REPAIR/MAINT OF JOINERY, PLUMBING AND SANITARY FITTING/FIXTURES, ROOF SHEET, CEILING, FLOORING ETC TO OTM ACCN AT ZONE B AREA AND REPAIR/REPLACEMENT OF STREET LIGHTS, STREET LIGHT POLES, EARTHINGS WITH CONNECTED ELECTRICAL WORKS AT KANCHRAPARA UNDER

Amount

PART-I Taking down cement plaster of any description on brick or stone or concrete surface of wall etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlars facing dressed stonework & precast concrete articles complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specially provided for complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description etc complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi-corrugated etc.) sheets in roof coverings complete all as specified and directed.

Dismantling timber scantlings (framed work) 40 sq.cm and over in section, in any position complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Taking down chowkats or frame (without taking off shutter from the frames) exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and directed.

Taking down chowkats or frame (without taking off shutter from the frames) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down of shutter of any description exceeding 1 Sqm but not exceeding 2.0 Sqm each complete all as specified and directed.

Taking down of shutter of any description not exceeding 1 Sqm each complete all as specified and directed.

Taking down of shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each and refixing in same opening after easing and adjusting completed all as specified and directed.

Taking down of shutters of any description not exceeding 1 sqm and refixing in same opening after easing and adjusting completed all as specified and directed.

Resecuring or easing & adjusting without taking down of shutters of any description exceeding 1 sqm and not exceeding 2 Sqm each complete all as specified and as directed

M&L for PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 (using 20 mm graded stone aggregate) used as in brick, concrete wall for fixing of hold fast and like etc including necessary form work complete all as specified and directed.

M&L for RCC (nominal mix) (1:2:4) type B1 (using 20mm graded crushed stone aggregate) used as in slab supported on walls, beams and columns in floors, roofs, landing, balconies, canopies, deck slabs and in shelves and like etc complete all as specified and directed.

M&L for cutting chases, in brick wall, pinning in and making good to facing where required and pointing in cement mortar (1:3), to ends or edges of landing, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing etc and making good the disturbed surface, cutting not exceeding 10cm girth complete all as specified and directed.

M&L for brick work with sub class 'B' bricks locally available best quality straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks locally available best quality , straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

Supply only integral water proofing compound liquid, ISI marked complete all as specified and directed.

Providing formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs exceeding 5 cm but not exceeding 10 cm wide for rough finished surfaces of concrete, flat complete all as specified and directed.

Providing formwork to the soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200 mm thick (horizontal or sloping ) and making flat, rough finished surfaces of concrete complete all as specified and directed

S&F of second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints etc complete all as specified and directed.

S&F of second class hard wood in scantling, clean swan as in frame work, fixed with nails complete all as specified and directed.

S&F of 35mm thick (factory made) second class hard wood glazed/ gauge & skeleton shutters for door & windows, open rebated & prepared to receive glass, gauge etc. (without sash bars) edges of framing divided into square with plain, chamfered or rounded, fitted with cut & mitered rebated sash bars, any numbers for securing glass etc. sizes of members of shutters as specified in SSR Part-I, Section-8, Clause 8.24 (a) (larger size to be provided) complete all as specified and directed.

S&F of 35mm thick (factory made) second class hard wood glazed/ gauge & skeleton shutters for door & windows, open rebated & prepared to receive glass, gauge etc. (with sash bars) edges of framing divided into square with plain, chamfered or rounded, fitted with cut & mitered rebated sash bars, any numbers for securing glass etc. sizes of members of shutters as specified in SSR Part-I, Section-8, Clause 8.24 (a) (larger size to be provided) complete all as specified and directed.

S&F of 30 mm thick flush door shutters (factory made) solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

S&F of factory made solid PVC door frame of size 50mm X 47mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube as per specification and drawing as mentioned in SSR Part-II (2020), Section 8, Page No. 178 complete all as specified and directed.

S&F of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification & drawing as mentioned in SSR Part-II (2020), Section 8, Page No.174 complete all as specified and directed.

