Providing Lift Water Supply Scheme to Village Makroli Chatter Bheri Dhiala Gadrana and Dini in Tehsil Indora Distt Kangra HP

Amount

Excavation in foundation in trenches in earth work in pick work, jumper work within all leads and lifts stacking the excavated soil not more than 3 mtr clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth sides of foundation etc., consolidating each deposited layer by ramming watering and then disposing of all surplus excavated earth as directed within all leads and lifts as per direction of Engineer-in- Charge.

Providing, laying cement concrete 1:6:12(1cement :6 sand:12 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work in foundation and plinth within all leads and lifts as per direction of Engineer-in-charge.

Squared rubble masonery coursed with hard stone of approved quality in foundation and plinth including raking out joints in cement mortar 1 : 6 ( 1 cement : 6 sand) within all leads and lifts as per the direction of Engineer -in- Charge.

Providing and laying damp proof course 38 mm thick with cement concrete 1:2:4 (1 cement:2 sand:4 graded stone aggregate 20mm nominal size) and curing complete within all leads and lifts as per the direction of Engineer -in- Charge.

Applying a coat of hot bitumen (mexphalt 80/100 or equivalent) using 1.70 kg. per square metre on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil within all leads and lifts as per the direction of Engineer -in- Charge.

Brick work using common burnt clay building bricks of approved quality in super structure in cement mortar 1:6 (1cement:6sand) above plinth level upto floor two level (2nd. class bricks) within all leads and lifts as per direction of Engineer-in-charge.

Brick work using common burnt clay building bricks of approved quality in foundation and plinth in cement mortar 1: 6 ( 1 cement : 6 sand ) 2nd class bricks within all leads and lifts as per the direction of Engineer-in -Charges.

Providing wood work in frames of doors, windows, clerestory, windows and other frames wrought,framed and fixed in position 2nd. Class deodar wood within all leads and lifts as per the direction of Engineer-in -Charge.

Providing and fixing panelled and glazed or panelled and glazed shutters for doors, windows and clerestory windows including bright finished / black enamelled iron butt hinges with necessary screws in 2nd. class deodar wood 40mm thick within all leads and lifts as per the direction of Engineer-in -Charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws within all leads and lifts as per the direction of Engineer-in -Charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering, strutting and propping etc., with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtr and removal of the same for insitu-reinforced concrete & plain concrete work in:

Foundation, footings basis of columns etc. and mass concrete within all leads and lifts as per direction of Engineer-in-charge.

Columns, pillars posts and struts circular or curved in plain upto any floor two level within all leads and lifts within all leads and lifts as per direction of Engineer-in-charge.

Beam, cantilever, girders and lintles side and soffits of beams, beam haunching, cantilevers, bressumers and lintles not exceeding one metre in depth in all height within all leads and lifts as per the direction of Engineer -in- Charges.

Flat surface such as soffits of suspended floors, roofs, landing and the like floor etc. up to 200 milimetres in thickness including all leads and lifts as per the direction of Engineer -in- Charge.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses, plinth and string courses and the like within all leads and lifts as per the direction of Engineer-in Charge.

Edges of slabs and breaks in floors and walls:under 20cm wide within all leads and lifts as per the direction of Engineer -in- Charges.

Stair cases with sloping or steped soffits excluding landing within all leads and lifts within all leads and lifts as per direction of Engineer-in-charge.

Providing form work of ordinary timber plankings so as to give a rough finish including centering, shuttering, strutting and propping etc. height of propping and centring below supporting floor to ceililing not exceeding 4 metres and removal of the same for insitureinforced concrete and plain concrete work in;-

Arches exceeding 6.00 metres spain within all leads and lifts as per direction of Engineer-in-charge.

Providing and laying cement concrete 1:2:4(1cement: 2sand: 4graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in

Columns,pillars posts and struts upto any floor two level within all leads and lifts as per direction of Engineer-in-charge.

Suspended floors, roofs, landing and shelves and their supports balconies, beams, girders and cantilever upto floor two level complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing Chequrred Precast terrazzo tiles hydraulic compressed 20 mm thick (with marble chips of specified sizes) fixed on wall on 10 mm thick cement plaster 1:3 (1 cement:3 sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing complete with tiles of following shades:- Silver Gray Shade within all leads and lifts as per the direction of Engineer -in- Charge.

