SPL REPAIRS TO BLDG NO T-25 AND T-27 (OTM ACCN) AT 4 COSR IN ZONE 3 A UNDER GE (S) TEZPUR

Amount

Dismantling of Asbestos cement (corrugated or semicorrugated etc) sheets in roof coverings complete all as specified and directed.

Dismanting timber scantling 40 Sqcm and over in secion in any position in framed work or unframed work complete all as specified and directed.

All as per Ser Itme no 2 above but In fillets, rails , posts, refters and purlins etc under 40 sqcm in section unframed work complete all as specified and directed.

Dismanting of wall /ceiling board (Fibre pulp insulation) or insulation boards any thickness including cover fillets complete all as specified and directed.

Dismantling timber boarding of any description fixed in any position complete all as specified and directed

Demolition of reed lathing, single or double including battens and plasters or checken wire lathing complete all as specified and directed.

Dismantling floor hearth wall tiling including cement mortar bedding(but not backing) complete all as specified and directed.

Dismantling Structural steel work includings door, gates, etc and similar works complete all as specified and directed

Taking down shutters of any description exc 1 sqm and n exe 2 sqm complete all as specified and directed.

Taking down chowkhat with shutter/without taking off shutter from the frame n exc 1.50 each complete all as specified and directed.

Taking down cement plaster, of any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness complete all as specified and directed.

S&F 0.5mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour ,tensile strength of 550Mpa as in roof covering ,cladding to wall ,ridge,gutter etc fixed with self tapping screws complete all as specified and directed.

All as per item No.12 above but plain sheet for ridge ,gutter, eaves board, etc fixed with self tapping screws complete all as specified and directed

M&L 2nd class hardwood in scantling fixed clean swan in framed work complete all as specified and directed

M&L 2nd CL hardwood plain fillets square, rectangular or triangular in section clean sawn sectional area exc 6 sqcm & n exc 13 sqcm fixed with nails complete all as specified and directed

S&F Exposed GI powder coated snap grid frame for false ceiling 600x600mm size of wall angle 25x25x0.25mm size of cross tee and main tee 26x24x0.25mm and 32mm x 24mm x 0.25mm with 1.5mm dia double GI suspenler including supply and fixing of 4mm thick E Board decorative type in false ceiling including fixing arrangement from steel tress or any type of tress complete all as specified and directed (Make: E Board Everest or equivalent as approved by GE)

S&F of joist, channel, angle, flat iron or Tee sections, fixed independently with connecting plates, etc confirming to Fe 410-W (Gde 250 quality A) complete all as specified and directed.

S&F MS framed works such as grills grating etc with ends of bars shouldered and for rivetted in forged into spikes, framed guard bars, railing and similar work confirming to Fe-410-0 or Fe 310-0 complete all as specified and directed

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed

S&F Anodised aluminium window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.complete all as specified and directed

S&F 30mm thick 2nd class hard wood factory made flush shutter solid core construction with block board core and plywood face panels commercial type of both side complete all as specified and directed.

S&F 30 mm thick 2nd class hard wood Glazed and skelton shutter open rebated and prepared to receive glass, gauze etc (without sash bars) edges of the framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members as specified in SSR Pt I clasue 8.24 (a) complete all as specified and directed

S&F 2nd class hard wood small fitting such as brackets of any type latch and hinge blocks,shaped door and window stops and the like including all necessary labours articles n.exc 200 cucm each complete all as specified and directed

S&F 50mm long MS butt hinges medium weight cold rolled complete all as specified and directed

S&F MS 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed

S&F 150mm long aluminium handle, fabricated type anodised complete all as specified and directed

S&F Aluminium anodised barrel tower bolts of extruded section 200 mm long and fixed with screws complete all as specified and directed

S&F 100mm Butt hinges medium weight cold rolled mild steel complete all as specified and directed

S&F MS sliding door bolts plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed length of the bolt in 300 mm dia 16mm complete all as specified and directed

M&L for Machine cut kota stone slab flooring 20-25mm thick over 20mm thk cement screed base in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed

M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado over 10mm thick cement screed base in CM ( 1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

S& F 4.0 mm thick sheet glass ordinary quality and glazing with oil putty in squares exc 0.5 sq. m in each pane in squares complete all as specified and directed

S&F as in repair galvanised mild steel wire 0.36mm nominal dia of wire & average width of aperatre 1.18mm fixed with fixed with tinned tacks or galvanised wire staples complete all as specified and directed

S&F as in repair galvanised mild steel wire 0.56mm nominal dia of wire & average width of aperatre 1.18mm fixed with fixed with tinned tacks or galvanised wire stapples complete all as specified and directed

M&L 15mm thick rendering in CM (1:4) on one side of lathing finishedd even and smooth without using extra cement including 0.71mm chicken wire and size of mesh 12mm complete all as specified and directed

M&L 10mm thick rendering in CM (1:6) on other side of lathing finished even and smooth complete all as specified and directed

M & L, 15mm thick rendering in C.M. (1:4) on fair faces of brick work finished even and smooth without using extra cement complete all as specified and directed

M & L, 10mm thick rendering in C.M. (1:6) on brick work finished even and smooth without using extra cement complete all as specified and directed

Supply and fix as in repair 20mm dia curtain rails, mild steel, chorium plated, with fixing brackets, stops, rollers etc complete all as specified and directed

M&L applying two coats of Oil bound distember to newly plastered/previously untreated wall over a coat of primer including preparation of newly platsered wall complete all as specified and directed

M&L applying two coats of Oil bound distember to old decorated plastered surfaces wall over a coat of 1 mm layer wall care putty over a coat of primer including complete removal of existing treatment all as specefied and directed..

M&L complete removal of existing treatment on old decorated plastered surfaces of wall and applying two coat of cement base paint complete all as specified and directed

M&L applying two coats of cement base paint to newely plaster/previously untreated walls over a coat of primer including preparation complete all as specefied and directed

M&L 75mm thick plain cement concrete (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection and finishing surfaces of concrete fair and even including making construction joint at interval of 1.2 mtr & filled with bituminous filler complete all as specified and as directed

M&L 100mm thick cement concrete (1:2:4) type B1 using 20mm graded stone aggregate) as in sub bases, floors and Pavings complete all as specified and directed

M&L preparing surfaces of wood & wood based materials new or old at any description & girth not otherwise described & treated with tar or coal tar black paint complete all as specified and directed

M&L preparation of old painted steel surfaces over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L preparation of old painted wooden surfaces over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of new wooden surfaces n.exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer completed all as specified and directed

E/M Portion:- Taking down carefully unserviceable point wiring (light,fans,socket etc) complete incl battens and fittings such as switch, ceiling rose,light fittings, regulatos, socket etc and making good disturbed surface of wall/floor etc complete all as specified and directed

Taking down DB/main switch of any size and making good disturbed surface of wall/floor complete all as specified and directed

Taking down sub main wiring of any size complete and making good disturbed surface of walls/floors etc complete all as specified and directed

M & L for taking down fans sealing cable ends dismantling blades and removing fan and keeping in safe custody for reuse complete all as specified and directed

Taking down old U/S LED light fittings any type and size complete all as specified and directed

M & L for point wiring for one light /fan point with 1.5 sqmm cable PVC insulated copper conductor multi stranded as per IS-694 FRLS cable controlled by one way switch, drawn through PVC Casing Capping with all accessories incl 1.5 sqmm multi strand copper conductor cable (green colour) PVC insulated and unsheathed for earth continuity connected to common earth dolly and sunken cast pressed steel terminal box fixed flush to wall of not less than 1.6 mm thick for mounting of fittings such as switch, socket and speed regulator with 3 mm thick Laminated bakelite sheet (Make' Hylum') cover complete all as specified and directed

All as per item No 58 above but for 5 amps socket on same board with other switches complete all as specified and directed

All as per item No 58 above but for 5 amps socket on independent board complete all as specified and directed

All as per item No 58 above but with 2.5 sqmm cables for 15 amps switch socket combination outlet on independent board complete all as specified and directed.