S&F in repair of 18-19 mm thick veneered particle board fixed in cupboard shelves interior grade, solid core, medium density general purposes type with commercial face veneers type 'BB' complete all as specified and directed.

S&F in repairs of double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel (heavy duty) complete all as specified and directed.

S&F of 250 mm long mild steel, sliding door bolt, plate type, stove enamlled black, with bright bolt not less than 12mm dia with and including a minimum of six numbers bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F in repairs of 250 mm long mild steel, sliding door bolt, plate type, stove enamlled black, with bright bolt not less than 12mm dia with and including a minimum of six numbers bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F of 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F of 200mm long mild steel barrel tower bolts, stove enamelled black with bright bolt and fixed complete all as specified and directed.

S&F in repairs of 200mm long mild steel barrel tower bolts, stove enamelled black with bright bolt and fixed complete all as specified and directed.

S&F of 150mm long mild steel barrel tower bolts, stove enamelled black with bright bolt and fixed complete all as specified and directed.

S&F in repairs of 150mm long mild steel barrel tower bolts, stove enamelled black with bright bolt and fixed complete all as specified and directed.

S&F of 150mm long mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S&F for 100mm long mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S&F of 150 mm long aluminium anodised extruded alloy handle fabricated type complete all as specified and directed.

S&F of 100 mm long cold rolled mild steel butt hinges, medium weight complete all as specified and directed.

S&F for 75 mm long stainless steel butt hinges complete all as specified and directed.

S&F in repairs of 20mm dia harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed.

S&F of stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm & fixed with stainless steel wire staple complete all as specified and directed.

S&F in repairs of stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm & fixed with stainless steel wire staple complete all as specified and directed.

M&L for TMT bars 10 mm dia and over cut to length bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F of mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or forged into spikes; framed guard bars; barred iron doors; ladders, railings, framed brackets, walk ways, frame work of water tank and similar work conforming to Fe-290-0 Gde-E-165 complete all as specified and directed.

S&F of pressed steel frames (factory made) for door of size 125mm X 60mm of 1.25mm thick with one or more rebates including necessary fittings lugs, hinges, lock strike plate, etc including filling of concrete (1:3:6) type C-0 (using 12.50 mm graded crushed stone aggregate) including applying of two coats of black bituminous paint (shop coat) to back of chowkats complete all as specified and directed.

S&F of pressed steel frames for door (factory made) of size 105mm X 60mm of 1.25mm thick with one or more rebates including necessary fittings lugs, hinges, lock strike plate, etc including filling of concrete (1:3:6) type C-0 (using 12.50 mm graded aggregate)including applying of two coats of black bituminous paint (shop coat) to back of chowkats complete all as specified and directed.

S&F of steel windows with side hung shutters including box type hinges with steel handle, steel peg stay, complete with glazing bars, dovetailed or welded to receive wire mesh/glass after and including taking down old unserviceable steel window complete all as specified and directed.

S&F for steel windows with side hung shutters including box type hinges with steel handle, steel peg stay, complete without glazing bars , dovetailed or welded to receive wire mesh/glass complete all as specified and directed.

S&F of steel ventilators with top hung shutters including hinges, steel peg stay after and including taking down old unserviceable steel ventilators complete all as specified and directed.

S&F of anodized aluminium frame for window with one or more rebates and anodized aluminium window, sliding type shutters, sliding on three way aluminium channel, without sash bars, sliding on separate track, made out of aluminium section weighing 0.55 Kg/RM and necessary jointing cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, fittings such as suitable anodized aluminium locking type handle etc. with and including supply and fixing of 5mm thick sheet glass, tinted for two channels and stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm for one channel to make the window fly proof after and including taking down old unserviceable windows complete all as specified and directed.

S&F of anodized aluminium frame for door of size 65 X 38mm with anodized aluminium push/ pull glazed type shutter with lock rail , top rail and stiles of size 84 x 44mm and size 115 X 44 for bottom rails and necessary jointing cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium handles, with and including supply and fixing of 5.5mm thick sheet glass, tinted and minimum 3 Nos 100mm size aluminium hinges per shutter after and including taking down old unserviceable doors complete all as specified and directed.