20mm thick cement plaster in single coat on fair side of brick/stone masonry walls & interior plastering upto floor two level including internal angle chamfers &/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:4 (1cement: 4sand) complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

6mm cement plaster to ceiling in cement mortar 1 : 3 ( 1cement : 3 sand) within all leads and lifts as per the direction of Engineer-in -Charge.

15mm thick cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement:6sand) complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

Rough side exterior cement plaster on wall upto a height of 10meters above ground level with a mixture of sand and gravel or crushed stone graded from 6mm to 12mm nominal size dashed over and including fresh plaster in two coats,backing coat 10mm cement plaster 1:3(1 cement:3 sand) and inishing coat 10mm cement plaster with cement mortar 1:3(1 cement:3 sand )mixed with 10% finely grounded hyderated lime by volume of cement including arriss,chamfers and/or rounded angles not exceeding 80mm in girth complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

Providing plinth protection 50mm thick cement concrete 1: 3 : 6(1cement : 3 sand : 6graded stone agg., 20mm nominal size) including finishing the top surface concrete smooth within all leads and lifts as per direction of Engineer-in-charge.

Providing tor steel reinforcement for RCC. work including bending,binding and placing in position complete upto any floor two level within all leads and lifts as per the direction of Engineer-in- Charge.

Applying two coats of wood preservative on new wood and wood preservative on new wood and wood preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter,sand papering and knotting.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting ready mixed paint brushing wood primer pink within all leads and lifts as per the direction of Engineer-in-Charge.

Painting two coats( excluding priming coat) over new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of all dirt, dust and other foregin matter sand papering and stoping with enamel paint other than white within all leads and lifts as per the direction of Engineer-in-Charge.

White washing with lime on underocated surfaces (two coats) to give an even shade including thoroughly bromming the surface to remove all dirt, dust mortar dirt and other foreign matter within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing M.S. fan clamp type-I 16mm. Dia M.S. bar bent to shape with hooked ends in RCC slab during laying including painting the exposed portion of loop all as per standard design within all leads and lifts as per the direction of Engineer-in-Charge.

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size) within all leads and lifts as per the direction of Engineer -in- Charges.

Providing and fixing M. S sliding door bolts anodized tranparent obright finished or/and black enamelled with bolts and nuts screw etc., (250x16mm) complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing M.S. Tower bolts (barrel type) with screws (200x10mm) complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing M.S. Tower bolts (barrel type) with screws (150x10mm) complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing M.S. handles with necessary screws complete 100 mm complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing M.S. round or square bars (16mm) at required spacings in wooden frames of windows and clerestory windows within all leads and lifts as per direction of Engineer-in-charge.

Providing and laying cement concrete 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work form work in foundation and plinth within all leads and lifts as per the direction of Engineer-in-Charges.

Providing and laying cement concrete 1 : 1½ : 3 (1 cement : 1½ sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:-

Foundation, footing bases of column and the like mass concrete within all leads and lifts as per direction of Engineer-in-Charges.

Columns, pillars posts and struts upto any floor two level within all leads and lifts as per the direction of Engineer-in- Charge.

Lintle, beams, girders, brassumers and cantilevers upto any floor two level etc. within all leads and lifts as per the direction of Engineer-in- Charge.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto any floor two level within all leads and lifts as per direction of Engineer-in-Charges.

Suspended floor roofs, landing & shelves and their support balconies,beams, girders, bressumers cantilever up to floor two level including within all leads and lifts as per the direction of Engineer-in-Charges.

Arches (Tank bottm & top dome) upto any spain floor two level within all leads and lifts as per the direction of Engineer-in- Charge.

Wall (any thickness but not exceeding 0.10metre thickness) including attached pillasters buttersses, plinth and string concrete etc. from top of foundation level upto any floor two level within all leads and lifts as per the direction of Engineer-in- Charge.

Providing smooth finishing with cement mortar 1:3 (1 Cement :3 Sand) within all leads and lifts as per the direction of Engineer-in Charge.

Providing and fixing cast iron man hole cover 500mm internal diametres including frame weight 116 Kgs. (the weight of frame 58 Kgs and cover 58 Kgs) within all leads and lifts as per direction of Engineer-in-Charges.

