Construction of 20 bedded Female Barrack at Sub Jail Nerchowk District Mandi HP including internal and external water supply sanitary installation and construction of 5000 ltrs capacity rain water harvesting tank

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron frames 30x30x5mm so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies heights of propping and centering below supporting floor to ceiling in all heights and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials in all leads and lifts:-

Foundation, footings, bases of columns etc. and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like floors etc. up to 200 mm in thickness.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like.

Columns, pillars, posts and struts:- Square, rectangular or polygonal in plan.

Stair cases with sloping or stepped soffits excluding landing.

Beams, cantilever, girders and lintels:- Sides and soffits of beam, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 mtr in depth in all heights from floor.

Edges of slabs and breaks in floors and walls:- Under 20 cm. wide.

Providing and laying cement concrete 1 : 2 : 4 (1 cement:2 sand:4 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts.

Providing and laying cement concrete 1:4:8 (1cement:4sand: 8graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts.

Providing and laying cement concrete 1:6:12(1cement:6sand:12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centering and shuttering in foundation and plinth including carriage of material in all leads and lifts.

Providing and laying mechanically mixed vibrated reinforced concrete of mixed design to have characteristics strength of M-20 GRADE and curing complete to give a smooth and even surface including the cost of form work but excluding the cost of reinforcement for reinforced concrete work including carriage of material in all leads and lifts:- Mouldings as in cornices, windows sills etc. not exceeding 15 cm. in girth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level including carriage of material in all leads and lifts.

1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) including carriage of material in all leads and lifts.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) including carriage of material in all leads and lifts.

Providing & laying T.M.T./Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire upto all heights including carriage of material in all leads and lifts.

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg of cement per sq. metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surface complete including carriage of material in all leds and lifts.

Providing throating or plaster drip and moulding to R.C.C. chajjas including carriage of material in all leads and lifts.

Providing and laying cement concrete 1:8:16 (1cement:8sand:16 graded stone aggregate 20 mm nominal size) and curing complete on slab and floor excluding the cost of form work screed laid under flooringincluding carriage of material in all leads and lifts.

Brick work using 2nd class common burnt clay building bricks in superstructure above plinth level up to all heights, in cement mortar 1:6 (1cement:6sand), including carriage of material in all leads and lifts.

Half brick masonry using 2nd class common burnt clay building bricks in superstructure above plinth level upto floor all level in cement mortar 1:4(1cement:4sand) including carriage of material in all leads and lifts.

Boulder filling dry hand packed tightly as in and under floors including watering, ramming and consolidating complete including carriage of material in all leads and lifts.

Random rubble masonry/polygonal rubble masonry (Uncoursed/ brought to courses) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1cement:6sand:12graded stone aggregate 20mm nominal size) in cement mortar 1:6 (1cement:6sand) includuing carriage of material in all leads and lifts.

Providing and fixing oxidised MS sliding door bolts of required color and shade with bolts and nuts, screws etc complete including carriage of material in all leads and lifts.

Providing and fixing oxidised MS tower bolts (barrel type) of required shade and colour with screws, etc. complete including carriage of material in all leads and lifts.

Providing and fixing oxidised MS handles to required colour and shade with necessary screws, etc. complete including carriage of material in all leads and lifts.

Providing and fixing oxidised MS hooks and eyes:- 150mm including carriage of material in all leads and lifts.

50 mm thick cement concrete flooring 1:2:4(1 cement:2sand:4gradedstone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement,including carriage of material in all leads and lifts.

40 mm thick marble chips flooring rubbed and polished to granolithic finish under layer 28 mm thick cement concrete 1:2:4 (1 cement 2 sand 4 graded stone aggregate 10 mm) and down guage and top layer 12mm thick marble chips of required sizes laid in cement marble powder mix 3:1 ( 3 cement :1 marble powder by weight) in proportion of 4:7 (4 cement marble powder mix 7 marble chips by volume)including carriage of material in all leads and lifts:- Medium shade pigment with approximately 50% white cement and 50% & ordinary cement (in top layer only).

Marble chips skirting or dado upto 30 cm. height (rubbed and polished to granolithic finish) laid in cement marble powder mix 3:1 (3 cement :1 marble powder by weight) in proportion of 4:7 (4cement marble powder mix: 7 marble chips by volume) in top layer including carriage of material in all leads and lifts:- Medium shade pigment with approximate 50 % white cement and 50 % ordinary cement (in top layer only).