S&F of pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old unserviceable sheet complete all as specified and directed.

S&F of pre-painted galvalume aluminium zinc coating GI based plain steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in ridge / wall/cladding, fixed with self tapping screws complete all as specified and directed.

S&F of false ceiling with exposed metal (PPGI) framework/ “Tee” Grid providing and fixing of suspended Tee grid false ceiling using “T” Grid System – powder coated GI (PPGI) exposed grid false ceiling suspension system in grid size 600mm x 600mm with main runner 32 x 24mm x 0.3mm thick, cross tee 26mm x 24mm x 0.3mm thick and wall angle 24mm x 24mm x 0.40mm thick using 4mm thick non asbestos fibre cement board of size 595 x 595mm, an asbestos Free fibre cement board manufacture using high Pressure System Curing technology. T grid Framing is suspended using 4mm GI/MS bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip, also providing provisions for light fixtures, air conditioning diffusers and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at not more that 300mm from the adjacent wall. 1220mm/600mm Cross Tee to be interlocked between main runners @ 600mm c/c, so as to from 600mm x 600mm or 1200mm x 600mm grid, confirming IS 14862 & type B category III of ISO 8336, tested as per AS 1530 part – 3 & B. S- 476 part 4,5,6,7 & 8 should be placed in Grid module to form complete all as specified and directed.

S&F of mild steel flat iron as in hold fast, wind tie including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F of 6mm thick non asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc. fixed with 'L' or 'J' type hooks complete all as specified and directed.

S&F of 6mm thick non asbestos cement two pieces adjustable serrated ridge for corrugated or semi- corrugated sheets fixed with 'L' or 'J' type hooks complete all as specified and directed.

S&F of 0.63 mm thick, galvanised, corrugated mild steel sheeting with two corrugated side lap fixed with 'L' type cranked bolt hooks as in vertical surface of hanger, wall, roof etc with grade of zinc coating 275 gm per sqm after and including dismantling of existing unserviceable sheet complete all as specified and directed.

S&F of 0.63 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip & straight flashing (legth & girth as fixed) with grade of zinc coating 275 gm per sqm after and including dismantling of existing unserviceable sheet complete all as specified and directed.

S&F for 4mm thick non asbestos cement plain building boards, fixed to timber framework with screws after and including dismantling existing unserviceable board complete all as specified and directed.

M&L for 20 mm thick 2nd class hardwood wooden boarding plained at one side with butt joints and fixed complete in position as in eaves board etc complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in plinth protection finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate), as in sub base of floor complete all as specified and directed.

M&L for 18-20 mm thick granite slab (of any type) machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the of granite stone including grinding and polishing over and including 15 mm thick screed bed of cement mortar (1:6) complete all as specified and directed.

M&L for 18-20mm thick granite (of any type) tiles machine cut, in wall/pillar/skirting/dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including a backing coat of 10mm thick plastering in cement mortar (1:4) complete all as specified and directed.

M&L for non skid (joint free) ceramic coloured tiles of 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match with shed of tiles over and including 15mm thick screed bed or beading layer of cement mortar (1:4) for laying floor finishes complete all as specified and directed.

Ditto-all as per Item No.74.00 here-in-before but in skirting/dado over and including a backing coat of 10mm thick cement plaster in cement mortar (1:3) complete all as specified and directed.