Steel work welded in built-up section,trusses and framed work including cutting housting, fixing in position and applying a primering coat of red lead paint in gratings, framed guard bar, ladders, railngs, brackets, including locking arrangement and similars work within all leads and lifts as per direction of Engineer-in-charge.

Laying, jointing and testing galvanised mild steel tubes ( Medium grade) welded with M.S. flange table-5 including cost of nuts, bolts ferrado make gasket sheet 3mm thick. Flanges to be welded with single layer on inner side and double layer on outer side as per BIS:816-1965 latest with up to date amendsments. The flange provide every pipe within all leads and lifts as per the direction of Engineer-in -Charge for in Inlet, Outlet, over flow, Scour and by pass arrangement including connection of tank of following dia .

65 mm dia

80 mm dia

Manufacture and fixing of bend galvanised mild steel tubes ( Medium grade) difrent degree welded with M.S. flange table-5 including cost of nuts, bolts ferrado make gasket sheet 3mm thick. Flanges to be welded with double layer on inner side and single layer on outer side as per BIS:816-1965 latest with up to date amendsments of for in Inlet, Outlet, over flow, Scour and by pass arrangement including connection of tank of following dia within all leads and lifts as per the direction of Engineer-in -Charge.

65 mm dia

80 mm dia

Providing and fixing cast iron Sluice Valves Kartar Make for water works purpose PN 1.00 variety: PD,( with hand wheel) complete as per IS : 780-1984 class of following diametre including brass spindle and as per IS : 2906 class-II with M.S. flange, nuts, bolts, rubber insertion etc. for in Inlet, Outlet, over flow, Scour and by pass arrangement including connection of tank within all leads and lifts as per the direction of Engineer-in- Charge. class PN1.0 confirming to BIS-14846-2000 latest with upto date ammendments)

80 mm.nominal bore

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surface(two coat ) to give an even shade after throughly brushing the surface to remove all dirt and remains of loose powered materials within all leads and lifts as per the direction of Engineer -in- Charges.

Providing and fixing of M.S.Mosquito proofing ventilators 300mmx300mmx300mm complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing of M.S.Water Indicator gauge within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing of lightening conductors complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete With readymixed priming paint brushing red lead, red oxide/zinc oxide chrome at pipes, flanges, Railings ,Steel ladder within all leads and lifts as per direction of Engineer-in-charge.

Painting two coats(exclluding priming coat on new steel other metal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matters:-With enamel paint other than white at pipes, flanges, Railings ,Steel ladder within all leads and lifts as per direction of Engineer-in-charge.

Providing / Supplying for Structural Design and drawings complete in all respect.

Providing for Soil Bearing capacity test report from Govt. recognised firm complete in all respect.

Stone / boulder filling under floor and construction of approch road (including proper placing of boulder) complete in all respect within all leads and lifts as per the direction of Engineer-in -Charge.

Hirmachi colour wash on undecorated wall surfaces (Two coats) to give an even shade including thoroughly brooming the surface to remove all dirt, dust, mortar drops and other foreign matter within all leads and lifts as per the direction of Engineer-in-Charge.

Providing and fixing of fencing pannel of size 1.20mx1.80m of Jali 25X25mm welded to M.S.black tube of 32mm dia of 14 guage mm thick with M.S Flats 20X3mm, welded all around the pipe pannel two on both sides and providing hold fasts 7 Nos. of M.S. Flate of 32x3mm thickness having consting of tee of size 15X15 cms tee acting as hold fasts including cutting, weldign painting with red oxide paint to the entire satisfaction of the Engineer In charge

Laying, jointing and testing in trenches to be levelled to grade, BIS marked GI flanged pipes confirming to BIS:1239 (latest with upto date ammendments) of 65mm dia (Medium class) duly flanged after 5th pipe with intermediate butt welded joints including the cost of flanges, bends/short pieces made from parent tubes of diferent degrees cutting welding and jointing with flanges conforming to tables as specified below of BIS: 6392 (latest with upto date ammendments) welded at both ends as per BIS:816 (latest with upto date ammendments) with electrodes confirming to BIS 814 (latest with upto date ammendments) & provided with nuts and bolts BIS: 1369 (latest with upto date ammendments) of required sizes 4 mm thick champion make compressed asbestos fiber gasket or synthetic rubber gasket confirming to BIS:2712 (latest with upto date ammendments) & approved specifications as per site conditions including flushing, cleaning & hydraulic testing complete to the best satisfaction of Engineer-in-charge.