Kota stone slab flooring 20mm (average) thick base of cement mortar 1:4 (1cement:4sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete 25mm thick including carriage of material in all leads and lifts.

Kota stone slab 25mm thick in risers of steps skirting dado and pillars laid on 12mm (average) thick cement mortar 1:3(1cement:3sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including carriage of material in all leads and lifts.

Providing and laying granite stone in flooring 20mm (average) thicknss base of cement mortar 1:3 (1cement:3sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete 20mm thick including carriage of material in all leads and lifts.

Extra for providing moulding to strips of granite stone including making nosing of stair case steps fixing with Areldite all complete as per drawing and instructions of Engineer- In- Charge.

Providing and fixing Digital tiles 30cm x 45cm and 8mm thick in any colour of approved shade in skirting, riser of staps and dado on 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the tiles including carriage of material in all leads and lifts.

Providing and fixing marble strips 40mm wide and 15 mm thick painted with protective coat of bitumen joints of cement concrete flooring, including carriage of material in all leads and lifts.

Painting top of roofs with bitumen of approved Quality at 17 kg. for 10 sqm. Impregnated with a coat of sand at 0.06 cum per 10 sqm. Including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete including carriage of material in all leads and lifts:- Wtith residual type petroleum bitumen of penetration 80/100.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm diameter with prepainted limpet and rubber washer complete with all accessories as required as per the direction of Engineer-in-charge including carriage of material in all lead and lifts.

Providing and fixing ridges or hips 60cm over all with 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm diameter with prepainted limpet and rubber washer complete with all accessories as required as per the direction of Engineer-in-charge including carriage of material in all lead and lifts.

Providing and fixing flushing 38cm over all with 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm diameter with prepainted limpet and rubber washer complete with all accessories as required as per the direction of Engineer-in-charge including carriage of material in all lead and lifts.

Providing and fixing 15 cm. wide 45 cm overall semi circular plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary connections with rain water pipe complete as per design 0.63mm thick sheet including carriage of material in all leads and lifts.

Steel work welded in built up sections trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of material inn all leads and lifts:-

In beams, joists, channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters, purlins connected to common rafters and the like.

In gratings, framed guard, bars, ladders, railings, brackets and similar work.

Providing and fixing 1 mm thick M.S. sheet door & window shutters with frame of 40x40x6mm including welding of necessary fitting complete including a priming coat red lead paint (M.S. fitting such as door bolts, tower bolst and handles will be paid separetly) including carriage of material in all leads and lifts.

Proiding and fixing on wall face P.V.C. rain water pipes of working pressure not less than 4.5kg per sqm. including filling the joints with approved adhesive complete including carriate of material in all leads and lifts:- 100mm dia.

Providing and fixing M.S.holder bat clamps of approved design to C. I. or S.C.I./PVC pipes embeded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1cement:2sand:4 graded stone aggregate 20mm nominal size) and cost of cutting holes and making good the wall etc. including carriage of material in all leads and lifts:- 100mm diameter.

Providing and fixing on wall face P.V.C. accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of material in all leads and lifts:-

P.V.C. Plain bend 100mm diameter

P.V.C. plain shoe 100mm dia.

Painting (two coats) (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give fair and smooth surface including cleaning the surface of all dirt, dust, dust and other foreign matter. Enamel paint other than white including carriage of material in all leads and lifts.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board / facia / soffits / ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in charge, (Base members of steel work shall be measured and paid separately) including carriage of material in all leads and lifts.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other forein matters sand papered smooth to give final matter finish to the surfacae complete including carriage of material in all leads and lifts.

6mm cement plaster to ceiling in cement mortar including carriage of material in all leads and lifts. In cement mortar 1:3(1cement:3sand).

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering up to all heights including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts:-

In cement mortar 1:3(1cement:3sand).

In cement mortar 1:6(1cement:6sand).

Extra for cement plaster for finishing with a floating coat of neat cement slurry including carriage of material in all leads and lifts.

20mm cement plaster in single coat on rough side of brick/stone masonry for interior plastering up to all heights including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth including carriage of material in all leads and lifts:- In cement mortar 1:6 (1cement:6sand).