M&L for vitrified light shade (shade as approved) ceramic tiles (ultra charge) 10mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 Sqm in floors etc set over and including 15mm screed bed in cement mortar (1:6) and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M&L for glazed ceramic coloured wall tiles (vertical) of size 450mm X 300mm X 7mm thick or equivalent set and jointed neat cement slurry and pointed with white cement mixed with pigment to match with shed of tiles as in skirting/dado/vertical wall over and including 10 mm thick cement plaster in cement mortar (1:3) complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab flooring (pre-mirror polished) over and including 20mm thick screed bed of cement mortar (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 18-20mm thick machine cut kota stone slab in riser of steps, skirting, dado and pillar laid over and including 10mm cement plastering in cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 60mm thick machine pressed precast concrete interlocking paver block (coloured and polished) any shape and size with grey cement and pigment confirming to IS 15658-2008 (M-35 grade) laying over and including 50mm thick sand filling after and including dismantling old tile block complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on brick work or concrete surfaces of wall, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair face of brick works or concrete surfaces of walls with cement mortar (1:4) mixing with mixed with WPC @200ml per 50 Kg of cement or as per manufacturer's instructions , finished the surfaces even & smooth without using extra cement complete all as specified and directed. (Note : WPC will be measured and paid separately under relevant item)

M&L for rendering 10mm thick in CM (1:3) on concrete surfaces of ceiling, beams, lintels, chajjas etc in patches including preparation of exposed reinforcement surfaces, cleaning with rotary brush to remove all loose rust and treating with single component solution of rust remover and applying anti rust coating and finished the plaster surface even and smooth without using extra cement complete all as specified and directed.

M&L for applying three coats of white wash on wall surface including preparation of new plastered surface complete all as specified and directed.

M&L for applying two coats of oil emulsion distemper over a coat of alkaline resistant primer after preparation of newly plastered surfaces of ceiling complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer after preparation of new steel surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer after preparation of new wooden surfaces of any description over 10 cm girth or width complete all as specified and directed.

S&F of 3.0mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares not exceeding 0.50 sqm each pane complete all as specified and directed.

Hacking out old brorken glass (any thickness and size, quality or description from wooden frame etc) fixed with putty or beads complete all as specified and directed.

S&F in repairs of 15mm dia bib tap, fancy type, cast copper alloy with crutch or butterfly handles, screwed down, screwed for iron pipe or for brass ferule, chromium plated with long screw type fixed complete all as specified and directed.

S&F in repairs of 15 mm bore angular stop valve, fancy type, chromium plated, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs of 15 mm bore stop valve, fancy type chromium plated with long shank and cup (concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs of 15mm dia pillar tap, fancy tpype, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with letter 'HOT' or 'COLD' with long screwed shanks & fly nuts, screwed for iron pipes complete all as specified and directed.

S&F in repairs of brass chromium plated tubular towel rail, 20mm dia, D-type, 60cm long between flanges complete all as specified and directed.

S&F in repairs of 15 mm dia PVC connection pipe of length 600 mm with PTMT nuts complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F in repairs of 20mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipes or for unions pipes, fixed complete all as specified and directed.

S&F of 15mm dia tubes (medium grade) galvanised iron, with all fittings and fixed complete to walls and ceilings or laid in floors, wall etc (surface or concealed type) after and including taking up or down existing unserviceable steel tubing complete all as specified and directed.

S&F of 20mm dia tubes (medium grade) galvanised iron, with all fittings and fixed complete to walls and ceilings or laid in floors, wall etc (surface or concealed type) after and including taking up or down existing unserviceable steel tubing complete all as specified and directed.

S&F in repairs of 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe & fixed (minimum weight 210 gms) complete all as specified and directed.

S&F of 1000 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) multi layer (three layer), ISI Marked hoisted and fixed in position with cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection after and including dismantling / taking down old unserviceable PVC water tank, ball valve etc complete all as specified in SSR Part-I and directed.

S&F of 500 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) multi layer (three layer), ISI Marked hoisted and fixed in position with cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection after and including dismantling / taking down old unserviceable PVC water tank, ball valve etc all as specified in SSR Part-I complete all as specified and directed.

