but for one socket outlet 3 pin, 5 Amps on same board.

All as per srl item No. 106 here-in-before but with 4 sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for one 3 pin socket outlet 15 amps independent or any other outlet complete all as specified and directed by Engr-in-Charge

S & F Modular switch 1 way 6A , 1 module size complete all as directed.

S & F Modular switch 1 way 16 A , 1 module size complete all as directed.

S & F Modular Socket , 6 A , 5 Pin , 2 module size complete all as directed.

S & F Modular Socket , 6 A / 16 A , 5 Pin , 2 module size complete all as directed.

S& F Modular type regulator 2 module A/C 240 Volts

S&F of Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed.

S & F Lamp holder, PVC/Polycarbonate type with LED Bulb and back plate suitable for batten fittings complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F of LED light fitting 1 X 20/22 watt (4 feet), decorative ultra slim type, with inegral driver, complete with all accessories and making necessary electric connection from ceiling rose to fitting terminal, complete all as specified and directed.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.Note:-The cost supplying and fixing iron bracket 32 mm bore with necessary nut bols ,clamp etc is included in quoted rate.

S&F Vertical TPN 4 way Distribution Board after taking out old unsv DB , double Door, suitable for MCCB's upto 125A as I/C made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, 415 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and MCCB etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Note : MCCB & MCB will be measured and paid separately under respective items

S&F of Distribution Board, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 08 way (Concealed flush to wall), 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.

S&F of MCCB, A Frame, thermal adjustable magnectic setting, Ics = 75% 25 kA, 415V, 125 Amp, 4 Pole MCCB with over load and short circuit protection, complete all as directed.

S&F of MCB, C Curve type, 10 kA, 40-63Amp, SPN with over load and short circuit protection, complete all as directed.

S&F of MCB, B Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed.

S&F of MCB, B Curve type, 10 kA, 40 Amp, Single Pole with over load and short circuit protection, complete all as directed.

Taking down old sub main wiring and M&L for concealed sub main wiring with 2 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 20 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note : Two run of 6 Sq.mm. and one run of 6 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces.

Supply, laying, testing and commissioning of LT UG cable, XLPE insulated, PVC sheathed, galvanized steel strip armoured electric power cable with stranded aluminium conductor, 1100 volts grade of size 25 sqmm 4 core, suitable for earthed system, laid in duct/trench/along pole/wall etc including nuts, bolts, washers, saddles & screws etc and making connection, complete all as directed. Note : 1. The cost of Al thimbles/lugs and cable gland etc is included in quoted rate and no extra payment will be made for it. 2. Excavation, earth work, sand cushioning and brick protection will be measured and paid separately under respective items.

Excavation in trenches in Soft / dense soil not exceeding 1.5 meter depth and not exceeding 1.5 meter wide and getting out including trimming of sides, complete all as directed.

Removing excavated material to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point, complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick, complete all as specified

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm under ground cables for protection

M&L for sand cushioning with layer of sand 8 cm thick before laying of cable and 10cm after laying of cable in trenches complete all as directed and sand cover to under ground cable complete all as directed.

M&L for Cutting of road/hardstanding not more than 30 cm deep 45 cm wide for crossing of cable/ pipe line in trenches and making the surface good with PCC(1:2:4) type B-1 using 20 mm graded aggregate complete

Supply & Laying steel tubing 'light grade 'galvanised 50 mm bore with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed.

Supply & laying steel Tubing galvanized medium grade (ISI Marked) 25 mm bore and tube fittings ISI marked laid in trenches all as specified and directed by Engineer-in-Charge.

Supply and fix Valve stop,Screwed 25 mm bore pipe complete all as speciifed and directed by Engineer-in-Charge

M & L for Cutting existing water supply CI/DI pipe line of upto 80 mm bore and taking branch connection of 25 mm bore pipe by inserting suitable size tee for tapping including fitting joints complete all as specified and directed by Engineer-in-charge

M/S KAUTILYA GARG (BID ID -3299197)

Pawan Kumar Shrama Contractor (BID ID -3305472)

Diva Infra (BID ID -3300782)

Harsh Enterprises (BID ID -3306475)

Bhairav Infra Projects (BID ID -3301150)

Ashwani Associates (BID ID -3300813)

JB INFRA (BID ID -3299344)

M/s Ajay kumar Garge (BID ID -3301142)

Nikhat nirman (BID ID -3306341)