Add extra over item of cement plaster/concrete/plain R.C.C. work providing and mixing of synthetic fibre 6mm/12mm Recron 3.5 @ 125 gram pack per 50 kg of cement or in ratio as specified by manufacture specification and direction of the Engineer-in-charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equrlied on undecorated wall surface to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete including carriage of material in all leads and lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6(1 cement : 3 sand :6graded stone aggregate 20mm nominal size) including finishing the top surface of concrete smooth including carriage of material in all leads and lifts.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed of dry bricks/stone aggregate 40mm nominal size) well rammed and consolidated and grouted with fine sand including preparation of ground including carriage of material in all leads and lifts.

Brick edging brick laid on edge to plinth protection with bricks including grouting with cement mortar 1:4(1cement:4sand) with brick size 22.9cmx11.2cmx7 cm. including carriage of material in all leads and lifts.

Constructing course rubble hammer dressed “U” shape open surface drain with side wall 15x22cm in cement mortar 1:6(1cement:6sand) and inside plastering with cement mortar 1:3(1cement:3sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1cement:5sand:10graded stone aggregate 40mm nominal size) and 7.5cm cement concrete 1:2:4(1cement:2sand:4graded stone aggregate of 20mm nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads and lifts.

Providing chases 75mm wide and 50mm deep (average size) in walls for G. I./C. I. pipes and filling the same with cement concrete 1:3:6 (1cement:3sand:6graded stone aggregate 20mm down gauge after the G. I./C. I. pipe is laid (excluding the cost of G. I./C. I. pipe) including carriage of material in all leads and lifts.

Providing and fixing 10mm thick antiskid water proof stain and impact resistent heavy duty vetrified tiles Nitco or equivalent 600x600mmx10 manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1cement:3sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required including carriage of material in all leads and lifts.

Providing and laying Duro stone vetrified tiles 10mm thick any size and coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1cement:3sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts.

Providing and laying Duro stone vetrified tiles 8mm thick any size and coloured of required shadae in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (1cement:3sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of material in all leads and lifts.

Providing and fixing hydraulic door closer of Everest make and manufacture complete including carriage of material in all leads and lifts.

Providing and fixng 100mm bright finished stainless steel powder coated floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of material in all leads and lifts.

Providing and fixing to wall ceiling and floor E.E. Lythelene- Aluminium- E.E. Lythelene (PE-AL-PE) com. E.E. site pressure pipes confirming to IS-15450, U.V. stablized with carbon black having thermal stability for hot and cold water supply, capable to withstand temprature up to 80 degree C, including all special fittings of com. E.E. site material (engineering plastic blend and brass inserts whereever required) e.g. elbows, tees, reducers, couplers and connectors etc; with clamps at 1.0 metre spacing. This includes testing of joints complete as per direction of the Engineer-In- charge, including carriage of material in all leads and lifts.

1216 (16 mm OD) pipe

2025 (25 mm OD) Outer dia.

Making connection of galvanized steel distribution branch with galvanized mild steel main 20 to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of material in all leads and lifts.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G. I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level including carriage of material in all leads and lifts. (a) 1000 liters net capacity.

Providing and fixing high pressure PVC spigot and socket soil waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts:-

110mm dia.

75mm dia.

Providing and fixting PVC clamp ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material in all leads and lifts.

110mm dia.

75mm dia.

Providing and fixting PVC door bend with oval access door, ISI marked insertion rubber washers 3mm thick bolts and nuts including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110mm dia.

75mm dia.

Providing and fixting PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110mm dia.

75mm dia.

Providing and fixting single equal branch with oval access door, ISI marked insertion rubber washers 3mm thick bolts and nuts including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110mm dia.

75mm dia.

Providing and fixting PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110mm dia.

75mm dia.

Providing and fixting PVC cowl ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts:-

110mm dia.

75mm dia.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the walls and floors complete. 110mm x 75mm including carriage of material in all leads and lifts.

Providing and fixing stainless steel wash down water closet (European type W.C. pan) with integral "P" or "S" trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement:1sand) including all accessories complete including carriage of material in all leads and lifts:- Anglo Indian (Universal closet), (confirming to BIS specification).

Providing and fixing steel wash down, water closet squatting pan (Indian type W.C pan) size 580mm including flushing cisten, P" or "S' trap including all accessories complete including carriage of material in all leads and lifts.Orissa Pattern.