Disconnecting existing water tanks of (exceeding 500 & not exceeding 1000 litres in capacity), setting aside (or lowering if required) and cleaning, removing all scale and dirt etc from tanks and mouth of pipe including hoisting (if required) reconnecting and refixing in position with required fittings complete all as specified and directed. (NOTE: Date of cleaning must be written at side of water tank with white paints after cleaning of tank)

Disconnecting existing water tanks of (exceeding 250 & not exceeding 500 litres in capacity), setting aside (or lowering if required) and cleaning, removing all scale and dirt etc from tanks and mouth of pipe including hoisting (if required) reconnecting and refixing in position with required fittings complete all as specified and directed. (NOTE: Date of cleaning must be written at side of water tank with white paints after cleaning of tank)

S&F in repairs of PVC Cover/ Lid (ISI Marked) for PVC water tank of 250 Ltr to 1000Ltr capacity complete all as specified and directed.

S&F in repairs of vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern but including flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2) securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S&F in repairs of vitreous china wash basin, white, flat back, size 550 X 400 mm, excluding taps, chain and plug and porcelain stopper but including waste pipe, brackets and cutting for and pinning in ends of brackets or erecting stand acomplete all as specified and directed.

S&F in repairs of vitreous china wash down water closet pan (pedestal pattern) white with P or S trap (excluding flushing cistern & flush pipe) including connection to trap & to flushing pipe, anti-syphonage pipe & seat cover etc. including making good to floor complete all as specified and directed.

S&F in repairs of PVC water closet seat cover, white/black colour as required, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repairs of 10 Ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with all internal accessories and fixed to wall and jam nuts on both sides, PVC flush pipe 32mm dia suitable for low level cistern fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor complete all as specified and directed.

S&F in repairs of vitreous china squatting pan 'Orissa' pattern, size 580x440mm white, with integral foot rests with P or S trap (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe etc complete including making good to floors with PCC bedding (1:4:8) type D2 using 40mm nominal brick ballast and connection to trap with cement mortar, and making good to floor complete all as specified and directed.

S&F in repairs of 32mm dia, PVC waste pipe (flexible) for sink/WHB complete all as specified and directed.

S&F in repairs of overhead shower 125mm dia round shape , single flow (ABS body chrome plated with grey face plate) with rubit cleaning system complete all as specified and directed.

S&F in repairs of chromium plated hand shower (health faucet) with 8mm dia CP tube of 1.2 mtr long complete all as specified and directed.

S&F in repairs of sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F of stainless steel kitchen rack of size 750mmX600mmX250mm, 1mm thick, fabricated type with all fixings accessories complete all as specified and directed.

S&F in repairs of aluminium extuded body door closer hydraulically regulated designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg as fixed complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or laid in trenches or in floor including taking down old unserviceable pipe complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F of salt glazed stone ware gully trap of size 150mmX150mm square or round mouthed type including jointing to drain pipe in CM (1:1) complete all as specified and directed.

S&F in repairs of 50mm bore high density polyethylene pipes (HDPE) of pressure rating 6kgf/cm2 fixed complete to wall, ceiling or in floors etc. complete all as specified and directed.

S&F of 100mm dia CI branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

M&L for 100mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) including taking down old unserviceable CI floor trap complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:3) on ceiling, chajja etc surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying three coats of white wash on wall surface including preparation of new plastered surface complete all as specified and directed.

