GE-K-43-2023-24 - SPECIAL REPAIR TO BLDG NO T-20 AND T-24 OF 308 FD HOSP AND PROVN OF UTENSIL WASHING AREA WITH SHED AT BLDG NO T-15 (JCOs MESS) AT 308 FD HOSP, DRAS UNDER GE KARGIL

Amount

Dismantling of plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws as specified

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws as specified

S&F 0.63mm thick, galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or crancked hook bolts and washers as in roofs, walls etc, with grade of zinc coating 275, complete all as specified and directed

All as per item No-4 here-in-before but except sheet

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and as directed by Engr-in-Charge

S&F Rolled mild steel Gde Fe-290 (gde E-165) as in Roof trusses (framed), trussed, purlins crane gantries, rails & fastenings & heavy brackets framimg (Beam, tee, angle, channel or flat section) including distance pieces, cleats etc.

Demolition of stone slabs and tiles of any description or thickness in floor, aprons etc laid, bedded and pointed in any mortar complete all as specifed and as directed

Demolition of Cement Concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below or above ground level) complete all as specified and as directed

M&L PCC 1:3:6 type C1 ( using 20 mm grade aggregate) 75 mm thick as in sub base/plinth protection/paving complete all as specified and as directed

M&L PCC type B0 1:2:4 (12.5mm graded aggregate) 25mm thick as in floor finished surfaces fair and even to receive tile all as specified and as directed

M&L screed bed or bedding layer of cement mortar 20mm thick in CM 1:4 for laying floor finishes to receive kota stone all as specified and as directed

M&L machine cut Kota stone slab flooring 20-25mm thick, over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed

M&L for Chequered cement concrete tiles 30cmx30cmx25mm thick, etc, jointed and pointed in neat cement slurry in floors with grey cement and no pigment over 20mm screed bed in CM 1:6 complete all as specified and as directed

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/blankets, any thickness, including cover fillets all as specified and as directed by Engr-in-Charge.

Dismantling fillets timber scantling as in fillets, rails, posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and as directed b Engr-in-Charge

M&L for Plain fillets of second class soft wood (KAIL), sectional area exceeding 13 Sqcm but not exceeding 25 Sqcm in square, rectangular or traingular in section, clean sawn secured with nails or brads complete all as specified and directed

M&L for Plain fillets of second class soft wood (KAIL), sectional area exceeding 3 Sqcm but not exceeding 6 Sqcm in square, rectangular or traingular in section, bullnosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed

S&F 12 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber rame work complete, all as specified and directed

S&F 9 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber frame work as in ceiling complete all as specified and directed

Hacking out old broken glass panes (any thickness size quality or description ) from metal frame including punching or drilling out old glazing pins/spring clips and proving and fixing news one complete all as specified and as directed

S & F 4mm thick glass pan ordinary quality and glazing with oil putty in square not exc 0.5 sqm each pane.

M&L for easing of steel window/door for necessary welding for hinges, tower bolt, handle and sliding bolt if required and ensure free movement opening/closing of door/window complete all as specified and as directed by Engr-in-Charge

M&L preparation of new or previously untreated surfaces of steel and applying two coat of Synthetic enamel paint over a coat of red oxide primer incl preparing new zink or galvanised surface by coating mordant solution on CGI/PGI Sheets.

M&L preparation of old surfaces of steel and applying two coat of synthetic enamel paint complete all as specified and as directed.

M&L for surface dressing n.exc 15 cm deep and getting out in hard/dense soil

Excavating in trenches n exc 1.5 m in depth for foundation, & n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out in hard / dense soil

M& L PCC 1:4:8 type D-2 (using 40mm graded stone agg) in foundation, filling and mass concrete.

M&L precast cement concrete type C-1, 1:3:6 using 20mm graded stone aggregates, block masonry with solid blocks, exc 10cm width andsetting cement mortar 1:6 complete.

Returning filling incl spreading leveling watering and well ramming in layers not exceeding 25 mm in any type of soil.

Removing excavated material n.exc. 50 m and deposited were directed at a level n.exc.1.5 m above the starting point

M & L rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces, finishing even and smooth without using extra cement complete all as specified and as directed

M & L rendering 15 mm thick in CM 1:4 on other fair faces of brick work or concrete surfaces in two layers 10mm & 5mm thick, finishing even and smooth without using extra cement complete all as specified and as directed

Form work to edges of concrete flat, treads, window cill, floor and roof etc n.exc 20cmm wide and sided of RCC /PCC bands in walls, horizontal or sloping and similar work exc 10cm but n.exc 20cm wide in rough finished surface of concrete complete all as specified and directed by Engr-in-Charge.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work not exc 200mm thick (Horizontal or sloping) in flat rough surface of concrete complete all as specified and directed by Engr-in-Charge.

M&L mild steel TMT bars 10 mm dia and over cut to length bent to shape required inclduing cranking bending spirally for hooping ends and binding with and incl mild steel wire (annelaed) not less than 0.90 mm dia or securing with clips.

M&L for reinforcement cement concrete (nominal mix) type B1 1:2:4 (using 20mm graded crushed stone aggregate) slab supported on wall,beams and coloums in floor, roof, landing , deck slab and in shelves and the like etc complete all as specified and directed by Engr-in-Charge.

Hard core of broken stones or boulders of gauge in exc 63mm deposited spread and levelled in layers n. exc 15cm thick incl watering and rolled to true surface.

M&L 75mm thick cement concrete (1:4:8) type D2 using 40mm graded aggregate as in sub base to floor as specified.

M&L Non skid Ceramic coloured tiles 7 to 8mm thick area of each tiles exc 0.06 sqm but not exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm screed bed in CM 1:6 finished even and smooth for receive tiles complete all as specified.

M&L for Glazed ceramic coloured tiles in vertical surfaces 350x450x7mm thick etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade of tile over 10mm thick rendering in cement mortar 1:4 in backing coat of plaster for skrting/dado complete all as specified.

M&L for 20mm thick granite (of any type) work table rubbed and polished) in steps, pillars, jambs, window cills, cooking plateform/whash basin plateform etc and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified

M&L preparation of new or previously untreated surfaces on steel of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparationof new plastered surfaces on walls and applying two coats of cement based paint over a coat of primer.

S&F 15mm dia chromium plated fancy type Bib tap with round handle screwed down screwed for iron pipe or brass ferrule complete all as specified

S&F 110mm PVC (SWR) 'P' trap complete all as specified

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and as directed

S&F 110mm bore PVC (SWR) bends any radious with access door complete all as specified and as directed

PVC (SWR) pipes110mm dia single socketed in any length with rubber ring joints, laid in trenches or in floors

S&F for 16mm outer dia 3-layer PPR polypropylene random copolymer concealed pipes SDR 7.4 (PN16) UV stablized and antimivrobial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall, ceiling or in floors all as specified

S&F Gun metal globe or gate valve with iron wheel head screwed both ends for iron ipe and fixed of 20mm bore diacomplete all as specified and as directed

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm

Note : Deduction for amount of Rs 37280.00 as listed in Schedule A Part - II ( Schedule of Credit) shall be made while awarding of contract.

M/S BHAT ENGINEERS

M/S JAMSHEED ALI CONSTRUCTIONS