125 mm Dia ( Medium Class) dully flanged Table -5

100 mm Dia ( Medium Class) dully flanged Table -28

100 mm Dia ( Medium Class) dully flanged Table -17

100 mm Dia ( Medium Class) dully flanged Table -5

65 mm Dia ( Medium Class) dully flanged Table -28

65 mm Dia ( Medium Class) dully flanged Table -17

65 mm Dia ( Medium Class) dully flanged Table -5

Stage-Ist (Submersible Pumping Machinery Makroli Chatter ) Supply of submersible pumping set of Kirloskar/Kilburn/Clama/Crompton/KSB/BS make conforming to BIS; 8034-1976 latest suitable for lifting Raw water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacurer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:-2 Set of 10HP (2x10HP=20HP)

Total Head 36.77 mtrs

Discharge required from each pump. 7.65 LPS

No. of pump required 2 Nos .One act as stand by

Location of the site of installation of machinery. The site is located at a distance of 5 km from Nurpur Road Railway station

The Altitude of installation. The altitude of place is 500 mtr above MSL

Type of current. AC three phase supply with 50 cycles per second

Rate Voltage 415 +10%

Type of water and its source Tubewell

Charactristics of water.

a)Ambient Temperature dig.c 20 dig.C

b)Turbidity NTU up to 10 NTU

c)Hardness260Mg/Ltrs(as CaCO3) Mg/Ltr as (caco3)

f)Other

Depth ofTube Well

LWL in Tube Well

Center line level of Pump 72.00 mtr

Discharge level of highest point 72.00 mtr

Static head in Mrs 32.00 mtrs

Length of R/Main 200 mtr

Dia of Rising main 125 mm dia GI pipe (MC)

No of working hours per day 8 hrs

Limit of pump operation. (-) 15% (+) 10% of total head

R.P.M. of pumping set. 2900 RPM

Test run. 8 hrs continueousely for 7 days

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for centrifugal pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 2 nos. pump of rating 10 HP automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Make: Aarmation Electric Private Limited/ MAS/ELLES

Variable frequency drive starter of 10 HP Heavy Duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It Should be capable to control the frequecy of pumps through out the operation and also should be capable to maintain the power factor of the system within acceptable limits. It should have ambient temperature 50 Degree without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. Make: Aarmation Electric Private Limited/MAS/ELLES

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc with RS 485 communication Make L&T/Conserve/Siemens

MCB /MCCB suitable capacity of L&T / Standard make on the coming feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) with neutral linked under voltage release.

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments.

Incommer MCCB with for proper short circuit capability for both the starters make L&T/Schnieder/ABB

On / Off indicator and push button, Control and power wiring,Power capacitor,Cooling fan 230 VAC, Contorl terminal, Buss Bar, i.e.Bolt, insulator, etc.

Input Choke which should be installed at the input of VFD starter, so that there should be proper protection in case of any voltage surge and distortions in signal

Control Transformer to safegaurd the control circuit of all the components from the voltage surges and spikes.

Output contactors in the output of VFD to run the pump

Transporatation and Carrage Charges for panel till site

Programmable logic controller with appropriate digital and analog inputs and outputs to give automatic command to star delta and also will get data from Multi function Meter for Current, Voltage, KWH, PF and THD. Make Mitsubishi/L&T/Delta

HMI 7" display with IOT to give on and off command manually and also to show pump running and breakdown status at pump station Make Wientek/Exor/Mitsubishi/Mecon.

Supply of software with license to monitor data at Laptop/Mobile in form of Software and Mobile Application for 3 users

Level Sensor to indicate the water level of tank remotely

Cloud GateWay for Data Cluding to Server

Cable for Communication for Water Level Sensor

Installation and Commissioning

Supply of Kirloskar/ Kilburn/Leader make Cast iron double flanged accuator swing check type reflux valve class PN 1.0 having bye pass arrangement ( to be provided on delivery side) of size of one size higher than the delivery size of pump and shall be suitable for withstanding nominal seat presure of 10.20 Kg/Cm2 as per BIS 5312-1984 Part-I

Supply of Kirloskar/ Kilburn/Leader make Cast iron class PN 1.0 double flanged acctuator swing check type reflux valve having bypass arrangement equal to dia of Risng main i.e. 125mm shall be suitable for withstanding nominal seat pressure of 10.20 Kg/Cm2 as per BIS 5312-1984 ( Latest edition)

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.