PART-II S&F of 36 watt LED street light fittings, 230 V, IP-65/66 pressure die cast housing LED lamp aluminium compact high power LED street light with heat resistant toughened glass with LED lamp and necessary electric connection with suitable size copper cable after and including taking down old unserviceable fittings complete all as specified and directed . (Make : Crompton Greaves Cat No LSTS-36-CDL-M/ Bajaj Cat No BRTFG 36W LED or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of 60 watt LED street light fittings, 230 V, IP-65/66 pressure die cast housing LED lamp aluminium compact high power LED street light with heat resistant toughened glass with LED lamp and necessary electric connection with suitable size copper cable after and including taking down old unserviceable fittings complete all as specified and directed . (Make : Crompton Greaves Cat No. LST-60-CDL-M/Bajaj Cat No. BRTFG 60W LED V3/Havells Cat No. ENDURAPEARLNEOSL60WLED757PASYTOPC or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of LED flood light fitting of capacity 70 Watt in aluminium PDC housing with LED lamp, toughened glass cover with IP66 protection with 4/5 KV inbuilt surge protector and cable connection from looping box to light fitting at any height and testing after and including taking down existing unserviceable light fittings complete all as specified and directed . (Make:-Crompton Greaves Cat No.CG-LFL-70-CDL/60-M /Havells Cat No.JETAPROFL70WLED757LTG or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of LED flood light fitting of capacity 120 Watt in aluminium PDC housing with LED lamp, toughened glass cover with IP66 protection with 4/5 KV inbuilt surge protector and cable connection from looping box to light fitting at any height and testing after and including taking down existing unserviceable fittings complete all as specified and directed . (Make:-Crompton Cat ref No.CG-TFS-504-120-57-60D-SL-GL-NSG /Havells cat No. JETAIRISFLS120WLED757APWBLTG /Bajaj Cat No.BJFL 120W LED I r or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of 200 watt LED flood light fitting wtih LED lamp secondary optics made in pressure die cast housing and heat sink in aluminium extrusion with IP65 protection with inbuilt surge protector and cable connection from looping box to light fitting and testing after and including taking down of old unserviceable fittings complete all as specified and directed. (Make:-Crompton Greaves Cat No.LFLN-200-CDL/60-M /Havells Cat No. JETAVALOURFL200WLED757PINTNBLTG/Bajaj Cat No. BJFL 200W LED I or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

S&F of 35/40 watts LED post top decorative lantern with LED lamp made in cast aluminium spigot housing with decorative opal polycarbonate diffuser and IP65 protection with suitable fixing arrangements such as lugs, glands, nuts,bolts and washers etc including necessary electric connection with suitable size copper wire after and including taken down of old unserviceable fittings complete all as specified and directed. (Make : Bajaj Model BGCS 40W LED WH /Havells cat No : CORALPT35WLED757PSYMTOPC /Crompton Greaves Cat No.LPTM-40-CDL or equivalent model/Cat No of make as per Appx 'A' as mentioned in PS here-in-after)

M&L for testing and commissioning of NATURE switch for outdoor lighting automation using space grade sensors and an advance micro controller suitable for outdoor use having feature automatic switching ON at Sunset, automatic switching OFF at dwan, no clock setting and time setting wide operating voltage range, high voltage trip and auto reset having specification 415 Volts, 50 Hz complete all connected accessories of rating 12 KW, 3 Phase, current range 40 Amps after and including taking down old unserviceable one complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode of size 600mm x 600mm x 6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised steel earth strip of size 32 x 6mm earth lead by means of nuts, bolts, check nuts, washers of galvanised iron as steel, protected by galvanised iron pipe 40mm bore (Medium grade) all as directed including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x10cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel, wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering, charcoal or coke and salt in alternate layers with necessary earth work in soft/loose soil all as shown in electrical plate No 3 of SSR Part I including testing on completion after and including taking out existing unserviceable earthing complete all as specified and directed . (Galvanised strip upto 7.5m including testing consider in this item).

M&L for providing cement concrete (1:2:4), type B-1 (using 20 mm graded crushed stone aggregate) for coping of poles including necessary form work and finished the surface complete all as specified and directed.

S&F of mild steel cross arms, bracings, supports, clamp and back plates fabricated from structural steel section including nuts, bolts, washers, welding, bending cold or hot drilling holes for bolts in any type, shape or as indicated and applying over two coats of aluminium paint over a coat of red oxide primer after and including dismantling existing unserviceable one complete all as specified and directed by Engr- in- charge.

M&L for steel tubular pole painting of any type/size/length and removing from existing pole painting by using wire brush and using with emery paper and cleaning with chemical agents after cleaning of steel tubular pole and GI brackets and cross arms etc and applying two coats of aluminium paint over a coat of red oxide primer. Upto 1.5 mtr from bottom painting works shall be carried out layer by layer of 30 cm with yellow and black paint and 15cm wide circle around the pole to be made by blue paint after black paint. Painting work shall be carried out at any height including marking of pole numbers marked with black paint over 20 cm yellow paint circle with all necessary safety equipments & tools complete all as specified and directed.