Supply and fix switch 5 amps switch flush type one way single pole complete all as specified and directed.

Supply and fix switch socket combination outlet flush type multi pin 5 amps complete all as specified and directed.

Supply and fix switch socket combination outlet universal type 5 pin 5/16 amps complete all as specified and directed.

Supply and fix ceiling rose surface backelite 65x50 mm having 3 terminal complete all as specified and directed.

Supply and fix ceiling fan regulator Electronic rotary Step type 80 watt single phase A/C 230 volts all complete as specified and directed

Supply and fix Circuit/Sub Main Wiring with 2x4.0 Sqmm PVC insulated, FRLS, copper cable 1100 volts grade stranded copper conductor cable drawn through and including PVC concealed conduit with all fittings and accessories including PVC box (IS-14772) and 2.5 Sqmm stranded PVC unsheathed copper cable for earth continuity connected to common earth dolly complete all as specified and directed.

S&F PVC angular holder polycarbonate complete all as specified and directed.

Supply & fix Basic all purpose surface and wall mounted LED batten with Aluminum housing & integrated electronic driver complete all as specified and directed. Cat No LUMILINEPLUSBS18WLED865SPCSS Make: Havells or equivalent

S & F MCB DB Single pole and neutral 12 way double door with 200 amps rated bus bar complete all as specified and directed.

S&F MCB SPN 63 Amp, 'C' Series, 10KA braking capacity 230/240 volt AC acomplete all as specified and directed.

S & F MCB SP 6 to 32 Amps 240 volts having 'B' Series complete all as specified and directed.

Hanging/fixing only fans/geysers and connecting up including replacement of cable from ceiling rose to connector complete all as specified and directed.

Supply & fix fans ceiling complete with electronic type regulator and accessories 230 V , 1400 mm sweep complete all as specified and directed.

Supply and fix fan hook /clamps made out by GI strip 20 mm width 4 mm thick incl cutting, bending, fitting, painting ,nut bolts washers etc all as site suitable for fitting to ceiling fan complete all as specified and directed.

Supply and fix Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head Back-lit LED luminaire comprising of high brightness LEDs. Cat Ref: HEXAFT10WLED857SSYMBOPC of Make: Havells or equivalent

M/L for Earthing complete with galvanized steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 meter below normal ground level connected to GI earth lead wire 4 mm dia by means of bolts nuts, check nut and washers of GI and GI tubing 15 mm bore, light grade for earth lead protection up to main earth test point and includingconcrete pit in PCC (1:3:6) typeC 1 pre cast RCC (1:2:4) type B1 cover slab 450 x 450 x 50 mm with one handle for lifting made out of 8 mm dia MS bar, wire mash, 20 mm bore GI tubing(L. G.) for watering ,charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed Electrical plate no 3 of SSR Part-I.

Supply and laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 sq mm 2 core complete all as specified and directed

Excavation in trenches n.exc 1.5 mtr wide and n exc 1.5 mtr in depth and getting out in soft/ loose for laying cables, etc. complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed

Removing excavated material in soils n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed

Supply and laying Bricks; common burnt clay building bricks, sub-class ‘B’ designation 75 complete all as specified and directed

M&L for sand cushioning with clean dry sand for protection of under ground cable complete all as specified and as directed. Note :- Punned thickness of sand layer shall be measured abd paid to

Supply/ laid/ fixing of galvanised steel water tubing light grade bore of dia 40 mm with all fittings complete all as specified and directed

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the IRC specifications shall be followed. 2. Unless otherwise specified the rates for PCC shall deemed to include the cost of formwork shuttering etc., required for complete and proper execution of the work. Refer Schedule "A" notes for details.

Sidhartha Bora

OM CONSTRUCTIONS

M/S MOHANPASARI

M/S Bharat Construction Co.

D G Corporation

M/s KRISHNA CONSTRUCTIONS