Providing and fixing stainless steel wash basin with single/double hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings including carriage of material in all leads and lifts:- Flat back 550mmx400mm.

Providing and fixing C.P. brass towel rail complete with C.P. brass brackets fixed to wooden plugs with C.I. brass screws, including carriage of material in all leads and lifts. (i) 750mm x 20mm

Providing & fixing C.P. brass toilet paper holder including carriage of material in all leads and lifts:.

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws including carriage of material in all leads and lifts.

Providing and fixing stainless steel kitchen sink of approved standard (ISI make) with drain board and C.P. waste including cost of C.I. o r M.S. brackets painted white including cutting holes in walls and making good the same but excluding fittings including carriage of material in all leads and lifts:- 610x510mm with bowl depth 200mm.

Providing and fixing C.P. brass bib tap with capastan head including carriage of material in all leads and lifts confirming to BIS specification:- 15mm dia.

Providing and fixing C.P. brass pillar tap with capastan head including carriage of material in all leads and lifts confirming to BIS specification:- 15mm dia.

Providing and fixing C.P.brass angle valve15mm without nuts & pipe confirming to BIS specification including carriage of material in all leads and lifts.

Providing and fixing C.P.brass consealed stop cock 15mm dia confirming to BIS specification including carriage of material in all leads and lifts.

Providing and fixing chromium plated stainless steel grating 100mm of superior quality for floor, gully or nahani trap confirming to BIS specification including carriage of material in all leads and lifts.

Providing and fixing brass full way valve with wheel confirming to BIS specification including carriage of material in all leads and lifts:-

15 mm nominal size

25 mm nominal size.

Providing and fixing G.I./M.I. unions of following sizes(where not included in the item) including carriage of material in all leads and lifts confirming to BIS specification:-

15mm nominal size

25 mm nominal size.

Providing and fixing PVC connection pipe with brass union 300/450 mm length and 15mm nominal bore including carriage of material in all leads and lifts confirming to BIS specification.

Providing and fixing P.V.C. plastic waste pipe for wash basin or sink of following size BIS specification including carriage of material in all leads and lifts. (a) 32mm mm dia.

Providing and fixing stoneware gully trap grade ‘A’ complete with C.I. grating, brick masonry chamber in cement mortar 1:6(1cement:6sand) and water tight C.I. cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53kg and frame to be not less than 2.72kg) square mouth trap 100mmx100mm size 'P' type including carriage of material in all leads and lifts confirming to BIS specification.

Cutting holes through existing brick/stone walls including making good the same in cement mortar 1:6(1cement:6sand) per cm depth of cutting: Holes up to and including 400 mm square centimeter in area including carriage of material in all leads and lifts.

Constructing manhole with RCC top slab in 1:2:4mix(1cement:2sand :4graded stone aggregate 20mm nominal size) foundation concrete 1:4:8(1cement:4sand:8graded stone aggregate40mm nominal size) inside plastering 15mm thick with cement mortar 1:3(1cement:3sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4mix (1cement:2sand:4graded stone aggregate 20mm nominal size)finished smooth complete including curing and testing including carriage of material in all leads and lifts:

Inside size 800mm x 800mm x 500mm deep including S.F.R.C cover with frame (light duty) total weight of frame and cover to be not less then 173 kg weight of frame 103 kg weight of cover 70 kg with 230 mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3(1cement:3sand). including carriage of material in all leads and lifts.

Inside size 800mm x 800mm x 1000mm deep including S.F.R.C cover with frame (light duty) total weight of frame and cover to be not less then 173 kg weight of frame 103 kg weight of cover 70 kg with 230 mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3(1cement:3sand). including carriage of material in all leads and lifts.

Providing and fixing 200 mm wide cast iron rungs with cheque-red or ribbeed non slip surface including fixing in manholes with 200 mm x 200 mm x 100 mm cement concrete 1:3:6 (1cement : 3sand : 6 graded stone agg. 20 mm nominal size) including carriage of materials in all leads and lifts.

Supplying cast iron cover with frame for manholes for frame of 500mm internal diameter C.I. cover (medium duty) the weight of cover to be not less than 58kg. including carriage of material in all leads and lifts.

Pankaj Gupta

Rajesh Kumar