S&F for steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified conforming to IS- 2317/1980 type 410 SP-31 (9 metres long) complete with cast iron base plate including staying the poles in a truly vertical position till the foundations are properly set, including painting to pole (inside & outside) with two coats of aluminium paint on exposed surfaces of poles and two coat of black bituminous paint on embedded portion after and including taking down old unserviceable pole of any description complete all as specified and directed. (Note: Excavation, foundation concrete and coping will be measured and paid separately)

M&L for tree branches/vegitation cutting around the LT/HT lines and installations from line conductor to tree distance up to 4 mtrs and cutted wood pieces/vegitation materials disposal upto a distance not exceeding 100 mtr where indicated and including providing necessary safety eqpts & cutting tools, ladders etc will be contractors own arrangement and complete all as specified and directed. (Note:- quoted rate shall be of the following:- (1) Necessary safety measures will be fully responsible by tenderer (2) Due care shall be taken during tree branches, so that OH line should not be damaged. If damaged the same shall be rectified by the contractor without any extra cost.)

M&L for XLPE insulated, LT armoured electric cable with aluminium stranded conductor 1100 volts grade, cross-sectional area 16sqmm, 4 core laid in trenches/pipes/ducts/wall/borings with necessary cable lugs and glands, nuts, bolts and washers etc and testing after and including taking down existing cable of any type and any size complete all as specified and directed . (NOTE: Excavation/earth work, sand cushioning, cable cover/brick shall be measured and paid separately if required)

M&L for XLPE insulated, LT armoured electric cable with aluminium stranded conductor 1100 volts grade, cross-sectional area 25sqmm, 3.5 core laid in trenches/pipes/ducts/wall/borings with necessary cable lugs and glands, nuts, bolts and washers etc and testing after and including taking down existing cable of any type and any size complete all as specified and directed . (NOTE: Excavation/earth work, sand cushioning, cable cover/brick shall be measured and paid separately if required)

Excavation in trenches for laying under ground cable, foundation and erection of poles and stays in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 meter deep and getting out complete all as specified and directed

Returning, filling in, including spreading leveling, watering and well ramming in layers not exceeding 25cm soil all as specified and directed.

Removing surplus excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting points as in soft/loose soil all as specified and directed.

M&L for sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep including required watering and consolidation after laying and stretching the cable complete all as specified and directed.

M&L for brick covering with width equal to length of brick as protection to cable with well burnt sub class ‘B’ bricks of size 250mm x 125mm x 75mm laid dry flat complete all as specified and directed .

M&L for 63mm bore low density polyethylene pipes (HDPE) of pressure rating 6kgf/cm2 complete with all fittings in trenches, road/culvert crossing, floors, on roof, on pole for cable protection complete all as specified and directed.

M&L for two coats of plastic emulsion paint on concrete/ plaster surfaces (pole coping) of nay description over 10 cm girth or width complete all as specified and directed.

Supply, install, testing and commissioning LT outdoor floor mounted Bus Bar Box, powder coated, factory made and tested, platform mounted, suitable for 415 Volts, 3 Phase and neutral, 4 wire, 50 Hz, AC supply system of size 900mmX900mmX900mm (HXWXD) having bus bar chamber with inosulated electrolytic aluminium bus bars installed on DMC insulators. The panel shall be dust and vermin proof, protection clas (UP-54) in accordance with IS-2147 nad made of 3.15mm thick CRCA mild steel sheet and mild steel angle iron frame work (made out of 50mmX50mmX6mm thick and 900 mm long, front & rear opening type with aprons cable entry, with proper ferrule & cable gland, internal wiring with PVC insulate multistranded copper conductor FRLS cable of adequate size but not less than 1.5 sqmm complete. All steel metal works including frame shall be with anti-corrosive coating with seven tank process and finally epoxy polyster powder coating of flint grey shade having instument chamber with RYB indicator LED lamps including taking down old unserviceable Bus Bar Box. The scope of work also comprising of the following:- (a) Aluminium Bus bar chamber rating: 2X100 Amps (Double bus bar) (b) Incoming MCCB rating: 125 Amps, 4P, 25 KA-01 no (c) Outgoing MCCBS rating: 100 Amps, 4P, 25 KA- 02 Nos (NOTE: (i) Panel wiring for control circuit with copper flexible 1.5 sqmm & power wiring minimum 4 sqmm flexible or as per load rating of the feeder pillar box and provision of 300X300X2mm thick danger notice board on fron side of the panel doors. (ii) Complete installation with civil work and making necessary incoming and outgoing connection with proper cable lugs and clables glands is deemed to be included in unit rate quoted by the contractor. (iii) The final height of the LT panel from the normal ground leel shall be 450mm and necessary civil work included in quoted rate.