On supply side of 3½ core coper cable 6.00 mm^2 ( From HPSEB Meter to Switch & Starter).

On motor side 3 core flat joint less copper cable of size 4.00 mm^2 ( From Switch & Starter to Motor) pump installed in the bore.

Supply & errection of floor/wall mounted power shunt capacitor conforming to BIS 2834-1986 latest with upto date ammendments of GEC/Siemen/ Havells L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually of requirement KVAR according to 100 BHP of motor offered including cable Siemens/Gloster/ICC make from busbar chamber to capacitor & also including Standard/ L&T/Kilburn/Indo asian make ICTP switches conforming to BIS 4064- 4064-1978 or latest with HRC fuses. (range to be specified by the tenderer). 2x4KVAR or Set

Supply of standarad make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

P/L G.I. pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of (Actual laying to be done as per Final drawings to be approved by the Engineer-in-Charge.

Suction Pipe 100 mm dia

Delivery pipe --- mm dia

Errection of all equipments including cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

Stage-IInd (Phase- Ist) Supply of horizontal spindle,horizontal/radial split casing and suction (backpull out arrangement) single/ double / multistage centrifugal pumps or combination of pumps in series /parallel of KSB/Mather & Platt/Jyoti/Kirloskar/BE/Maxflow/Beaconweir/Sabar make conforming to BIS: 1520-1980 (latestwith upto date ammendments) read with BIS: 9137-1978 (latest edition) suitable for lifting water of under mentioned charactristics with impellers of bronze/suitable alloy, priming funnels,casing ring & shaft sleeves of bronze/ suitable alloy, shaft of sutable steel grade with cast iron casing coupled directly through a flexible coupling on a common C.I. / Cast steel base plate (base plate to be from the principle manufacturer of pumping set) to slippering/squirrel cage screen protected drip proof electric induction motor of Kirlokar /NGEF/Crompton / Siemen /Jyoti /BHEL /GEC( Marrathon) /ABB conforming to BIS: 325-1978 read read with BIS: 900-1968 (latest with upto date ammendments) It should include the cost of bearings, nuts & bolts,painting etc. and shall be suitable for operation as per data given below. 2 Set of 25 HP

Total Head 164.80 MTRS

Discharge required from each pump. 5.46 LPS of each pump

No. of pump required 2 set (one will act as stand by)

Location of the site of installation of machinery The site located at a distance of 5 km from Nurpur Road railway station and point 200 km on head load (for installtion of both machineries)

The altitude of installation. 500 MSL

Type of current. AC three phase supply with requency of 50 cycles per second

Rate Voltage 415 +10%

Type of water and its source Tubewell

Shaft level

Level of discharge point 221.70

Static Head 121.70

Charactristics of water.

a)Ambient Temperature dig.c 20 degree

b)Turbidity NTU up to 10 NTU

c)Hardness260Mg/Ltrs(as CaCO3) Mg/ Ltr as (caco3)

f)Other

Depth of well assembly

No. of working hours per day

Length of Rising main 3560 mtr

Dia of Rising main 100 mm G.I. (MC)

Limit of pump operation. In the completion range of (-) 75%

R.P.M. of pumping set. 2900 RPM

Test run. 8 hrs continueousely for 7 days

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for centrifugal pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 2 nos. pump of rating 25 HP automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Make: Aarmation Electric Private Limited/MAS/ELLES

Variable frequency drive starter of 25 HP Heavy Duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It Should be capable to control the frequecy of pumps through out the operation and also should be capable to maintain the power factor of the system within acceptable limits. It should have ambient temperature 50 Degree without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. Make: Aarmation Electric Private Limited/MAS/ELLES

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc with RS 485 communication Make L&T/Conserve/Siemens

MCB /MCCB suitable capacity of L&T / Standard make on the coming feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) with neutral linked under voltage release.

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments.

Incommer MCCB with for proper short circuit capability for both the starters make L&T/Schnieder/ABB

On / Off indicator and push button, Control and power wiring,Power capacitor,Cooling fan 230 VAC, Contorl terminal, Buss Bar, i.e.Bolt, insulator, etc.

Input Choke which should be installed at the input of VFD starter, so that there should be proper protection in case of any voltage surge and distortions in signal

Control Transformer to safegaurd the control circuit of all the components from the voltage surges and spikes.

Output contactors in the output of VFD to run the pump

Transporatation and Carrage Charges for panel till site

Programmable logic controller with appropriate digital and analog inputs and outputs to give automatic command to star delta and also will get data from Multi function Meter for Current, Voltage, KWH, PF and THD. Make Mitsubishi/L&T/Delta

HMI 7" display with IOT to give on and off command manually and also to show pump running and breakdown status at pump station Make Wientek/Exor/Mitsubishi/Mecon.

Supply of software with license to monitor data at Laptop/Mobile in form of Software and Mobile Application for 3 users

Level Sensor to indicate the water level of tank remotely

Cloud GateWay for Data Cluding to Server

Cable for Communication for Water Level Sensor

Installation and Commissioning

Supply of Kirloskar/ Kilburn/Leader make Cast Steel actualated sluice valve class ASA-150 conforming to BIS-1414 API-600 having size one dia higher than the delivery size of pump and shall be suitable for withstanding nominal seat presure of 21 Kg/Cm2 as per BS-1868/API-600) complete in all respect

Supply of Kirloskar/ Leader make Cast steel double flanged swing check type reflux valve having bypass arrangement of class ASA-150 confirming to BS 1868/API-600) ( latest edition) to be provided on Rising main) of size i.e. 100mm dia and shall be suitable for withstanding nominal seat pressure of 21 Kg/cm2 (100mm dia)

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.

On supply side of 3½ core coper cable 10mm^2 ( From HPSEB Meter to Switch & Starter).

On motor side 3 core flat joint less copper cable of size 6 mm^2 ( From Switch & Starter to Motor) pump installed in the bore.

Supply & errection of floor/wall mounted power shunt capacitor conforming to BIS 2834-1986 latest with upto date ammendments of GEC/Siemen/ Havells L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually of requirement KVAR according to 25 BHP of motor offered including cable Siemens/Gloster/ICC make from busbar chamber to capacitor & also including Standard/ L&T/Kilburn/Indo asian make ICTP switches conforming to BIS 4064- 4064-1978 or latest with HRC fuses. (range to be specified by the tenderer). 2x6=12KVAR or set

Supply of standarad make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

Providing and Laying G.I. pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of (Actual laying to be done as per final drawings to be approved by the Engineer-in-charge)

Suction Pipe --- mm dia

Delivery pipe --- mm dia

Common header = 100 mm dia

Providing and lying double loop earthing with coper plate 600x600 x3 thick electrode and copper strip of 25x3 complete including providing of material such as charcoal, common salt, GI pipes, thimbles, nuts & bolts, digging of pits, Copper /GI wire/ Strips of required capacity conforming to BIS 8034-1978 latest with upto date ammendments for above motor & other electriacl equipments including all civil works. (for both machineries)

Errection of all equipments including cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

Stage -IInd (Phase-IInd) Supply of submersible pumping set of Kirloskar/Kilburn/ Clama/Crompton/ KSB/BS make conforming to BIS; 8034-1976 latest suitable for lifting Raw water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacurer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:-2 Set of 10HP =20HP

Total Head 153.58 mtrs

Discharge required from each pump. 2.22 LPS of each pump

No. of pump required 2 set (one will act as stand by)

Location of the site of installation of machinery The site located at a distance of 5 km from Nurpur Road railway station and point 200 km on head load (for installtion of both machineries)

The Altitude of installation. The altitude of place is 500 mtr above MSL

Type of current. AC three phase supply with requency of 50 cycles per second

Rate Voltage 415 +10%

Type of water and its source Tubewell

Shaft level

Level of discharge point 205.90 mtr

Static Head 105.90 mtr.

Charactristics of water.

a)Ambient Temperature dig.c 20 degree

b)Turbidity NTU up to 10 NTU

c)Hardness260Mg/Ltrs(as CaCO3) Mg/ Ltr as (caco3)

f)Other

Depth of Sump Well

LWL in Sump Well

Center line level of Pump

Discharge level of highest point 205.00 mtr

Static head in Mrs - mtrs

Length of Rising main 2570 mtr

Dia of Rising main 65mm dia G.I. (M)

No. of working hours per day 8 hrs

Limit of pump operation. In the completion range of (-) 75%

R.P.M. of pumping set. 2900 RPM

Test run. 8 hrs continueousely for 7 days

Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for centrifugal pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 2 nos. pump of rating 10 HP automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Make: Aarmation Electric Private Limited/MAS/ELLES

Variable frequency drive starter of 10 HP Heavy Duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It Should be capable to control the frequecy of pumps through out the operation and also should be capable to maintain the power factor of the system within acceptable limits. It should have ambient temperature 50 Degree without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. Make: Aarmation Electric Private Limited/MAS/ELLES

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc with RS 485 communication Make L&T/Conserve/Siemens

MCB /MCCB suitable capacity of L&T / Standard make on the coming feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) with neutral linked under voltage release.