Supply, install, testing and commissioning LT outdoor floor mounted Bus Bar Box, powder coated, factory made and tested, platform mounted, suitable for 415 Volts, 3 Phase and neutral, 4 wire, 50 Hz, AC supply system of size 750mmX750mmX300mm (HXWXD) having bus bar chamber with inosulated electrolytic aluminium bus bars installed on DMC insulators. The panel shall be dust and vermin proof, protection clas (UP-54) in accordance with IS-2147 nad made of 3.15mm thick CRCA mild steel sheet and mild steel angle iron frame work (made out of 40mmX40mmX5mm thick and 900 mm long, front & rear opening type with aprons cable entry, with proper ferrule & cable gland, internal wiring with PVC insulate multistranded copper conductor FRLS cable of adequate size but not less than 1.5 sqmm complete. All steel metal works including frame shall be with anti-corrosive coating with seven tank process and finally epoxy polyster powder coating of flint grey shade having instument chamber with RYB indicator LED lamps including taking down old unserviceable Bus Bar Box. The scope of work also comprising of the following:- (a) Aluminium Bus bar chamber rating: 100 Amps , TPN, 415 V (b) Incoming MCCB rating: 63 Amps, 4P, 10 KA-01 no (NOTE: (i) Panel wiring for control circuit with copper flexible 1.5 sqmm & power wiring minimum 4 sqmm flexible or as per load rating of the feeder pillar box and provision of 300X300X2mm thick danger notice board on fron side of the panel doors. (ii) Complete installation with civil work and making necessary incoming and outgoing connection with proper cable lugs and clables glands is deemed to be included in unit rate quoted by the contractor. (iii) The final height of the LT panel from the normal ground leel shall be 450mm and necessary civil work included in quoted rate.

S&F in repairs of SMC kiosks box suitable for three phase, 415 volts, AC supply with 04 Nos aluminium bus bar rating 63 Amps with one No MCB 10 Amps, SP having size 300X270X200mm complete including making fixing arrangement with 9mtr long swaged pole with flat iron clamp complete all as specified and directed.

S&F of 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and over all PVC insulated in street light connection from pole junction box at bottom to street light fixed on 9 mtr long swaged pole by making two holes with welding machine for inserting cable of size 4sqmm 2 core multistranded including making all necessary connection after and including taking down existing unserviceable cable complete all as specified and directed.

Supply, fabricated and fixing of street light bracket made out of GI pipe 40mm dia medium grade bent to shape of 1.2 mtr long as directed including clamps made out of 40 mm x 6 mm flat iron for fixing bracket suitable for steel tubular poles including nuts and bolts, washers and other connected items of required size including painting with two coats of aluminium paint over a coat of red oxide primer after and including taking down old unserviceable brackets complete all as specified and directed.

M&L for boring holes horizontally under road without damaging the surface of road (minimum 1.0m bellow the road surfaces) with the help of GI tubing of any dia not exceeding 100mm dia for passing of UG cable complete all as specified and directed.

DEYS ENTERPRISE

INDUSTRIAL CONSTRUCTION

R.S. COMPANY

M/s S K SHARMA

M/S D K Singha

S..S. ELECTRIC CO.

CHATTERJEE ENTERPRISE