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments.

Incommer MCCB with for proper short circuit capability for both the starters make L&T/Schnieder/ABB

On / Off indicator and push button, Control and power wiring,Power capacitor,Cooling fan 230 VAC, Contorl terminal, Buss Bar, i.e.Bolt, insulator, etc.

Input Choke which should be installed at the input of VFD starter, so that there should be proper protection in case of any voltage surge and distortions in signal

Control Transformer to safegaurd the control circuit of all the components from the voltage surges and spikes.

Output contactors in the output of VFD to run the pump

Transporatation and Carrage Charges for panel till site

Programmable logic controller with appropriate digital and analog inputs and outputs to give automatic command to star delta and also will get data from Multi function Meter for Current, Voltage, KWH, PF and THD. Make Mitsubishi/L&T/Delta

HMI 7" display with IOT to give on and off command manually and also to show pump running and breakdown status at pump station Make Wientek/Exor/Mitsubishi/Mecon.

Supply of software with license to monitor data at Laptop/Mobile in form of Software and Mobile Application for 3 users

Level Sensor to indicate the water level of tank remotely

Cloud GateWay for Data Cluding to Server

Cable for Communication for Water Level Sensor

Installation and Commissioning

Supply of fixing of doble flanged acctuator cast iron sluice valve heavy size one dia higher tha pump size to delivery of pump class PN 1.6 of Kirloskar/Kilburn/Leader make conforming to BIS 14846-2000 laest with up to date ammendments having seat pressure of 16.32kg/cm2 complete in all respect.

Supply of Kirloskar/ Kilburn/Leader make Cast iron double flanged swing check type reflux valve class PN 1.6 having bye pass arrangement ( to be provided on delivery side) of size of one size higher than the delivery size of pump and shall be suitable for withstanding nominal seat presure of 16.32 Kg/Cm2 as per BIS 5312-1984 Part-I

Supply of Kirloskar/ Kilburn/Leader make Cast iron class PN 1.6 double flanged swing check type reflux valve having bypass arrangement equal to dia of Risng main i.e. 65mm shall be suitable for withstanding nominal seat pressure of 16.32 Kg/Cm2 as per BIS 5312-1984 ( Latest edition)

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.

On supply side of 3½ core coper cable 6.00 mm^2 ( From HPSEB Meter to Switch & Starter).

On motor side 3 core flat joint less copper cable of size 4.00 mm^2 ( From Switch & Starter to Motor) pump installed in the bore.

Supply & errection of floor/wall mounted power shunt capacitor conforming to BIS 2834-1986 latest with upto date ammendments of GEC/Siemen/ Havells L&T make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually of requirement KVAR according to 100 BHP of motor offered including cable Siemens/Gloster/ICC make from busbar chamber to capacitor & also including Standard/ L&T/Kilburn/Indo asian make ICTP switches conforming to BIS 4064- 4064-1978 or latest with HRC fuses. (range to be specified by the tenderer).2x4=8KVAR or set

Supply of standarad make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.

Providing /Laying G.I./MSERW pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of (Actual laying to be done as per final drawing to be approved by teh Engineer-in-charge

Suction Pipe 50 mm dia

Delivery pipe __ mm dia

Common header = 65 mm dia

Providing and lying double loop earthing with coper plate 600x600 x3 thick electrode and copper strip of 25x3 complete including providing of material such as charcoal, common salt, GI pipes, thimbles, nuts & bolts, digging of pits, Copper /GI wire/ Strips of required capacity conforming to BIS 8034-1978 latest with upto date ammendments for above motor & other electriacl equipments including all civil works. (for both machineries)

Errection of all equipments including cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.

HYDRO ENGINEERING COMPANY

sadeep kumar

Sarbjit Singh Katoch